M74HC257

M 54/M74HC257 M54/M74HC258 HC257 QUAD 2 CHANNEL MULTIPLEXER (3-STATE) HC258 QUAD 2 CHANNEL MULTIPLEXER (3-STATE, INVERTING) . . . . . . . . HIGH SPEED tPD = 10 ns (TYP.) at VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) at TA = 25 °C HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 15 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 6 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V to 6 V PIN AND FUNCTION COMPATIBLE WITH 54/74LS257/258 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HCXXXF1R M74HCXXXM1R M74HCXXXB1R M74HCXXXC1R PIN CONNECTIONS (top view) HC257 DESCRIPTION The M54/74HC257 and the M54/74HC258 are high speed CMOS MULTIPLEXERs fabricated with sili2 con gate C MOS technology. They have the same high speed performance of LSTTL combined with true CMOS low power consumption. These IC’s are composed of an independent 2channel multiplexer with common SELECT and ENABLE INPUT. The M54/74HC258 is an inverting multiplexer while the M54/74HC257 is a non-inverting multiplexer. When the ENABLE INPUT is held ”High”, outputs of both IC’s become high-impedance state. If SELECT INPUT is held ”Low”, ”A” data is selected, when SELECT INPUT is high ”H”, ”B” data is chosen. All inputs are equipped with protection circuits against static discharge and transient excess voltage. October 1992 HC258 1/12 M54/M74HC257/258 I NPUT AND OUTPUT EQUIVALENT CIRCUIT CHIP CARRIER HC257 HC258 NC = No Internal Connection PIN DESCRIPTION (HC257) PIN No 1 2, 5, 14, 11 3, 6, 13, 10 4, 7, 12, 9 15 8 16 SYMBOL SELECT 1A to 4A 1B to 4B 1Y to 4Y OE GND V CC NAME AND FUNCTION Common Data Select Input Data Input From Source A Data Inputs from Source B 3 State Multiplexer Outputs 3 State Output Enable Inputs (Active LOW) Ground (0V) Positive Supply Voltage PIN DESCRIPTION (HC258) PIN No 1 2, 5, 14, 11 3, 6, 13, 10 4, 7, 12, 9 15 8 16 SYMBOL SELECT 1A to 4A 1B to 4B 1Y to 4Y OE GND VCC NAME AND FUNCTION Common Data Select Input Data Input From Source A Data Inputs from Source B 3 State Multiplexer Outputs 3 State Output Enable Inputs (Active LOW) Ground (0V) Positive Supply Voltage 2/12 M54/M74HC257/258 I EC LOGIC SYMBOL HC257 HC258 LOGIC DIAGRAM HC257 HC258 TRUTH TABLE INPUTS OE H L L L L SELECT X L L H H A X L H X X B X X X L H Y (257) Z L H L H OUTPUTS Y (258) Z H L H L X = DON’T CARE Z = HIGH IMPEDANCE 3/12 M54/M74HC257/258 A BSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO ICC or IGND PD Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Source Sink Current Per Output Pin DC VCC or Ground Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 35 ± 70 500 (*) -65 to +150 300 Unit V V V mA mA mA mA mW o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top tr, tf Parameter Supply Voltage Input Voltage Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time Value 2 to 6 0 to VCC 0 to VCC -55 to +125 -40 to +85 0 to 1000 0 to 500 0 to 400 Unit V V V C o C ns o VCC = 2 V VCC = 4.5 V VCC = 6 V 4/12 M54/M74HC257/258 D C SPECIFICATIONS Test Conditions Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 VOL Low Level Output Voltage 2.0 4.5 6.0 4.5 6.0 II IOZ ICC Input Leakage Current Output Leakage Current Quiescent Supply Current 6.0 6.0 6.0 1.9 4.4 5.9 4.18 5.68 2.0 4.5 6.0 4.31 5.8 0.0 0.0 0.0 0.17 0.18 0.1 0.1 0.1 0.26 0.26 ±0.1 ±0.5 4 TA = 25 oC 54HC and 74HC Min. 1.5 3.15 4.2 0.5 1.35 1.8 VI = IO=-20 µA VIH or V IL IO=-6.0 mA IO=-7.8 mA VI = IO= 20 µA VIH or V IL IO= 6.0 mA IO= 7.8 mA VI = VCC or GND VI = VIH or VIL VO = VCC or GND VI = VCC or GND 1.9 4.4 5.9 4.13 5.63 0.1 0.1 0.1 0.33 0.33 ±1 ±5 40 Typ. Max. Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.10 5.60 0.1 0.1 0.1 0.40 0.40 ±1 ±10 80 µA µA µA V V Max. Min. 1.5 3.15 4.2 0.5 1.35 1.8 V Max. V Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage V IL V OH 5/12 M54/M74HC257/258 A C ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 tPLZ tPHZ CIN COUT CPD (*) Output Disable Time Input Capacitance Output Capacitance Power Dissipation Capacitance 6.0 2.0 4.5 6.0 50 RL = 1 KΩ CL (pF) TA = 25 C 54HC and 74HC Min. Typ. 25 7 6 45 13 11 62 18 15 45 13 11 62 18 15 RL = 1 KΩ 40 12 10 57 17 14 28 14 13 5 10 47 Max. 60 12 10 100 20 17 140 28 24 100 20 17 140 28 24 110 22 19 150 30 26 140 28 24 10 o Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. 75 15 13 125 25 21 175 35 30 125 25 21 175 35 30 140 28 24 190 38 32 175 35 30 10 Min. Max. 90 19 15 150 30 26 210 42 36 150 30 26 210 42 36 165 33 28 225 45 38 210 42 36 10 Unit tTLH tTHL tPLH tPHL Output Transition Time Propagation Delay Time (A, B - Y) 50 ns 50 ns 150 ns tPLH tPHL Propagation Delay Time (SELECT - Y) 50 ns 150 ns tPZL tPZH Output Enable Time 50 ns 150 RL = 1 KΩ ns ns pF pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/4 (per Channel) 6/12 M54/M74HC257/258 SWITCHING CHARACTERISTICS TEST WAVEFORM TEST CIRCUIT ICC (Opr.) C PD CALCULATION CPD is to be calculated with the following formula by using the measured value of ICC (opr.) in the test circuit opposite. ICC ( opr) CPD = fIN × VCC INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERSISTICSTESt. 7/12 M54/M74HC257/258 Plastic DIP16 (0.25) MECHANICAL DATA mm MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP. MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 inch TYP. MAX. DIM. P001C 8/12 M54/M74HC257/258 Ceramic DIP16/1 MECHANICAL DATA mm MIN. A B D E e3 F G H L M N P Q 7.8 2.29 0.4 1.17 0.22 0.51 0.38 17.78 2.79 0.55 1.52 0.31 1.27 10.3 8.05 5.08 0.307 0.090 0.016 0.046 0.009 0.020 3.3 0.015 0.700 0.110 0.022 0.060 0.012 0.050 0.406 0.317 0.200 TYP. MAX. 20 7 0.130 MIN. inch TYP. MAX. 0.787 0.276 DIM. P053D 9/12 M54/M74HC257/258 SO16 (Narrow) MECHANICAL DATA DIM. MIN. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8° (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45° (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm TYP. MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.004 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 P013H 10/12 M54/M74HC257/258 PLCC20 MECHANICAL DATA mm MIN. A B D d1 d2 E e e3 F G M M1 1.27 1.14 7.37 1.27 5.08 0.38 0.101 0.050 0.045 9.78 8.89 4.2 2.54 0.56 8.38 0.290 0.050 0.200 0.015 0.004 TYP. MAX. 10.03 9.04 4.57 MIN. 0.385 0.350 0.165 0.100 0.022 0.330 inch TYP. MAX. 0.395 0.356 0.180 DIM. P027A 11/12 M54/M74HC257/258 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. © 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 12/12