M74HC375M1R

M 54HC375 M74HC375 QUAD D TYPE LATCH . . . . . . . . HIGH SPEED tPD = 14 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 1 µA (MAX.) AT TA = 25 °C HIGH NOISE IMMUNITY VNIH = VNIL = 28 % VCC (MIN.) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE |IOH| = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V TO 6 V PIN AND FUNCTION COMPATIBLE WITH 54/74LS375 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HC375F1R M74HC375M1R M74HC375B1R M74HC375C1R PIN CONNECTIONS (top view) DESCRIPTION The M54/74HC375 is a high speed CMOS QUAD D TYPE LATCH fabricated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOSlow power consumption. It contains two groups of 2-bit latches controlled by an enable input (G1 . 2 or G3 . 4). These two latch groups can be used in the different circuits. Each latch has Q and Q outputs (1Q to 4Q and 1Q to 4Q). The data applied to the data input is transferred to the Q and Q outputs when the enable input is taken high and the outputs will follow the data input as long as the enable input is kept high. When the enable input is taken low, the information data applied to the data input at that time is retained at the outputs. All inputs are equipped with protection circuits against static discharge and transient excess voltage. February 1993 NC = No Internal Connection 1/11 M54/M74HC375 TRUTH TABLE INPUTS D L H X X: DON’T CARE OUTPUTS G H H L Q L H Qn Q H L Qn FUNCTION LATCH LOGIC DIAGRAM I NPUT AND OUTPUT EQUIVALENT CIRCUIT 2/11 M54/M74HC375 P IN DESCRIPTION PIN No 1, 7, 9, 15 3, 5, 11, 13, 2, 6, 10, 14 4 12 8 16 SYMBOL 1D to 4D 1Q to 4Q 1Q to 4Q G1- 2 G3 - 4 GND V CC NAME AND FUNCTION Data Inputs Outputs Enable Input Enable Input Ground (0V) Positive Supply Voltage IEC LOGIC SYMBOL ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO ICC or IGND PD Tstg TL Parameter Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Source Sink Current Per Output Pin DC VCC or Ground Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500 (*) -65 to +150 300 Unit V V V mA mA mA mA mW o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top tr, tf Parameter Supply Voltage Input Voltage Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time VCC = 2 V VCC = 4.5 V VCC = 6 V Value 2 to 6 0 to VCC 0 to VCC -55 to +125 -40 to +85 0 to 1000 0 to 500 0 to 400 Unit V V V C o C o ns 3/11 M54/M74HC375 D C SPECIFICATIONS Test Conditions Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 V OH High Level Output Voltage 2.0 4.5 6.0 4.5 VOL Low Level Output Voltage 6.0 2.0 4.5 6.0 4.5 6.0 II ICC Input Leakage Current Quiescent Supply Current 6.0 6.0 VI = IO=-20 µA VIH or V IL IO=-4.0 mA IO=-5.2 mA VI = IO= 20 µA VIH or V IL IO= 4.0 mA IO= 5.2 mA VI = VCC or GND VI = VCC or GND 1.9 4.4 5.9 4.18 5.68 2.0 4.5 6.0 4.31 5.8 0.0 0.0 0.0 0.17 0.18 0.1 0.1 0.1 0.26 0.26 ±0.1 2 TA = 25 oC 54HC and 74HC Min. Typ. Max. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.13 5.63 0.1 0.1 0.1 0.33 0.33 ±1 20 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.10 5.60 0.1 0.1 0.1 0.40 0.40 ±1 40 µA µA V V 1.5 3.15 4.2 0.5 1.35 1.8 V V Unit VIH High Level Input Voltage Low Level Input Voltage V IL 4/11 M54/M74HC375 A C ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 5 52 TA = 25 oC 54HC and 74HC Min. Typ. Max. 30 8 7 56 14 12 52 13 11 12 3 3 20 5 4 75 15 13 115 23 20 105 21 18 75 15 13 75 15 13 0 0 0 10 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 95 19 16 145 29 25 130 26 22 95 19 16 95 19 16 0 0 0 10 110 22 19 175 35 30 160 32 27 115 23 20 115 23 20 0 0 0 10 ns pF pF ns ns ns ns ns Unit tTLH tTHL tPLH tPHL tPLH tPHL t(W)H Output Transition Time Propagation Delay Time (DATA - Q, Q) Propagation Delay Time (G - Q, Q) Minimum Enable Pulse Width (G) Minimum Set-up Time (DATA - G) Minimum Hold Time (DATA - G) Input Capacitance Power Dissipation Capacitance ts th CIN CPD (*) (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC 5/11 M54/M74HC375 SWITCHING CHARACTERISTICS TEST WAVEFORM TEST CIRCUIT ICC (Opr.) INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST. 6/11 M54/M74HC375 Plastic DIP16 (0.25) MECHANICAL DATA mm MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP. MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 inch TYP. MAX. DIM. P001C 7/11 M54/M74HC375 Ceramic DIP16/1 MECHANICAL DATA mm MIN. A B D E e3 F G H L M N P Q 7.8 2.29 0.4 1.17 0.22 0.51 0.38 17.78 2.79 0.55 1.52 0.31 1.27 10.3 8.05 5.08 0.307 0.090 0.016 0.046 0.009 0.020 3.3 0.015 0.700 0.110 0.022 0.060 0.012 0.050 0.406 0.317 0.200 TYP. MAX. 20 7 0.130 MIN. inch TYP. MAX. 0.787 0.276 DIM. P053D 8/11 M54/M74HC375 SO16 (Narrow) MECHANICAL DATA DIM. MIN. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8° (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45° (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm TYP. MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.004 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 P013H 9/11 M54/M74HC375 PLCC20 MECHANICAL DATA mm MIN. A B D d1 d2 E e e3 F G M M1 1.27 1.14 7.37 1.27 5.08 0.38 0.101 0.050 0.045 9.78 8.89 4.2 2.54 0.56 8.38 0.290 0.050 0.200 0.015 0.004 TYP. MAX. 10.03 9.04 4.57 MIN. 0.385 0.350 0.165 0.100 0.022 0.330 inch TYP. MAX. 0.395 0.356 0.180 DIM. P027A 10/11 M54/M74HC375 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. © 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 11/11