M74HC4066M1R

M74HC4066 QUAD BILATERAL SWITCH s s s s s s s HIGH SPEED: tPD = 7ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA=25°C LOW "ON" RESISTANCE: RON = 50Ω TYP. AT VCC = 9V, II/O = 100 µA WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2V TO 12V SINE WAVE DISTORTION: 0.042% at VCC = 4V f = 1KHz HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 4066 DIP SOP TSSOP ORDER CODES PACKAGE DIP SOP TSSOP TUBE M74HC4066B1R M74HC4066M1R T&R M74HC4066RM13TR M74HC4066TTR DESCRIPTION The M74HC4066 is an high speed CMOS QUAD BILATERAL SWITCH fabricated with silicon gate C2MOS technology. The C input is provided to control the switch; the switch is on when the C input is held high and off when C is held low. PIN CONNECTION AND IEC LOGIC SYMBOLS July 2001 1/11 M74HC4066 LOGIC DIAGRAM PIN DESCRIPTION PIN No 1, 4, 8, 11 2, 3, 9, 10 13, 5, 6, 12 7 14 SYMBOL 1 to 4 I/O 1 to 4 O/I 1C to 4C GND VCC NAME AND FUNCTION Independent Inputs/Outputs Independent Outputs/ Inputs Enable Inputs (Active High) Ground (0V) Positive Supply Voltage TRUTH TABLE CONTROL H L SWITCH FUNCTION ON OFF ABSOLUTE MAXIMUM RATINGS Symbol VCC VIN VI/O IOK IIOK IO Supply Voltage DC Input Voltage DC Input/Output Voltage Control Input DC Diode Current I/O DC Diode Current DC Output Source Sink Current Per Output Pin Parameter Value -0.5 to +13 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500(*) -65 to +150 300 Unit V V V mA mA mA mA mW °C °C ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg TL Storage Temperature Lead Temperature (10 sec) Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VIN VI/O Top Supply Voltage Input Voltage (Control) I/O Voltage Operating Temperature Input Rise and Fall Time tr, tf VCC = 2.0V VCC = 4.5V VCC = 6.0V VCC = 10.0V Parameter Value 2 to 12 0 to VCC 0 to VCC -55 to 125 0 to 1000 0 to 500 0 to 400 0 to 250 ns Unit V V V °C 2/11 M74HC4066 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 4.5 VI = VIHC 9.0 VI/O = VCC to GND II/O ≤ 1mA 12.0 4.5 VI = VIHC 9.0 VI/O = VCC or GND II/O ≤ 1mA 12.0 4.5 VI = VIHC 9.0 VI/O = VCC or GND II/O ≤ 1mA 12.0 VOS = VCC or GND 12.0 VIS = VCC or GND VIN = VILC 12.0 6.0 6.0 9.0 12.0 VOS = VCC or GND VIN = VIHC VI = VCC or GND VI = VCC or GND TA = 25°C Min. 1.5 3.15 6.3 8.4 0.5 1.35 2.7 3.6 170 85 80 100 75 70 Typ. Max. Value -40 to 85°C Min. 1.5 3.15 6.3 8.4 0.5 1.35 2.7 3.6 200 100 90 130 95 90 Max. -55 to 125°C Min. 1.5 3.15 6.3 8.4 0.5 1.35 2.7 3.6 250 150 120 160 115 110 Max. Unit VIHC High Level Control Input Voltage V VILC Low Level Control Input Voltage V RON ON Resistance ∆RON Difference of ON Resistance between switches Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Current Quiescent Supply Current 96 55 45 70 50 45 10 5 5 Ω Ω IOFF ± 0.1 ±1 ±2 µA IIZ ± 0.1 ± 0.1 1 4 8 ±1 ±1 10 40 80 ±2 ±1 20 80 160 µA µA µA IIN ICC 3/11 M74HC4066 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter VCC (V) TA = 25°C Min. Typ. 10 4 3 3 18 8 6 6 20 10 8 8 30 30 30 30 Max. 50 10 8 7 100 20 12 12 115 23 20 18 Value -40 to 85°C Min. Max. 65 13 10 9 125 25 22 18 145 29 25 22 -55 to 125°C Min. Max. 75 15 13 10 150 30 27 25 175 35 30 27 Unit ΦI/O Phase Difference Between Input and Output tPZL tPZH tPLZ tPHZ 2.0 4.5 9.0 12.0 Output Enable Time 2.0 4.5 9.0 12.0 Output Disable 2.0 Time 4.5 9.0 12.0 Maximum Control 2.0 Input Frequency 4.5 9.0 12.0 ns RL = 1KΩ ns RL = 1KΩ ns RL = 1KΩ CL = 15 pF VOUT = 1/2 VCC MHz CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) TA = 25°C Min. Typ. 5 6 0.5 15 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF pF pF Unit CIN CI/O CIOS CPD Input Capacitance Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 4/11 M74HC4066 ANALOG SWITCH CHARACTERISTICS (GND = 0V;TA = 25°C) Symbol Parameter VCC (V) Sine Wave Distortion (THD) fMAX Frequency Response (Switch ON) Feed through Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) Crosstalk (Between Any Switches) 4.5 9.0 4.5 9.0 4.5 9.0 4.5 9.0 4.5 9.0 VIN (Vp-p) 4 8 fIN = 1 KHz RL = 10 KΩ, CL = 50 pF Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF VIN is centered at VCC/2. Adjust input for 0 dBm RL = 600Ω CL = 50 pF, fIN = 1MHz sine wave RL = 600Ω, CL = 50 pF, fIN = 1MHz square wave (tr = tf =6ns) Adjust VIN to Obtain 0 dBmat input RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave Test Condition Value Typ. 0.05 0.04 200 200 -60 -60 60 100 -60 -60 % Unit MHz dB mV dB 5/11 M74HC4066 SWITCHING CARACTERISTICS TEST CIRCUIT CROSSTALK (control to output) CROSSTALK BETWEEN ANY TWO SWITCHES BANDWIDTH AND FEEDTHROUGH ATTENUATION MAXIMUM CONTROL FREQUENCY 6/11 M74HC4066 CHANNEL RESISTANCE (RON) ICC (Opr.) 7/11 M74HC4066 Plastic DIP-14 MECHANICAL DATA mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 1.27 3.3 2.54 0.050 8.5 2.54 15.24 7.1 5.1 0.130 0.100 0.51 1.39 0.5 0.25 20 0.335 0.100 0.600 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.055 0.020 0.010 0.787 0.065 TYP. MAX. inch P001A 8/11 M74HC4066 SO-14 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8° (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45° (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 PO13G 9/11 M74HC4066 TSSOP14 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0° 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8° 0.75 0° 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8° 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 10/11 M74HC4066 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 11/11