M74HCT132

M74HCT132 QUAD 2-INPUT SCHMITT NAND GATE s s s s s s HIGH SPEED: tPD = 19ns (TYP.) at VCC = 4.5V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY : VH = 0.7V (TYP) at Vcc = 4.5V BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 132 DIP SOP TSSOP ORDER CODES PACKAGE DIP SOP TSSOP TUBE M74HCT132B1R M74HCT132M1R T&R M74HCT132RM13TR M74HCT132TTR DESCRIPTION The M74HCT132 is an high speed CMOS QUAD 2-INPUT SCHMITT NAND GATE fabricated with silicon gate C2MOS technology. Pin configuration and function are the same as those of the M74HCT00. The hysteresis characteristics (around 20% Vcc) of all inputs allow slowly changing input signals to be transformed into sharply defined jitter-free output signals. The M74HCT132 is designed to directly interface HSC2MOS systems with TTL and NMOS components. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION AND IEC LOGIC SYMBOLS July 2001 1/8 M74HCT132 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1, 4, 9, 12 2, 5, 10, 13 3, 6, 8, 11 7 14 SYMBOL 1A to 4A 1B to 4B 1Y to 4Y GND VCC NAME AND FUNCTION Data Inputs Data Inputs Data Outputs Ground (0V) Positive Supply Voltage TRUTH TABLE A L L H H B L H L H Y H H H L ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO PD Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500(*) -65 to +150 300 Unit V V V mA mA mA mA mW °C °C ICC or IGND DC VCC or Ground Current Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top Supply Voltage Input Voltage Output Voltage Operating Temperature Parameter Value 4.5 to 5.5 0 to VCC 0 to VCC -55 to 125 Unit V V V °C 2/8 M74HCT132 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 4.5 5.5 4.5 5.5 4.5 5.5 4.5 4.5 5.5 5.5 IO=-20 µA IO=-4.0 mA IO=20 µA IO=4.0 mA VI = VCC or GND VI = VCC or GND TA = 25°C Min. 1.2 1.4 0.5 0.6 0.4 0.4 4.4 4.18 Typ. 1.55 1.75 0.85 1.1 0.7 0.7 4.5 4.31 0.0 0.17 0.1 0.26 ± 0.1 1 Max. 1.9 2.1 1.2 1.4 1.4 1.5 Value -40 to 85°C Min. 1.2 1.4 0.5 0.6 0.4 0.4 4.4 4.13 0.1 0.33 ±1 10 Max. 1.9 2.1 1.2 1.4 1.4 1.5 -55 to 125°C Min. 1.2 1.4 0.5 0.6 0.4 0.4 4.4 4.10 0.1 0.40 ±1 20 Max. 1.9 2.1 1.2 1.4 1.4 1.5 V V V V V µA µA Unit VP VN VH VOH VOL II ICC High Level Threshold Voltage Low Level Threshold Voltage Hysteresis Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter VCC (V) 4.5 4.5 TA = 25°C Min. Typ. 8 19 Max. 15 30 Value -40 to 85°C Min. Max. 19 38 -55 to 125°C Min. Max. 22 45 ns ns Unit tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) TA = 25°C Min. Typ. 5 45 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF Unit CIN CPD Input Capacitance Power Dissipation Capacitance (note 1) 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 3/8 M74HCT132 TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1: PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle) 4/8 M74HCT132 Plastic DIP-14 MECHANICAL DATA mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 1.27 3.3 2.54 0.050 8.5 2.54 15.24 7.1 5.1 0.130 0.100 0.51 1.39 0.5 0.25 20 0.335 0.100 0.600 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.055 0.020 0.010 0.787 0.065 TYP. MAX. inch P001A 5/8 M74HCT132 SO-14 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8° (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45° (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 PO13G 6/8 M74HCT132 TSSOP14 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0° 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8° 0.75 0° 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8° 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 7/8 M74HCT132 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 8/8