M74HCT137B1R

M 54HCT137 M74HCT137 3 TO 8 LINE DECODER/LATCH (INVERTING) . . . . . . . HIGH SPEED tPD = 17 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) AT TA = 25 °C COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL PIN AND FUNCTION COMPATIBLE WITH 54/74LS137 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) DESCRIPTION The M54/74HCT137 is a high speed CMOS3TO8LINE DECODER/LATCH (INVERTING) fabricated in silicon 2 gateC MOStechnology. Ithas the samehigh speed performance ofLSTTL combined with trueCMOSlow power consumption. This device is a 3 to 8 line decoder with latches onthe three address inputs. When GLgoes from low to high, the address present at the select inputs (A, B and C) is stored in the latches. As long as GLremains high no address changes will be recognized. Output enable pins G1 and G2, control the state of the outputs independently ofthe select orlatch-enable inputs. All theoutputs are high unless G1 is high and G2 is low. The HC137 is ideally suited for the implementation of glitch-free decoders in stored-address applications in bus oriented systems. All inputs are equipped with protection circuits against static discharge and transient excess voltage.This integrated circuit has input and output characteristics that are fully compatible with 54/74 LSTTL logic families. M54/74HCT devices aredesigned todirectly interfaceHSC2MOS systems with TTL and NMOS components. They are also plug in replacements for LSTTL devices giving a reduction of power consumption. INPUT AND OUTPUT EQUIVALENT CIRCUIT ORDER CODES : M54HCT137F1R M74HCT137M1R M74HCT137B1R M74HCT137C1R PIN CONNECTIONS (top view) NC = No Internal Connection February 1993 1/12 M54/M74HCT137 T RUTH TABLE INPUTS GL X X L L L L L L L L H ENABLE G1 L X H H H H H H H H H G2 X H L L L L L L L L L C X X L L L L H H H H X SELECT B X X L L H H L L H H X A X X L H L H L H L H X Y0 H H L H H H H H H H Y1 H H H L H H H H H Y2 H H H H L H H H H OUTPUTS Y3 H H H H H L H H H Y4 H H H H H H L H H Y5 H H H H H H H L H Y6 H H H H H H H H L Y7 H H H H H H H H H H H H H H H L Outputs corresponding to stored address L: all others H LOGIC DIAGRAM 2/12 M54/M74HCT137 P IN DESCRIPTION PIN No 1, 2, 3 4 5 6 15, 14, 13, 12, 11, 10, 9, 7 8 16 SYMBOL A to C GL G2 G1 Y0 to Y7 GND VCC NAME AND FUNCTION Data Inputs Latch Enable Input (Active LOW) Data Enable Input (Active LOW) Data Enable Input (Active HIGH) Multiplexer Outputs Ground (0V) Positive Supply Voltage IEC LOGIC SYMBOLS ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO ICC or IGND PD Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Source Sink Current Per Output Pin DC VCC or Ground Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500 (*) -65 to +150 300 Unit V V V mA mA mA mA mW o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC 3/12 M54/M74HCT137 R ECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top tr, tf Supply Voltage Input Voltage Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time (VCC = 4.5 to 5.5V) Parameter Value 4.5 to 5.5 0 to VCC 0 to VCC -55 to +125 -40 to +85 0 to 500 Unit V V V o o C C ns DC SPECIFICATIONS Test Conditions Symbol Parameter VCC (V) 4.5 to 5.5 4.5 to 5.5 4.5 VI = IO=-20 µA VIH or IO=-4.0 mA V IL VI = IO= 20 µA VIH or IO= 4.0 mA V IL VI = VCC or GND VI = VCC or GND Per Input pin VI = 0.5V or V I = 2.4V Other Inputs at V CC or GND IO= 0 TA = 25 oC 54HC and 74HC Min. 2.0 Typ. Max. Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. 2.0 Max. Min. 2.0 Max. V Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage V IL 0.8 0.8 0.8 V V OH 4.4 4.18 4.5 4.31 0.0 0.17 0.1 0.26 ±0.1 4 2.0 4.4 4.13 0.1 0.33 ±1 40 2.9 4.4 4.10 0.1 V 0.4 ±1 80 3.0 µA µA mA V VOL Low Level Output Voltage 4.5 II ICC ∆ICC Input Leakage Current Quiescent Supply Current Additional worst case supply current 5.5 5.5 5.5 4/12 M54/M74HCT137 A C ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter VCC (V) 4.5 4.5 TA = 25 C 54HC and 74HC Min. Typ. Max. 8 17 15 27 o Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 19 34 22 41 ns Unit tTLH tTHL tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tW(L) Output Transition Time Propagation Delay Time (G1 - Y) Propagation Delay Time (G2 - Y) Propagation Delay Time (GL - Y) Propagation Delay Time (A, B, C - Y) Minimum Pulse Width (GL) Minimum Set-up Time (A, B, C - GL) Minimum Hold Time (A, B, C - GL) Input Capacitance Power Dissipation Capacitance ns 4.5 18 28 35 42 ns 4.5 25 39 49 59 ns 4.5 24 37 46 56 ns 4.5 8 15 19 22 ns ts 4.5 5 6 8 ns th 4.5 5 6 8 ns CIN CPD (*) 5 58 10 10 10 pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC 5/12 M54/M74HCT137 TEST CIRCUIT ICC (Opr.) INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST. TYPICAL APPLICATION 6/12 M54/M74HCT137 SWITCHING CHARACTERISTICS TEST WAVEFORM 7/12 M54/M74HCT137 Plastic DIP16 (0.25) MECHANICAL DATA mm MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP. MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 inch TYP. MAX. DIM. P001C 8/12 M54/M74HCT137 Ceramic DIP16/1 MECHANICAL DATA mm MIN. A B D E e3 F G H L M N P Q 7.8 2.29 0.4 1.17 0.22 0.51 0.38 17.78 2.79 0.55 1.52 0.31 1.27 10.3 8.05 5.08 0.307 0.090 0.016 0.046 0.009 0.020 3.3 0.015 0.700 0.110 0.022 0.060 0.012 0.050 0.406 0.317 0.200 TYP. MAX. 20 7 0.130 MIN. inch TYP. MAX. 0.787 0.276 DIM. P053D 9/12 M54/M74HCT137 SO16 (Narrow) MECHANICAL DATA DIM. MIN. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8° (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45° (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm TYP. MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.004 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010 P013H 10/12 M54/M74HCT137 PLCC20 MECHANICAL DATA mm MIN. A B D d1 d2 E e e3 F G M M1 1.27 1.14 7.37 1.27 5.08 0.38 0.101 0.050 0.045 9.78 8.89 4.2 2.54 0.56 8.38 0.290 0.050 0.200 0.015 0.004 TYP. MAX. 10.03 9.04 4.57 MIN. 0.385 0.350 0.165 0.100 0.022 0.330 inch TYP. MAX. 0.395 0.356 0.180 DIM. P027A 11/12 M54/M74HCT137 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. © 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 12/12