M74HCT273C1R

M 54HCT273 M74HCT273 OCTAL D TYPE FLIP FLOP WITH CLEAR . . . . . . . HIGH SPEED fMAX = 80 MHz (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) AT TA = 25 °C COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE IOH = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL PIN AND FUNCTION COMPATIBLE WITH 54/74LS273 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) DESCRIPTION The M54/74HCT273 is a high speed CMOS OCTAL D-TYPE FLIP FLOP WITH CLEAR fabricated in sili2 con gate C MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption. Information signals applied to D inputs are transferred to the Q outputs on the positive-going edge of the clock pulse. When the CLEAR input is held low, the Q output are in the low logic level independent of the other inputs. All inputs are equipped with protection circuits against static discharge and transient excess voltage. This integrated circuit has input and output characteristics that are fully compatible with 54/74 LSTTL logic families. M54/74HCT devices are de2 signed to directly interface HSC MOS systems with TTL and NMOS components. They are also plug in replacements for LSTTL devices giving a reduction of power consumption. All inputs are equipped with protection circuits against static discharge and transient excess voltage. INPUT AND OUTPUT EQUIVALENT CIRCUIT ORDER CODES : M54HCT273F1R M74HCT273M1R M74HCT273B1R M74HCT273C1R PIN CONNECTIONS (top view) NC = No Internal Connection February 1993 1/10 M54/M74HCT273 PIN DESCRIPTION PIN No 1 2, 5, 6, 9, 12, 15, 16, 19 3, 4, 7, 8, 13, 14, 17, 18 11 10 20 SYMBOL CLEAR Q0 to Q7 NAME AND FUNCTION Master Reset Input (Active LOW) Flip Flop Outputs IEC LOGIC SYMBOL D0 to D7 Data Inputs CLOCK GND V CC Clock Input (LOW to HIGH, Edge Triggered) Ground (0V) Positive Supply Voltage T RUTH TABLE CLEAR L H H H X: Don’t Care INPUTS CLOCK X D X L H X OUTPUS QA L L H Qn FUNCTION CLEAR NO CHANGE LOGIC DIAGRAM 2/10 M54/M74HCT273 A BSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO ICC or IGND PD Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Source Sink Current Per Output Pin DC VCC or Ground Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500 (*) -65 to +150 300 Unit V V V mA mA mA mA mW o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top tr, tf Parameter Supply Voltage Input Voltage Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time (VCC = 4.5 to 5.5V) Value 4.5 to 5.5 0 to VCC 0 to VCC -55 to +125 -40 to +85 0 to 500 Unit V V V C o C ns o 3/10 M54/M74HCT273 D C SPECIFICATIONS Test Conditions Symbol Parameter VCC (V) 4.5 to 5.5 4.5 to 5.5 4.5 VI = IO=-20 µA VIH or IO=-4.0 mA V IL VI = IO= 20 µA VIH or IO= 4.0 mA V IL VI = VCC or GND VI = VCC or GND Per Input pin VI = 0.5V or V I = 2.4V Other Inputs at V CC or GND IO= 0 4.4 4.18 4.5 4.31 0.0 0.17 0.1 0.26 ±0.1 4 2.0 TA = 25 oC 54HC and 74HC Min. Typ. Max. 2.0 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 2.0 Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage V V IL 0.8 0.8 0.8 V V OH 4.4 4.13 0.1 0.33 ±1 40 2.9 4.4 4.10 0.1 V 0.4 ±1 80 3.0 µA µA mA V VOL Low Level Output Voltage 4.5 II ICC ∆ICC Input Leakage Current Quiescent Supply Current Additional worst case supply current 5.5 5.5 5.5 4/10 M54/M74HCT273 A C ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter VCC (V) 4.5 4.5 TA = 25 oC 54HC and 74HC Min. Typ. Max. 9 15 19 30 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 19 22 38 45 Unit tTLH tTHL tPLH tPHL tPLH tPHL fMAX CIN CPD (*) Output Transition Time Propagation Delay Time (CLOCK - Q) Propagation Delay Time (CLEAR - Q) Maximum Clock Frequency Input Capacitance Power Dissipation Capacitance ns ns 4.5 22 32 40 48 ns 4.5 30 71 5 29 10 24 10 10 MHz pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC/8 (per Flip FLop), and the total CPD when n pcs of Flip Flop operate can be gained by the following equations: CPD (total) = 32 + 11 x n SWITCHING CHARACTERISTICS TEST WAVEFORM TEST CIRCUIT ICC (Opr.) 5/10 M54/M74HCT273 Plastic DIP20 (0.25) MECHANICAL DATA mm MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.34 8.5 2.54 22.86 7.1 3.93 0.130 0.053 0.254 1.39 0.45 0.25 25.4 0.335 0.100 0.900 0.280 0.155 1.65 TYP. MAX. MIN. 0.010 0.055 0.018 0.010 1.000 0.065 inch TYP. MAX. DIM. P001J 6/10 M54/M74HCT273 Ceramic DIP20 MECHANICAL DATA mm MIN. A B D E e3 F G I L M N1 P Q 7.9 2.29 0.4 1.27 0.22 0.51 0.5 22.86 2.79 0.55 1.52 0.31 1.27 0.090 0.016 0.050 0.009 0.020 3.3 1.78 0.020 0.900 0.110 0.022 0.060 0.012 0.050 TYP. MAX. 25 7.8 0.130 0.070 MIN. inch TYP. MAX. 0.984 0.307 DIM. 4° (min.), 15° (max.) 8.13 5.71 0.311 0.320 0.225 P057H 7/10 M54/M74HCT273 SO20 MECHANICAL DATA DIM. MIN. A a1 a2 b b1 C c1 D E e e3 F L M S 7.40 0.50 12.60 10.00 1.27 11.43 7.60 1.27 0.75 8° (max.) 0.291 0.19 13.00 10.65 0.35 0.23 0.50 45° (typ.) 0.496 0.393 0.050 0.450 0.299 0.050 0.029 0.512 0.419 0.10 mm TYP. MAX. 2.65 0.20 2.45 0.49 0.32 0.013 0.009 0.020 0.004 MIN. inch TYP. MAX. 0.104 0.007 0.096 0.019 0.012 P013L 8/10 M54/M74HCT273 PLCC20 MECHANICAL DATA mm MIN. A B D d1 d2 E e e3 F G M M1 1.27 1.14 7.37 1.27 5.08 0.38 0.101 0.050 0.045 9.78 8.89 4.2 2.54 0.56 8.38 0.290 0.050 0.200 0.015 0.004 TYP. MAX. 10.03 9.04 4.57 MIN. 0.385 0.350 0.165 0.100 0.022 0.330 inch TYP. MAX. 0.395 0.356 0.180 DIM. P027A 9/10 M54/M74HCT273 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. © 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 10/10