M74HCT688B1R

M 54HCT688 M74HCT688 8 BIT EQUALITY COMPARATOR . . . . . . . HIGH SPEED tPD = 17 ns (TYP.) AT VCC = 5 V LOW POWER DISSIPATION ICC = 4 µA (MAX.) AT TA = 25 °C COMPATIBLE WITH TTL OUTPUTS VIH = 2V (MIN.) VIL = 0.8V (MAX) OUTPUT DRIVE CAPABILITY 10 LSTTL LOADS SYMMETRICAL OUTPUT IMPEDANCE |IOH| = IOL = 4 mA (MIN.) BALANCED PROPAGATION DELAYS tPLH = tPHL PIN AND FUNCTION COMPATIBLE WITH 54/74LS688 B1R (Plastic Package) F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) ORDER CODES : M54HCT688F1R M74HCT688M1R M74HCT688B1R M74HCT688C1R PIN CONNECTIONS (top view) DESCRIPTION The M54/74HCT688 utilizes silicon gate C2MOS technology to achieve operating speeds equivalent to LSTTL devices. Along with the low power dissipation and high noise immunity of standard C2MOS integrated circuit, it possesses the driving capability of 10 LSTTL load. The M54/74HCT688 compares bit for bit two 8-bit words applied on inputs P0 - P7 and inputs Q0 - Q7 and indicates whether or not they are equal. A single active low enable is provided to facilitate cascading several packages to enable comparison of words greater than 8 bits. This integrated circuit has input and output characteristics that are fully compatible with 54/74 LSTTL logic families. M54/74HCT devices are 2 designed to directly interface HSC MOS systems with TTL and NMOS components. They are also plug in replacements for LSTTL devices giving a reduction of power consumption. All inputs are equipped with protection circuit against static discharge and transient excess voltage. February 1993 NC = No Internal Connection 1/10 M54/M74HCT688 I NPUT AND OUTPUT EQUIVALENT CIRCUIT TRUTH TABLE INPUT P, Q P=Q P≠Q X X: DON’T CARE OUTPUT G L L H P=Q L H H LOGIC DIAGRAM 2/10 M54/M74HCT688 P IN DESCRIPTION PIN No 1 2, 4, 6, 8, 11, 13, 15, 17 3, 5, 7, 9, 12, 14, 16, 18 19 10 20 SYMBOL G P0 to P7 NAME AND FUNCTION Enable Input (Active LOW) Word Inputs IEC LOGIC SYMBOL Q0 to Q7 Word Outputs P=Q GND V CC Equal to Output Ground (0V) Positive Supply Voltage ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO ICC or IGND PD Tstg TL Parameter Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Source Sink Current Per Output Pin DC VCC or Ground Current Power Dissipation Storage Temperature Lead Temperature (10 sec) Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500 (*) -65 to +150 300 Unit V V V mA mA mA mA mW o o C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top tr, tf Parameter Supply Voltage Input Voltage Output Voltage Operating Temperature: M54HC Series M74HC Series Input Rise and Fall Time (VCC = 4.5 to 5.5V) Value 4.5 to 5.5 0 to VCC 0 to VCC -55 to +125 -40 to +85 0 to 500 Unit V V V C o C o ns 3/10 M54/M74HCT688 D C SPECIFICATIONS Test Conditions Symbol Parameter VCC (V) 4.5 to 5.5 4.5 to 5.5 4.5 VI = IO=-20 µA VIH or IO=-4.0 mA V IL VI = IO= 20 µA VIH or IO= 4.0 mA V IL VI = VCC or GND VI = VCC or GND Per Input pin VI = 0.5V or V I = 2.4V Other Inputs at V CC or GND 4.4 4.18 4.5 4.31 0.0 0.17 0.1 0.26 ±0.1 4 2.0 TA = 25 oC 54HC and 74HC Min. Typ. Max. 2.0 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 2.0 2.0 Unit VIH High Level Input Voltage Low Level Input Voltage High Level Output Voltage V V IL 0.8 0.8 0.8 V V OH 4.4 4.13 0.1 0.33 ±1 40 2.9 4.4 4.10 0.1 V 0.4 ±1 80 3.0 µA µA mA V VOL Low Level Output Voltage 4.5 II ICC ∆ICC Input Leakage Current Quiescent Supply Current Additional worst case supply current 5.5 5.5 5.5 4/10 M54/M74HCT688 A C ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns) Test Conditions Symbol Parameter VCC (V) 4.5 4.5 TA = 25 oC 54HC and 74HC Min. Typ. Max. 8 21 15 32 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 19 40 22 48 ns 4.5 15 23 29 35 ns 5 32 10 10 10 pF pF Unit tTLH tTHL tPLH tPHL tPLH tPHL CIN CPD (*) Output Transition Time Propagation Delay Time (Pn, Qn - P = Q) Propagation Delay Time (G - P = Q) Input Capacitance Power Dissipation Capacitance ns (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD • VCC • fIN + ICC SWITCHING CHARACTERISTICS TEST WAVEFORM TEST CIRCUIT ICC (Opr.) INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST. 5/10 M54/M74HCT688 Plastic DIP20 (0.25) MECHANICAL DATA mm MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.34 8.5 2.54 22.86 7.1 3.93 0.130 0.053 0.254 1.39 0.45 0.25 25.4 0.335 0.100 0.900 0.280 0.155 1.65 TYP. MAX. MIN. 0.010 0.055 0.018 0.010 1.000 0.065 inch TYP. MAX. DIM. P001J 6/10 M54/M74HCT688 Ceramic DIP20 MECHANICAL DATA mm MIN. A B D E e3 F G I L M N1 P Q 7.9 2.29 0.4 1.27 0.22 0.51 0.5 22.86 2.79 0.55 1.52 0.31 1.27 0.090 0.016 0.050 0.009 0.020 3.3 1.78 0.020 0.900 0.110 0.022 0.060 0.012 0.050 TYP. MAX. 25 7.8 0.130 0.070 MIN. inch TYP. MAX. 0.984 0.307 DIM. 4° (min.), 15° (max.) 8.13 5.71 0.311 0.320 0.225 P057H 7/10 M54/M74HCT688 SO20 MECHANICAL DATA DIM. MIN. A a1 a2 b b1 C c1 D E e e3 F L M S 7.40 0.50 12.60 10.00 1.27 11.43 7.60 1.27 0.75 8° (max.) 0.291 0.19 13.00 10.65 0.35 0.23 0.50 45° (typ.) 0.496 0.393 0.050 0.450 0.299 0.050 0.029 0.512 0.419 0.10 mm TYP. MAX. 2.65 0.20 2.45 0.49 0.32 0.013 0.009 0.020 0.004 MIN. inch TYP. MAX. 0.104 0.007 0.096 0.019 0.012 P013L 8/10 M54/M74HCT688 PLCC20 MECHANICAL DATA mm MIN. A B D d1 d2 E e e3 F G M M1 1.27 1.14 7.37 1.27 5.08 0.38 0.101 0.050 0.045 9.78 8.89 4.2 2.54 0.56 8.38 0.290 0.050 0.200 0.015 0.004 TYP. MAX. 10.03 9.04 4.57 MIN. 0.385 0.350 0.165 0.100 0.022 0.330 inch TYP. MAX. 0.395 0.356 0.180 DIM. P027A 9/10 M54/M74HCT688 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. © 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 10/10