MC33174DT

MC33174 - MC35174 LOW POWER QUAD BIPOLAR OPERATIONAL AMPLIFIERS ■ GOOD CONSUMPTION/SPEED RATIO : ONLY 200µA FOR 2.1MHz, 2Vµs ■ SINGLE (OR DUAL) SUPPLY OPERATION FROM +4V TO +44V (±2V TO ±22V) ■ WIDE INPUT COMMON MODE MODE VOLTAGE RANGE INCLUDING VCC- N DIP14 (Plastic Package) ■ LOW LEVEL OUTPUT VOLTAGE CLOSE TO VCC- : 100mV TYPICAL ■ PIN TO PIN COMPATIBLE WITH STANDARD QUAD OP-AMPs DESCRIPTION The MC3x174 series are quad bipolar operational amplifier offering both low consumption (200µA) and good speed (2.1MHz, 2V/µs). Moreover the Input Common Mode Range extends down to the lower supply rail, allowing single supply operation from +4V to +44V. D SO14 (Plastic Micropackage) PIN CONNECTIONS (top view) ORDER CODE Output 1 1 Part Number Temperature Range MC33174 -40°C, +105°C MC35174 -55°C, +125°C Example : MC33174N Package N • • 14 Output 4 Inverting Input 1 2 - - 13 Inverting Input 4 D Non-inverting Input 1 3 + + 12 Non-inverting Input 4 • • VCC + 4 11 VCC - Non-inverting Input 2 5 + + 10 Non-inverting Input 3 Inverting Input 2 6 - - 9 Inverting Input 3 8 Output 3 Output 2 7 N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT)) April 2002 1/5 MC33174-MC35174 SCHEMATIC DIAGRAM (for 1/4 MC33174) VCC + R5 R4 T7 T8 R6 T10 T9 T1 R7 T13 T12 T11 R8 T25 R3 T16 T15 T6 Input - Input + T24 T26 T17 R13 T14 Output R12 C T22 T5 R14 T13 T2 T21 T19 T28 T27 T20 T3 T29 T4 T23 R2 R1 R10 R9 R11 T30 R15 T31 VCC - MAXIMUM RATINGS Symbol Value Unit ±22 V VCC Supply Voltage Vid Differential Input Voltage see note 1) V Vi Input Voltage Output Short Circuit Duration Operating Free-Air Temperature range see note 1 Indefinite -40 to 105 -55 to 125 V s Toper 1. Parameter MC33174 MC35174 °C Tj Junction Temperature 150 °C Tstg Storage Temperature -65 to 150 °C Value Unit ±2 to ±22 V Either or both input voltages must not exceed the magnitude of Vcc. OPERATING CONDITIONS Symbol VCC 2/5 Parameter Supply Voltage MC33174-MC35174 ELECTRICAL CHARACTERISTICS VCC+ = +15V, VCC- = -15V, R L connected to Ground, Tamb = 25°C (unless otherwise specified) Symbol Vio Parameter Min. Input Offset Voltage VCC+ = +15V, VCC- = -15V, Vic = 0V VCC+ = 5V, VCC- = 0V, Vic = 0V, Vo = 1.4V Typ. Max. 1 1 4.5 5 6.5 VCC = +15V, VCC = -15V, Vic = 0V, Tmin. ≤ Tamb ≤ Tmax. + DVio - Input Offset Voltage Drift 10 Iio Input Offset Current (Vic = 0V) Tmin. ≤ Tamb ≤ Tmax. 5 Iib Input Bias Current (Vic = 0V) Tmin. ≤ Tamb ≤ Tmax. Avd VOH Large Signal Voltage Gain (RL = 10kΩ, Vo = ±10V) Tmin. ≤ Tamb ≤ Tmax. High Level Output Voltage VCC+ = 5V, VCC- = 0V, RL = 10kΩ VCC+ = +15V, VCC- = -15V, RL = 10kΩ VCC = +15V, VCC = -15V, RL = 10kΩ, Tmin. ≤ Tamb ≤ Tmax + VOL - 20 50 25 100 3.5 13.6 13.3 4.2 14.2 Low Level Output Voltage VCC+ = 5V, VCC- = 0V, RL = 10kΩ 0.1 -14 VCC+ = +15V, VCC- = -15V, RL = 10kΩ VCC+ = +15V, VCC- = -15V, RL = 10kΩ, Tmin. ≤ Tamb ≤ Tmax Isc Output Short Circuit Current (Vid = ±1V, Vo = 0V) Source Sink 3 15 Unit mV µV/°C 20 40 nA 100 200 nA V/mV V 0.15 -13.6 -13.3 6 27 V mA VCC- to (VCC+ - 1.8) Vicm Input Common Mode Voltage Range Tmin. ≤ Tamb ≤ Tmax CMR Common-mode Rejection Ratio (Vic = Vicm min.) 80 100 dB SVR Supply Voltage Rejection Ratio (VCC = ±5 to ±15V) 80 100 dB ICC V VCC- to (VCC+ - 2.2) Supply Current VCC+ = 5V, VCC- = 0V, no load 200 220 VCC+ = +15V, VCC- = -15V, no load VCC+ = +15V, VCC- = -15V, no load, Tmin. ≤ Tamb ≤ Tmax SR GBP 250 250 300 µA Slew Rate (Vi = ±10V, RL = 10kΩ, CL = 100pF) 1.6 2 V/µs Gain Bandwidth Product RL = 10kΩ, CL = 100pF, f = 100kHz 1.4 2.1 MHz φm Phase Margin (RL = 10kΩ, CL = 100pF) 45 Degrees en Equivalent Input Noise Voltage (f = 1kHz) 29 nV -----------Hz 0.05 % 120 dB THD Total Harmonic Distortion VO1/VO2 Channel Separation 3/5 MC33174-MC35174 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Millimeters Inches Dimensions Min. a1 B b b1 D E e e3 F i L Z 4/5 Typ. 0.51 1.39 Max. Min. 1.65 0.020 0.055 0.5 0.25 Typ. 0.065 0.020 0.010 20 0.787 8.5 2.54 15.24 0.335 0.100 0.600 7.1 5.1 0.280 0.201 3.3 1.27 Max. 0.130 2.54 0.050 0.100 MC33174-MC35174 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO) G c1 s e3 b1 e a1 b A a2 C L E D M 8 1 7 F 14 Millimeters Inches Dimensions Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S Typ. Max. Min. 1.75 0.2 1.6 0.46 0.25 0.1 0.35 0.19 Typ. 0.069 0.008 0.063 0.018 0.010 0.004 0.014 0.007 0.5 Max. 0.020 45° (typ.) 8.55 5.8 8.75 6.2 0.336 0.228 1.27 7.62 3.8 4.6 0.5 0.344 0.244 0.050 0.300 4.0 5.3 1.27 0.68 0.150 0.181 0.020 0.157 0.208 0.050 0.027 8° (max.) Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK. Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States © http://www.st.com 5/5