P011xx
Sensitive high immunity SCRs up to 0.8 A
Features
A
■
IT(RMS) up to 0.8 A
■
VDRM/VRRM 400 and 600 V
■
IGT from 0.5 to 25 µA
G
K
Description
A
Thanks to highly sensitive triggering levels, the
P011xx SCR series is suitable for all applications
where available gate current is limited, such as
ground fault circuit interruptors, pilot circuits in
solid state relays, standby mode power supplies,
smoke and alarm detectors.
KA
K
G
G
A
SOT-223
(P011xxN)
TO-92
(P011xxA)
Available in through-hole or surface-mount
packages, the voltage capability of this series has
been upgraded since its introduction and is now
available up to 600 V.
Table 1.
Device summary
Voltage
Sensitivity
Order code
Package
400 V
600 V
Min.
Max.
P0111DA 1AA3
X
4 µA
25 µA
TO-92
P0111DA 5AL3
X
4 µA
25 µA
TO-92
P0111DN 5AA4
X
4 µA
25 µA
SOT-223
P0111MA 1AA3
X
4 µA
25 µA
TO-92
P0111MA2AL3(1)
X
4 µA
25 µA
TO-92
P0111MN 5AA4
X
4 µA
25 µA
SOT-223
P0115DA 1AA3
X
15 µA
50 µA
TO-92
P0115DA 5AL3
X
15 µA
50 µA
TO-92
P0118DA 1AA3
X
0.5 µA
5 µA
TO-92
P0118DA 5AL3
X
0.5 µA
5 µA
TO-92
P0118DN 5AA4
X
0.5 µA
5 µA
SOT-223
P0118MA 2AL3
X
0.5 µA
5 µA
TO-92
P0118MA 5AL3
X
0.5 µA
5 µA
TO-92
1. This order code has no space.
January 2009
Rev 1
1/9
www.st.com
9
Characteristics
P011xx
1
Characteristics
Table 2.
Absolute ratings (limiting values)
Symbol
IT(RMS)
Parameter
IT(AV)
Average on-state current (180° conduction angle)
ITSM
Non repetitive surge peak on-state current
I²t
TO-92
Tl = 55 °C
SOT-223
Tamb = 70 °C
TO-92
Tl = 55 °C
SOT-223
Tamb = 70 °C
RMS on-state current (180° conduction angle)
tp = 8.3 ms
tp = 10 ms
Unit
0.8
A
0.5
A
8
Tj = 25 °C
A
7
I²t Value for fusing
tp = 10 ms
Tj = 25 °C
0.24
A2 S
dI/dt
Critical rate of rise of on-state current
IG = 2 x IGT , tr ≤ 100 ns
F = 60 Hz
Tj = 125 °C
50
A/µs
IGM
Peak gate current
tp = 20 µs
Tj = 125 °C
1
A
Tj = 125 °C
0.1
W
- 40 to + 150
- 40 to + 125
°C
PG(AV)
Tstg
Tj
Table 3.
Average gate power dissipation
Storage junction temperature range
Operating junction temperature range
Electrical characteristics (Tj = 25 °C, unless otherwise specified)
Symbol
IGT
Test conditions
VD = 12 V
P0111
P0115
P0118
Min.
4
15
0.5
Max.
25
50
5
Unit
µA
RL = 140 Ω
VGT
0.8
V
Min.
0.1
V
Min.
8
V
VD = VDRM RL = 3.3 kΩ RGK = 1 kΩ
VRG
IRG = 10 µA
IH
IT = 50 mA
RGK = 1 kΩ
Max.
5
mA
IL
IG = 1 mA
RGK = 1 kΩ
Max.
6
mA
dV/dt
VD = 67 % VDRM
VTM
ITM = 1.6 A
Vt0
Rd
RGK = 1 kΩ
Tj = 125 °C
Max.
VGD
IDRM
IRRM
2/9
Value
Tj = 125 °C
Min.
Tj = 25 °C
Max.
1.95
V
Threshold voltage
Tj = 125 °C
Max.
0.95
V
Dynamic resistance
Tj = 125 °C
Max.
600
mΩ
tp = 380 µs
VDRM = VRRM = 400 V
RGK = 1 kΩ
VDRM = VRRM = 600 V
RGK = 1 kΩ
VDRM = VRRM
RGK = 1 kΩ
80
75
75
V/µs
1
Tj = 25 °C
Tj = 125 °C
Max.
10
100
µA
P011xx
Characteristics
Table 4.
Thermal resistance
Symbol
Parameter
Rth(j-a)
Junction to case (DC)
Rth(j-t)
Junction to tab (DC)
Rth(j-a)
Junction to ambient (DC)
Maximum
Unit
TO-92
80
°C/W
SOT-223
30
°C/W
TO-92
150
SOT-223
60
°C/W
S(1) = 5 cm2
1. S = Copper surface under tab.
Figure 1.
Maximum average power
Figure 2.
dissipation versus average on-state
current
P(W)
Average and DC on-state current
versus lead temperature
IT(AV)(A)
1.0
1.1
0.9
D.C. (SOT-223)
1.0
α = 180°
0.9
0.8
0.8
0.7
D.C. (TO-92)
0.7
0.6
0.6
0.5
α = 180° (SOT-223)
0.5
0.4
0.4
0.3
0.3
360°
0.2
α = 180° (TO-92)
0.2
0.1
IT(AV)(A)
0.0
0.1
Figure 3.
0.2
0.1
α
0.0
0.3
0.4
0.5
Tlead(°C)
0.0
0
0.6
Average and DC on-state current
versus ambient temperature
25
Figure 4.
50
75
100
125
Relative variation of thermal
impedance junction to ambient
versus pulse duration
K=[Zth(j-a)/Rth(j-a)]
IT(AV)(A)
1.00
1.2
1.1
Device mounted on FR4 with
recommended pad layout
D.C. (SOT-223)
1.0
0.9
0.8
TO-92
0.7
D.C. (TO-92)
0.6
0.10
α = 180° (SOT-223)
0.5
SOT-223
0.4
0.3
α = 180° (TO-92)
0.2
0.1
tp(s)
Tamb(°C)
0.0
0
25
50
75
0.01
100
125
1E-2
1E-1
1E+0
1E+1
1E+2
5E+2
3/9
Characteristics
Figure 5.
P011xx
Relative variation of gate trigger,
Figure 6.
holding and latching current versus
junction temperature
Relative variation of holding
current versus gate-cathode
resistance (typical values)
IH[RGK] / IH[RGK=1kΩ]
IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25°C]
20
6
Tj = 25°C
18
typical values
5
16
14
4
12
3
10
IGT
8
2
6
1
4
IH & IL
RGK = 1kΩ
Tj(°C)
2
RGK(kΩ)
0
-40
-20
Figure 7.
0
20
40
60
80
100
120
140
0
1E-2
1E-1
Relative variation of dV/dt immunity Figure 8.
versus gate-cathode resistance
(typical values).
1E+0
1E+1
Relative variation of dV/dt immunity
versus gate-cathode capacitance
(typical values)
dV/dt[CGK] / dV/dt[RGK=1kΩ]
dV/dt[RGK] / dV/dt[RGK=1kΩ]
10
10.0
VD = 0.67 x VDRM
Tj = 125°C
RGK = 1kΩ
Tj = 125°C
VD = 0.67 x VDRM
8
6
1.0
4
2
RGK(kΩ)
0.1
CGK(nF)
0
0
0.2
Figure 9.
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0
1
2
3
4
5
6
7
Surge peak on-state current versus Figure 10. Non-repetitive surge peak on-state
number of cycles
current and corresponding value
of I²t
ITSM(A), I2t (A2s)
ITSM(A)
100.0
8
Tj initial = 25°C
7
ITSM
tp=10ms
6
One cycle
sinusoidal pulse with
width tp < 10ms
10.0
5
Non repetitive
Tj initial=25°C
4
3
Repetitive
Tamb=25°C
1.0
2
I2t
1
Number of cycles
0
1
4/9
tp(ms)
10
100
0.1
1000
0.01
0.10
1.00
10.00
P011xx
Ordering information scheme
Figure 11. On-state characteristics (maximum Figure 12. Thermal resistance junction to
values)
ambient versus copper surface
under tab
ITM(A)
Rth(j-a)(°C/W)
1E+1
130
120
110
100
90
80
70
60
50
40
30
20
10
0
Tj max.:
Vt0=0.95V
Rd=600mΩ
1E+0
Tj=max
Tj=25°C
1E-1
VTM(V)
1E-2
0.5
2
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Epoxy printed circuit board FR4,
copper thickness: 35 µm
S(cm²)
0.0
4.5
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Ordering information scheme
Figure 13. Ordering information scheme
P
01 1x
x
x
Blank
xAxx
Sensitive SCR series
Current
01 up to 0.8 A
Sensitivity
11 = 4 to 25 µA
15 = 15 to 50 µA
18 = 0.5 to 5 µA
Voltage
D = 400 V
M = 600 V
Package
A = TO-92
N = SOT-223
Packing mode
1AA3 = Bulk
2AL3 = Ammopack
5AL3 = Tape and reel 13 inch
5AA4 = Tape and reel 7 inch
5/9
Package information
3
P011xx
Package information
●
Epoxy meets UL94, V0
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 5.
TO-92 dimensions
dimensions
Ref
Millimeters
Min
Typ
Max
Inches
Min
Typ
Max
A
a
B
A
1.35
B
C
4.70
C
F
6/9
D
E
0.053
0.185
2.54
0.100
D
4.40
0.173
E
12.70
0.500
F
3.70
0.146
a
0.50
0.019
P011xx
Package information
Table 6.
SOT-223 dimensions
Dimensions
Ref.
V
A
A1
c
Typ.
Inches
Max.
Min.
Typ.
1.80
A1
0.02
Max.
0.071
0.001
B
0.60
0.70
0.80 0.024 0.027 0.031
B1
B1
2.90
3.00
3.10 0.114 0.118 0.122
c
0.24
0.26
0.32 0.009 0.010 0.013
4
D
6.30
6.50
6.70 0.248 0.256 0.264
D
E
1
Min.
A
B
e1
H
Millimeters
2
3
e
e
2.3
0.090
e1
4.6
0.181
E
3.30
3.50
3.70 0.130 0.138 0.146
H
6.70
7.00
7.30 0.264 0.276 0.287
V
10° max
Figure 14. Footprint (dimensions in mm)
3.25
1.32
5.16
7.80
1.32
2.30
0.95
7/9
Ordering information
4
P011xx
Ordering information
Table 7.
Ordering information
Order code
Marking
Package
Weight
Base qty
Packing mode
P0111DA 1AA3
P0111 DA
TO-92
0.2 g
2500
BAG
P0111DA 5AL3
P0111 DA
TO-92
0.2 g
2000
Tape and reel 13 inch
P0111DN 5AA4
P1D
SOT-223
0.11 g
1000
Tape and reel 7 inch
P0111MA 1AA3
P0111 MA
TO-92
0.2 g
2500
Bag
P0111 MA
TO-92
0.2 g
2000
Ammopack
P0111MN 5AA4
P1M
SOT-223
0.11 g
1000
Tape and reel 7 inch
P0115DA 1AA3
P0115 DA
TO-92
0.2 g
2500
Bag
P0115DA 5AL3
P0115 DA
TO-92
0.2 g
2000
Tape and reel 13 inch
P0118DA 1AA3
P0118 DA
TO-92
0.2 g
2500
Bag
P0118DA 5AL3
P0118 DA
TO-92
0.2 g
2000
Tape and reel 13 inch
P0118DN 5AA4
P8D
SOT-223
0.11 g
1000
Tape and reel 7 inch
P0118MA 2AL3
P0118 MA
TO-92
0.2 g
2000
Ammopack
P0118MA 5AL3
P0118 MA
TO-92
0.2 g
2000
Tape and reel 13 inch
P0111MA2AL3
(1)
1. This order code has no space.
5
Revision history
Table 8.
8/9
Document revision history
Date
Revision
26-Jan-2009
1
Description of changes
First issue.
P011xx
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
9/9
很抱歉,暂时无法提供与“P0115DA1AA3”相匹配的价格&库存,您可以联系我们找货
免费人工找货