RHFL4913ESY1505V

RHFL4913XX15 - RHFL4913XX25 RHFL4913XX33 - RHFL4913XX50 Rad-hard positive fixed voltage regulator Features ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 2 and 3 A low dropout voltage Embedded overtemperature, overcurrent protections Adjustable current limitation Output overload monitoring/signalling Fixed 1.5 V, 2.5 V; 3.3 V; 5.0 V output voltages Inhibit (ON/OFF) TTL-compatible control Programmable output short-circuit current Remote sensing operation Rad-hard: tested up to 300 krad Mil Std 883E Method 1019.6 and low dose rate conditions Heavy ion, SEL, and SEU immune; able to sustain 2x1014 protons/cm2 and 2x1014 neutrons/cm2 TO-257 Flat-16 SMD.5 Available into various hermetic ceramic packages, it is specifically intended for space and harsh radiation environments. Input supply range is up to 12 V. RHFL4913 fixed is QML-V qualified, DSCC SMD are 5962F02534 / 02535 / 02536. Description The RHFL4913 fixed is a high performance Radhard positive voltage regulator family. Figure 1. Block diagram for package SMD.5 and TO-257 August 2008 Rev 8 1/19 www.st.com 19 Contents RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Contents 1 2 3 4 5 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1 5.2 5.3 5.4 5.5 5.6 5.7 Low pin count package limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SENSE pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Inhibit ON-OFF control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overtemperature protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 OCM pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Alternate to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6.1 Remote sensing operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7 Notes about Flat-16 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7.1 7.2 Radiation performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Die information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 9 10 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Diagram 1 Figure 2. Diagram Block diagram for package Flat-16 3/19 Pin configuration RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 2 Figure 3. Pin configuration Pin configuration (top view for Flat-16, bottom view for SMD.5) Flat-16 SMD.5 TO-257 Table 1. Pin description Pin name VO VI GND ISC OCM INHIBIT SENSE NC Flat-16 1, 2, 6, 7 3, 4, 5 13 8 10 14 16 9, 11, 12, 15 SMD.5 1 2 3 TO-257 3 1 2 4/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Maximum ratings 3 Table 2. Symbol VI IO Maximum ratings Absolute maximum ratings (1) Parameter DC input voltage, VI - VGROUND RHFL4913S, ESY Output current RHFL4913KP KP, S Versions PD TSTG TOP TJ ESD TC = 25°C power dissipation Storage temperature range Operating junction temperature range Junction temperature (2) Value 14 3 Unit V A 2 15 W 10 -65 to +150 -55 to +150 +150 Class 3 °C °C °C ESY Version Electrostatic discharge capability 1. Exceeding maximum ratings may damage the device. 2. Internally limited to about maximum +175 °C by thermal shutdown circuit. Table 3. Symbol RthJC TSOLD Thermal data Parameter Thermal resistance junction-case max. Maximum soldering temperature, 10 sec. Flat-16 8.3 TO-257 12.5 300 SMD.5 8.3 Unit °C/W °C 5/19 Electrical characteristics RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 4 Table 4. Symbol VI VO ISHORT VO VO VO VO ΔVO/ΔVI Electrical characteristics Electrical characteristics (TJ = 25 °C, VI = VO+2.5 V, CI = CO = 1 µF, unless otherwise specified) Parameter Operating input voltage Test conditions IO = 2 A (Flat-16) or 3A (SMD.5 & TO-257) -2 4.5 1.47 2.45 3.23 4.9 1.53 2.55 3.37 5.1 0.3 0.4 0.4 0.2 0.3 0.3 0.3 0.4 0.4 100 8 25 60 150 1 40 mA 100 mA Min. Typ. Max. 12 2 Unit V % A V V V V % % % % % % % % % mΩ Output voltage accuracy VI = VO+2.5V, IO = 5mA Output current limit (1) Adjustable by mask/external resistor Operating output voltage IO = 2 A, 1.5 V output voltage Operating output voltage IO = 2 A, 2.5 V output voltage Operating output voltage IO = 2 A, 3.3 V output voltage Operating output voltage IO = 2 A, 5.0 V output voltage VI = VO+2.5V to 12 V, IO = 5mA (+25°C) Line regulation VI = VO+2.5V to 12 V, IO = 5mA (-55°C) VI = VO+2.5V to 12 V, IO = 5mA (+125°C) VI = VO+2.5V, IO = 5mA to 400 mA (+25°C) VI = VO+2.5V, IO = 5mA to 400 mA (-55°C) ΔVO/ΔVO Load regulation VI = VO+2.5V, IO = 5mA to 400 mA (+125°C) VI = VO+2.5V, IO = 5mA to 1A (+25°C) VI = VO+2.5V, IO = 5mA to 1A (-55°C) VI = VO+2.5V, IO = 5mA to 1A (+125°C) ZOUT Output impedance IO = 100 mA DC and 20 mA rms VI = VO+2.5V, IO = 30mA, on mode VI = VO+2.5V, IO = 300mA, on mode VI = VO+2.5V, IO = 1A, on mode VI = VO+2.5V, IO = 3A, on mode (only for SMD.5 and TO-257) VI = VO+2V, VINH = 2.4V, off mode Iq Quiescent current Iq Quiescent current VI =VO+2.5V, IO=1A, TJ=+125°C, on mode VI =VO+2.5V, IO=1A, TJ=-55°C, on mode 6/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Table 4. Symbol Electrical characteristics Electrical characteristics (continued) (TJ = 25 °C, VI = VO+2.5 V, CI = CO = 1 µF, unless otherwise specified) Parameter Test conditions IO = 400mA, TJ = -55°C IO = 400mA, TJ = +25°C IO = 400mA, TJ = +125°C Min. Typ. 300 350 450 Max. 400 450 550 550 mV 650 800 750 950 0.8 2.4 f = 120Hz f = 33kHz 60 30 70 dB 40 15 0.38 on-off VI = VO+2.5V, VINH = 2.4 V, IO = 400 mA B= 10Hz to 100kHz, IO = 5mA to 2A off-on 40 20 100 µA V µs µs µVrms V V Unit Vd Dropout voltage IO = 1A, TJ = -55°C IO = 1A, TJ = +25°C IO = 1A, TJ = +125°C IO = 2A, TJ = +25°C IO = 2A, TJ = +125°C VINH(ON) Inhibit voltage VINH(OFF) Inhibit voltage SVR ISH VOCM tPLH tPHL eN Supply voltage rejection (1) IO = 5mA, TJ= -55 to 125°C IO = 5mA, TJ= -55 to 125°C VI = VO+2.5V ± 1V, IO = 5mA VINH = 5 V Sinked IOCM = 24 mA active low Shutdown input current OCM pin voltage Inhibit propagation delay (1) (1) Output noise voltage 1. This value is guaranteed by design. For each application it’s strongly recommended to comply with the maximum current limit of the package used. Figure 4. Application diagram for remote sensing operation 7/19 Device description RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 5 Device description The RHFL4913 fixed voltage contains a PNP type power element controlled by a signal resulting from amplified comparison between the internal temperature compensated bandgap cell and the fraction of the desired output voltage value. This fractional value is obtained from an internal-to-die resistor divider bridge set by STMicroelectronics. The device is protected by several functional blocks. 5.1 Low pin count package limitations Some functions (INHIBIT, OCM, SENSE) are not available due to lack of pins. Corresponding die pads are by default connected inside silicon. 5.2 SENSE pin The load voltage is applied by a Kelvin line connected to SENSE pin: Voltage feed-back comes from the internal divider resistor bridge. Therefore possible output voltages are set by manufacturer mask metal options. SENSE pin is not available in 3pin packages. 5.3 Inhibit ON-OFF control By setting INHIBIT pin TTL-high, the device switches off the output current and voltage. The device is ON when INHIBIT pin is set low. Since INHIBIT pin is internally pulled down, it can be left floating in case inhibit function is not utilized. INHIBIT pin is not available in 3pin packages. 5.4 Overtemperature protection A temperature detector internally monitors the power element junction temperature. The device goes OFF at approx. 175 °C, returning to ON mode when back to approx. 40 °C. It is worth noting that when the internal temperature detector reaches 175 °C, the active power element can be at 225 °C: device reliability cannot be granted in case of extensive operation under these conditions. 5.5 Overcurrent protection ISC pin. An internal non-fold back short-circuit limitation is set with ISHORT > 3.8 A (VO is 0 V). This value can be reduced by an external resistor connected between ISC pin and VI pin, with a typical value range of 10 kΩ to 200 kΩ. This adjustment feature is not available in 3 pin packages. To keep excellent VO regulation, it is necessary to set ISHORT 1.6 times greater than the maximum desired application IO. When IO reaches ISHORT – 300 mA, the current limiter overrules regulation and VO starts to drop and the OCM flag is risen. When no current limitation adjustment is required, ISC pin must be left unbiased (as it is in 3 pin packages). 8/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Device description 5.6 OCM pin Goes low when current limiter starts to be active, otherwise VOCM = VI. It is bufferized and can sink 10 mA. OCM pin is internally pulled-up by a 5 kΩ resistor. Not available in 3 pin packages. 5.7 Alternate to RHFL4913 fixed (& custom) voltages replace all 3-terminal industry devices, providing essential benefits - Lower drop-out - High radiation performance - Better SVR - Saving the high stability external setting resistors. 9/19 Application information RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 6 Application information The RHFL4913 fixed voltage is functional as soon as VI-VO voltage difference is slightly above the power element saturation voltage. A minimum 0.5 mA IO ensures perfect “noload” regulation. All available VI pins must always be externally interconnected, same thing for all available VO pins, otherwise device stability and reliability cannot be granted. All NC pins can be connected to ground. The INHIBIT function switches off the output current in an electronic way, that is very quickly. According to Lenz’s Law, external circuitry reacts with –LdI/dt terms which can be of high amplitude in case some series-inductance exists. The effect would be a large transient voltage developed on both device terminals. It is necessary to protect the device with Schottky diodes preventing negative voltage excursions. In the worst case, a 14 V Zener diode shall protect the device input. The device has been designed for high stability and low drop out operation: minimum 1 µF input and output tantalum capacitors are therefore mandatory. Capacitor ESR range is from 0.5 Ω to over 20 Ω. Such range turns out to be useful when ESR increases at low temperature. When large transient currents are expected, larger value capacitors are necessary. In case of high current operation with expected short-circuit events, caution must be considered relatively to capacitors. They must be connected as close as possible to device terminals. As some tantalum capacitors may permanently fail when submitted to high charge-up surge currents, it is recommended to decouple them with 470 nF polyester capacitors. Being RHFL4913 fixed voltage manufactured with very high speed bipolar technology 6 GHz fT transistors), the PCB lay-out must be performed with extreme care, very low inductance, low mutually coupling lines, otherwise high frequency parasitic signals may be picked-up by the device resulting into self-oscillation. User’s benefit is a SVR performance extended to far higher frequencies. 6.1 Remote sensing operation In case the load is located far from the regulator, it is recommended to comply with the scheme below. To obtain the best regulation, it is in addition essential to care about: – The wire connecting R2 to the load end must not be crossed by the load current (Kelvin sense). The noise captured by the wires between the load and the chip could bring a noisy output voltage. In case this happens, it is recommended that shielded cables are used for these connections. The external wrap must be used for connecting the ground of the chip with the load ground. It is also recommended to place 1 µF tantalum capacitors between output and ground close to the device and another next to the load. 10/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Notes about Flat-16 package 7 Notes about Flat-16 package The bottom of package is metallized to allow user to directly solder the voltage regulator to the equipment heater, in order to optimize heat removal performance. 7.1 Radiation performances The RHFL4913F has been tested against: 300krad TID ELDERS in accordance with Mil1019.6, bipolar section: post radiation parameters are within datasheet pre-rad limits. Submitted to 200MeV Iodine ions of 60.4MeV/cm2/mg LET up to 1exp(+7) ions / cm2, no SEL event has been detected. 7.2 Die information RHFL4913 fixed is also available in die form. Space dice are electrically tested by STMicroelectronics in such a way that, when mounted in proper thermal and electrical substrate, they provide full compliance with equivalent packaged product. - Max die dimensions: 2.794 mm by 3.861 mm or 110 mils by 152 mils - Die thickness: 357 µm +/- 50 µm - Pad size: 184 µm by 184 µm - Metallization: Aluminum 4% silicon alloy - Die backside: Bare silicon - Die backside potential: Ground Figure 5. Die size (*) Die SENSE pad is active in RHFL4913 fixed die. It shall not be left unbonded. It should be bonded to VO pin. (**) Die adjust pad is available in the die lay-out but is not electrically connected to the IC. It shall be left unconnected during hybrid bonding. 11/19 Package mechanical data RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 8 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 12/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Package mechanical data Flat-16 (MIL-STD-1835) mechanical data mm. Dim. Min. A b c D E E2 E3 e L Q S1 0.66 0.13 0.76 1.27 6.72 1.14 0.026 0.005 2.16 0.43 0.13 9.91 6.91 4.32 0.030 0.050 0.265 0.045 Typ. Max. 2.72 Min. 0.085 0.017 0.005 0.390 0.272 0.170 Typ. Max. 0.107 inch. e b c L E3 16 9 E E2 1 8 E3 L S1 D Q A 7450901A 13/19 Package mechanical data RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 SMD.5 mechanical data Dim. A A1 b b1 b2 b3 D D1 E e mm. Min. 2.84 0.25 7.13 5.58 2.28 2.92 10.03 0.76 7.39 7.52 1.91 7.64 Typ. 3.00 0.38 7.26 5.72 2.41 3.05 10.16 Max. 3.15 0.51 7.39 5.84 2.54 3.18 10.28 Min. 0.112 0.010 0.281 0.220 0.090 0.115 0.395 0.030 0.291 0.296 0.075 0.301 inch. Typ. 0.118 0.015 0.286 0.225 0.095 0.120 0.400 Max. 0.124 0.020 0.291 0.230 0.100 0.125 0.405 7386434B 14/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Package mechanical data TO-257 mechanical data Dim. A B C D E F G H I J K L M N R 1.65 15.2 2.29 0.71 0.065 3.56 4.7 1.02 3.68 13.51 5.26 0.76 3.05 2.54 16.5 0.598 0.090 0.028 3.81 0.140 mm. Min. Typ. 10.54 10.54 16.64 5.33 0.185 0.40 0.145 0.532 0.207 0.030 0.120 0.100 0.650 0.150 Max. Min. inch. Typ. 0.415 0.415 0.655 0.210 Max. 0117268C 15/19 Ordering information RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 9 Table 5. DIE Ordering information Order codes Flat-16 RHFL4913KP15-01V RHFL4913KP15-02V RHFL4913KP151 RHFL4913KP152 SMD.5 RHFL4913S15-03V RHFL4913S15-04V RHFL4913S151 RHFL4913S152 TO-257 RHFL4913ESY1505V RHFL4913ESY1506V RHFL4913ESY151 RHFL4913ESY152 Terminal finish GOLD SOLDER GOLD GOLD NA NA Out. volt. 1.5 V 1.5 V 1.5 V 1.5 V 1.5 V 1.5 V 2.5 V 2.5 V 2.5 V 2.5 V 2.5 V 2.5 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V 5.0 V Q.ty level EM1 EM1=EM2 +48h B.I. L491315DIE2V L491315DIE2S RHFL4913KP25-01V RHFL4913KP25-02V RHFL4913KP251 RHFL4913KP252 L491325DIE2V L491325DIE2S RHFL4913KP33-01V RHFL4913KP33-02V RHFL4913KP331 RHFL4913KP332 L491333DIE2V L491333DIE2S RHFL4913KP50-01V RHFL4913KP50-02V RHFL4913KP501 RHFL4913KP502 L491350DIE2V L491350DIE2S RHFL4913S50-03V RHFL4913S50-04V RHFL4913S501 RHFL4913S502 RHFL4913ESY5005V RHFL4913ESY5006V RHFL4913ESY501 RHFL4913ESY502 RHFL4913S33-03V RHFL4913S33-04V RHFL4913S331 RHFL4913S332 RHFL4913ESY3305V RHFL4913ESY3306V RHFL4913ESY331 RHFL4913ESY332 RHFL4913S25-03V RHFL4913S25-04V RHFL4913S251 RHFL4913S252 RHFL4913ESY2505V RHFL4913ESY2506V RHFL4913ESY251 RHFL4913ESY252 EM1 QML-V QML-V EM1 EM1=EM2 +48h B.I. QML-V EM1 QML-V QML-V EM1 EM1=EM2 +48h B.I. QML-V EM1 QML-V QML-V EM1 EM1=EM2 +48h B.I. QML-V EM1 GOLD SOLDER GOLD GOLD NA NA GOLD SOLDER GOLD GOLD NA NA GOLD SOLDER GOLD GOLD NA NA 16/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Table 6. Part number - SMD equivalent ST part number RHFL4913KP15-02V RHFL4913KP25-01V RHFL4913KP25-02V RHFL4913KP33-01V RHFL4913KP33-02V RHFL4913KP50-01V RHFL4913KP50-02V RHFL4913S25-03V RHFL4913S25-04V RHFL4913S33-03V RHFL4913S33-04V Ordering information SMD part number 5962F0253401VXC 5962F0253401VXA 5962F0253501VXC 5962F0253501VXA 5962F0253601VXC 5962F0253601VXA 5962F0253402VYC 5962F0253402VYA 5962F0253502VYC 5962F0253502VYA RHFL4913S50-03V RHFL4913S50-04V RHFL4913ESY2505V RHFL4913ESY2506V RHFL4913ESY3305V RHFL4913ESY3306V RHFL4913ESY5005V RHFL4913ESY5006V L491325DIE2V L491333DIE2V L491350DIE2V 5962F0253602VYC 5962F0253602VYA 5962F0253402VZC 5962F0253402VZA 5962F0253502VZC 5962F0253502VZA 5962F0253602VZC 5962F0253602VZA 5962F0253402V9A 5962F0253502V9A 5962F0253602V9A Note: 3 V version is available on request. Table 7. Environmental characteristics Parameter Conditions -55°C to +125°C From 0 krad to 300 krad at 0.55 rad/s From 0 krad to 300 krad, Mil Std 883E Method 1019.6 Value 40 8 6 Unit ppm/°C ppm/krad ppm/krad Output voltage thermal drift Output voltage radiation drift Output voltage radiation drift 17/19 Revision history RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 10 Table 8. Date Revision history Document revision history Revision 4 5 6 7 8 Changes Mistake in pin description SMD.5 on table 3. New order codes added - tables 4 and 5. The features, tables 4, 5 and the figures 1, 2 updated. Modified: PD on table 1, the RthJC for TO-257 on table 2 and the tables 6 and 7, added DIE information. Added new output 1.5 V, modified: Table 4 on page 6, Table 5 on page 16 and Table 6 on page 17. 05-May-2004 28-Oct-2004 27-May-2005 08-Jun-2005 26-Aug-2008 18/19 RHFL4913XX15 - RHFLXX25 - RHFLXX33 - RHFLXX50 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 19/19