RHFL4913KPA-01V

RHFL4913A Rad-hard adjustable positive voltage regulator Features ■ ■ ■ ■ ■ ■ ■ ■ ■ 3 A low dropout voltage Embedded overtemperature and overcurrent protection Adjustable overcurrent limitation Output overload monitoring/signalling Adjustable output voltage Inhibit (ON/OFF) TTL-compatible control Programmable output short-circuit current Remote sensing operation Rad-hard: guaranteed up to 300 krad Mil Std 883E Method 1019.6 high dose rate and 0.01 rad/s in ELDRS conditions Heavy ion, SEL immune FLAT-16 SMD5C: 5-connection SMD ■ Description The RHFL4913A high-performance adjustable positive voltage regulator provides exceptional radiation performance. It is tested in accordance with Mil Std 883E Method 1019.6, in ELDRS conditions. The device is available in the FLAT-16 and the new SMD5C hermetic ceramic package, and the QML-V die is specifically designed for space and harsh radiation environments. It operates with an input supply of up to 12 volts. The RHFL4913A is QML-V qualified, DSCC SMD #5962F02524. January 2010 Doc ID 10005 Rev 11 1/20 www.st.com 20 Contents RHFL4913A Contents 1 2 3 4 5 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1 5.2 5.3 5.4 5.5 5.6 ADJ pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Inhibit ON-OFF control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overtemperature protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Overcurrent protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 OCM pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Alternatives to the RHFL4913A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6.1 6.2 6.3 Notes on the 16-pin hermetic package . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Remote sensing operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 FPGA power supply lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 7 Die information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 7.1 Die bonding pad locations and electrical functions . . . . . . . . . . . . . . . . . 13 8 9 10 11 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 Doc ID 10005 Rev 11 RHFL4913A Diagram 1 Figure 1. Diagram Block diagram Doc ID 10005 Rev 11 3/20 Pin configuration RHFL4913A 2 Figure 2. Pin configuration Pin configuration (top view for FLAT-16, bottom view for SMD5C) FLAT-16 SMD5C Table 1. Pin description Pin name VO VI GND ISC OCM INHIBIT ADJ NC FLAT-16 1, 2, 6, 7 3, 4, 5 13 8 10 14 15 9, 11, 12, 16 3 2 SMD5C 1 4 5 4/20 Doc ID 10005 Rev 11 RHFL4913A Maximum ratings 3 Table 2. Symbol VI VO IO IO PD TSTG TOP ESD Maximum ratings Recommended maximum operating ratings (1) Parameter DC input voltage, VI - VGROUND DC output voltage range Output current, RHFL4913KPA Output current, RHFL4913SCA TC = 25 °C power dissipation Storage temperature range Operating junction temperature range Electrostatic discharge capability Value 12 1.23 to 9 2 A 3 15 -65 to +150 -55 to +150 Class 3 W °C °C Unit V V 1. Exceeding maximum ratings may damage the device. Table 3. Symbol RthJC TSOLD Thermal data Parameter Thermal resistance junction-case, FLAT-16 and SMD5C Maximum soldering temperature, 10 sec. Value 8.3 300 Unit °C/W °C Doc ID 10005 Rev 11 5/20 Electrical characteristics RHFL4913A 4 Electrical characteristics TJ = 25 °C, VI = VO + 2.5 V, CI = CO = 1 µF, unless otherwise specified. Table 4. Symbol VI VO ISHORT Electrical characteristics Parameter Test conditions Min. 3 1.19 8.7 1 4.5 0.35 0.4 0.4 0.3 0.5 0.5 % 0.5 0.6 0.6 100 6 8 mA 25 60 1 14 40 100 mA 8 20 40 mΩ % Typ. Max. 12 1.27 9.3 Unit V V V A Operating input voltage IO = 1 A, TJ = -55 to 125°C Operating output voltage Output current limit (1) IO = 1 A and or 2, VO = 1.23 V IO = 1 A and or 2, VO = 9 V Adjustable by mask/external resistor VI = VO+2.5 V to 12 V, IO = 5 mA, TJ = +25°C ΔVO/ΔVI Line regulation VI = VO+2.5 V to 12 V, IO = 5 mA, TJ = -55°C VI = VO+2.5 V to 12 V, IO = 5 mA, TJ = +125°C VI = VO+2.5 V, IO = 5 to 400 mA, TJ = +25°C VI = VO+2.5 V, IO = 5 to 400 mA, TJ = -55°C ΔVO/ΔVO Load regulation VI = VO+2.5 V, IO = 5 to 400 mA, TJ = +125°C VI = VO+2.5 V, IO = 5 mA to 1 A, TJ = +25°C VI = VO+2.5 V, IO = 5 mA to 1A, TJ = -55°C VI = VO+2.5 V, IO = 5 mA to 1A, TJ = +125°C ZOUT Output impedance IO = 100 mA DC and 20 mA rms VI = VO+2.5 V, IO = 5 mA, ON mode (+25°C) VI = VO+2.5 V, IO = 30 mA, ON mode (+25°C) Iq Quiescent current VI = VO+2.5 V, IO = 300 mA, ON mode (+25°C) VI = VO+2.5 V, IO = 1 A, ON mode (+25°C) VI = VO+2 V, VINH = 2.4 V, OFF mode VI = VO+2.5 V, IO = 30 mA, (-55°C) VI = VO+2.5 V, IO = 300 mA, (-55°C) VI = VO+2.5 V, IO = 1 A, (-55°C) VI = VO+2.5 V, IO = 30 mA, (+125°C) VI = VO+2.5 V, IO = 300 mA, (+125°C) VI = VO+2.5 V, IO = 1 A, (+125°C) Iq Quiescent current ON mode 6/20 Doc ID 10005 Rev 11 RHFL4913A Table 4. Symbol Electrical characteristics Electrical characteristics (continued) Parameter Test conditions IO = 400 mA, VO = 2.5 to 9 V, (+25°C) IO = 400 mA, VO = 2.5 to 9 V, (-55°C) IO = 400 mA, VO = 2.5 to 9 V, (+125°C) Min. Typ. 350 300 450 Max. 450 400 550 650 mV 550 800 900 950 0.8 V 2.4 f = 120 Hz f = 33 kHz 60 30 70 dB 40 15 0.38 ON-OFF OFF-ON 40 20 100 µA V µs µs µVrms Unit Vd Dropout voltage IO = 1 A, VO = 2.5 to 9 V, (+25°C) IO = 1 A, VO = 2.5 to 9 V, (-55°C) IO = 1 A, VO = 2.5 to 9 V, (+125°C) IO = 2 A, VO = 2.5 to 9 V, (+25°C) IO = 2 A, VO = 2.5 to 9 V, (+125°C) VINH(ON) Inhibit voltage VINH(OFF) Inhibit voltage SVR ISH VOCM tPLH tPHL eN Supply voltage rejection (1) IO = 5 mA, TJ = -55 to +125°C IO = 5 mA, TJ = -55 to +125°C VI = VO + 2.5 V ± 0.5 V, VO = 3 V IO = 5 mA Shutdown input current VINH = 5 V OCM pin voltage Inhibit propagation delay (1) Output noise voltage (1) Sinked IOCM = 24 mA active low VI = VO + 2.5V, VINH = 2.4 V, IO = 400 mA VO = 3 V B = 10 Hz to 100 kHz, IO = 5 mA to 2 A 1. These values are guaranteed by design. For each application it is strongly recommended to comply with the maximum current limit of the package used. Figure 3. Application diagram for remote sensing operation Doc ID 10005 Rev 11 7/20 Device description RHFL4913A 5 Device description The RHFL4913A adjustable voltage regulator contains a PNP type power element controlled by a signal resulting from an amplified comparison between the internal temperature-compensated band-gap and the fraction of the desired output voltage value obtained from an external resistor divider bridge. The device is protected by several functional blocks. 5.1 ADJ pin The load output voltage feedback comes from an external resistor divider bridge mid-point connected to the ADJ pin (allowing all possible output voltage settings as per user requirements) established between load terminals. 5.2 Inhibit ON-OFF control By setting the INHIBIT pin TTL high, the device switches off the output current and voltage. The device is ON when the INHIBIT pin is set low. Since the INHIBIT pin is pulled down internally, it can be left floating in cases where the inhibit function is not used. 5.3 Overtemperature protection A temperature detector internally monitors the power element junction temperature. The device turns off when a temperature of approximately 175 °C is reached, returning to ON mode when back to approximately 135 °C. Combined with the other protection blocks, the device is protected from destructive junction temperature excursions in all load conditions. It should be noted that when the internal temperature detector reaches 175 °C, the active power element can be as high as 225 °C. Prolonged operation under these conditions far exceeds the maximum operating ratings and device reliability cannot be guaranteed. 5.4 Overcurrent protection An internal non fold-back short circuit limitation is set with ISHORT > 3.8 A (VO is 0 V). This value can be decreased via an external resistor connected between the ISC and VI pins, with a typical value range of 10 kΩ to 200 kΩ. To maintain optimal VO regulation, it is necessary to set ISHORT 1.6 times greater than the maximum desired application IO. When IO reaches ISHORT – 300 mA, the current limiter overrules the regulation, VO starts to drop and the OCM flag is raised. When no current limitation adjustment is required, the ISC pin must be left unbiased (as it is in 3 pin packages). 5.5 OCM pin The OCM pin goes low when the current limit becomes active, otherwise VOCM = VI. It is buffered and can sink 10 mA. The OCM pin is internally pulled up by a 5 kΩ resistor. 8/20 Doc ID 10005 Rev 11 RHFL4913A Device description 5.6 Alternatives to the RHFL4913A The adjustable RHFL4913A is recommended to replace all industry positive voltage regulators due to its exceptional radiation performance. To replace 3-terminal industry devices, the fixed voltage versions of the RHFL4913A should be used. Doc ID 10005 Rev 11 9/20 Application information RHFL4913A 6 Application information To adjust the output voltage, the R2 resistor must be connected between the VO and ADJ pins. The R1 resistor must be connected between ADJ and ground. Resistor values can be derived from the following formula: VO = VADJ (R1+ R2) / R1 The VADJ is 1.23 V, controlled by the internal temperature-compensated band gap block. The minimum output voltage is therefore 1.22 V and minimum input voltage is 3 V. The RHFL4913A adjustable is functional as soon as the VI - VO voltage difference is slightly above the power element saturation voltage. The adjust pin to ground resistor value must not be greater than 10 kΩ, in order to keep the output feedback error below 0.2%. A minimum of 0.5 mA IO must be set to ensure perfect no-load regulation. It is advisable to dissipate this current into the divider bridge resistor. All available VI pins, as well as all available VO pins, should always be externally interconnected, otherwise the stability and reliability of the device cannot be guaranteed. The inhibit function switches off the output current electronically, and therefore very quickly. According to Lenz’s Law, external circuitry reacts with LdI/dt terms which can be of high amplitude in case somewhere a serial coil inductance exists. Large transient voltage would develop on both device terminals. It is advisable to protect the device with Schottky diodes to prevent negative voltage excursions. In the worst case, a 14 V Zener diode could protect the device input. The device has been designed for high stability and low dropout operation. Therefore, tantalum input and output capacitors with a minimum 1 µF are mandatory. Capacitor ESR range is from 0.01 Ω to over 20 Ω. This range is useful when ESR increases at low temperature. When large transient currents are expected, larger value capacitors are necessary. In the case of high current operation with short circuit events expected, caution must be exercised with regard to capacitors. They must be connected as close as possible to the device terminals. As some tantalum capacitors may permanently fail when subjected to high charge-up surge currents, it is recommended to decouple them with 470 nF polyester capacitors. Since the RHFL4913A adjustable voltage regulator is manufactured with very high speed bipolar technology (6 GHz fT transistors), the PCB layout must be designed with exceptional care, with very low inductance and low mutually coupling lines. Otherwise, high frequency parasitic signals may be picked up by the device resulting in system self-oscillation. The benefit is an SVR performance extended to far higher frequencies. 6.1 Notes on the 16-pin hermetic package The bottom section of the 16-pin package is metallized in order to allow the user to directly solder the RHFL4913A onto the equipment heat sink for enhanced heat removal. 6.2 Remote sensing operation A separate kelvin voltage sensing line provides the ADJ pin with exact load "high potential" information (see Figure 3). But variable remote load current consumption induces variable Iq current (Iq is roughly the IO current divided by the hFE of the internal PNP series power element) routed through the parasitic series line resistor RW2. To compensate for this 10/20 Doc ID 10005 Rev 11 RHFL4913A Application information parasitic voltage, resistor RW1can be introduced to provide the necessary compensating voltage signal to the ADJUST pin. 6.3 FPGA power supply lines Because these devices are very sensitive to VDD transients beyond a few % of their nominal supply voltage (usually 1.5 V), special attention must be given by supply lines designers to mitigate possible heavy ion L4913 disturbances. The worst case heavy ion effect can be summarized as: the L4913 internal control loop being cut (made open) or short-circuited for a sub-microsecond duration. During such an event, the L4913 die power element can either provide excessive current or current supply stoppage to the output (VOUT) for a duration of about one microsecond, after which time the L4913 smoothly recovers to nominal operation. To mitigate these "transients", it is recommended to implement the L4913 PCB layout as follows: ● ● ● Minimizing series/parallel parasitic inductances of the PC path Using a low ESR 47 µF Tantalum VOUT filtering capacitor with a 470 nF ceramic capacitor in parallel with the former (to reduce dynamic ESR) Inserting a 100-200 nH ferrite core on the VOUT-to-tantalum capacitor wire With this implementation, the ELDO simulated worst transient case shows no more than 90 mV deviation from the nominal line voltage value. Doc ID 10005 Rev 11 11/20 Die information RHFL4913A 7 Figure 4. Die information Die map GND 0;1002 13 INBH -1542;868 ADJ -1545;574 SENSE -1545;287 14 15 16 10 8 OCM 1517;5 Short 1517;2 1-2 3-4-5 6-7 VO -890;-974 VI 0;-974 VO 970;-974 Note: Pad numbers reflect terminal numbers when placed in case FLAT-16. 12/20 Doc ID 10005 Rev 11 RHFL4913A Die information 7.1 Die bonding pad locations and electrical functions Die physical dimensions: Die size: 150 mils x 110 mils (3.81 mm by 2.79 mm) Die thickness: 375 µm ± 25 µm (14.8 mils ± 1 mil) Pad size: VIN, VOUT pads: 450 µm x 330 µm (17.7 mils by 13 mils) Control pads: 184 µm x 184 µm (7.25 mils square) Interface materials: Top metallization: Al/Si/Cu, 1.05 µm ± 0.15 µm Backside metallization: none Glassivation: Type: p. vapox + nitride Thickness: 0.6 µm ± 0.1 µm + 0.6 µm ± 0.08 µm Substrate: bare silicon Assembly related information: Substrate potential: floating recommended to be tied to ground Special assembly instructions: "Sense" pad not used; not internally connected to any part of the IC. Can be connected to ground when space anti-static electricity rules apply. Doc ID 10005 Rev 11 13/20 Package mechanical data RHFL4913A 8 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 14/20 Doc ID 10005 Rev 11 RHFL4913A Package mechanical data FLAT-16 (MIL-STD-1835) mechanical data mm. Dim. Min. A b c D E E2 E3 e L Q S1 0.66 0.13 0.76 1.27 6.72 1.14 0.026 0.005 2.16 0.43 0.13 9.91 6.91 4.32 0.030 0.050 0.265 0.045 Typ. Max. 2.72 Min. 0.085 0.017 0.005 0.390 0.272 0.170 Typ. Max. 0.107 inch. e b c L E3 16 9 E E2 1 8 E3 L S1 D Q A 7450901A Doc ID 10005 Rev 11 15/20 Package mechanical data RHFL4913A SMD5C mechanical data Dim. A A1 b b1 b2 b3 D D1 E e mm. Min. 2.84 0.25 7.13 4.95 2.28 2.92 13.71 0.76 7.39 7.52 1.91 7.65 Typ. 3.00 0.38 7.26 5.08 2.41 3.05 13.84 Max. 3.15 0.51 7.39 5.21 2.54 3.18 13.97 Min. 0.112 0.010 0.281 0.195 0.090 0.115 0.540 0.030 0.291 0.296 0.075 0.301 inch. Typ. 0.118 0.015 0.286 0.200 0.095 0.120 0.545 Max. 0.124 0.020 0.291 0.205 0.100 0.125 0.550 7924296B 16/20 Doc ID 10005 Rev 11 RHFL4913A Packaging 9 Packaging The RHFL4913A adjustable voltage regulator is available in a high thermal dissipation 16pin hermetic Flat package, the bottom flange of which is metallized to allow direct soldering to a heat sink (efficient thermal conductivity). The device is also available in the SMD5C hermetic ceramic package. Doc ID 10005 Rev 11 17/20 Ordering information RHFL4913A 10 Table 5. Die Ordering information Order codes FLAT-16 RHFL4913KPA-01V RHFL4913KPA-02V RHFL4913KPA1 RHFL4913KPA2 RHFL4913SCA1 RHFL4913SCA2 SMD5C RHFL49143SCA-07V Terminal finish Gold Solder Gold Gold Output voltage Adj Adj Adj Adj Adj Adj Quality level QML-V QML-V EM1 EM2=EM1+48hours B.I. QML-V die EM1 die L4913ADIE2V L4913ADIES Table 6. Part numbers - SMD equivalent ST part number RHFL4913KPA-01V RHFL4913KPA-02V RHFL4913SCA-07V L4913ADIE2V SMD part number 5962F0252401VXC 5962F0252401VXA 5962F0252403VUC 5962F0252401V9A Table 7. Environmental characteristics Parameter Conditions -55°C to +125°C From 0 krad to 300 krad at 0.55 rad/s From 0 krad to 300 krad, Mil Std 883E Method 1019.6 Value 40 8 6 Unit ppm/°C ppm/krad ppm/krad Output voltage thermal drift Output voltage radiation drift Output voltage radiation drift 18/20 Doc ID 10005 Rev 11 RHFL4913A Revision history 11 Table 8. Date Revision history Document revision history Revision 3 4 5 6 7 8 9 10 11 Changes New order codes added - Tables 4 and 5. Features, Tables 4, 5 and the Figure 1 has been updated. Add the Mechanical Data SOC-16. Mistake on Table 4 (Q.ty Level), Table 7 has been updated and add DIE Information. Added new package SMD5C and removed old package SOC-16. DIE Information and DIE Pad has been updated par. 6, pages 9 and 10. Pin information for the SMD5C package updated in Table 1; added section 6.3: FPGA power supply lines on page 11. Minor text changes. Modified Application information on page 10. Modified Table 6 on page 18. Modified Table 5 on page 18. 29-Oct-2004 27-May-2005 08-Jun-2005 30-Jan-2006 26-Jan-2007 23-Nov-2007 22-Sep-2008 17-Nov-2008 21-Jan-2010 Doc ID 10005 Rev 11 19/20 RHFL4913A Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20 Doc ID 10005 Rev 11