ST25R3909-BQTM

ST25R3909 ISO-14443 A/B, 13.56 MHz mid-range reader Data brief - not recommended for new design Description The ST25R3909 is a high performance 13.56 MHz RFID reader, with two differential, low impedance (1.5 Ohm) antenna drivers. These drivers are unmatched, allowing the ST25R3909 to deliver up to eight times the output power of a standard HF reader IC using the same power supply voltage, and reducing in half the power consumption at the same output power. QFN32 Features • Close loop adjustment of ASK modulation for accurate control of modulation depth in case of ISO-14443 B protocol • Low power (3.5 μA) NFC target mode • AM/PM demodulator • Accurate RF envelope measurement (8-bit A/D converter) • High output power at 3.3 V power supply: – Up to 700 mW in case regulator is externally shorted – Up to 500 mW in case of differential output when antenna trimming is used – Up to 125 mW in case of single ended output when antenna trimming is used • Squelch for gain reduction, to compensate for noise generated by transponder processing • Transparent mode • Amplitude and phase measurement • Supporting 13.56 MHz and 27.12 MHz quartz oscillators with fast start-up • Supply voltage range from 2.4 to 3.6 V • Wide temperature range: -40 ºC to 85 ºC • Package: 32-pin QFN32, 5 mm x 5 mm November 2016 The ST25R3909 can operate already at 2.4 V, with a low power operating mode of 5 mA, making it perfectly suited for portable or battery-powered applications. For applications where high power is required the ST25R3909 can deliver up to 700 mW, thus avoiding the need for complex external booster circuitry. The component count and complexity of the design is further reduced through automatic modulation depth adjustment. The analog front end (AFE) is complemented by a highly integrated data framing engine for both ISO-14443 A and B. This includes data rates up to 848 kbit/s, with all framing and synchronization tasks on board, and enables to build a complete HF RFID reader using only a low end microcontroller. The ST25R3909 supports reader to tag and Peer to Peer communication using the NFCIP-1 active communication mode with a 106 kbps data rate. Other standard and custom protocols, such as ISO-15693 or FeliCa™ can be implemented via transparent mode. The ST25R3909 features a SPI, which enables bi-directional communication with the external microcontroller. DocID029999 Rev 1 This is information on a product still in production but not recommended for new designs. For further information contact your local STMicroelectronics sales office. 1/3 www.st.com Revision history 1 ST25R3909 Revision history Table 1. Document revision history 2/3 Date Revision 15-Nov-2016 1 Changes Initial release. DocID029999 Rev 1 ST25R3909 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID029999 Rev 1 3/3 3