ST7LITE0xY0, ST7LITESxY0
8-bit microcontroller with single voltage
Flash memory, data EEPROM, ADC, timers, SPI
■
■
■
■
■
Memories
– 1K or 1.5 Kbytes single voltage Flash Program memory with read-out protection, In-Circuit and In-Application Programming (ICP and
IAP). 10 K write/erase cycles guaranteed,
data retention: 20 years at 55 °C.
– 128 bytes RAM.
– 128 bytes data EEPROM with read-out protection. 300K write/erase cycles guaranteed,
data retention: 20 years at 55 °C.
Clock, Reset and Supply Management
– 3-level low voltage supervisor (LVD) and auxiliary voltage detector (AVD) for safe poweron/off procedures
– Clock sources: internal 1MHz RC 1% oscillator or external clock
– PLL x4 or x8 for 4 or 8 MHz internal clock
– Four Power Saving Modes: Halt, Active-Halt,
Wait and Slow
Interrupt Management
– 10 interrupt vectors plus TRAP and RESET
– 4 external interrupt lines (on 4 vectors)
I/O Ports
– 13 multifunctional bidirectional I/O lines
– 9 alternate function lines
– 6 high sink outputs
2 Timers
– One 8-bit Lite Timer (LT) with prescaler including: watchdog, 1 realtime base and 1 input capture.
SO16
150”
DIP16
QFN20
– One 12-bit Auto-reload Timer (AT) with output
compare function and PWM
■
1 Communication Interface
– SPI synchronous serial interface
■
A/D Converter
– 8-bit resolution for 0 to VDD
– Fixed gain Op-amp for 11-bit resolution in 0 to
250 mV range (@ 5V VDD)
– 5 input channels
■
Instruction Set
– 8-bit data manipulation
– 63 basic instructions with illegal opcode detection
– 17 main addressing modes
– 8 x 8 unsigned multiply instruction
■
Development Tools
– Full hardware/software development package
Device Summary
Features
Program memory - bytes
RAM (stack) - bytes
Data EEPROM - bytes
Peripherals
Operating Supply
CPU Frequency
Operating Temperature
Packages
ST7LITESxY0 (ST7SUPERLITE)
ST7LITES2Y0
ST7LITES5Y0
ST7LITE02Y0
ST7LITE0xY0
ST7LITE05Y0
1K
1K
1.5K
128 (64)
128 (64)
128 (64)
LT Timer w/ Wdg,
LT Timer w/ Wdg,
LT Timer w/ Wdg,
AT Timer w/ 1 PWM, AT Timer w/ 1 PWM, AT Timer w/ 1 PWM,
SPI
SPI, 8-bit ADC
SPI
2.4V to 5.5V
1MHz RC 1% + PLLx4/8MHz
-40°C to +85°C
SO16 150”, DIP16, QFN20
ST7LITE09Y0
1.5K
1.5K
128 (64)
128 (64)
128
LT Timer w/ Wdg,
AT Timer w/ 1 PWM, SPI,
8-bit ADC w/ Op-Amp
Rev 6
November 2007
1/124
1
Table of Contents
ST7LITE0xY0, ST7LITESxY0 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 REGISTER & MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 FLASH PROGRAM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2
MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3
PROGRAMMING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.4
ICC INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.5
MEMORY PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.6
RELATED DOCUMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.7
REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 DATA EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2
MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3
MEMORY ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.4
POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.5
ACCESS ERROR HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.6
DATA EEPROM READ-OUT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.7
REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.2
MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.3
CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7 SUPPLY, RESET AND CLOCK MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.1 INTERNAL RC OSCILLATOR ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.2
PHASE LOCKED LOOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.3
REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
7.4
RESET SEQUENCE MANAGER (RSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
8 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.1 NON MASKABLE SOFTWARE INTERRUPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.2
EXTERNAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.3
PERIPHERAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
8.4
SYSTEM INTEGRITY MANAGEMENT (SI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
9 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9.2
9.3
SLOW MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
WAIT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
. . . . 38
9.4
ACTIVE-HALT AND HALT MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2/124
2
Table of Contents
10 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
10.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
10.2 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
10.3 UNUSED I/O PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10.4 LOW POWER MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10.5 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10.6 I/O PORT IMPLEMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
11 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
11.1 LITE TIMER (LT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
11.2
12-BIT AUTORELOAD TIMER (AT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
11.3 SERIAL PERIPHERAL INTERFACE (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.4 8-BIT A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
12 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
12.1 ST7 ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
12.2 INSTRUCTION GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
13 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
13.1 PARAMETER CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
13.2 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
13.3 OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
13.4 SUPPLY CURRENT CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
13.5 CLOCK AND TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
13.6 MEMORY CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
13.7 EMC (ELECTROMAGNETIC COMPATIBILITY) CHARACTERISTICS . . . . . . . . . . . . . 93
13.8 I/O PORT PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
13.9 CONTROL PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
13.10 COMMUNICATION INTERFACE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . 102
13.11 8-BIT ADC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14 PACKAGE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
14.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
14.2 THERMAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
15 DEVICE CONFIGURATION AND ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 112
15.1 OPTION BYTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
15.2 DEVICE ORDERING INFORMATION AND TRANSFER OF CUSTOMER CODE . . . . 114
15.3 DEVELOPMENT TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
15.4 ST7 APPLICATION NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
16 KNOWN LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
16.1 EXECUTION OF BTJX INSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
16.2 IN-CIRCUIT PROGRAMMING OF DEVICES PREVIOUSLY PROGRAMMED WITH HARDWARE WATCHDOG OPTION 121
16.3 IN-CIRCUIT DEBUGGING WITH HARDWARE WATCHDOG . . . . . . . . . . . . . . . . . . . 121
16.4 RECOMMENDATIONS WHEN LVD IS ENABLED . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
16.5 CLEARING ACTIVE INTERRUPTS OUTSIDE INTERRUPT ROUTINE . . . . . . . . . . . . 121
17 REVISION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
3/124
3
Table of Contents
To obtain the most recent version of this datasheet,
please check at www.st.com
Please also pay special attention to the Section “KNOWN LIMITATIONS” on page 121.
4/124
1
ST7LITE0xY0, ST7LITESxY0
1 DESCRIPTION
The
ST7LITE0x
and
ST7SUPERLITE
(ST7LITESx) are members of the ST7 microcontroller family. All ST7 devices are based on a common industry-standard 8-bit core, featuring an enhanced instruction set.
The ST7LITE0x and ST7SUPERLITE feature
FLASH memory with byte-by-byte In-Circuit Programming (ICP) and In-Application Programming
(IAP) capability.
Under software control, the ST7LITE0x and
ST7SUPERLITE devices can be placed in WAIT,
SLOW, or HALT mode, reducing power consumption when the application is in idle or standby state.
The enhanced instruction set and addressing
modes of the ST7 offer both power and flexibility to
software developers, enabling the design of highly
efficient and compact application code. In addition
to standard 8-bit data management, all ST7 microcontrollers feature true bit manipulation, 8x8 unsigned multiplication and indirect addressing
modes.
For easy reference, all parametric data are located
in section 13 on page 81.
Figure 1. General Block Diagram
1 MHz. RC OSC
+
PLL x 4 or x 8
Internal
CLOCK
LITE TIMER
VDD
VSS
POWER
SUPPLY
PORT A
CONTROL
8-BIT CORE
ALU
FLASH
MEMORY
(1 or 1.5K Bytes)
ADDRESS AND DATA BUS
RESET
LVD/AVD
w/ WATCHDOG
PA7:0
(8 bits)
12-BIT AUTORELOAD TIMER
SPI
PORT B
PB4:0
(5 bits)
8-BIT ADC
RAM
(128 Bytes)
DATA EEPROM
(128 Bytes)
5/124
1
ST7LITE0xY0, ST7LITESxY0
2 PIN DESCRIPTION
PA0 (HS)/LTIC
VSS
VDD
PB0/SS/AIN0
Figure 2. 20-Pin QFN Package Pinout
20 19 18
17
e3
e0
16
PA1 (HS)
2
15
PA2 (HS)/ATPWM0
NC
3
14
PA3 (HS)
NC
4
13
NC
MISO/AIN2/PB2
5
12
PA4 (HS)
11
PA5 (HS)/ICCDATA
RESET
1
NC
ei1
ei2
7
8
9
10
CLKIN/AIN4/PB4
PA7
MCO/ICCCLK/PA6
6
MOSI/AIN3/PB3
SCK/AIN1/PB1
(HS) 20mA High sink capability
eix associated external interrupt vector
Figure 3. 16-Pin SO and DIP Package Pinout
k
VSS
1
ei0 16
VDD
RESET
2
15
3
14
4 ei3
13
PA3 (HS)
5
12
PA4 (HS)
MISO/AIN2/PB2
6
11
PA5 (HS)/ICCDATA
MOSI/AIN3/PB3
7 ei2
10
PA6/MCO/ICCCLK
SS/AIN0/PB0
SCK/AIN1/PB1
CLKIN/AIN4/PB4
8
ei1
9
PA0 (HS)/LTIC
PA1 (HS)
PA2 (HS)/ATPWM0
PA7
(HS) 20mA high sink capability
eix associated external interrupt vector
6/124
1
ST7LITE0xY0, ST7LITESxY0
PIN DESCRIPTION (Cont’d)
Legend / Abbreviations for Table 1:
Type:
I = input, O = output, S = supply
In/Output level: C= CMOS 0.15VDD/0.85VDD with input trigger
CT= CMOS 0.3VDD/0.7VDD with input trigger
Output level:
HS = 20mA high sink (on N-buffer only)
Port and control configuration:
– Input:
float = floating, wpu = weak pull-up, int = interrupt 1), ana = analog
– Output:
OD = open drain, PP = push-pull
Table 1. Device Pin Description
Port / Control
VSS
S
Ground
19
2
VDD
S
Main power supply
1
3
RESET
I/O
CT
20
4
PB0/AIN0/SS
I/O
CT
X
6
5
PB1/AIN1/SCK
I/O
CT
X
5
6
PB2/AIN2/MISO
I/O
CT
X
7
7
PB3/AIN3/MOSI
I/O
CT
X
8
8
PB4/AIN4/CLKIN
I/O
CT
X
9
9
PA7
I/O
CT
X
X
PP
OD
Output
ana
int
wpu
Input
float
Output
1
Input
18
Pin Name
Type
SO16/DIP16
Level
QFN20
Pin n°
X
ei3
Main
Function
(after reset)
Top priority non maskable interrupt (active low)
X
X
X
Port B0
X
X
X
X
Port B1
X
X
X
X
Port B2
X
X
X
Port B3
X
X
X
Port B4
X
X
Port A7
ei2
X
ei1
Alternate Function
ADC Analog Input 0 or SPI Slave
Select (active low)
ADC Analog Input 1 or SPI Clock
Caution: No negative current injection allowed on this pin. For
details, refer to section 13.2.2 on
page 82
ADC Analog Input 2 or SPI Master In/ Slave Out Data
ADC Analog Input 3 or SPI Master Out / Slave In Data
ADC Analog Input 4 or External
clock input
X
X
X
X
Port A6
Main Clock Output/In Circuit
Communication Clock.
Caution: During normal operation this pin must be pulled- up,
internally or externally (external
pull-up of 10k mandatory in noisy
environment). This is to avoid entering ICC mode unexpectedly
during a reset. In the application,
even if the pin is configured as
output, any reset will put it back in
input pull-up
I/O CT HS
X
X
X
X
Port A5
In Circuit Communication Data
12 12 PA4
I/O CT HS
X
X
X
X
Port A4
14 13 PA3
I/O CT HS
X
X
X
X
Port A3
10 10
PA6 /MCO/
ICCCLK
I/O
11 11
PA5/
ICCDATA
CT
7/124
1
ST7LITE0xY0, ST7LITESxY0
Level
Port / Control
PP
X
X
X
Port A2
16 15 PA1
I/O CT HS
X
X
X
X
Port A1
17 16 PA0/LTIC
I/O CT HS
X
X
X
Port A0
ei0
ana
X
int
I/O CT HS
Pin Name
Input
15 14 PA2/ATPWM0
QFN20
OD
Main
Function
(after reset)
wpu
Output
float
Input
Output
Type
SO16/DIP16
Pin n°
Alternate Function
Auto-Reload Timer PWM0
Lite Timer Input Capture
Note:
In the interrupt input column, “eix” defines the associated external interrupt vector. If the weak pull-up column (wpu) is merged with the interrupt column (int), then the I/O configuration is pull-up interrupt input,
else the configuration is floating interrupt input.
8/124
1
ST7LITE0xY0, ST7LITESxY0
3 REGISTER & MEMORY MAP
As shown in Figure 4 and Figure 5, the MCU is capable of addressing 64K bytes of memories and I/
O registers.
The available memory locations consist of up to
128 bytes of register locations, 128 bytes of RAM,
128 bytes of data EEPROM and up to 1.5 Kbytes
of user program memory. The RAM space includes up to 64 bytes for the stack from 0C0h to
0FFh.
The highest address bytes contain the user reset
and interrupt vectors.
The size of Flash Sector 0 is configurable by Option byte.
IMPORTANT: Memory locations marked as “Reserved” must never be accessed. Accessing a reserved area can have unpredictable effects on the
device.
Figure 4. Memory Map (ST7LITE0x)
0000h
007Fh
0080h
HW Registers
(see Table 2)
RAM
(128 Bytes)
00FFh
0100h
0080h
Short Addressing
RAM (zero page)
00BFh
00C0h
64 Bytes Stack
00FFh
Reserved
0FFFh
1000h
107Fh
1080h
Data EEPROM
(128 Bytes)
F9FFh
FA00h
1001h
RCCR1
1.5K FLASH
PROGRAM MEMORY
FA00h
Flash Memory
(1.5K)
FBFFh
FC00h
FFFFh
FFFFh
RCCR0
see section 7.1 on page 24
Reserved
FFDFh
FFE0h
1000h
Interrupt & Reset Vectors
(see Table 6)
0.5 Kbytes
SECTOR 1
1 Kbytes
SECTOR 0
FFDEh
RCCR0
FFDFh
RCCR1
see section 7.1 on page 24
9/124
1
ST7LITE0xY0, ST7LITESxY0
REGISTER AND MEMORY MAP (Cont’d)
Figure 5. Memory Map (ST7SUPERLITE)
0000h
007Fh
0080h
HW Registers
(see Table 2)
RAM
(128 Bytes)
00FFh
0100h
0080h
Short Addressing
RAM (zero page)
00BFh
00C0h
64 Bytes Stack
00FFh
Reserved
1K FLASH
PROGRAM MEMORY
FBFFh
FC00h
FC00h
Flash Memory
(1K)
FDFFh
FE00h
FFFFh
FFDFh
FFE0h
FFFFh
Interrupt & Reset Vectors
(see Table 6)
0.5 Kbytes
SECTOR 1
0.5 Kbytes
SECTOR 0
FFDEh
RCCR0
FFDFh
RCCR1
see section 7.1 on page 24
10/124
1
ST7LITE0xY0, ST7LITESxY0
REGISTER AND MEMORY MAP (Cont’d)
Legend: x=undefined, R/W=read/write
Table 2. Hardware Register Map
Address
0000h
0001h
0002h
0003h
0004h
0005h
Block
Register
Label
000Dh
000Eh
000Fh
0010h
0011h
0012h
0013h
Remarks
Port A
Port A Data Register
Port A Data Direction Register
Port A Option Register
00h1)
00h
40h
R/W
R/W
R/W
Port B
PBDR
PBDDR
PBOR
Port B Data Register
Port B Data Direction Register
Port B Option Register
E0h 1)
00h
00h
R/W
R/W
R/W2)
Reserved area (5 bytes)
LITE
TIMER
LTCSR
LTICR
ATCSR
CNTRH
CNTRL
AUTO-RELOAD
ATRH
TIMER
ATRL
PWMCR
PWM0CSR
0014h to
0016h
0017h
0018h
Reset
Status
PADR
PADDR
PAOR
0006h to
000Ah
000Bh
000Ch
Register Name
Lite Timer Control/Status Register
Lite Timer Input Capture Register
xxh
xxh
R/W
Read Only
Timer Control/Status Register
Counter Register High
Counter Register Low
Auto-Reload Register High
Auto-Reload Register Low
PWM Output Control Register
PWM 0 Control/Status Register
00h
00h
00h
00h
00h
00h
00h
R/W
Read Only
Read Only
R/W
R/W
R/W
R/W
00h
00h
R/W
R/W
Reserved area (3 bytes)
AUTO-RELOAD DCR0H
TIMER
DCR0L
0019h to
002Eh
PWM 0 Duty Cycle Register High
PWM 0 Duty Cycle Register Low
Reserved area (22 bytes)
0002Fh
FLASH
FCSR
Flash Control/Status Register
00h
R/W
00030h
EEPROM
EECSR
Data EEPROM Control/Status Register
00h
R/W
0031h
0032h
0033h
SPI
SPIDR
SPICR
SPICSR
SPI Data I/O Register
SPI Control Register
SPI Control/Status Register
xxh
0xh
00h
R/W
R/W
R/W
0034h
0035h
0036h
ADC
ADCCSR
ADCDR
ADCAMP
A/D Control Status Register
A/D Data Register
A/D Amplifier Control Register
00h
00h
00h
R/W
Read Only
R/W
0037h
ITC
EICR
External Interrupt Control Register
00h
R/W
MCCSR
RCCR
Main Clock Control/Status Register
RC oscillator Control Register
00h
FFh
R/W
R/W
0038h
0039h
CLOCKS
11/124
1
ST7LITE0xY0, ST7LITESxY0
Address
Block
003Ah
SI
003Bh to
007Fh
Register
Label
SICSR
Register Name
System Integrity Control/Status Register
Reset
Status
0xh
Remarks
R/W
Reserved area (69 bytes)
Notes:
1. The contents of the I/O port DR registers are readable only in output configuration. In input configuration, the values of the I/O pins are returned instead of the DR register contents.
2. The bits associated with unavailable pins must always keep their reset value.
12/124
1
ST7LITE0xY0, ST7LITESxY0
4 FLASH PROGRAM MEMORY
4.1 Introduction
The ST7 single voltage extended Flash (XFlash) is
a non-volatile memory that can be electrically
erased and programmed either on a byte-by-byte
basis or up to 32 bytes in parallel.
The XFlash devices can be programmed off-board
(plugged in a programming tool) or on-board using
In-Circuit Programming or In-Application Programming.
The array matrix organisation allows each sector
to be erased and reprogrammed without affecting
other sectors.
4.2 Main Features
■
■
■
■
■
ICP (In-Circuit Programming)
IAP (In-Application Programming)
ICT (In-Circuit Testing) for downloading and
executing user application test patterns in RAM
Sector 0 size configurable by option byte
Read-out and write protection
4.3 PROGRAMMING MODES
The ST7 can be programmed in three different
ways:
– Insertion in a programming tool. In this mode,
FLASH sectors 0 and 1, option byte row and
data EEPROM can be programmed or
erased.
– In-Circuit Programming. In this mode, FLASH
sectors 0 and 1, option byte row and data
EEPROM can be programmed or erased without removing the device from the application
board.
– In-Application Programming. In this mode,
sector 1 and data EEPROM can be programmed or erased without removing the device from the application board and while the
application is running.
4.3.1 In-Circuit Programming (ICP)
ICP uses a protocol called ICC (In-Circuit Communication) which allows an ST7 plugged on a printed circuit board (PCB) to communicate with an external programming device connected via cable.
ICP is performed in three steps:
Switch the ST7 to ICC mode (In-Circuit Communications). This is done by driving a specific signal
sequence on the ICCCLK/DATA pins while the
RESET pin is pulled low. When the ST7 enters
ICC mode, it fetches a specific RESET vector
which points to the ST7 System Memory containing the ICC protocol routine. This routine enables
the ST7 to receive bytes from the ICC interface.
– Download ICP Driver code in RAM from the
ICCDATA pin
– Execute ICP Driver code in RAM to program
the FLASH memory
Depending on the ICP Driver code downloaded in
RAM, FLASH memory programming can be fully
customized (number of bytes to program, program
locations, or selection of the serial communication
interface for downloading).
4.3.2 In Application Programming (IAP)
This mode uses an IAP Driver program previously
programmed in Sector 0 by the user (in ICP
mode).
This mode is fully controlled by user software. This
allows it to be adapted to the user application, (user-defined strategy for entering programming
mode, choice of communications protocol used to
fetch the data to be stored etc.)
IAP mode can be used to program any memory areas except Sector 0, which is write/erase protected to allow recovery in case errors occur during
the programming operation.
13/124
1
ST7LITE0xY0, ST7LITESxY0
FLASH PROGRAM MEMORY (Cont’d)
4.4 ICC interface
high level (push pull output or pull-up resistor1K or a reset management IC with open drain output and pull-up resistor>1K, no additional components are needed.
In all cases the user must ensure that no external
reset is generated by the application during the
ICC session.
3. The use of Pin 7 of the ICC connector depends
on the Programming Tool architecture. This pin
must be connected when using most ST Programming Tools (it is used to monitor the application
power supply). Please refer to the Programming
Tool manual.
4. Pin 9 has to be connected to the CLKIN pin of
the ST7 when the clock is not available in the application or if the selected clock option is not programmed in the option byte.
Caution: During normal operation, ICCCLK pin
must be pulled- up, internally or externally (external pull-up of 10K mandatory in noisy environment). This is to avoid entering ICC mode unexpectedly during a reset. In the application, even if
the pin is configured as output, any reset will put it
back in input pull-up.
ICP needs a minimum of 4 and up to 6 pins to be
connected to the programming tool. These pins
are:
– RESET: device reset
– VSS: device power supply ground
– ICCCLK: ICC output serial clock pin
– ICCDATA: ICC input serial data pin
– CLKIN: main clock input for external source
– VDD: application board power supply (optional, see Note 3)
Notes:
1. If the ICCCLK or ICCDATA pins are only used
as outputs in the application, no signal isolation is
necessary. As soon as the Programming Tool is
plugged to the board, even if an ICC session is not
in progress, the ICCCLK and ICCDATA pins are
not available for the application. If they are used as
inputs by the application, isolation such as a serial
resistor has to be implemented in case another device forces the signal. Refer to the Programming
Tool documentation for recommended resistor values.
2. During the ICP session, the programming tool
must control the RESET pin. This can lead to conflicts between the programming tool and the application reset circuit if it drives more than 5mA at
Figure 6. Typical ICC Interface
PROGRAMMING TOOL
ICC CONNECTOR
ICC Cable
ICC CONNECTOR
HE10 CONNECTOR TYPE
(See Note 3)
OPTIONAL
(See Note 4)
9
7
5
3
1
10
8
6
4
2
APPLICATION BOARD
APPLICATION
RESET SOURCE
See Note 2
APPLICATION
POWER SUPPLY
14/124
1
ICCDATA
ICCCLK
ST7
RESET
CLKIN
VDD
See Note 1 and Caution APPLICATION
I/O
See Note 1
ST7LITE0xY0, ST7LITESxY0
FLASH PROGRAM MEMORY (Cont’d)
4.5 Memory Protection
There are two different types of memory protection: Read Out Protection and Write/Erase Protection which can be applied individually.
4.5.1 Read out Protection
Readout protection, when selected provides a protection against program memory content extraction and against write access to Flash memory.
Even if no protection can be considered as totally
unbreakable, the feature provides a very high level
of protection for a general purpose microcontroller.
Both program and data E2 memory are protected.
In flash devices, this protection is removed by reprogramming the option. In this case, both program and data E2 memory are automatically
erased, and the device can be reprogrammed.
Read-out protection selection depends on the device type:
– In Flash devices it is enabled and removed
through the FMP_R bit in the option byte.
– In ROM devices it is enabled by mask option
specified in the Option List.
4.5.2 Flash Write/Erase Protection
Write/erase protection, when set, makes it impossible to both overwrite and erase program memory. It does not apply to E2 data. Its purpose is to
provide advanced security to applications and prevent any change being made to the memory content.
Warning: Once set, Write/erase protection can
never be removed. A write-protected flash device
is no longer reprogrammable.
Write/erase protection is enabled through the
FMP_W bit in the option byte.
4.6 Related Documentation
For details on Flash programming and ICC protocol, refer to the ST7 Flash Programming Reference Manual and to the ST7 ICC Protocol Reference Manual.
4.7 Register Description
FLASH CONTROL/STATUS REGISTER (FCSR)
Read/Write
Reset Value: 000 0000 (00h)
1st RASS Key: 0101 0110 (56h)
2nd RASS Key: 1010 1110 (AEh)
7
0
0
0
0
0
0
OPT
LAT
PGM
Note: This register is reserved for programming
using ICP, IAP or other programming methods. It
controls the XFlash programming and erasing operations.
When an EPB or another programming tool is
used (in socket or ICP mode), the RASS keys are
sent automatically.
Table 3. FLASH Register Map and Reset Values
Address
(Hex.)
002Fh
Register
Label
7
6
5
4
3
2
1
0
0
0
0
0
0
OPT
0
LAT
0
PGM
0
FCSR
Reset Value
15/124
1
ST7LITE0xY0, ST7LITESxY0
5 DATA EEPROM
5.1 INTRODUCTION
5.2 MAIN FEATURES
The Electrically Erasable Programmable Read
Only Memory can be used as a non-volatile backup for storing data. Using the EEPROM requires a
basic access protocol described in this chapter.
■
■
■
■
■
■
Up to 32 bytes programmed in the same cycle
EEPROM mono-voltage (charge pump)
Chained erase and programming cycles
Internal control of the global programming cycle
duration
WAIT mode management
Read-out protection
Figure 7. EEPROM Block Diagram
HIGH VOLTAGE
PUMP
EECSR
0
0
0
ADDRESS
DECODER
0
0
4
0
E2LAT E2PGM
EEPROM
ROW
MEMORY MATRIX
DECODER
(1 ROW = 32 x 8 BITS)
128
4
128
DATA
32 x 8 BITS
MULTIPLEXER
DATA LATCHES
4
ADDRESS BUS
16/124
1
DATA BUS
ST7LITE0xY0, ST7LITESxY0
DATA EEPROM (Cont’d)
5.3 MEMORY ACCESS
The Data EEPROM memory read/write access
modes are controlled by the E2LAT bit of the EEPROM Control/Status register (EECSR). The flowchart in Figure 8 describes these different memory
access modes.
Read Operation (E2LAT = 0)
The EEPROM can be read as a normal ROM location when the E2LAT bit of the EECSR register is
cleared.
On this device, Data EEPROM can also be used to
execute machine code. Take care not to write to
the Data EEPROM while executing from it. This
would result in an unexpected code being executed.
Write Operation (E2LAT = 1)
To access the write mode, the E2LAT bit has to be
set by software (the E2PGM bit remains cleared).
When a write access to the EEPROM area occurs,
the value is latched inside the 32 data latches according to its address.
When PGM bit is set by the software, all the previous bytes written in the data latches (up to 32) are
programmed in the EEPROM cells. The effective
high address (row) is determined by the last EEPROM write sequence. To avoid wrong programming, the user must take care that all the bytes
written between two programming sequences
have the same high address: Only the five Least
Significant Bits of the address can change.
At the end of the programming cycle, the PGM and
LAT bits are cleared simultaneously.
Note: Care should be taken during the programming cycle. Writing to the same memory location
will over-program the memory (logical AND between the two write access data result) because
the data latches are only cleared at the end of the
programming cycle and by the falling edge of the
E2LAT bit.
It is not possible to read the latched data.
This note is illustrated by the Figure 10.
Figure 8. Data EEPROM Programming Flowchart
READ MODE
E2LAT = 0
E2PGM = 0
READ BYTES
IN EEPROM AREA
WRITE MODE
E2LAT = 1
E2PGM = 0
WRITE UP TO 32 BYTES
IN EEPROM AREA
(with the same 11 MSB of the address)
START PROGRAMMING CYCLE
E2LAT=1
E2PGM=1 (set by software)
0
E2LAT
1
CLEARED BY HARDWARE
17/124
1
ST7LITE0xY0, ST7LITESxY0
DATA EEPROM (Cont’d)
Figure 9. Data E2PROM Write Operation
⇓ Row / Byte ⇒
ROW
DEFINITION
0
1
2
3
...
30 31
Physical Address
0
00h...1Fh
1
20h...3Fh
...
Nx20h...Nx20h+1Fh
N
Read operation impossible
Byte 1
Byte 2
Byte 32
Read operation possible
Programming cycle
PHASE 1
PHASE 2
Writing data latches
Waiting E2PGM and E2LAT to fall
E2LAT bit
Set by USER application
Cleared by hardware
E2PGM bit
Note: If a programming cycle is interrupted (by RESET action), the integrity of the data in memory will not
be guaranteed.
18/124
1
ST7LITE0xY0, ST7LITESxY0
DATA EEPROM (Cont’d)
5.4 POWER SAVING MODES
5.5 ACCESS ERROR HANDLING
Wait mode
The DATA EEPROM can enter WAIT mode on execution of the WFI instruction of the microcontroller or when the microcontroller enters Active Halt
mode.The DATA EEPROM will immediately enter
this mode if there is no programming in progress,
otherwise the DATA EEPROM will finish the cycle
and then enter WAIT mode.
If a read access occurs while E2LAT = 1, then the
data bus will not be driven.
If a write access occurs while E2LAT = 0, then the
data on the bus will not be latched.
If a programming cycle is interrupted (by RESET
action), the integrity of the data in memory will not
be guaranteed.
5.6 DATA EEPROM READ-OUT PROTECTION
Active Halt mode
Refer to Wait mode.
Halt mode
The DATA EEPROM immediately enters HALT
mode if the microcontroller executes the HALT instruction. Therefore the EEPROM will stop the
function in progress, and data may be corrupted.
The read-out protection is enabled through an option bit (see option byte section).
When this option is selected, the programs and
data stored in the EEPROM memory are protected
against read-out (including a re-write protection).
In Flash devices, when this protection is removed
by reprogramming the Option Byte, the entire Program memory and EEPROM is first automatically
erased.
Note: Both Program Memory and data EEPROM
are protected using the same option bit.
Figure 10. Data EEPROM Programming Cycle
READ OPERATION NOT POSSIBLE
READ OPERATION POSSIBLE
INTERNAL
PROGRAMMING
VOLTAGE
ERASE CYCLE
WRITE OF
DATA
LATCHES
WRITE CYCLE
tPROG
LAT
PGM
19/124
1
ST7LITE0xY0, ST7LITESxY0
DATA EEPROM (Cont’d)
5.7 REGISTER DESCRIPTION
EEPROM CONTROL/STATUS REGISTER (EECSR)
Read/Write
Reset Value: 0000 0000 (00h)
7
0
0
0
0
0
0
0
E2LAT E2PGM
Bits 7:2 = Reserved, forced by hardware to 0.
Bit 1 = E2LAT Latch Access Transfer
This bit is set by software. It is cleared by hardware at the end of the programming cycle. It can
only be cleared by software if the E2PGM bit is
cleared.
0: Read mode
1: Write mode
Bit 0 = E2PGM Programming control and status
This bit is set by software to begin the programming
cycle. At the end of the programming cycle, this bit
is cleared by hardware.
0: Programming finished or not yet started
1: Programming cycle is in progress
Note: If the E2PGM bit is cleared during the programming cycle, the memory data is not guaranteed.
Table 4. DATA EEPROM Register Map and Reset Values
Address
(Hex.)
0030h
20/124
1
Register
Label
7
6
5
4
3
2
1
0
0
0
0
0
0
0
E2LAT
0
E2PGM
0
EECSR
Reset Value
ST7LITE0xY0, ST7LITESxY0
6 CENTRAL PROCESSING UNIT
6.1 INTRODUCTION
This CPU has a full 8-bit architecture and contains
six internal registers allowing efficient 8-bit data
manipulation.
6.2 MAIN FEATURES
■
■
■
■
■
■
■
■
63 basic instructions
Fast 8-bit by 8-bit multiply
17 main addressing modes
Two 8-bit index registers
16-bit stack pointer
Low power modes
Maskable hardware interrupts
Non-maskable software interrupt
6.3 CPU REGISTERS
The six CPU registers shown in Figure 11 are not
present in the memory mapping and are accessed
by specific instructions.
Accumulator (A)
The Accumulator is an 8-bit general purpose register used to hold operands and the results of the
arithmetic and logic calculations and to manipulate
data.
Index Registers (X and Y)
In indexed addressing modes, these 8-bit registers
are used to create either effective addresses or
temporary storage areas for data manipulation.
(The Cross-Assembler generates a precede instruction (PRE) to indicate that the following instruction refers to the Y register.)
The Y register is not affected by the interrupt automatic procedures (not pushed to and popped from
the stack).
Program Counter (PC)
The program counter is a 16-bit register containing
the address of the next instruction to be executed
by the CPU. It is made of two 8-bit registers PCL
(Program Counter Low which is the LSB) and PCH
(Program Counter High which is the MSB).
Figure 11. CPU Registers
7
0
ACCUMULATOR
RESET VALUE = XXh
7
0
X INDEX REGISTER
RESET VALUE = XXh
7
0
Y INDEX REGISTER
RESET VALUE = XXh
15
PCH
8 7
PCL
0
PROGRAM COUNTER
RESET VALUE = RESET VECTOR @ FFFEh-FFFFh
7
1 1 1 H I
0
N Z C
CONDITION CODE REGISTER
RESET VALUE = 1 1 1 X 1 X X X
15
8 7
0
STACK POINTER
RESET VALUE = STACK HIGHER ADDRESS
X = Undefined Value
21/124
1
ST7LITE0xY0, ST7LITESxY0
CPU REGISTERS (Cont’d)
CONDITION CODE REGISTER (CC)
Read/Write
Reset Value: 111x1xxx
7
1
0
1
1
H
I
N
Z
because the I bit is set by hardware at the start of
the routine and reset by the IRET instruction at the
end of the routine. If the I bit is cleared by software
in the interrupt routine, pending interrupts are
serviced regardless of the priority level of the current interrupt routine.
C
The 8-bit Condition Code register contains the interrupt mask and four flags representative of the
result of the instruction just executed. This register
can also be handled by the PUSH and POP instructions.
These bits can be individually tested and/or controlled by specific instructions.
Bit 4 = H Half carry.
This bit is set by hardware when a carry occurs between bits 3 and 4 of the ALU during an ADD or
ADC instruction. It is reset by hardware during the
same instructions.
0: No half carry has occurred.
1: A half carry has occurred.
This bit is tested using the JRH or JRNH instruction. The H bit is useful in BCD arithmetic subroutines.
Bit 2 = N Negative.
This bit is set and cleared by hardware. It is representative of the result sign of the last arithmetic,
logical or data manipulation. It is a copy of the 7th
bit of the result.
0: The result of the last operation is positive or null.
1: The result of the last operation is negative
(that is, the most significant bit is a logic 1).
This bit is accessed by the JRMI and JRPL instructions.
Bit 1 = Z Zero.
This bit is set and cleared by hardware. This bit indicates that the result of the last arithmetic, logical
or data manipulation is zero.
0: The result of the last operation is different from
zero.
1: The result of the last operation is zero.
This bit is accessed by the JREQ and JRNE test
instructions.
Bit 3 = I Interrupt mask.
This bit is set by hardware when entering in interrupt or by software to disable all interrupts except
the TRAP software interrupt. This bit is cleared by
software.
0: Interrupts are enabled.
1: Interrupts are disabled.
This bit is controlled by the RIM, SIM and IRET instructions and is tested by the JRM and JRNM instructions.
Note: Interrupts requested while I is set are
latched and can be processed when I is cleared.
By default an interrupt routine is not interruptible
22/124
1
Bit 0 = C Carry/borrow.
This bit is set and cleared by hardware and software. It indicates an overflow or an underflow has
occurred during the last arithmetic operation.
0: No overflow or underflow has occurred.
1: An overflow or underflow has occurred.
This bit is driven by the SCF and RCF instructions
and tested by the JRC and JRNC instructions. It is
also affected by the “bit test and branch”, shift and
rotate instructions.
ST7LITE0xY0, ST7LITESxY0
CPU REGISTERS (Cont’d)
Stack Pointer (SP)
Read/Write
Reset Value: 00 FFh
15
0
8
0
0
0
0
0
0
7
1
0
0
1
SP5
SP4
SP3
SP2
SP1
SP0
The Stack Pointer is a 16-bit register which is always pointing to the next free location in the stack.
It is then decremented after data has been pushed
onto the stack and incremented before data is
popped from the stack (see Figure 12).
Since the stack is 64 bytes deep, the 10 most significant bits are forced by hardware. Following an
MCU Reset, or after a Reset Stack Pointer instruction (RSP), the Stack Pointer contains its reset value (the SP5 to SP0 bits are set) which is the stack
higher address.
The least significant byte of the Stack Pointer
(called S) can be directly accessed by a LD instruction.
Note: When the lower limit is exceeded, the Stack
Pointer wraps around to the stack upper limit, without indicating the stack overflow. The previously
stored information is then overwritten and therefore lost. The stack also wraps in case of an underflow.
The stack is used to save the return address during a subroutine call and the CPU context during
an interrupt. The user may also directly manipulate
the stack by means of the PUSH and POP instructions. In the case of an interrupt, the PCL is stored
at the first location pointed to by the SP. Then the
other registers are stored in the next locations as
shown in Figure 12.
– When an interrupt is received, the SP is decremented and the context is pushed on the stack.
– On return from interrupt, the SP is incremented
and the context is popped from the stack.
A subroutine call occupies two locations and an interrupt five locations in the stack area.
Figure 12. Stack Manipulation Example
CALL
Subroutine
PUSH Y
Interrupt
event
POP Y
RET
or RSP
IRET
@ 00C0h
SP
SP
CC
A
X
X
X
PCH
PCH
PCH
PCL
PCL
PCL
PCH
PCH
PCH
PCH
PCH
PCL
PCL
PCL
PCL
PCL
SP
@ 00FFh
SP
Y
CC
A
CC
A
SP
SP
Stack Higher Address = 00FFh
Stack Lower Address = 00C0h
23/124
1
ST7LITE0xY0, ST7LITESxY0
7 SUPPLY, RESET AND CLOCK MANAGEMENT
The device includes a range of utility features for
securing the application in critical situations (for
example in case of a power brown-out), and reducing the number of external components.
Main features
■
Clock Management
– 1 MHz internal RC oscillator (enabled by option byte)
– External Clock Input (enabled by option byte)
– PLL for multiplying the frequency by 4 or 8
(enabled by option byte)
■
Reset Sequence Manager (RSM)
■
System Integrity Management (SI)
– Main supply Low voltage detection (LVD) with
reset generation (enabled by option byte)
– Auxiliary Voltage detector (AVD) with interrupt
capability for monitoring the main supply (enabled by option byte)
7.1 INTERNAL RC OSCILLATOR ADJUSTMENT
The ST7 contains an internal RC oscillator with an
accuracy of 1% for a given device, temperature
and voltage. It must be calibrated to obtain the frequency required in the application. This is done by
software writing a calibration value in the RCCR
(RC Control Register).
Whenever the microcontroller is reset, the RCCR
returns to its default value (FFh), i.e. each time the
device is reset, the calibration value must be loaded in the RCCR. Predefined calibration values are
stored in EEPROM for 3.0 and 5V VDD supply voltages at 25°C, as shown in the following table.
Notes:
– See “ELECTRICAL CHARACTERISTICS” on
page 81. for more information on the frequency
and accuracy of the RC oscillator.
– To improve clock stability and frequency accuracy, it is recommended to place a decoupling capacitor, typically 100nF, between the VDD and
VSS pins as close as possible to the ST7 device.
24/124
1
RCCR
RCCR0
RCCR1
Conditions
VDD=5V
TA=25°C
fRC=1MHz
VDD=3.0V
TA=25°C
fRC=700KHz
ST7FLITE09
Address
ST7FLITE05/
ST7FLITES5
Address
1000h and
FFDEh
FFDEh
1001h andFFDFh
FFDFh
– These two bytes are systematically programmed
by ST, including on FASTROM devices. Consequently, customers intending to us e FASTROM
service must not use these two bytes.
– RCCR0 and RCCR1 calibration values will be
erased if the read-out protection bit is reset after
it has been set. See “Read out Protection” on
page 15.
Caution: If the voltage or temperature conditions
change in the application, the frequency may need
to be recalibrated.
Refer to application note AN1324 for information
on how to calibrate the RC frequency using an external reference signal.
7.2 PHASE LOCKED LOOP
The PLL can be used to multiply a 1MHz frequency from the RC oscillator or the external clock by 4
or 8 to obtain fOSC of 4 or 8 MHz. The PLL is enabled and the multiplication factor of 4 or 8 is selected by 2 option bits.
– The x4 PLL is intended for operation with VDD in
the 2.4V to 3.3V range
– The x8 PLL is intended for operation with VDD in
the 3.3V to 5.5V range
Refer to Section 15.1 for the option byte description.
If the PLL is disabled and the RC oscillator is enabled, then fOSC = 1MHz.
If both the RC oscillator and the PLL are disabled,
fOSC is driven by the external clock.
ST7LITE0xY0, ST7LITESxY0
Figure 13. PLL Output Frequency Timing
Diagram
LOCKED bit set
4/8 x
input
freq.
Bit 1 = MCO Main Clock Out enable
This bit is read/write by software and cleared by
hardware after a reset. This bit allows to enable
the MCO output clock.
0: MCO clock disabled, I/O port free for general
purpose I/O.
1: MCO clock enabled.
Output freq.
tSTAB
Bit 0 = SMS Slow Mode select
This bit is read/write by software and cleared by
hardware after a reset. This bit selects the input
clock fOSC or fOSC/32.
0: Normal mode (fCPU = fOSC
1: Slow mode (fCPU = fOSC/32)
tLOCK
tSTARTUP
t
When the PLL is started, after reset or wakeup
from Halt mode or AWUFH mode, it outputs the
clock after a delay of tSTARTUP.
When the PLL output signal reaches the operating
frequency, the LOCKED bit in the SICSCR register
is set. Full PLL accuracy (ACCPLL) is reached after
a stabilization time of tSTAB (see Figure 13 and
13.3.4 Internal RC Oscillator and PLL)
Refer to section 8.4.4 on page 36 for a description
of the LOCKED bit in the SICSR register.
7.3 REGISTER DESCRIPTION
MAIN CLOCK CONTROL/STATUS REGISTER
(MCCSR)
Read / Write
Reset Value: 0000 0000 (00h)
7
0
0
0
0
0
0
0
MCO
RC CONTROL REGISTER (RCCR)
Read / Write
Reset Value: 1111 1111 (FFh)
7
0
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
Bits 7:0 = CR[7:0] RC Oscillator Frequency Adjustment Bits
These bits must be written immediately after reset
to adjust the RC oscillator frequency and to obtain
an accuracy of 1%. The application can store the
correct value for each voltage range in EEPROM
and write it to this register at start-up.
00h = maximum available frequency
FFh = lowest available frequency
Note: To tune the oscillator, write a series of different values in the register until the correct frequency is reached. The fastest method is to use a dichotomy starting with 80h.
SMS
Bits 7:2 = Reserved, must be kept cleared.
Table 5. Clock Register Map and Reset Values
Address
(Hex.)
0038h
0039h
Register
Label
7
6
5
4
3
2
1
0
0
0
0
0
0
0
MCO
0
SMS
0
CR7
1
CR6
1
CR5
1
CR4
1
CR3
1
CR2
1
CR1
1
CR0
1
MCCSR
Reset Value
RCCR
Reset Value
25/124
1
ST7LITE0xY0, ST7LITESxY0
SUPPLY, RESET AND CLOCK MANAGEMENT (Cont’d)
Figure 14. Clock Management Block Diagram
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
RCCR
1MHz
8MHz
PLL 1MHz -> 8MHz
PLL 1MHz -> 4MHz
Tunable
1% RC Oscillator
Option byte
/2 DIVIDER
CLKIN
fOSC
4MHz
0 to 8 MHz
Option byte
8-BIT
LITE TIMER COUNTER
fOSC
fLTIMER
(1ms timebase @ 8 MHz fOSC)
fOSC/32
/32 DIVIDER
1
fCPU
fOSC
0
TO CPU AND
PERIPHERALS
(except LITE
TIMER)
MCO SMS MCCSR
7
26/124
1
0
fCPU
MCO
ST7LITE0xY0, ST7LITESxY0
7.4 RESET SEQUENCE MANAGER (RSM)
7.4.1 Introduction
The reset sequence manager includes three RESET sources as shown in Figure 16:
■ External RESET source pulse
■ Internal LVD RESET (Low Voltage Detection)
■ Internal WATCHDOG RESET
Note: A reset can also be triggered following the
detection of an illegal opcode or prebyte code. Refer to section 11.2.1 on page 53 for further details.
These sources act on the RESET pin and it is always kept low during the delay phase.
The RESET service routine vector is fixed at addresses FFFEh-FFFFh in the ST7 memory map.
The basic RESET sequence consists of 3 phases
as shown in Figure 15:
■ Active Phase depending on the RESET source
■ 256 CPU clock cycle delay
■ RESET vector fetch
The 256 CPU clock cycle delay allows the oscillator to stabilise and ensures that recovery has taken place from the Reset state.
The RESET vector fetch phase duration is 2 clock
cycles.
If the PLL is enabled by option byte, it outputs the
clock after an additional delay of tSTARTUP (see
Figure 13).
Figure 15. RESET Sequence Phases
RESET
Active Phase
INTERNAL RESET
256 CLOCK CYCLES
FETCH
VECTOR
Figure 16.Reset Block Diagram
VDD
RON
RESET
INTERNAL
RESET
FILTER
PULSE
GENERATOR
WATCHDOG RESET
ILLEGAL OPCODE RESET 1)
LVD RESET
Note 1: See “Illegal Opcode Reset” on page 78. for more details on illegal opcode reset conditions.
27/124
1
ST7LITE0xY0, ST7LITESxY0
RESET SEQUENCE MANAGER (Cont’d)
7.4.2 Asynchronous External RESET pin
The RESET pin is both an input and an open-drain
output with integrated RON weak pull-up resistor.
This pull-up has no fixed value but varies in accordance with the input voltage. It can be pulled
low by external circuitry to reset the device. See
Electrical Characteristic section for more details.
A RESET signal originating from an external
source must have a duration of at least th(RSTL)in in
order to be recognized (see Figure 17). This detection is asynchronous and therefore the MCU
can enter reset state even in HALT mode.
The RESET pin is an asynchronous signal which
plays a major role in EMS performance. In a noisy
environment, it is recommended to follow the
guidelines mentioned in the electrical characteristics section.
7.4.3 External Power-On RESET
If the LVD is disabled by option byte, to start up the
microcontroller correctly, the user must ensure by
means of an external reset circuit that the reset
signal is held low until VDD is over the minimum
level specified for the selected fOSC frequency.
A proper reset signal for a slow rising VDD supply
can generally be provided by an external RC network connected to the RESET pin.
7.4.4 Internal Low Voltage Detector (LVD)
RESET
Two different RESET sequences caused by the internal LVD circuitry can be distinguished:
■ Power-On RESET
■ Voltage Drop RESET
The device RESET pin acts as an output that is
pulled low when VDD
79/124
1
ST7LITE0xY0, ST7LITESxY0
INSTRUCTION GROUPS (cont’d)
Mnemo
Description
Function/Example
Dst
Src
JRULE
Jump if (C + Z = 1)
Unsigned