STD30NF06LT4

STD30NF06L N-CHANNEL 60V - 0.022Ω - 35A DPAK/IPAK STripFET™ POWER MOSFET TYPE STD30NF06L ■ ■ ■ ■ ■ ■ VDSS RDS(on) ID 60 V =15 V , ID =15 A Ciss Input Capacitance VDS = 25 V, f = 1 MHz, VGS = 0 Coss Output Capacitance Crss Reverse Transfer Capacitance Min. 25 S 1600 pF 215 pF 60 pF STD30NF06L ELECTRICAL CHARACTERISTICS (CONTINUED) SWITCHING ON Symbol td(on) tr Qg Qgs Qgd Parameter Turn-on Delay Time Rise Time Total Gate Charge Gate-Source Charge Gate-Drain Charge Test Conditions Min. VDD = 30 V, ID = 18 A RG = 4.7Ω VGS = 4.5 V (see test circuit, Figure 3) VDD = 48 V, ID = 38 A, VGS = 5 V Typ. Max. Unit 30 ns 105 ns 23 7 10 31 nC nC nC Typ. Max. Unit SWITCHING OFF Symbol td(off) tf Parameter Turn-off-Delay Time Fall Time Test Conditions Min. VDD = 30 V, ID = 18 A, RG = 4.7Ω, VGS = 4.5 V (see test circuit, Figure 3) 65 25 ns ns SOURCE DRAIN DIODE Symbol ISD ISDM (2) VSD (1) trr Qrr IRRM Max. Unit Source-drain Current Parameter 35 A Source-drain Current (pulsed) 140 A Forward On Voltage Reverse Recovery Time Reverse Recovery Charge Reverse Recovery Current Test Conditions Min. Typ. ISD = 35 A, VGS = 0 ISD = 38 A, di/dt = 100 A/µs, VDD = 15 V, Tj = 150°C (see test circuit, Figure 5) 1.5 70 140 4 V ns nC A Note: 1. Pulsed: Pulse duration = 300 µs, duty cycle 1.5 %. 2. Pulse width limited by safe operating area. Safe Operating Area Normalized Thermal Impedence 3/10 STD30NF06L Output Characteristics Transfer Characteristics Transconductance Static Drain-source On Resistance Gate Charge vs Gate-source Voltage Capacitance Variations 4/10 STD30NF06L Normalized Gate Threshold Voltage vs Temperature Normalized Drain-Source Breakdown vs Temperature Normalized On Resistance vs Temperature Source-drain Diode Forward Characteristics 5/10 STD30NF06L Fig. 1: Unclamped Inductive Load Test Circuit Fig. 2: Unclamped Inductive Waveform Fig. 3: Switching Times Test Circuit For Resistive Load Fig. 4: Gate Charge test Circuit Fig. 5: Test Circuit For Inductive Load Switching And Diode Recovery Times 6/10 STD30NF06L TO-251 (IPAK) MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. MIN. TYP. 2.4 0.086 MAX. 0.094 0.043 A 2.2 A1 0.9 1.1 0.035 A3 0.7 1.3 0.027 0.051 B 0.64 0.9 0.025 0.031 B2 5.2 5.4 0.204 0.212 B3 0.85 B5 0.033 0.3 0.012 B6 0.95 0.037 C 0.45 0.6 0.017 0.023 C2 0.48 0.6 0.019 0.023 D 6 6.2 0.236 0.244 E 6.4 6.6 0.252 0.260 G 4.4 4.6 0.173 0.181 H 15.9 16.3 0.626 0.641 L 9 9.4 0.354 0.370 L1 0.8 1.2 0.031 L2 0.8 0.047 1 0.031 0.039 A1 C2 A3 A C H B B3 = 1 = 2 G = = = E B2 = 3 B5 L D B6 L2 L1 0068771-E 7/10 STD30NF06L TO-252 (DPAK) MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 2.20 2.40 0.087 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.90 0.025 0.035 B2 5.20 5.40 0.204 0.213 C 0.45 0.60 0.018 0.024 C2 0.48 0.60 0.019 0.024 D 6.00 6.20 0.236 0.244 E 6.40 6.60 0.252 0.260 G 4.40 4.60 0.173 0.181 H 9.35 10.10 0.368 0.398 L2 0.8 0.031 L4 0.60 1.00 0.024 0.039 V2 0o 8o 0o 0o P032P_B 8/10 STD30NF06L DPAK FOOTPRINT TUBE SHIPMENT (no suffix)* All dimensions are in millimeters All dimensions are in millimeters TAPE AND REEL SHIPMENT (suffix ”T4”)* REEL MECHANICAL DATA DIM. mm MIN. A DIM. mm MIN. MAX. A0 6.8 7 0.267 0.275 B0 10.4 10.6 0.409 0.417 B1 D 1.5 D1 1.5 E 1.65 9/10 inch MIN. MAX. 12.1 0.476 1.6 0.059 0.063 0.059 1.85 0.065 0.073 F 7.4 7.6 0.291 0.299 K0 2.55 2.75 0.100 0.108 P0 3.9 4.1 0.153 0.161 P1 7.9 8.1 0.311 0.319 P2 1.9 2.1 0.075 0.082 R W 40 15.7 16.3 1.574 0.618 0.641 MIN. 330 B 1.5 C 12.8 D 20.2 G 16.4 N 50 T TAPE MECHANICAL DATA MAX. inch MAX. 12.992 0.059 13.2 0.504 0.520 0.795 18.4 0.645 0.724 1.968 22.4 0.881 BASE QTY BULK QTY 2500 2500 STD30NF06L Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 10/10