STEVAL-CBL012V1
Dual LNB supply and control IC DiSEqC 2.0 compliant based on
the LNBH26
Data brief
•
•
•
•
•
Low-drop post regulator and high-efficiency
step-up PWM with integrated power N-MOS
allowing low power losses
LPM function (low-power mode) to reduce
dissipation
Overload and overtemperature internal
protection with I²C diagnostic bits
LNB short-circuit dynamic protection
RoHS compliant
Description
Features
•
•
•
•
•
•
Complete interface between LNB and I²C
bus
Built-in DC-DC converter for single 12 V
supply operation and high efficiency (typ.
93% @ 0.5 A)
Selectable output current limit using an
external resistor
Compliant with main satellite receiver output
voltage specifications (15 programmable
levels)
Accurate built-in 22 kHz tone generator suits
widely-accepted standards
22 kHz tone waveform integrity guaranteed
also at no load
January 2014
This product evaluation board implements a DCDC converter based on the LNBH26 device used
to power LNBs inside dish antennas which
receive satellite TV signals. The LNBH26 is an
integrated solution for supplying/interfacing
satellite LNB modules in accordance with
international standards, offering a complete
solution for dual-tuner satellite receivers and
good performance at low cost using few external
components. The LNBH26 evaluation board
2
includes an I C bus interface and the internal
22 kHz tone generator (factory trimmed) is
controlled by the DSQIN pin (TTL compatible),
permitting immediate DiSEqC™ data encoding. A
fully integrated step-up DC-DC converter allows
operation with a single input voltage supply
source ranging from 8 V to 16 V.
DocID025826 Rev 1
For further information contact your local STMicroelectronics sales
office
1/4
www.st.com
Schematic
1
STEVAL-CBL012V1
Schematic
Figure 1: STEVAL-CBL012V1 schematic
2/4
DocID025826 Rev 1
STEVAL-CBL012V1
2
Revision history
Revision history
Table 1: Revision history
Date
Revision
29-Jan-2014
1
DocID025826 Rev 1
Changes
Initial release
3/4
STEVAL-CBL012V1
Please Read Carefully
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or
services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third
party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR
IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR
EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS
LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY
REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR
(D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE,
THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR
"AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL" INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN
SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN
AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2014 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4
DocID025826 Rev 1
很抱歉,暂时无法提供与“STEVAL-CBL012V1”相匹配的价格&库存,您可以联系我们找货
免费人工找货