STEVAL-CCA016V1
Filter-free stereo 2.8 W Class-D audio power amplifier
demo board with selectable 3D sound effects based on the TS4999
Data brief
Features
■
Operating range from VCC= 2.4 V to 5.5 V
■
Dedicated standby mode active low for each
channel
■
Output power per channel: 2.8 W at 5 V into 4
Ω with 10% THD+N
■
Output power per channel: 0.7 W at 3.6 V into
8 Ω with 1% THD+N max.
■
Selectable 3D sound effect
■
Four gain setting steps: 3.5, 6, 9.5 and 12 dB.
■
Low current consumption
■
PSRR: 63 dB typ @ 217 Hz.
■
Fast start-up phase: 7.8 ms
■
Output short-circuit and thermal shutdown
protection
■
RoHS compliant
STEVAL-CCA016V1
Description
This demonstration board is designed to evaluate
the performances of TS4999, that is a stereo fully
differential Class-D power amplifier.
It can drive up to 1.35 W into a 8 Ω load at 5 V per
channel. The device has four different gain
settings utilizing two discrete pins, G0 and G1.
Pop and click reduction circuitry provides low
on/off switch noise while allowing the device to
start within 8 ms.
3D enhancement effects are selected through
one digital input pin that allows more amazing
stereo audio sound.
Two standby pins (active low) allow each channel
to be switched off separately.
The TS4999 is available in a 18 bumps Flip-Chip
package.
June 2009
Doc ID 15864 Rev 1
For further information contact your local STMicroelectronics sales office.
1/5
www.st.com
5
Circuit schematic and BOM list
STEVAL-CCA016V1
1
Circuit schematic and BOM list
Figure 1.
Schematic diagram
Vcc
P1
Vcc
GND
LinLin+
GND
1
2
VCC
3
1
4
3
2
1
C5
100nF
3D
C6
1uF
D6
U1
220nF
C2
D4
C1
C1
AVCC
RPVCC
C7
1uF
B6
2
JP1
Vcc
S5
3D
LPVCC
JP3
LinP
220nF
A1
Lin+
B2
Lin-
G0
C3
G0
G1
C5
G1
E1
Rin+
LinN
Lout+
A5
Lout-
A7
H
Gain
PWM
Select
Bridge
3 S1
VCC
1
G0
3 S2
2
VCC
Header 4
3D EFFECT
2
Oscillator
1
G1
1
2
3
4
JP4
RinP
D2
Rin-
A3
STBYL
STBR E3
STBYR
RinN
Rout+
E5
Bridge Rout-
E7
H
Gain
PWM
Select
C3
1
2
3
4
Header 4
STBL
Standby
Control
TS4999 - FC18
PGND
1
3
1
S4
STBR
JP2
3
1
2
3
4
S3
STBL
C7
AGND
2
2
220nF
Protection
Circuit
B4
220nF
C4
GND
Rin+
RinGND
VCC
Table 1.
VCC
Components list for the demonstration board
Designation
Quantity
Description
C1, C2, C3, C4
4
220 nF/16 V, SMD ceramic capacitor, 0603
C5
1
100 nF/16 V, SMD ceramic capacitor, 0603
C6, C7
1
1 µF/16 V, SMD ceramic capacitor, 0603
P1
1
2-pin header 2.54 mm pitch
S1, S2, S3, S4, S5
5
3-pin header 2.54 mm pitch
JP1, JP2, JP3, JP4
4
4-pin header 2.54 mm pitch
U1
1
TS4999 class-D audio amplifier
2/5
Doc ID 15864 Rev 1
STEVAL-CCA016V1
2
Demonstration board layouts
Demonstration board layouts
The following figures depict the top view and layers of the demonstration board.
Figure 2.
PCB top layer
Figure 3.
PCB middle layer 1
Figure 4.
PCB middle layer 2
Figure 5.
PCB bottom layer
Doc ID 15864 Rev 1
3/5
Revision history
3
STEVAL-CCA016V1
Revision history
Table 2.
4/5
Document revision history
Date
Revision
11-Jun-2009
1
Changes
Initial release.
Doc ID 15864 Rev 1
STEVAL-CCA016V1
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 15864 Rev 1
5/5