STEVAL-IHM032V1

STEVAL-IHM032V1 150 W inverter featuring the L639x and STGD3HF60HD for 1-shunt based sinusoidal vector control and trapezoidal scalar control Features ■ Compact size ■ Wide-range input voltage ■ Maximum power up to 150 W at 230 Vac input ■ STGD3HF60HD: 4.5 A, 600 V very fast IGBT ■ Compatibility with other power switches in DPAK packages (the STD5N52U and STGD6NC60HD, for example) ■ AC or DC bus voltage power supply connectors ■ Connector for interfacing with the STM3210xxEVAL board, STEVAL-IHM022V1, and STEVAL-IHM033V1 with alternate functions (current reference, current limitation/regulation, method selection, current boost) ■ Efficient DC/DC power supply (15 V, 3.3 V) ■ Suitable both for sinusoidal FOC and trapezoidal BLDC drive ■ Single-shunt current reading topology with fast operational amplifier (with offset insertion for bipolar currents) ■ Hardware overcurrent protection with boost capabilities ■ Temperature sensor ■ BEMF-detection network for BLDC drive ■ Current regulation/limitation network for BLDC drive ■ Hall sensor/quadrature encoder inputs Applications ■ Dishwasher pumps ■ Refrigerator compressors ■ Fans October 2011 STEVAL-IHM032V1 Description The STEVAL-IHM032V1 demonstration board is a 3-phase inverter designed to perform both the field-oriented control (FOC) of sinusoidal-shaped back-EMF permanent magnet synchronous motors (PMSMs) and trapezoidal control of brushless DC (BLDC) motors with or without sensors, with nominal power up to 150 W. This flexible, open, high-performance system based on the L639x and STGD3HF60HD is specifically designed to achieve fast and accurate conditioning of the current feedback, thereby matching the requirements typical of high-end applications such as field-oriented motor control. The board is compatible with 110 and 230 Vac mains, and includes a power supply stage with the VIPer12A-E (in flyback configuration) to generate the +15 V and +3.3 V supply voltage required by the application. Finally, the board can be interfaced through a dedicated connector with the STM3210xx-EVAL (STM32 microcontroller demonstration board), STEVAL-IHM022V1 (highdensity, dual motor control demonstration board based on the STM32F103ZE microcontroller), and with the STEVAL-IHM033V1 (control stage based on the STM32F100 microcontroller suitable for motor control). Doc ID 022402 Rev 1 1/4 www.st.com 4 Schematic STEVAL-IHM032V1 Schematic Figure 1. Internal schematic R5 Vbus D1 1N4148 10 2 1 Q1 STGD3HF60HDT4 1 1 2 3 4 5 6 7 PhaseU_H +15V LIN BOOT SD HVG HIN OUT VCC NC DT LVG OPOUT OPGND OP+ C9 470nF 14 13 12 11 10 9 8 C8 R6 2.2uF 100 3 U2 Phase A D3 1N4148 R12 10 R13 100 2 PhaseU_L Q3 STGD3HF60HDT4 1 MOTOR 3 L6392D STMicroelectronics and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. STMicroelectronics and/or its licensors do not warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. STMicroelectronics and/or its licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application. CUR_OP- Curr feedback Emergency CON3 R74 N.M. Vbus C12 N.M. R14 D4 1N4148 10 470nF C10 C11 R15 2.2uF 100 Phase B D6 1N4148 R21 10 R23 100 Q6 STGD3HF60HDT4 1 L6391D R25 1k Vdd_Micro Vdd_Micro R69 4.7k R70 910 1 3 R26 22 C14 2.2nF CUR_OP+ +15V C17 470nF C16 R36 2.2uF 100 Phase C R41 D8 1N4148 10 R43 100 R64 BLDC ETR 10k Q9 STGD3HF60HDT4 1 3 L6392D 14 13 12 11 10 9 8 Curr feedback J17 1 Temperature feedback 3 LIN BOOT SD HVG HIN OUT VCC NC DT LVG OPOUT OPGND OP+ 2 U4 1 2 3 4 5 6 7 PhaseW_H R59 2.7k 2 Q7 STGD3HF60HDT4 1 PhaseW_L R34 2.7k 2 D7 1N4148 10 CUR_OPR60 5.6k C15 33pF Vbus R35 R28 22 R33 1k OC Boost C46 4.7nF R31 1k 910 C13 22nF R66 10k R67 2k J16 R29 R32 R63 R71 R72 1.8 1.8 1.8 1.8 R30 1k R27 2.2k +3.3V +5V 2 R73 N.M. Vdd_Micro GND 3 14 13 12 11 10 9 8 GND 2 PhaseV_H +15V LIN BOOT SD/OD HVG HIN OUT VCC NC_11 DT LVG NC_6 CP+ GND CP- 3 1 2 3 4 5 6 7 GND Q4 STGD3HF60HDT4 1 U3 PhaseV_L Phase C Phase B Phase A J12 2 Q10 N.M. GND 1 2 3 CUR_OP+ Vdd_Micro NTC2 NTC 10k C37 10nF R68 4.7k RS model C621/1206 Placed near the IGBT bridge BLDC Curr ref. R3 10M C7 4.7nF Curr feedback AM10125V1 2/4 Doc ID 022402 Rev 1 STEVAL-IHM032V1 2 Revision history Revision history Table 1. Document revision history Date Revision 25-Oct-2011 1 Changes Initial release. Doc ID 022402 Rev 1 3/4 STEVAL-IHM032V1 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2011 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 4/4 Doc ID 022402 Rev 1