STEVAL-ISA188V1

STEVAL-ISA188V1 38 V, 1.5 A synchronous step-down switching regulator evaluation board based on A6986F3V3 Data brief Description Features                    AECQ100 qualification 1.5 A DC output current 4 V to 38 V operating input voltage Low consumption mode or low noise mode Programmable ISKIP current 30 μA IQ at light load (LCM VIN = 12 V) 8 μA IQ-SHTDWN Adjustable f SW (250 kHz - 2 MHz) Fixed output voltage VOUT= 3.3 V Embedded output voltage supervisor Synchronization Adjustable soft-start time Internal current limiting Overvoltage protection Output voltage sequencing Peak current mode architecture RDS(on)HS = 180 mΩ; RDS(on)LS = 150 mΩ Thermal shutdown RoHS compliant February 2016 The STEVAL-ISA188V1 is a product evaluation board based on the ST synchronous step-down switching regulator A6986F3V3, which can deliver up to 1.5 A and, with its 100% duty cycle ability to withstand cold crank events and wide input operating voltage range, represents the ideal choice for battery-powered automotive systems. Synchronous rectification helps achieve higher efficiency at full load as well as application compactness, while high-frequency switching (programmable up to 2 MHz) helps reduce the cost and size of power passive components while remaining outside the AM band. The device can operate in low consumption mode (LCM), with a quiescent current of 30 μA that ensures high efficiency under light load, which is a requirement in typical car body applications that are active when a car is parked. A low noise mode (LNM) can be selected to meet the requirements of infotainment applications with forced PWM mode under all load conditions. The default board configuration is LCM active, 500 kHz switching frequency, high ISKIP current and the switchover feature enabled, but all of these settings can be easily changed so the user can evaluate different application scenarios. DocID028953 Rev 1 For further information contact your local STMicroelectronics sales office 1/4 www.st.com VIN_FLT NM GND VIN TP6 TP5 PGND + L3 J4 MPZ2012S221A + TP3 4.7uF C16 C13A NM C13 4.7uF C15 SYNCH 10uF C1 50V 1uF C2 TP1 470nF 4.7uH NM L2 PGND VIN_FLT R2 NM 0 R1 C3 NM R3 C11 J5 4.7uF DocID028953 Rev 1 C14 J1 10nF 17 EP DELAY SS/INH MLF FSW VCC VIN SYNCH 68nF 8 3 6 5 2 15 4 U1 C6 NM 10R C5 VIN_EMI TP8 R4 0R R10 R11 10 SGND R5 11 12 PGND PGND COMP FB LX LX VBIAS RST A6986F3V3 NM 7 9 13 14 16 1 R8 220p power GND signal GND 2.2p 75k C8 C4 J2 R9 NM L1A L1 R6 R7 C7 NM 6.8uH J3 1M 0R NM 10uF C9 2/4 10uF TP7 TP4 TP2 GND VOUT RST 1 C10 SS/INH Schematic diagram STEVAL-ISA188V1 Schematic diagram Figure 1: STEVAL-ISA188V1 schematic circuit GSPG02022016DI1510 STEVAL-ISA188V1 2 Revision history Revision history Table 1: Document revision history Date Version Changes 02-Feb-2016 1 Initial release. DocID028953 Rev 1 3/4 STEVAL-ISA188V1 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved 4/4 DocID028953 Rev 1