STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
10 A, 600 V short-circuit rugged IGBT
Datasheet - production data
Features
Lower on voltage drop (VCE(sat))
Lower CRES / CIES ratio (no cross-conduction
susceptibility)
Very soft ultra fast recovery antiparallel
diode
Short-circuit withstand time 10 μs
Applications
High frequency motor controls
SMPS and PFC in both hard switch and
resonant topologies
Motor drives
Figure 1: Internal schematic diagram
Description
These devices are very fast IGBTs developed
using advanced PowerMESH™ technology. This
process guarantees an excellent trade-off
between switching performance and low on-state
behavior. These devices are well-suited for
resonant or soft-switching applications.
Table 1: Device summary
Order code
Marking
Package
STGB10NC60KDT4
GB10NC60KD
D²PAK
STGD10NC60KDT4
GD10NC60KD
DPAK
STGF10NC60KD
GF10NC60KD
TO-220FP
STGP10NC60KD
GP10NC60KD
TO-220
June 2017
DocID11423 Rev 7
This is information on a product in full production.
Packing
Tape and reel
Tube
1/30
www.st.com
Contents
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Contents
1
Electrical ratings ............................................................................. 3
2
Electrical characteristics ................................................................ 4
2.1
Electrical characteristics (curves) ...................................................... 7
3
Test circuits ................................................................................... 10
4
Package information ..................................................................... 11
5
2/30
4.1
D²PAK (TO-263) type A package information ................................. 11
4.2
D²PAK (TO-263) type B package information ................................. 14
4.3
DPAK (TO-252) type A package information................................... 17
4.4
TO-220FP package information ...................................................... 20
4.5
TO-220 type A package information................................................ 22
4.6
D²PAK (TO-263) type A packing information .................................. 24
4.7
D²PAK (TO-263) type B packing information .................................. 26
4.8
DPAK (TO-252) type A tape packing information ............................ 27
Revision history ............................................................................ 29
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
1
Electrical ratings
Electrical ratings
Table 2: Absolute maximum ratings
Value
Symbo
l
VCES
Parameter
Unit
D²PAK,
TO-220
DPAK
Collector-emitter voltage (VGE = 0 V)
IC(1)
TO-220FP
600
V
Continuous collector current at TC = 25 °C
20
9
A
Continuous collector current at TC = 100 °C
10
6
A
(2)
Turn-off latching current
30
A
ICP(3)
Pulsed collector current
30
A
VGE
Gate-emitter voltage
±20
V
Diode RMS forward current at Tc=25°C
10
A
IFSM
Surge non repetitive forward current tp = 10
ms sinusoidal
20
A
PTOT
Total dissipation at TC = 25 °C
VISO
Insulation withstand voltage (RMS) from all
three leads to external heat sink
(t=1 s;TC=25 °C)
tscw
Short-circuit withstand time VCE = 0.5 VCES,
Tj = 125 °C, RG = 10 Ω, VGE = 12 V
Tstg
Storage temperature range
TJ
Operating junction temperature range
ICL
IF
62
65
25
W
2500
V
10
μs
- 55 to 150
°C
Notes:
(1)Calculated
(2)V
= 80 % VCES, VGE = 15 V, RG = 10 Ω, TJ = 150 °C.
clamp
(3)Pulse
according to the iterative formula:
width limited by maximum junction temperature and turn-off within RBSOA.
Table 3: Thermal data
Value
Symbol
Parameter
Unit
TO-220, D²PAK
DPAK
TO-220FP
Rthj-case
Thermal resistance junction-case IGBT
1.9
2
5
Rthj-case
Thermal resistance junction-case diode
4
4.5
7
Rthj-amb
Thermal resistance junction-ambient
62.5
100
62.5
DocID11423 Rev 7
°C/W
3/30
Electrical characteristics
2
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Electrical characteristics
TC = 25 °C unless otherwise specified
Table 4: Static characteristics
Symbol
Parameter
Test conditions
V(BR)CES
Collector-emitter breakdown
voltage
VCE(sat)
Collector-emitter saturation
voltage
VGE(th)
Gate threshold voltage
ICES
Collector cut-off current
IGES
Gate-emitter leakage
current
VGE = ±20 V
gfs(2)
Forward transconductance
VCE = 15 V, IC= 5 A
IC = 1 mA, VGE = 0 V
Min.
Typ.
600
Unit
V
VGE =15 V, IC = 5 A
2.2
VGE = 15 V, IC = 5 A,
Tj= 125 °C
1.8
VCE = VGE, IC = 250 µA
Max.
4.5
2.5
V
6.5
V
VCE = 600 V, VGE = 0 V
150
µA
VCE=600 V, VGE = 0 V,
Tj = 125 °C (1)
1
mA
±100
nA
15
S
Notes:
(1)Defined
(2)Pulse
by design, not subject to production test.
test: pulse duration < 300 μs, duty cycle < 2 %.
Table 5: Dynamic characteristics
Symbol
4/30
Parameter
Cies
Input capacitance
Coes
Output capacitance
Cres
Reverse transfer
capacitance
Qg
Total gate charge
Qge
Gate-emitter charge
Qgc
Gate-collector charge
Test conditions
VCE= 25 V, f = 1 MHz,
VGE = 0 V
VCE = 390 V, IC = 5 A,
VGE = 0 to 15 V
(see Figure 19: " Gate charge
test circuit")
DocID11423 Rev 7
Min.
Typ.
Max.
-
380
-
-
46
-
-
8.5
-
-
19
-
-
5
-
-
9
-
Unit
pF
nC
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Electrical characteristics
Table 6: Switching on/off (inductive load)
Symbol
td(on)
tr
(di/dt)on
td(on)
tr
(di/dt)on
Parameter
Turn-on delay time
Current rise time
Turn-on current slope
Turn-on delay time
Current rise time
Turn-on current slope
tr(Voff)
Off voltage rise time
td(off)
Turn-off delay time
tf
Current fall time
tr(Voff)
Off voltage rise time
td(off)
Turn-off delay time
tf
Test conditions
Current fall time
Min.
Typ.
Max.
Unit
VCC = 390 V, IC = 5 A,
RG = 10 Ω , VGE = 15 V
(see Figure 18: " Test circuit
for inductive load switching"
and Figure 20: " Switching
waveform")
-
17
-
ns
-
6
-
ns
-
655
-
A/µs
VCC = 390 V, IC = 5 A,
RG = 10 Ω , VGE = 15 V,
Tj=125°C
(see Figure 18: " Test circuit
for inductive load switching"
and Figure 20: " Switching
waveform")
-
16.5
-
ns
-
6.5
-
ns
-
575
-
A/µs
VCC = 390 V, IC = 5 A,
RG = 10 Ω, VGE = 15 V
(see Figure 18: " Test circuit
for inductive load switching"
and Figure 20: " Switching
waveform")
-
33
-
ns
-
72
-
ns
-
82
-
ns
VCC = 390 V, IC = 5 A,
RG = 10 Ω, VGE = 15 V,
Tj=125 °C
(see Figure 18: " Test circuit
for inductive load switching"
and Figure 20: " Switching
waveform")
-
60
-
ns
-
106
-
ns
-
136
-
ns
Test conditions
Min.
Typ.
Max.
Unit
VCC = 390 V, IC = 5 A,
RG = 10 Ω , VGE = 15 V
(see Figure 18: " Test circuit
for inductive load switching")
-
55
-
μJ
-
85
-
μJ
-
140
-
μJ
VCC = 390 V, IC = 5 A,
RG = 10 Ω , VGE = 15 V,
Tj=125°C
(see Figure 18: " Test circuit
for inductive load switching")
-
87
-
μJ
-
162
-
μJ
-
249
-
μJ
Table 7: Switching energy (inductive load)
Symbol
Parameter
Eon(1)
Turn-on switching energy
Eoff(2)
Turn-off switching energy
Ets
Total switching energy
Eon(1)
Turn-on switching energy
Eoff(2)
Turn-off switching energy
Ets
Total switching energy
Notes:
(1)Including
the reverse recovery of the diode.
(2)Including
the tail of the collector current.
DocID11423 Rev 7
5/30
Electrical characteristics
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Table 8: Collector-emitter diode
Symbol
6/30
Parameter
VF
Forward on-voltage
Test conditions
trr
Reverse recovery time
Qrr
Reverse recovery charge
Irrm
Reverse recovery current
trr
Reverse recovery time
Qrr
Reverse recovery charge
Irrm
Reverse recovery current
Min.
Typ.
Max.
Unit
IF=5 A
-
2
-
V
IF=5 A, Tj=125 °C
-
1.6
-
V
-
22
-
ns
-
14
-
nC
-
1.3
-
A
-
35
-
ns
-
40
-
nC
-
2.2
-
A
IF=5 A, VR=40 V, di/dt=100
A/μs (see Figure 21: " Diode
reverse recovery waveform")
IF=5 A, VR=40 V, Tj=125 °C,
di/dt=100 A/μs (see Figure
21: " Diode reverse recovery
waveform")
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
2.1
Electrical characteristics
Electrical characteristics (curves)
Figure 2: Output characteristics
Figure 3: Transfer characteristics
Figure 4: Transconductance
Figure 5: Collector-emitter on voltage vs
temperature
Figure 6: Collector-emitter on voltage vs
temperature
DocID11423 Rev 7
Figure 7: Capacitance variations
7/30
Electrical characteristics
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Figure 8: Normalized gate threshold voltage vs
temperature
Figure 9: Collector-emitter on voltage vs collector
current
Figure 10: Normalized breakdown voltage vs
temperature
Figure 11: Switching energy vs temperature
Figure 12: Switching energy vs gate resistance
8/30
Figure 13: Switching energy vs collector current
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Electrical characteristics
Figure 14: Thermal impedance for D²PAK, DPAK
and TO-220
Figure 15: Turn-off SOA
Figure 16: Emitter-collector diode characteristics
Figure 17: Thermal impedance for TO-220FP
DocID11423 Rev 7
9/30
Test circuits
3
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Test circuits
Figure 18: Test circuit for inductive load
switching
C
A
Figure 19: Gate charge test circuit
A
L=100 µH
G
E
B
B
3.3
µF
C
G
+
RG
VCC
1000
µF
D.U.T
E
-
AM01504v 1
Figure 20: Switching waveform
Figure 21: Diode reverse recovery waveform
di/dt
Qrr
trr
IF
ts
tf
t
IRRM
10%
IRRM
VRRM
dv/dt
AM01507v1
10/30
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
4
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
4.1
D²PAK (TO-263) type A package information
Figure 22: D²PAK (TO-263) type A package outline
DocID11423 Rev 7
11/30
Package information
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Table 9: D²PAK (TO-263) type A package mechanical data
mm
Dim.
Min.
Max.
A
4.40
4.60
A1
0.03
0.23
b
0.70
0.93
b2
1.14
1.70
c
0.45
0.60
c2
1.23
1.36
D
8.95
9.35
D1
7.50
7.75
8.00
D2
1.10
1.30
1.50
E
10.00
E1
8.50
8.70
8.90
E2
6.85
7.05
7.25
e
10.40
2.54
e1
4.88
5.28
H
15.00
15.85
J1
2.49
2.69
L
2.29
2.79
L1
1.27
1.40
L2
1.30
1.75
R
V2
12/30
Typ.
0.40
0°
DocID11423 Rev 7
8°
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Package information
Figure 23: D²PAK (TO-263) type A recommended footprint (dimensions are in mm)
DocID11423 Rev 7
13/30
Package information
4.2
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
D²PAK (TO-263) type B package information
Figure 24: D²PAK (TO-263) type B package outline
0079457_23_B
14/30
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Package information
Table 10: D²PAK (TO-263) type B mechanical data
mm
Dim.
Min.
Typ.
Max.
A
4.36
4.56
A1
0
0.25
b
0.70
0.90
b1
0.51
0.89
b2
1.17
1.37
b3
1.36
1.46
c
0.38
0.694
c1
0.38
0.534
c2
1.19
1.34
D
8.60
9.00
D1
6.90
7.50
E
10.15
10.55
E1
8.10
e
8.70
2.54 BSC
H
15.00
15.60
L
1.90
2.50
L1
1.65
L2
1.78
L3
L4
0.25
4.78
DocID11423 Rev 7
5.28
15/30
Package information
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Figure 25: D²PAK (TO-263) type B recommended footprint (dimensions are in mm)
16/30
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
4.3
Package information
DPAK (TO-252) type A package information
Figure 26: DPAK (TO-252) type A package outline
DocID11423 Rev 7
17/30
Package information
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Table 11: DPAK (TO-252) type A mechanical data
mm
Dim.
Min.
Max.
A
2.20
2.40
A1
0.90
1.10
A2
0.03
0.23
b
0.64
0.90
b4
5.20
5.40
c
0.45
0.60
c2
0.48
0.60
D
6.00
6.20
D1
4.95
E
6.40
E1
4.60
4.70
4.80
e
2.16
2.28
2.40
e1
4.40
4.60
H
9.35
10.10
L
1.00
1.50
(L1)
2.60
2.80
3.00
L2
0.65
0.80
0.95
L4
0.60
R
V2
18/30
Typ.
5.10
5.25
6.60
1.00
0.20
0°
DocID11423 Rev 7
8°
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Package information
Figure 27: DPAK (TO-252) type A recommended footprint (dimensions are in mm)
DocID11423 Rev 7
19/30
Package information
4.4
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
TO-220FP package information
Figure 28: TO-220FP package outline
7012510_Rev_12_B
20/30
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Package information
Table 12: TO-220FP package mechanical data
mm
Dim.
Min.
Typ.
Max.
A
4.4
4.6
B
2.5
2.7
D
2.5
2.75
E
0.45
0.7
F
0.75
1
F1
1.15
1.70
F2
1.15
1.70
G
4.95
5.2
G1
2.4
2.7
H
10
10.4
L2
16
L3
28.6
30.6
L4
9.8
10.6
L5
2.9
3.6
L6
15.9
16.4
L7
9
9.3
Dia
3
3.2
DocID11423 Rev 7
21/30
Package information
4.5
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
TO-220 type A package information
Figure 29: TO-220 type A package outline
22/30
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Package information
Table 13: TO-220 type A package mechanical data
mm
Dim.
Min.
Typ.
Max.
A
4.40
4.60
b
0.61
0.88
b1
1.14
1.55
c
0.48
0.70
D
15.25
D1
15.75
1.27
E
10.00
10.40
e
2.40
2.70
e1
4.95
5.15
F
1.23
1.32
H1
6.20
6.60
J1
2.40
2.72
L
13.00
14.00
L1
3.50
3.93
L20
16.40
L30
28.90
øP
3.75
3.85
Q
2.65
2.95
DocID11423 Rev 7
23/30
Package information
4.6
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
D²PAK (TO-263) type A packing information
Figure 30: D2PAK type A tape outline
24/30
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Package information
Figure 31: D2PAK type A reel outline
Table 14: D²PAK type A tape and reel mechanical data
Tape
Reel
mm
mm
Dim.
Dim.
Min.
Max.
Min.
A0
10.5
10.7
A
B0
15.7
15.9
B
1.5
Max.
330
D
1.5
1.6
C
12.8
D1
1.59
1.61
D
20.2
E
1.65
1.85
G
24.4
F
11.4
11.6
N
100
K0
4.8
5.0
T
P0
3.9
4.1
P1
11.9
12.1
Base quantity
1000
P2
1.9
2.1
Bulk quantity
1000
R
50
T
0.25
0.35
W
23.7
24.3
DocID11423 Rev 7
13.2
26.4
30.4
25/30
Package information
4.7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
D²PAK (TO-263) type B packing information
Figure 32: D2PAK type B tape outline
Figure 33: D2PAK type B reel outline
26/30
DocID11423 Rev 7
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Package information
Table 15: D²PAK type B reel mechanical data
mm
Dim.
Min.
A
330
B
1.5
C
12.8
D
20.2
G
24.4
N
100
T
4.8
Max.
13.2
26.4
30.4
DPAK (TO-252) type A tape packing information
Figure 34: DPAK (TO-252) tape outline
DocID11423 Rev 7
27/30
Package information
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
Figure 35: DPAK (TO-252) reel outline
Table 16: DPAK (TO-252) tape and reel mechanical data
Tape
Reel
mm
mm
Dim.
Dim.
Min.
Max.
A0
6.8
7
A
B0
10.4
10.6
B
1.5
12.1
C
12.8
1.6
D
20.2
G
16.4
50
B1
28/30
Min.
Max.
330
13.2
D
1.5
D1
1.5
E
1.65
1.85
N
F
7.4
7.6
T
K0
2.55
2.75
P0
3.9
4.1
Base qty.
2500
P1
7.9
8.1
Bulk qty.
2500
P2
1.9
2.1
R
40
T
0.25
0.35
W
15.7
16.3
DocID11423 Rev 7
18.4
22.4
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
5
Revision history
Revision history
Table 17: Document revision history
Date
Revision
Changes
14-Jun-2005
1
First release.
19-Jul-2005
2
Complete version.
27-Jan-2006
3
Inserted ecopack indication.
01-Mar-2006
4
The document has been reformatted.
08-Feb-2007
5
Modified value on Table 6.: Switching on/off (inductive load).
24-Nov-2009
6
Inserted DPAK package option.
06-Jun-2017
7
Modified part numbers on cover page.
Updated Section 4: "Package information".
Minor text changes.
DocID11423 Rev 7
29/30
STGB10NC60KDT4, STGD10NC60KDT4,
STGF10NC60KD, STGP10NC60KD
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST
products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the
design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2017 STMicroelectronics – All rights reserved
30/30
DocID11423 Rev 7