STGW30NC60WD
30 A, 600 V ultra fast IGBT
Features
■
High frequency operation
■
Lower CRES / CIES ratio (no cross-conduction
susceptibility)
■
Very soft ultra fast recovery antiparallel diode
Applications
2
■
High frequency motor controls, inverters, UPS
■
HF, SMPS and PFC in both hard switch and
resonant topologies
3
1
TO-247
Description
This IGBT utilizes the advanced Power MESH™
process resulting in an excellent trade-off
between switching performance and low on-state
behavior.
Table 1.
Figure 1.
Internal schematic diagram
Device summary
Order code
Marking
Package
Packaging
STGW30NC60WD
GW30NC60WD
TO-247
Tube
November 2008
Rev 5
1/14
www.st.com
14
Contents
STGW30NC60WD
Contents
1
Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1
Electrical characteristics (curves)
............................. 7
3
Test circuit
4
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2/14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
STGW30NC60WD
1
Electrical ratings
Electrical ratings
Table 2.
Absolute maximum ratings
Symbol
Value
Unit
VCES
Collector-emitter voltage (VGE = 0)
600
V
IC (1)
Collector current (continuous) at 25 °C
60
A
IC (1)
Collector current (continuous) at 100 °C
30
A
ICP(2)
Collector current (pulsed)
150
A
ICL (3)
Turn-off latching current
150
A
Gate-emitter voltage
± 20
V
Diode RMS forward current at TC = 25 °C
30
A
IFSM
Surge not repetitive forward current tp= 10 ms sinusoidal
120
A
PTOT
Total dissipation at TC = 25 °C
200
W
Tstg
Storage temperature
– 55 to 150
°C
Value
Unit
Thermal resistance junction-case IGBT max.
0.63
°C/W
Thermal resistance junction-case diode max.
1.5
°C/W
Thermal resistance junction-ambient max.
50
°C/W
VGE
IF
Tj
1.
Parameter
Operating junction temperature
Calculated according to the iterative formula:
T j ( max ) – T C
I C ( T C ) = --------------------------------------------------------------------------------------------------------R thj – c × V CE ( sat ) ( max ) ( T j ( max ), I C ( T C ) )
2. Pulse width limited by max junction temperature
3. VCLAMP = 80% (VCES), VGE = 15 V, RG = 10 Ω, TJ = 150 °C
Table 3.
Symbol
Rthj-case
Rthj-amb
Thermal resistance
Parameter
3/14
Electrical characteristics
2
STGW30NC60WD
Electrical characteristics
(TCASE = 25 °C unless otherwise specified)
Table 4.
Symbol
Static electrical characteristics
Parameter
Collector-emitter
V(BR)CES breakdown voltage
(VGE = 0)
IC = 1 mA
VCE(sat)
Collector-emitter saturation VGE = 15 V, IC= 20 A
voltage
VGE = 15V, IC = 20 A,TC= 125 °C
VGE(th)
Gate threshold voltage
VCE = VGE, IC = 250µA
ICES
Collector cut-off current
(VGE = 0)
VCE = 600 V
IGES
Gate-emitter leakage
current (VCE = 0)
VGE = ±20 V
Forward transconductance
VCE = 15 V, IC = 20 A
gfs
Table 5.
Symbol
Cies
Coes
Cres
Qg
Qge
Qgc
4/14
Test conditions
Min.
Typ.
Max. Unit
600
V
2.1
1.8
3.75
VCE = 600 V, TC = 125 °C
2.5
V
V
5.75
V
250
1
µA
mA
± 100
nA
15
S
Dynamic electrical characteristics
Parameter
Input capacitance
Output capacitance
Reverse transfer
capacitance
Total gate charge
Gate-emitter charge
Gate-collector charge
Test conditions
VCE = 25 V, f = 1 MHz,
VGE = 0
VCE = 390 V, IC = 20 A,
VGE = 15 V,
(see Figure 18)
Min.
Typ. Max. Unit
2080
175
52
102
17.5
47
pF
pF
pF
140
nC
nC
nC
STGW30NC60WD
Table 6.
Symbol
td(on)
tr
(di/dt)on
td(on)
tr
(di/dt)on
tr(Voff)
td(off)
tf
tr(Voff)
td(off)
tf
Table 7.
Symbol
Eon(1)
Eoff
Ets
Eon(1)
Eoff
Ets
Electrical characteristics
Switching on/off (inductive load)
Parameter
Test conditions
Turn-on delay time
Current rise time
Turn-on current slope
VCC = 390 V, IC = 20 A
Turn-on delay time
Current rise time
Turn-on current slope
VCC = 390 V, IC = 20 A
Off voltage rise time
Turn-off delay time
Current fall time
VCC = 390 V, IC = 20 A,
Off voltage rise time
Turn-off delay time
Current fall time
Min.
RG = 10 Ω, VGE = 15 V,
(see Figure 17)
RG = 10 Ω, VGE = 15 V,
TC = 125 °C (see Figure 17)
RGE = 10 Ω, VGE = 15 V
(see Figure 17)
VCC = 390 V, IC = 20 A,
RGE = 10 Ω, VGE =15 V,
TC = 125 °C
(see Figure 17)
Typ.
Max.
Unit
29.5
12
1640
ns
ns
A/µs
29
13.5
1600
ns
ns
A/µs
19.5
118
27
ns
ns
ns
46
151
38
ns
ns
ns
Switching energy (inductive load)
Parameter
Test conditions
Turn-on switching losses
Turn-off switching losses
Total switching losses
VCC = 390 V, IC = 20 A
Turn-on switching losses
Turn-off switching losses
Total switching losses
VCC = 390 V, IC = 20 A
RG = 10 Ω, VGE = 15 V,
(see Figure 19)
RG = 10 Ω, VGE = 15 V,
TC = 125°C (see Figure 19)
Min.
Typ.
Max.
Unit
305
181
486
µJ
µJ
µJ
455
355
810
µJ
µJ
µJ
1. Eon is the tun-on losses when a typical diode is used in the test circuit in Figure 19. If the IGBT is offered
in a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs & Diode are at the
same temperature (25°C and 125°C). Eon include diode recovery energy.
5/14
Electrical characteristics
Table 8.
Symbol
Collector-emitter diode
Parameter
VF
Forward on-voltage
trr
Reverse recovery time
Reverse recovery charge
Reverse recovery current
Qrr
Irrm
trr
Qrr
Irrm
6/14
STGW30NC60WD
Reverse recovery time
Reverse recovery charge
Reverse recovery current
Test conditions
IF = 20 A
IF = 20 A, TC = 125 °C
IF = 20 A,VR = 50 V,
di/dt = 100 A/µs
(see Figure 20)
IF = 20 A,VR = 50 V,
TC =125 °C, di/dt = 100
A/µs
(see Figure 20)
Min.
Typ.
Max.
Unit
2.6
1.6
V
V
40
50
2.5
ns
nC
A
80
180
4.5
ns
nC
A
STGW30NC60WD
Electrical characteristics
2.1
Electrical characteristics (curves)
Figure 2.
Output characteristics
Figure 3.
Transfer characteristics
Figure 4.
Transconductance
Figure 5.
Collector-emitter on voltage vs
temperature
HV28940
VCE(V)
VGE=15V
3.2
3
40A
30A
2.8
20A
2.6
2.4
2.2
2
1.8
IC=10A
1.6
1.4
-75
Figure 6.
Gate charge vs gate-source voltage Figure 7.
-50
-25
0
25
50
75
100 125 150 TJ(°C)
Capacitance variations
7/14
Electrical characteristics
Figure 8.
Normalized gate threshold voltage
vs temperature
STGW30NC60WD
Figure 9.
Collector-emitter on voltage vs
collector current
HV28950
VCE(sat)
(V)
3.2
TJ=-50°C
3
TJ=25°C
2.8
2.6
2.4
2.2
TJ=150°C
2
1.8
1.6
1.4
1.2
1
0.8
0
Figure 10. Normalized breakdown voltage vs
temperature
5 10 15 20 25 30 35 40 45 50 55 60 IC(A)
Figure 11. Switching losses vs temperature
Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector
current
8/14
STGW30NC60WD
Electrical characteristics
Figure 14. Thermal impedance
Figure 15. Turn-off SOA
Figure 16. Emitter-collector diode
characteristics
IFM(A)
120
110
Tj=125˚C
(Maximum values)
100
90
80
Tj=125˚C
(Typical values)
70
60
Tj=25˚C
(Maximum values)
50
40
30
20
10
VFM(V)
0
0
1
2
3
4
5
6
9/14
Test circuit
3
STGW30NC60WD
Test circuit
Figure 17. Test circuit for inductive load
switching
Figure 18. Gate charge test circuit
AM01504v1
Figure 19. Switching waveform
AM01505v1
Figure 20. Diode recovery time waveform
VG
IF
trr
90%
VCE
Qrr
di/dt
90%
10%
ta
tb
10%
Tr(Voff)
t
Tcross
90%
IRRM
IRRM
IC
10%
Td(off)
Td(on)
Tr(Ion)
Ton
Tf
Toff
VF
di/dt
AM01506v1
10/14
AM01507v1
STGW30NC60WD
4
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK®
packages. These packages have a Lead-free second level interconnect. The category of
second level interconnect is marked on the package and on the inner box label, in
compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an ST trademark.
ECOPACK specifications are available at: www.st.com
11/14
Package mechanical data
STGW30NC60WD
TO-247 Mechanical data
mm.
Dim.
A
Min.
4.85
A1
2.20
2.60
b
1.0
1.40
b1
2.0
2.40
b2
3.0
3.40
Max.
5.15
c
0.40
0.80
D
19.85
20.15
E
15.45
15.75
e
5.45
L
14.20
14.80
L1
3.70
4.30
L2
18.50
øP
3.55
øR
4.50
S
12/14
Typ
3.65
5.50
5.50
STGW30NC60WD
5
Revision history
Revision history
Table 9.
Document revision history
Date
Revision
Changes
21-Nov-2005
1
Initial release.
29-Nov-2005
2
Modified Figure 5 and Figure 6
06-Mar-2006
3
New template
12-Jul-2007
4
Corrected Figure 11, Figure 12, Figure 13
11-Nov-2008
5
Figure 16 has been updated.
13/14
STGW30NC60WD
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
14/14