STM3210C-EVAL

STM3210C-EVAL STM3210C-EVAL evaluation board Data brief Features ■ Three 5 V power supply options: – power jack – USB connector – daughterboard ■ Boot from user Flash, system memory or SRAM ■ I2S audio DAC, stereo audio jack ■ 2 GByte microSD Card™ or bigger ■ Both A and B type smartcard support ■ I2C compatible serial interface 64 Kbit EEPROM, MEMS and I/O expander ■ RS-232 channel ■ IrDA transceiver ■ USB OTG full speed, USB microAB connection ■ IEEE-802.3-2002 compliant ethernet connector ■ Two channels of CAN 2.0A/B compliant connection ■ Inductor motor control connector ■ JTAG and trace debug support ■ 3.2” 240x320 TFT color LCD with touch screen ■ Joystick with 4-direction control and selector ■ Reset, wakeup, tamper and user buttons ■ 4 color LEDs ■ RTC with backup battery ■ MCU consumption measurement circuit ■ Extension connector for daughterboard or wrapping board Table 1. STM3210C-EVAL The STM3210C-EVAL evaluation board is a complete development platform for STMicroelectronic's ARM Cortex-M3 core-based STM32F107VCT microcontroller. The range of hardware features on the board help you to evaluate all peripherals (USB-OTG FS, ethernet, motor control, CAN, microSD CardTM, smartcard, USART, audio DAC, MEMS, EEPROM and more) and develop your own applications. Extension headers make it easy to connect a daughterboard or wrapping board for your specific application. Device summary Order code August 2010 Description Reference STM32F107VCT evaluation board Doc ID 17799 Rev 1 For further information contact your local STMicroelectronics sales office. 1/3 www.st.com 3 STM3210C-EVAL STM3210C-EVAL hardware block diagram Figure 1 is a block diagram of the STM3210C-EVAL hardware. Figure 1. Hardware block diagram I2S2 3.3V regulator MCU consumption measurement Audio DAC I2C1 MEMS LEDs,Key EEPROM GPIO Joystick Extension connector for GPIOs I/O expander Touchscreen TFT LCD USB microAB connector OTG MicroSD Card SPI3 MC control connector MC USB power switch STM32F107VCT JTAG MII/RMII 2 BNC connector Integrated RJ45 connector CAN1 CAN transceiver CAN DB9 connector CAN2 CAN transceiver CAN DB9 connector RS-232 transceiver USART 2 DB9 connector Debug Trace PHY ADC USART2 IrDA transceiver Potentiometer Battery voltage measurement USART3 Smartcard interface Smartcard connector Demonstration software Demonstration software is preloaded in the board’s Flash memory for easy demonstration of the device peripherals in stand-alone mode. For more information and to download the latest version, refer to www.st.com. Revision history Table 2. 2/3 Document revision history Date Revision 06-Aug-2010 1 Changes Initial release. Doc ID 17799 Rev 1 STM3210C-EVAL Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 17799 Rev 1 3/3