STM690A_10

STM690A, STM692A, STM703 STM704, STM802, STM805, STM817/8/9 5 V supervisor with battery switchover Features ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ 5 V operating voltage NVRAM supervisor for external LPSRAM Chip-enable gating (STM818 only) for external LPSRAM (7 ns max prop delay) RST and RST outputs 200 ms (typ) trec Watchdog timer - 1.6 sec (typ) Automatic battery switchover Low battery supply current - 0.4 µA (typ) Power-fail comparator (PFI/PFO) Low supply current - 40 µA (typ) Guaranteed RST (RST) assertion down to VCC = 1.0 V Operating temperature: –40 °C to +85 °C (industrial grade) RoHS compliance – Lead-free components are compliant with the RoHS directive Device summary Watchdog Active-low Activehigh RST input RST(1) ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Manual reset input(1) Battery Power-fail switchcomparator over ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Chipenable gating Battery freshness seal TSSOP8 3 x 3 (DS)(1) SO8 (M) 8 1 1. Contact local ST sales office for availability. Table 1. Part number STM690A STM692A STM703 STM704 STM802L/M STM805L STM817L/M STM818L/M STM819L/M 1. All RST and RST outputs are push-pull. August 2010 Doc ID 10522 Rev 10 1/43 www.st.com 1 Contents STM690A/692A/703/704/802/805/817/818/819 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1 Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.1.1 1.1.2 1.1.3 1.1.4 1.1.5 1.1.6 1.1.7 1.1.8 1.1.9 1.1.10 MR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 WDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 RST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 RST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 VOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 VBAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 E .......................................................9 ECON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PFI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 Reset output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Push-button reset input (STM703/704/819) . . . . . . . . . . . . . . . . . . . . . . . 13 Watchdog input (NOT available on STM703/704/819) . . . . . . . . . . . . . . . 13 Backup battery switchover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Chip-enable gating (STM818 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Chip-enable input (STM818 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Chip-enable output (STM818 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Power-fail input/output (NOT available on STM818) . . . . . . . . . . . . . . . . 16 Applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Using a SuperCap™ as a backup power source . . . . . . . . . . . . . . . . . . . 17 Negative-going VCC transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Battery freshness seal (STM817/818/819) . . . . . . . . . . . . . . . . . . . . . . . . 19 3 4 5 Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 2/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Contents 6 7 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Doc ID 10522 Rev 10 3/43 List of tables STM690A/692A/703/704/802/805/817/818/819 List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 I/O status in battery backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 DC and AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SO8 - 8-lead plastic small outline, 150 mils body width, package mechanical data . . . . . . 38 TSSOP8 - 8-lead, thin shrink small outline, 3 x 3 mm body size, mechanical data . . . . . . 39 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Marking description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Figure 40. Figure 41. Figure 42. Figure 43. Figure 44. Logic diagram (STM690A/692/802/805/817) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Logic diagram (STM703/704/819) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Logic diagram (STM818) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 STM690A/692A/802/805/817 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 STM703/704/819 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 STM818 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Block diagram (STM690A/692A/802/805/817) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Block diagram (STM703/704/819) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Block diagram (STM818) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Chip-enable gating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Chip-enable waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Power-fail comparator waveform (STM817/818/819) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Power-fail comparator waveform (STM690A/692A/703/704/802/805) . . . . . . . . . . . . . . . . 17 Using a SuperCap™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Freshness seal enable waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 VCC to VOUT on-resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 VBAT to VOUT on-resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Supply current vs. temperature (no load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Battery current vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 VPFI threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Reset comparator propagation delay vs. temperature (other than STM817/818/819) . . . . 22 Reset comparator propagation delay vs. temperature (VBAT = 3.0 V; STM817/818/819) . 23 Power-up tREC vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Normalized reset threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Watchdog time-out period vs. temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 E to ECON on-resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 PFI to PFO propagation delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Output voltage vs. load current (VCC = 5 V; VBAT = 2.8 V; TA = 25 °C) . . . . . . . . . . . . . . . 26 Output voltage vs. load current (VCC = 0 V; VBAT = 2.8 V; TA = 25 °C) . . . . . . . . . . . . . . . 26 RST output voltage vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 RST output voltage vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 RST response time (assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 RST response time (assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Power-fail comparator response time (assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Power-fail comparator response time (de-assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Maximum transient duration vs. reset threshold overdrive . . . . . . . . . . . . . . . . . . . . . . . . . 30 E to ECON propagation delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 E to ECON propagation delay test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 AC testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 MR timing waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Watchdog timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SO8 - 8-lead plastic small outline, 150 mils body width, package mechanical drawing . . . 38 TSSOP8 - 8-lead, thin shrink small outline, 3 x 3 mm body size, outline . . . . . . . . . . . . . . 39 Doc ID 10522 Rev 10 5/43 Description STM690A/692A/703/704/802/805/817/818/819 1 Description The STM690A/692A/703/704/802/805/817/818/819 supervisors are self-contained devices which provide microprocessor supervisory functions with the ability to non-volatize and write-protect external LPSRAM. A precision voltage reference and comparator monitors the VCC input for an out-of-tolerance condition. When an invalid VCC condition occurs, the reset output (RST) is forced low (or high in the case of RST). These devices also offer a watchdog timer (except for STM703/704/819) as well as a power-fail comparator (except for STM818) to provide the system with an early warning of impending power failure. These devices are available in a standard 8-pin SOIC package or a space-saving 8-pin TSSOP package. Figure 1. Logic diagram (STM690A/692/802/805/817) VCC VBAT VOUT WDI PFI STM690A/ 692A/802/ 805/817 RST(RST)(1) PFO VSS AI07894 1. For STM805, reset output is active-high. Figure 2. Logic diagram (STM703/704/819) VCC VBAT VOUT MR PFI STM703/ 704/819 RST PFO VSS AI07895 6/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 3. Logic diagram (STM818) VCC VBAT Description VOUT WDI STM818 E ECON RST VSS AI07896 Table 2. Signal names MR WDI RST RST E(1) Push-button reset input Watchdog input Active-low reset output Active-high reset outpu Chip-enable input Conditioned chip-enable output Supply voltage output Supply voltage Backup supply voltage Power-fail input Power-fail output Ground ECON (1) VOUT VCC VBAT PFI PFO VSS 1. STM818 Figure 4. STM690A/692A/802/805/817 connections SO8/TSSOP8 VOUT VCC VSS PFI 1 2 3 4 8 7 6 5 VBAT RST(RST)(1) WDI PFO AI07889 1. For STM805, reset output is active-high. Doc ID 10522 Rev 10 7/43 Description Figure 5. STM703/704/819 connections STM690A/692A/703/704/802/805/817/818/819 SO8/TSSOP8 VOUT VCC VSS PFI 1 2 3 4 8 7 6 5 VBAT RST MR PFO AI07890 Figure 6. STM818 connections SO8/TSSOP8 VOUT VCC VSS E 1 2 3 4 8 7 6 5 VBAT RST WDI ECON AI07892 1.1 1.1.1 Pin descriptions MR A logic low on MR asserts the reset output. Reset remains asserted as long as MR is low and for trec after MR returns high. This active-low input has an internal pull-up. It can be driven from a TTL or CMOS logic line, or shorted to ground with a switch. Leave open if unused. 1.1.2 WDI If WDI remains high or low for 1.6 sec, the internal watchdog timer runs out and reset is triggered. The internal watchdog timer clears while reset is asserted or when WDI sees a rising or falling edge. The watchdog function can be disabled by allowing the WDI pin to float. 1.1.3 RST Pulses low for trec when triggered, and stays low whenever VCC is below the reset threshold or when MR is a logic low. It remains low for trec after either VCC rises above the reset threshold, the watchdog triggers a reset, or MR goes from low to high. 1.1.4 RST Pulses high for trec when triggered, and stays high whenever VCC is above the reset threshold or when MR is a logic high. It remains high for trec after either VCC falls below the reset threshold, the watchdog triggers a reset, or MR goes from high to low. 8/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Description 1.1.5 VOUT When VCC is above the switchover voltage (VSO), VOUT is connected to VCC through a Pchannel MOSFET switch. When VCC falls below VSO, VBAT connects to VOUT. 1.1.6 VBAT When VCC falls below VSO, VOUT switches from VCC to VBAT. When VCC rises above VSO + hysteresis, VOUT reconnects to VCC. VBAT may exceed VCC. Connect to VCC if no battery is used. 1.1.7 E The input to the chip-enable gating circuit. Connect to ground if unused. 1.1.8 ECON ECON goes low only when E is low and reset is not asserted. If ECON is low when reset is asserted, ECON will remain low for 15 µs or until E goes high, whichever occurs first. In the disabled mode, ECON is pulled up to VOUT. 1.1.9 PFI When PFI is less than VPFI or when VCC falls below 2.4 V (or VSO), PFO goes low; otherwise, PFO remains high. Connect to ground if unused. 1.1.10 PFO When PFI is less than VPFI, or VCC falls below 2.4 V (or VSO), PFO goes low; otherwise, PFO remains high. Leave open if unused. Output type is push-pull. Doc ID 10522 Rev 10 9/43 Description STM690A/692A/703/704/802/805/817/818/819 Table 3. Pin description Pin STM690A STM703 STM704 STM819 6 7 1 2 8 4 5 3 6 7 1 2 8 4 5 3 MR WDI RST RST VOUT VCC VBAT E ECON PFI PFO VSS Push-button reset input Watchdog input Active-low reset output Active-high reset output Supply output for external LPSRAM Supply voltage Backup battery input Chip-enable input Conditioned chip-enable output Power-fail input Power-fail output (push-pull) Ground STM805 STM818 STM692A STM802 STM817 Name Function 6 7 1 2 8 4 5 3 6 7 1 2 8 4 5 3 Figure 7. Block diagram (STM690A/692A/802/805/817) VCC VBAT VOUT VSO COMPARE VRST COMPARE WDI WATCHDOG TIMER trec Generator RST(RST) (1) PFI VPFI COMPARE PFO AI07897 1. For STM805, reset output is active-high. 10/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 8. Block diagram (STM703/704/819) Description VCC VBAT VOUT VSO COMPARE VRST COMPARE MR trec Generator RST PFI VPFI COMPARE PFO AI07898 Figure 9. VCC Block diagram (STM818) VOUT VBAT VSO COMPARE VRST COMPARE WDI WATCHDOG TIMER trec Generator RST ECON OUTPUT CONTROL E ECON AI07899a Doc ID 10522 Rev 10 11/43 Description Figure 10. Hardware hookup STM690A/692A/703/704/802/805/817/818/819 Regulator Unregulated Voltage VIN VCC VCC VOUT VCC VCC STM690A/692A/ 703/704/802/805/ 817/818/819 LPSRAM E E 0.1 F WDI(1) From Microprocessor E(2) R1 PFI(3) R2 Push-Button MR(4) VBAT RST (5) 0.1 F ECON(2) PFO(3) To Microprocessor NMI To Microprocessor Reset AI07893 1. For STM690A/692A/802/805/817/818. 2. For STM818 only. 3. Not available on STM818. 4. For STM703/704/819. 5. Active high on STM805. 12/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Operation 2 2.1 Operation Reset output The STM690A/692A/703/704/802/805/817/818/819 Supervisor asserts a reset signal to the MCU whenever VCC goes below the reset threshold (VRST), a watchdog time-out occurs, or when the Push-button Reset Input (MR) is taken low. RST is guaranteed to be a logic low (logic high for STM805) for 0V < VCC < VRST if VBAT is greater than 1 V. Without a backup battery, RST is guaranteed valid down to VCC =1 V. During power-up, once VCC exceeds the reset threshold an internal timer keeps RST low for the reset time-out period, trec. After this interval RST returns high. If VCC drops below the reset threshold, RST goes low. Each time RST is asserted, it stays low for at least the reset time-out period (trec). Any time VCC goes below the reset threshold the internal timer clears. The reset timer starts when VCC returns above the reset threshold. 2.2 Push-button reset input (STM703/704/819) A logic low on MR asserts reset. Reset remains asserted while MR is low, and for trec (see Figure 41) after it returns high. The MR input has an internal 40 kΩ pull-up resistor, allowing it to be left open if not used. This input can be driven with TTL/CMOS-logic levels or with open-drain/collector outputs. Connect a normally open momentary switch from MR to GND to create a manual reset function; external debounce circuitry is not required. If MR is driven from long cables or the device is used in a noisy environment, connect a 0.1 µF capacitor from MR to GND to provide additional noise immunity. MR may float, or be tied to VCC when not used. 2.3 Watchdog input (NOT available on STM703/704/819) The watchdog timer can be used to detect an out-of-control MCU. If the MCU does not toggle the Watchdog Input (WDI) within tWD(1.6 sec typ), the reset is asserted. The internal watchdog timer is cleared by either: 1. 2. a reset pulse, or by toggling WDI (high-to-low or low-to-high), which can detect pulses as short as 50ns. If WDI is tied high or low, a reset pulse is triggered every 1.8 sec (tWD + trec). The timer remains cleared and does not count for as long as reset is asserted. As soon as reset is released, the timer starts counting (see Figure 42). Note: 1 The watchdog function may be disabled by floating WDI or tri-stating the driver connected to WDI. When tri-stated or disconnected, the maximum allowable leakage current is 10 µA and the maximum allowable load capacitance is 200 pF. Input pulses less than 20 ns will be ignored. 2 Doc ID 10522 Rev 10 13/43 Operation STM690A/692A/703/704/802/805/817/818/819 2.4 Backup battery switchover In the event of a power failure, it may be necessary to preserve the contents of external SRAM through VOUT. With a backup battery installed with voltage VBAT, the devices automatically switch the SRAM to the backup supply when VCC falls. Note: When the battery is first connected without VCC power applied, the device does not immediately provide backup battery voltage on VOUT. Only after VCC exceeds VRST will the switchover operate as described below. This mode allows a battery to be attached during manufacturing but not used until after the system has been activated for the first time. As a result, no battery power is consumed by the device during storage and shipment. For the STM81x devices, the battery freshness seal can be initiated again by following the procedure outlined in Section 2.12. If the backup battery is not used, connect both VBAT and VOUT to VCC . Whenever VCC falls below the switchover voltage, VSO, VOUT is connected to VBAT through a 100 Ω switch. VSO is the lesser of VBAT and VRST. Choosing the lesser allows the device to be powered by VCC for as long as possible before switching over thereby maximizing the battery life. Assuming VBAT > 2.0 V, switchover at VSO ensures that battery backup mode is entered before VOUT gets too close to the 2.0 V minimum required to reliably retain data in most external SRAMs. When VCC recovers, hysteresis is used to avoid oscillation around the VSO point. VOUT is connected to VCC through a 3 Ω PMOS power switch. Note: The backup battery may be removed while VCC is valid, assuming VBAT is adequately decoupled (0.1 µF typ), without danger of triggering a reset. Table 4. I/O status in battery backup VOUT VCC PFI PFO E ECON WDI MR RST RST VBAT Connected to VBAT through internal switch Disconnected from VOUT Disabled Logic low High impedance Logic high Watchdog timer is disabled Disabled Logic low Logic high Connected to VOUT 14/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Operation 2.5 Chip-enable gating (STM818 only) Internal gating of the chip-enable (E) signal prevents erroneous data from corrupting the external CMOS RAM in the event of an undervoltage condition. The STM818 uses a series transmission gate from E to ECON (see Figure 11). During normal operation (reset not asserted), the E transmission gate is enabled and passes all E transitions. When reset is asserted, this path becomes disabled, preventing erroneous data from corrupting the CMOS RAM. The short propagation delay from E to ECON enables the STM818 to be used with most µPs. If E is low when reset asserts, ECON remains low for typically 15 µs (or until E goes high) to permit the current WRITE cycle to complete. Connect E to VSS if unused. 2.6 Chip-enable input (STM818 only) The chip-enable transmission gate is disabled and E is high impedance (disabled mode) while reset is asserted. During a power-down sequence when VCC passes the reset threshold, the chip-enable transmission gate disables and E immediately becomes high impedance if the voltage at E is high. If E is low when reset asserts, the chip-enable transmission gate will disable 15 µs after reset asserts (see Figure 12). This permits the current WRITE cycle to complete during power-down. Any time a reset is generated, the chip-enable transmission gate remains disabled and E remains high impedance (regardless of E activity) for the reset time-out period. When the chip-enable transmission gate is enabled, the impedance of E appears as a 40 Ω resistor in series with the load at ECON. The propagation delay through the chip-enable transmission gate depends on VCC, the source impedance of the drive connected to E, and the loading on ECON. The chip-enable propagation delay is production tested from the 50% point on E to the 50% point on ECON using a 50 Ω driver and a 50 pF load capacitance (see Figure 39). For minimum propagation delay, minimize the capacitive load at ECON and use a low-output impedance driver. 2.7 Chip-enable output (STM818 only) When the chip-enable transmission gate is enabled, the impedance of ECON is equivalent to a 40 Ω resistor in series with the source driving E. In the disabled mode, the transmission gate is off and an active pull-up connects ECON to VOUT (see Figure 11). This pull-up turns off when the transmission gate is enabled. Figure 11. Chip-enable gating VCC VRST COMPARE trec Generator RST VOUT ECON OUTPUT CONTROL E ECON AI08802 Doc ID 10522 Rev 10 15/43 Operation Figure 12. Chip-enable waveform VCC VRST VBAT STM690A/692A/703/704/802/805/817/818/819 ECON RST trec 15µs trec E XX XX AI08803b 2.8 Power-fail input/output (NOT available on STM818) The Power-fail Input (PFI) is compared to an internal reference voltage (independent from the VRST comparator). If PFI is less than the power-fail threshold (VPFI), the Power-Fail Output (PFO) will go low. This function is intended for use as an undervoltage detector to signal a failing power supply. Typically PFI is connected through an external voltage divider (see Figure 12) to either the unregulated DC input (if it is available) or the regulated output of the VCC regulator. The voltage divider can be set up such that the voltage at PFI falls below VPFI several milliseconds before the regulated VCC input to the STM690A/692A/703/704/802/805/817/818/819 Supervisor or before the microprocessor drops below the minimum operating voltage. This provides several milliseconds of advanced warning that power is about to fail. During battery backup, the power-fail comparator turns off and PFO goes (or remains) low (see Figure 13 below and Figure 14). This occurs after VCC drops below 2.4 V (or VSO). When power returns, PFO is forced high (STM817/819 only), irrespective of VPFI for the WRITE protect time (trec). At the end of this time, the power-fail comparator is enabled and PFO follows PFI. If the comparator is unused, PFI should be connected to VSS and PFO left unconnected. PFO may be connected to MR on the STM703/704/818 so that a low voltage on PFI will generate a reset output. 2.9 Applications information These supervisor circuits are not short-circuit protected. Shorting VOUT to ground excluding power-up transients such as charging a decoupling capacitor - destroys the device. Decouple both VCC and VBAT pins to ground by placing 0.1 µF capacitors as close to the device as possible. 16/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 13. Power-fail comparator waveform (STM817/818/819) VCC VRST Operation VSO (or 2.4V) trec PFO (STM817/819) PFO follows PFI PFO follows PFI RST to ECON Delay (STM818) RST ECON (STM818) AI08804a Figure 14. Power-fail comparator waveform (STM690A/692A/703/704/802/805) VCC VRST 2.4V (or VSO) trec PFO PFO follows PFI PFO follows PFI RST AI08832a 2.10 Using a SuperCap™ as a backup power source SuperCaps™ are capacitors with extremely high capacitance values (e.g., 0.47 F) for their size. Figure 15 shows how to use a SuperCap as a backup power source. The SuperCap may be connected through a diode to the 5 V supply. Since VBAT can exceed VCC while VCC is above the reset threshold, there are no special precautions for using these supervisors with a SuperCap. Doc ID 10522 Rev 10 17/43 Operation STM690A/692A/703/704/802/805/817/818/819 2.11 Negative-going VCC transients The STM690A/692A/703/704/802/805/817/818/819 Supervisors are relatively immune to negative-going VCC transients (glitches). Figure 37 shows typical transient duration versus reset comparator overdrive (for which the STM690A/692A/703/704/802/805/817/818/819 will NOT generate a reset pulse). The graph was generated using a negative pulse applied to VCC, starting at VRST + 0.3 V and ending below the reset threshold by the magnitude indicated (comparator overdrive). The graph indicates the maximum pulse width a negative VCC transient can have without causing a reset pulse. As the magnitude of the transient increases (further below the threshold), the maximum allowable pulse width decreases. Any combination of duration and overdrive which lies under the curve will NOT generate a reset signal. Typically, a VCC transient that goes 100 mV below the reset threshold and lasts 40 µs or less will not cause a reset pulse. A 0.1 µF bypass capacitor mounted as close as possible to the VCC pin provides additional transient immunity. 18/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Operation 2.12 Battery freshness seal (STM817/818/819) The battery freshness seal disconnects the backup battery from internal circuitry and VOUT until it is needed. This allows an OEM to ensure that the backup battery connected to VBAT will be fresh when the final product is put to use. To enable the freshness seal: 1. 2. 3. 4. Connect a battery to VBAT Ground PFO Bring VCC above the reset threshold and hold it there until reset is deasserted following the reset timeout period and Bring VCC down again (Figure 16) Use the same procedure for the STM818, but ground ECON instead of PFO. Once the battery freshness seal is enabled (disconnecting the backup battery from internal circuitry and anything connected to VOUT), it remains enabled until VCC is brought above VRST. Figure 15. Using a SuperCap™ 5V VCC VOUT To external SRAM STMXXX VBAT GND RST To µP AI08805 Figure 16. Freshness seal enable waveform VRST VCC trec RST ECON out state latched at 1/2 trec, Freshness Seal enabled PFO out state latched at 1/2 trec, Freshness Seal Enabled ECON (Externally held at 0V) (STM818) (Externally held at 0V) PFO (STM817/819) AI08806 Doc ID 10522 Rev 10 19/43 Typical operating characteristics STM690A/692A/703/704/802/805/817/818/819 3 Note: Typical operating characteristics Typical values are at TA = 25 °C. Figure 17. VCC to VOUT on-resistance vs. temperature 5.0 ) 4.0 VCC = 3.0V VCC = 4.5V VCC = 5.5V VCC to V OUT on-resistance ( 3.0 2.0 1.0 0.0 –40 –20 0 20 40 60 80 100 120 AI10498 Temperature (° C) Figure 18. VBAT to VOUT on-resistance vs. temperature 160 ) VBAT to VOUT on-resistance ( 140 120 100 80 60 40 20 0 –40 –20 0 20 40 60 80 100 120 AI09140b VBAT = 2.0V VBAT = 3.0V VBAT = 3.3V VBAT = 3.6V Temperature (° C) 20/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 19. Supply current vs. temperature (no load) 30 Typical operating characteristics 25 Supply Current (µA) 20 15 VCC = 2.7V VCC = 3.0V VCC = 3.6V VCC = 4.5V VCC = 5.5V 10 5 0 –40 –20 0 20 40 60 80 100 120 AI09141b Temperature (° C) Figure 20. Battery current vs. temperature 1000 Battery Supply Current (nA) 100 VBAT = 2.0V VBAT = 3.0V VBAT = 3.6V 10 1 0.1 –40 –20 0 20 40 60 80 100 120 AI10499 Temperature (° C) Doc ID 10522 Rev 10 21/43 Typical operating characteristics Figure 21. VPFI threshold vs. temperature 1.270 1.265 1.260 VCC = 3.0V VCC = 4.5V VCC = 4.75V VCC = 5.5V STM690A/692A/703/704/802/805/817/818/819 VPFI Threshold (V) 1.255 1.250 1.245 1.240 1.235 1.230 1.225 –40 –20 0 20 40 60 80 100 120 AI09142c Temperature (° C) Figure 22. Reset comparator propagation delay vs. temperature (other than STM817/818/819) 30 28 26 Propagation Delay (µs) 24 22 20 18 16 14 12 10 –40 –20 0 20 40 60 80 100 120 AI09143b Temperature (° C) 22/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Typical operating characteristics Figure 23. Reset comparator propagation delay vs. temperature (VBAT = 3.0 V; STM817/818/819) 350 1v/ms 300 10V/ms Propagation Delay (µs) 250 200 150 100 50 0 –40 –20 0 20 40 60 80 100 120 AI11100 Temperature (° C) Figure 24. Power-up tREC vs. temperature 240 235 230 trec (ms) VCC = 3.0V 225 VCC = 4.5V VCC = 5.5V 220 215 210 –40 –20 0 20 40 60 80 100 120 AI09144b Temperature (° C) Doc ID 10522 Rev 10 23/43 Typical operating characteristics STM690A/692A/703/704/802/805/817/818/819 Figure 25. Normalized reset threshold vs. temperature 1.004 Normalized Reset Threshold 1.002 1.000 0.998 0.996 –40 –20 0 20 40 60 80 100 120 AI09145b Temperature (° C) Figure 26. Watchdog time-out period vs. temperature 1.90 Watchdog Time-out Period (sec) 1.85 1.80 1.75 VCC = 3.0V VCC = 4.5V VCC = 5.5V 1.70 1.65 1.60 –40 –20 0 20 40 60 80 100 120 AI09146b Temperature (° C) 24/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 27. E to ECON on-resistance vs. temperature 60 Typical operating characteristics 50 E to ECON On-Resistance ( ) 40 30 20 VCC = 3.0V VCC = 4.5V VCC = 5.5V 10 0 –40 –20 0 20 40 60 80 100 120 AI09147b Temperature (° C) Figure 28. PFI to PFO propagation delay vs. temperature 4.0 PFI to PFO Propagation Delay (µs) VCC = 3.0V VCC = 3.6V 3.0 VCC = 4.5V VCC = 5.5V 2.0 1.0 0.0 –40 –20 0 20 40 60 80 100 120 AI09148b Temperature (° C) Doc ID 10522 Rev 10 25/43 Typical operating characteristics STM690A/692A/703/704/802/805/817/818/819 Figure 29. Output voltage vs. load current (VCC = 5 V; VBAT = 2.8 V; TA = 25 °C) 5.00 4.98 VOUT (V) 4.96 4.94 0 10 20 30 40 50 AI10496 IOUT (mA) Figure 30. Output voltage vs. load current (VCC = 0 V; VBAT = 2.8 V; TA = 25 °C) 2.80 2.78 2.76 VOUT (V) 2.74 2.72 2.70 2.68 2.66 0.0 0.2 0.4 0.6 0.8 1.0 AI10497 IOUT (mA) 26/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 31. RST output voltage vs. supply voltage Typical operating characteristics 5 VRST VCC 4 5 4 VRST (V) 2 2 1 1 0 0 500ms/div AI09149b Figure 32. RST output voltage vs. supply voltage 5 VRST VCC 5 4 4 VRST (V) 2 2 1 1 0 0 500ms/div AI09150b Doc ID 10522 Rev 10 VCC (V) 3 3 VCC (V) 3 3 27/43 Typical operating characteristics Figure 33. RST response time (assertion) STM690A/692A/703/704/802/805/817/818/819 5V VCC 1V/div 4V 5V 4V RST 1V/div 0V 5µs/div AI09151b Figure 34. RST response time (assertion) 5V VCC 4V 1V/div 4V RST 1V/div 0V 5µs/div AI09152b 28/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 35. Power-fail comparator response time (assertion) 5V Typical operating characteristics PFO 1V/div 0V 1.3V PFI 500mV/div 0V 500ns/div AI09153b Figure 36. Power-fail comparator response time (de-assertion) 5V PFO 1V/div 0V 1.3V PFI 500mV/div 0V 500ns/div AI09154b Doc ID 10522 Rev 10 29/43 Typical operating characteristics STM690A/692A/703/704/802/805/817/818/819 Figure 37. Maximum transient duration vs. reset threshold overdrive 6000 5000 Transient Duration (µs) 4000 Reset occurs above the curve. 3000 2000 1000 0 0.001 0.01 0.1 1 10 AI09156b Reset Comparator Overdrive, VRST – VCC (V) Figure 38. E to ECON propagation delay vs. temperature 4.0 E to ECON Propagation Delay (ns) 3.0 2.0 1.0 VCC = 3.0V VCC = 4.5V VCC = 5.5V 0.0 –40 –20 0 20 40 60 80 100 120 AI09157b Temperature (° C) 30/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Maximum ratings 4 Maximum ratings Stressing the device above the rating listed in the absolute maximum ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 5. Symbol TSTG TSLD(1) VIO VCC/VBAT IO PD Absolute maximum ratings Parameter Storage temperature (VCC off) Lead solder temperature for 10 seconds Input or output voltage Supply voltage Output current Power dissipation Value –55 to 150 260 –0.3 to VCC +0.3 –0.3 to 6.0 20 320 Unit °C °C V V mA mW 1. Reflow at peak temperature of 260 °C. The time above 255 °C must not exceed 30 seconds. Doc ID 10522 Rev 10 31/43 DC and AC parameters STM690A/692A/703/704/802/805/817/818/819 5 DC and AC parameters This section summarizes the operating measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristics Tables that follow, are derived from tests performed under the measurement conditions summarized in Table 6: Operating and AC measurement conditions. Designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. Table 6. Operating and AC measurement conditions Parameter VCC/VBAT supply voltage Ambient operating temperature (TA) Input rise and fall times Input pulse voltages Input and output timing ref. voltages STM690A/692A/703/704/802/805/ 817/818/819 1.0 to 5.5 –40 to 85 ≤5 0.2 to 0.8VCC 0.3 to 0.7VCC Unit V °C ns V V Figure 39. E to ECON propagation delay test circuit VCC VCC VBAT 3.6V STMXXX 25 Equivalent Source Impedance E 50 50 Cable 50 GND ECON 50pF CL(1) AI08854 1. CL includes load capacitance and scope probe capacitance. 32/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Figure 40. AC testing input/output waveforms DC and AC parameters 0.8VCC 0.7VCC 0.3VCC AI02568 0.2VCC Figure 41. MR timing waveform MR tMLRL RST (1) tMLMH trec AI07837a 1. RST for STM805. Figure 42. Watchdog timing VCC RST trec tWD WDI AI07891 Doc ID 10522 Rev 10 33/43 DC and AC parameters STM690A/692A/703/704/802/805/817/818/819 Table 7. Sym VCC , VBAT(2) ICC DC and AC characteristics Alternative Description Operating voltage VCC supply current VCC supply current in battery backup mode VBAT supply current in battery backup mode Test condition(1) TA = –40 to +85 °C Excluding IOUT (VCC < 5.5 V) Excluding IOUT (VBAT = 2.3 V, VCC = 2.0 V, MR = VCC) Excluding IOUT (VBAT = 3.6 V) IOUT1 = 5 mA(5) VCC – 0.03 VCC – 0.3 VCC – 0.0015 VBAT – 0.1 Min 1.2(3) 25 25 0.4 VCC – 0.015 VCC – 0.15 VCC – 0.0006 VBAT – 0.034 VBAT – 0.14 3 100 4.5 V < VCC < 5.5 V 0 V < VIN < VCC WDI = VCC , time average WDI = GND, time average 4.5 V < VCC < 5.5 V VRST (max) < VCC < 5.5 V 4.5 V < VCC < 5.5 V VRST (max) < VCC < 5.5 V VCC = VRST (max), ISINK = 3.2 mA VCC = VRST (max), IOUT = 1.6 mA, E = 0 V ISINK = 50 µA, VCC = 1.0 V, VBAT = VCC , TA = 0°C to 85°C ISINK = 100 µA, VCC = 1.2 V, VBAT = VCC –20 2.0 0.7VCC 0.8 0.3VCC 0.3 0.2VCC 0.3 0.3 75 –25 125 2 120 –15 300 +25 160 4 Typ Max 5.5 60 35 1.0 Unit V µA µA µA V V V V V Ω Ω µA nA µA µA V V V V V V V V IBAT(4) VOUT1 VOUT voltage (active) IOUT1 = 75 mA IOUT1 = 250 µA, VCC > 2.5 V(5) VOUT2 VOUT voltage (battery backup) VCC to VOUT on-resistance VBAT to VOUT on-resistance Input leakage current (MR) IOUT2 = 250 µA, VBAT = 2.3 V IOUT2 = 1 mA, VBAT = 2.3 V ILI Input leakage current (PFI) Input leakage current (WDI)(6) VIH VIH VIL VIL Input high voltage (MR) Input high voltage (WDI) Input low voltage (MR) Input low voltage (WDI) Output low voltage (PFO, RST, RST) VOL Output low voltage (ECON) VOL Output low voltage (RST) 34/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Table 7. Sym DC and AC parameters DC and AC characteristics (continued) Alternative Description Output high voltage (RST, RST) Test condition(1) ISOURCE = 1 mA VCC = VRST (max) VCC = VRST (max), IOUT = 1.6 mA, E= VCC ISOURCE = 75 µA, VCC = VRST (max) ISOURCE = 4 µA, VCC = 1.1 V, VBAT = VCC , TA = 0°C to 85°C ISOURCE = 4 µA, VCC = 1.2 V, VBAT = VCC VOH battery backup (RST, RST) ISOURCE = 100 µA, VCC = 0, VBAT = 2.8 V ISOURCE = 75 µA, VCC = 0, VBAT = 2.8 V 0.8VBAT 0.8VBAT Min Typ Max Unit 2.4 0.8VCC 0.8VCC 0.8 0.9 V V V V V V V VOH Output high voltage (ECON) Output high voltage (PFO) VOH Output high voltage VOHB VOH battery backup (ECON) Power-fail comparator (NOT available on STM818) PFI falling (VCC = 5 V) All other versions STM802 tPFD ISC PFI to PFO propagation delay PFO output short to GND current VCC = 5 V, VPFO = 0 V 0.1 1.20 1.225 1.25 1.250 2 0.75 1.30 1.275 V V µs VPFI PFI input threshold 2.0 mA Battery switchover Battery backup switchover voltage(7)(8) (VCC < VBAT & VCC < VRST) Hysteresis Reset thresholds VRST Reset threshold(9) Reset threshold hysteresis VCC to RST delay (from VRST, VCC falling at 10 V/ms) STM817/818/819 STM690A/703, STM8XXL STM692A/704, STM8XXM 4.50 4.25 4.65 4.40 25 4.75 4.50 V V mV Power-down VRST > VBAT VRST < VBAT Power-up VRST > VBAT VRST < VBAT VBAT VRST VBAT VRST 40 V V V V mV VSO 100 µs Doc ID 10522 Rev 10 35/43 DC and AC parameters Table 7. Sym tREC STM690A/692A/703/704/802/805/817/818/819 DC and AC characteristics (continued) Alternative Description RST pulse width Test condition(1) Min 140 Typ 200 Max 280 Unit ms Push-button reset input (STM703/704/819) STM703/704 tMLMH tMR MR pulse width STM819 STM703/704 tMLMR tMRD MR to RST output delay STM819 MR glitch immunity MR pull-up resistor STM819 MR = 0 V, VCC = 5 V 45 120 100 63 85 ns ns kΩ 1 250 µs ns 150 ns Watchdog timer (NOT available on STM703/704/819) tWD Watchdog timeout period WDI pulse width Chip-enable gating (STM818 only) E to ECON resistance E to ECON propagation delay Reset to ECON high delay ECON short circuit current VCC = VRST (max) 4.5 V < VCC < 5.5 V (Power-down) VCC = 5 V, disable mode, E = logic high, ECON = 0 V 0.1 40 2 15 0.75 2.0 150 7 Ω ns µs mA VRST (max) < VCC < 5.5 V VRST (max) < VCC < 5.5 V 1.12 50 1.60 2.24 s ns 1. Valid for ambient operating temperature: TA = –40 to 85 °C; VCC = 4.75 V to 5.5 V for “L” versions; VCC = 4.5 V to 5.5 V for “M” versions; and VBAT = 2.8 V (except where noted). 2. VCC supply current, logic input leakage, watchdog functionality, push-button reset functionality, PFI functionality, state of RST and RST tested at VBAT = 3.6 V, and VCC = 5.5 V. The state of RST or RST and PFO is tested at VCC = VCC (min). Either VCC or VBAT can go to 0 V if the other is greater than 2.0 V. 3. VCC (min) = 1.0 V for TA = 0 °C to +85 °C. 4. Tested at VBAT = 3.6 V, VCC = 3.5 V and 0 V. 5. Guaranteed by design. 6. WDI input is designed to be driven by a three-state output device. To float WDI, the “high impedance mode” of the output device must have a maximum leakage current of 10 µA and a maximum output capacitance of 200 pF. The output device must also be able to source and sink at least 200 µA when active. 7. When VBAT > VCC > VRST, VOUT remains connected to VCC until VCC drops below VRST. 8. When VRST > VCC > VBAT, VOUT remains connected to VCC until VCC drops below the battery voltage (VBAT) – 75 mV. 9. For VCC falling. 36/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Doc ID 10522 Rev 10 37/43 Package mechanical data STM690A/692A/703/704/802/805/817/818/819 Figure 43. SO8 - 8-lead plastic small outline, 150 mils body width, package mechanical drawing A2 B e D A C ddd 8 E 1 H A1 L SO-A Note: Drawing is not to scale. Table 8. SO8 - 8-lead plastic small outline, 150 mils body width, package mechanical data mm Symbol Typ A A1 B C D ddd E e H h L α N 1.27 Min 1.35 0.10 0.33 0.19 4.80 3.80 5.80 0.25 0.40 0° 8 Max 1.75 0.25 0.51 0.25 5.00 0.10 4.00 6.20 0.50 0.90 8° Typ 0.050 Min 0.053 0.004 0.013 0.007 0.189 0.150 0.228 0.010 0.016 0° 8 Max 0.069 0.010 0.020 0.010 0.197 0.004 0.157 0.244 0.020 0.035 8° inches 38/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Package mechanical data Figure 44. TSSOP8 - 8-lead, thin shrink small outline, 3 x 3 mm body size, outline D 8 5 E1 E c 1 4 A1 A CP b e A2 L L1 TSSOP8BM Note: Drawing is not to scale. Table 9. TSSOP8 - 8-lead, thin shrink small outline, 3 x 3 mm body size, mechanical data mm Symbol Typ A A1 A2 b c CP D e E E1 L L1 α N 0.85 3.00 0.65 4.90 3.00 0.55 0.95 Min 0.05 0.75 0.25 0.13 2.90 4.65 2.90 0.40 0° 8 Max 1.10 0.15 0.95 0.40 0.23 0.10 3.10 5.15 3.10 0.70 6° Typ 0.034 0.118 0.026 0.193 0.118 0.022 0.037 Min 0.002 0.030 0.010 0.005 0.114 0.183 0.114 0.016 0° 8 Max 0.043 0.006 0.037 0.016 0.009 0.004 0.122 0.203 0.122 0.030 6° inches Doc ID 10522 Rev 10 39/43 Part numbering STM690A/692A/703/704/802/805/817/818/819 7 Part numbering Table 10. Example: Ordering information scheme STM690A M 6 E Device type STM690A/692A/703/704/802/805/817/818/819 Threshold voltage STM690A, STM703: blank: VRST = 4.50 V to 4.75 V STM692A, STM704: blank: VRST = 4.25 V to 4.50 V STM8xx: L: VRST = 4.50 V to 4.75 V M: VRST = 4.25 V to 4.50 V Package M = SO8 DS(1) = TSSOP8 Temperature range 6: –40 °C to 85 °C Shipping method E = ECOPACK® package, tubes F = ECOPACK® package, tape & reel 1. Contact local ST sales office for availability. For other options or for more information on any aspect of this device, please contact the ST sales office nearest you. 40/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Part numbering Table 11. Marking description Reset threshold 4.65 V 4.40 V 4.65 V 4.40 V 4.65 V 4.40 V 4.65 V 4.65 V TSSOP8 SO8 Package SO8 SO8 SO8 SO8 SO8 SO8 SO8 SO8 Topside marking 690A 692A 703 704 802L 802M 805L 817L Part number STM690A STM692A STM703 STM704 STM802L STM802M STM805L STM817L STM817M 4.40 V TSSOP8 SO8 817M STM818L 4.65 V TSSOP8 SO8 818L STM818M 4.40 V TSSOP8 SO8 818M STM819L 4.65 V TSSOP8 SO8 819L STM819M 4.40 V TSSOP8 819M Doc ID 10522 Rev 10 41/43 Revision history STM690A/692A/703/704/802/805/817/818/819 8 Revision history Table 12. Date Oct-2003 31-Oct-2003 22-Dec-2003 16-Jan-2004 08-Apr-2004 25-May-2004 05-Jul-2004 29-Sep-2004 01-Mar-2005 20-Jan-2006 21-Oct-2008 20-Nov-2009 18-Aug-2010 Document revision history Revision 1 1.1 2 2.1 2.2 3 4 5 6 7 8 9 10 Initial release. Update DC characteristics (Table 7). Reformatted; updated characteristics (cover page, Figure 2, 3, 6, 7, 8, 9, 10, 11, 12, 13, 14, 16, Table 3, 4, 7, 9, 11). Add typical characteristics (Figure 18, 19, 21, 22, 24, 25, 26, 27, 28, 31, 32, 33, 34, 35, 36, 37, 38). Update characteristics (Figure 12, 22, 28, 32, 33, 34, 37; Table 1, 7). Remove references to “open drain” (cover page, 4, 7; Table 2); update characteristics (Table 3, 7). Update package availability, pin description; promote document (cover page, Figure 13, 14; Table 3, 7, 10). Clarify root part numbers, pin descriptions (Figure 10, 12, 39; Table 7, 10). Update characteristics (Figure 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38) Correct marking, update lead-free text (Table 10, 11) Reformatted, minor text changes; updated Table 3, 4, 7, 10, Figure 9, 10, 11, 12, 16, 39, Section 6: Package mechanical data. Updated text in Section 6, Table 5. Updated Section 2.4: Backup battery switchover. Changes 42/43 Doc ID 10522 Rev 10 STM690A/692A/703/704/802/805/817/818/819 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 10522 Rev 10 43/43