STM805TDS6E

STM690, STM704, STM795 STM802, STM804, STM805, STM806 3 V supervisor with battery switchover Features ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ RST or RST outputs NVRAM supervisor for external LPSRAM Chip enable gating (STM795 only) for external LPSRAM (7 ns max prop delay) Manual (push-button) reset input 200 ms (typ) trec Watchdog timer - 1.6 s (typ) Automatic battery switchover Low battery supply current - 0.4 µA (typ) Power-fail comparator (PFI/PFO) Low supply current - 40 µA (typ) Guaranteed RST (RST) assertion down to VCC = 1.0 V Operating temperature: –40 °C to 85 °C (industrial grade) RoHS compliance – Lead-free components are compliant with the RoHS directive Device summary Watchdog Input Active- low Active- high RST(1) RST(1) ✓ ✓ ✓ ✓ ✓ ✓ ✓ (2) 8 1 SO8 (M) TSSOP8 3x3 (DS)(1) 1. Contact local ST sales office for availability. Table 1. Manual reset input Battery Power-fail switchover comparator ✓ ✓ ✓ Chip enable gating STM690T/S/R STM704T/S/R STM795T/S/R STM802T/S/R STM804T/S/R STM805T/S/R STM806T/S/R ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓(2) ✓(2) ✓ ✓ ✓ ✓ 1. All RST outputs push-pull (unless otherwise noted). 2. Open drain output. August 2010 Doc ID 10519 Rev 9 1/42 www.st.com 1 Contents STM690, STM704, STM795, STM802, STM804, STM805, STM806 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1 Pin descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.1.1 1.1.2 1.1.3 1.1.4 1.1.5 1.1.6 1.1.7 1.1.8 1.1.9 1.1.10 1.1.11 MR (manual reset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 WDI (watchdog input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 RST (active-low reset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 RST (active-high reset - open drain) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PFI (power-fail input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PFO (power-fail output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 VOUT (supply output voltage) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Vccsw (VCC switch output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 E (chip enable input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 ECON (conditional chip enable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 VBAT (backup battery input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 Reset output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Push-button reset input (STM704/806) . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Watchdog input (NOT available on STM704/795/806) . . . . . . . . . . . . . . . 14 Backup battery switchover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Chip enable gating (STM795 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Chip enable input (STM795 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Chip enable output (STM795 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Power-fail input/output (NOT available on STM795) . . . . . . . . . . . . . . . . 17 Applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Using a SuperCap™ as a backup power source . . . . . . . . . . . . . . . . . . . 19 Negative-going VCC transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 3 4 5 Typical operating characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Contents 6 7 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Doc ID 10519 Rev 9 3/42 List of tables STM690, STM704, STM795, STM802, STM804, STM805, STM806 List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 I/O status in battery backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 DC and AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SO8 - 8-lead plastic small outline, 150 mils body width, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 TSSOP8 - 8-lead, thin shrink small outline, 3 x 3 mm body size, mechanical data . . . . . . 38 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Marking description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 4/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Logic diagram (STM690/802/804/805) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Logic diagram (STM704/806) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Logic diagram (STM795) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 STM690/802/804/805 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 STM704/806 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 STM795 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Block diagram (STM690/802/804/805) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Block diagram (STM704/806) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Block diagram (STM795) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Hardware hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Chip enable gating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Chip enable waveform (STM795) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Power-fail comparator waveform (STM690/704/802/804/805/806) . . . . . . . . . . . . . . . . . . 18 Using a SuperCap™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 VCC to VOUT on-resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 VBAT to VOUT on-resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Supply current vs. temperature (no load) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Battery current vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 VPFI threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Reset comparator propagation delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Power-up trec vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Normalized reset threshold vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Watchdog time-out period vs. temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 E to ECON on-resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 PFI to PFO propagation delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Output voltage vs. load current (VCC = 5 V; VBAT = 2.8 V; TA = 25 °C) . . . . . . . . . . . . . . . 25 Output voltage vs. load current (VCC = 0 V; VBAT = 2.8 V; TA = 25 °C) . . . . . . . . . . . . . . . 26 RST output voltage vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 RST output voltage vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Power-fail comparator response time (assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Power-fail comparator response time (de-assertion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Maximum transient duration vs. reset threshold overdrive . . . . . . . . . . . . . . . . . . . . . . . . . 28 E to ECON propagation delay vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 E to ECON propagation delay test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 AC testing input/output waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 MR timing waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Watchdog timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 SO8 – 8-lead plastic small outline, 150 mils body width, package mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 TSSOP8 – 8-lead, thin shrink small outline, 3 x 3 mm body size, outline. . . . . . . . . . . . . . 38 Doc ID 10519 Rev 9 5/42 Description STM690, STM704, STM795, STM802, STM804, STM805, STM806 1 Description The STM690/704/795/802/804/805/806 supervisors are self-contained devices which provide microprocessor supervisory functions with the ability to non-volatize and writeprotect external LPSRAM. A precision voltage reference and comparator monitors the VCC input for an out-of-tolerance condition. When an invalid VCC condition occurs, the reset output (RST) is forced low (or high in the case of RST). These devices also offer a watchdog timer (except for STM704/795/806) as well as a power-fail comparator (except for STM795) to provide the system with an early warning of impending power failure. These devices are available in a standard 8-pin SOIC package or a space-saving 8-pin TSSOP package. Figure 1. Logic diagram (STM690/802/804/805) VCC VBAT VOUT WDI PFI STM690/ 802/804/ 805 RST (RST) (1) PFO VSS AI08846 1. For STM804/805, reset output is active-high and open drain. Figure 2. Logic diagram (STM704/806) VCC VBAT VOUT MR PFI STM704 STM806 RST PFO VSS AI08847 6/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Description Figure 3. Logic diagram (STM795) VCC VBAT VOUT VCCSW E ECON STM795 RST VSS AI08848 Table 2. MR WDI RST RST E (1) Signal names Push-button reset input Watchdog input Active-low reset output Active-high reset output Chip enable input Conditioned chip enable output VCC switch output Supply voltage output Supply voltage Backup supply voltage Power-fail input Power-fail output Ground (2) ECON(2) Vccsw(2) VOUT VCC VBAT PFI PFO VSS 2. STM795. 1. Open drain for STM804/805 only. Doc ID 10519 Rev 9 7/42 Description STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 4. STM690/802/804/805 connections SO8/TSSOP8 VOUT VCC VSS PFI 1 2 3 4 8 7 6 5 VBAT RST (RST)(1) WDI PFO AI08849 1. For STM804/805, reset output is active-high and open drain. Figure 5. STM704/806 connections SO8/TSSOP8 VOUT VCC VSS PFI 1 2 3 4 8 7 6 5 V BAT RST MR PFO AI08850 Figure 6. STM795 connections SO8/TSSOP8 VOUT VCC VCCSW VSS 1 2 3 4 8 7 6 5 VBAT RST ECON E AI08851 8/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Description 1.1 1.1.1 Pin descriptions MR (manual reset) A logic low on MR asserts the reset output. Reset remains asserted as long as MR is low and for trec after MR returns high. This active-low input has an internal pull-up. It can be driven from a TTL or CMOS logic line, or shorted to ground with a switch. Leave open if unused. 1.1.2 WDI (watchdog input) If WDI remains high or low for 1.6 s, the internal watchdog timer runs out and reset is triggered. The internal watchdog timer clears while reset is asserted or when WDI sees a rising or falling edge. The watchdog function cannot be disabled by allowing the WDI pin to float. 1.1.3 RST (active-low reset) Pulses low for trec when triggered, and stays low whenever VCC is below the reset threshold or when MR is a logic low. It remains low for trec after either VCC rises above the reset threshold, the watchdog triggers a reset, or MR goes from low to high. 1.1.4 RST (active-high reset - open drain) Pulses high for trec when triggered, and stays high whenever VCC is above the reset threshold or when MR is a logic high. It remains high for trec after either VCC falls below the reset threshold, the watchdog triggers a reset, or MR goes from high to low. 1.1.5 PFI (power-fail input) When PFI is less than VPFI or when VCC falls below VSW (2.4 V), PFO goes low; otherwise, PFO remains high. Connect to ground if unused. 1.1.6 PFO (power-fail output) When PFI is less than VPFI, or VCC falls below VSW, PFO goes low; otherwise, PFO remains high. Leave open if unused. Output type is push-pull. 1.1.7 VOUT (supply output voltage) When VCC is above the switchover voltage (VSO), VOUT is connected to VCC through a P-channel MOSFET switch. When VCC falls below VSO, VBAT connects to VOUT. Connect to VCC if no battery is used. 1.1.8 Vccsw (VCC switch output) When VOUT switches to battery, Vccsw is high. When VOUT switches back to VCC, Vccsw is low. It can be used to drive gate of external PMOS transistor for IOUT requirements exceeding 75 mA. Output type is push-pull. Doc ID 10519 Rev 9 9/42 Description STM690, STM704, STM795, STM802, STM804, STM805, STM806 1.1.9 E (chip enable input) The input to the chip enable gating circuit. Connect to ground if unused. 1.1.10 ECON (conditional chip enable) ECON goes low only when E is low and reset is not asserted. If ECON is low when reset is asserted, ECON will remain low for 15 µs or until E goes high, whichever occurs first. In the disabled mode, ECON is pulled up to VOUT. 1.1.11 VBAT (backup battery input) When VCC falls below VSO, VOUT switches from VCC to VBAT. When VCC rises above VSO + hysteresis, VOUT reconnects to VCC. VBAT may exceed VCC. Connect to VCC if no battery is used. Table 3. Pin description Pin Name Function STM795 — — 7 — — — 1 2 3 4 5 6 8 STM690 STM802 — 6 7 — 4 5 1 2 — 3 — — 8 STM704 STM806 6 — 7 — 4 5 1 2 — 3 — — 8 STM804 STM805 — 6 — 7 4 5 1 2 — 3 — — 8 MR WDI RST RST PFI PFO VOUT VCC Vccsw VSS E ECON VBAT Push-button reset input Watchdog input Active-low reset output Active-high reset output Power-fail input Power-fail output (push-pull) Supply output for external LPSRAM Supply voltage VCC switch output (push-pull) Ground Chip enable input Conditioned chip enable output Backup battery input 10/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 7. V CC V BAT Description Block diagram (STM690/802/804/805) V OUT V SO COMPARE V RST COMPARE WDI WATCHDOG TIMER trec generator (1) RST (RST) PFI V PFI COMPARE PFO AI07897 1. For STM804/805, reset output is active-high and open drain. Figure 8. V CC Block diagram (STM704/806) V OUT V BAT V SO COMPARE V RST COMPARE MR trec generator RST PFI V PFI COMPARE PFO AI07898 Doc ID 10519 Rev 9 11/42 Description Figure 9. V CC V BAT STM690, STM704, STM795, STM802, STM804, STM805, STM806 Block diagram (STM795) V OUT V SO COMPARE V CCSW V RST COMPARE t rec generator RST E CON OUTPUT CONTROL E PFI V PFI COMPARE PFO AI08852 E CON 12/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Description Figure 10. Hardware hookup Regulator Unregulated voltage VIN VCC VCCSW (2) VCC VOUT VCC VCC 0.1 F STM690/704/ 795/802/804/ 805/806 0.1 F WDI (1) LPSRAM E E From microprocessor E(2) R1 PFI (3) R2 Push-button MR (4) RST To microprocessor reset PFO (3) To microprocessor NMI ECON(2) VBAT AI08853 1. For STM690/802/804/805. 2. For STM795 only. 3. Not available on STM795. 4. For STM704/806. Doc ID 10519 Rev 9 13/42 Operation STM690, STM704, STM795, STM802, STM804, STM805, STM806 2 2.1 Operation Reset output The STM690/704/795/802/804/805/806 supervisor asserts a reset signal to the MCU whenever VCC goes below the reset threshold (VRST), a watchdog time-out occurs, or when the push-button reset input (MR) is taken low. RST is guaranteed to be a logic low (logic high for STM804/805) for 0 V < VCC < VRST if VBAT is greater than 1 V. Without a backup battery, RST is guaranteed valid down to VCC = 1 V. During power-up, once VCC exceeds the reset threshold an internal timer keeps RST low for the reset time-out period, trec. After this interval RST returns high. If VCC drops below the reset threshold, RST goes low. Each time RST is asserted, it stays low for at least the reset time-out period (trec). Any time VCC goes below the reset threshold the internal timer clears. The reset timer starts when VCC returns above the reset threshold. 2.2 Push-button reset input (STM704/806) A logic low on MR asserts reset. Reset remains asserted while MR is low, and for trec (see Figure 36) after it returns high. The MR input has an internal 40 kΩ pull-up resistor, allowing it to be left open if not used. This input can be driven with TTL/CMOS-logic levels or with open-drain/ collector outputs. Connect a normally open momentary switch from MR to GND to create a manual reset function; external debounce circuitry is not required. If MR is driven from long cables or the device is used in a noisy environment, connect a 0.1µF capacitor from MR to GND to provide additional noise immunity. MR may float, or be tied to VCC when not used. 2.3 Watchdog input (NOT available on STM704/795/806) The watchdog timer can be used to detect an out-of-control MCU. If the MCU does not toggle the watchdog input (WDI) within tWD (1.6 s typ), the reset is asserted. The internal watchdog timer is cleared by either: 1. 2. a reset pulse, or by toggling WDI (high-to-low or low-to-high), which can detect pulses as short as 50 ns. If WDI is tied high or low, a reset pulse is triggered every 1.8 s (tWD + trec). The timer remains cleared and does not count for as long as reset is asserted. As soon as reset is released, the timer starts counting (see Figure 37). Note: Input frequency greater than 20 ns (50 MHz) will be filtered. 14/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Operation 2.4 Backup battery switchover In the event of a power failure, it may be necessary to preserve the contents of external SRAM through VOUT. With a backup battery installed with voltage VBAT, the devices automatically switch the SRAM to the backup supply when VCC falls. Note: When the battery is first connected without VCC power applied, the device does not immediately provide battery backup voltage on VOUT. Only after VCC exceeds VRST will the switchover operate as described below. This mode allows a battery to be attached during manufacturing but not used until after the system has been activated for the first time. As a result, no battery power is consumed by the device during storage and shipment. If the backup battery is not used, connect both VBAT and VOUT to VCC. This family of supervisors does not always connect VBAT to VOUT when VBAT is greater than VCC. VBAT connects to VOUT (through a 100 Ω switch) when VCC is below VSW (2.4 V) or VBAT (whichever is lower). This is done to allow the backup battery (e.g., a 3.6 V lithium cell) to have a higher voltage than VCC. Assuming that VBAT > 2.0 V, switchover at VSO ensures that battery backup mode is entered before VOUT gets too close to the 2.0 V minimum required to reliably retain data in most external SRAMs. When VCC recovers, hysteresis is used to avoid oscillation around the VSO point. VOUT is connected to VCC through a 3 Ω PMOS power switch. Note: The backup battery may be removed while VCC is valid, assuming VBAT is adequately decoupled (0.1 µF typ), without danger of triggering a reset. Table 4. Pin VOUT VCC PFI PFO E ECON WDI MR RST RST VBAT Vccsw I/O status in battery backup Status Connected to VBAT through internal switch Disconnected from VOUT Disabled Logic low High impedance Logic high Watchdog timer is disabled Disabled Logic low Logic high Connected to VOUT Logic high (STM795) Doc ID 10519 Rev 9 15/42 Operation STM690, STM704, STM795, STM802, STM804, STM805, STM806 2.5 Chip enable gating (STM795 only) Internal gating of the chip enable (E) signal prevents erroneous data from corrupting the external CMOS RAM in the event of an undervoltage condition. The STM795 uses a series transmission gate from E to ECON (see Figure 11). During normal operation (reset not asserted), the E transmission gate is enabled and passes all E transitions. When reset is asserted, this path becomes disabled, preventing erroneous data from corrupting the CMOS RAM. The short E propagation delay from E to ECON enables the STM795 to be used with most µPs. If E is low when reset asserts, ECON remains low for typically 10 µs to permit the current write cycle to complete. 2.6 Chip enable input (STM795 only) The chip enable transmission gate is disabled and E is high impedance (disabled mode) while reset is asserted. During a power-down sequence when VCC passes the reset threshold, the chip enable transmission gate disables and E immediately becomes high impedance if the voltage at E is high. If E is low when reset asserts, the chip enable transmission gate will disable 10 µs after reset asserts (see Figure 12). This permits the current write cycle to complete during power-down. Any time a reset is generated, the chip enable transmission gate remains disabled and E remains high impedance (regardless of E activity) for the first half of the reset time-out period (trec/2). When the chip enable transmission gate is enabled, the impedance of E appears as a 40 Ω resistor in series with the load at ECON. The propagation delay through the chip enable transmission gate depends on VCC, the source impedance of the drive connected to E, and the loading on ECON. The chip enable propagation delay is production tested from the 50% point on E to the 50% point on ECON using a 50 Ω driver and a 50 pF load capacitance (see Figure 35). For minimum propagation delay, minimize the capacitive load at ECON and use a low-output impedance driver. 2.7 Chip enable output (STM795 only) When the chip enable transmission gate is enabled, the impedance of ECON is equivalent to a 40 Ω resistor in series with the source driving E. In the disabled mode, the transmission gate is off and an active pull-up connects ECON to VOUT (see Figure 11). This pull-up turns off when the transmission gate is enabled. Figure 11. Chip enable gating V CC V RST COMPARE trec generator RST V OUT E CON OUTPUT CONTROL E E CON AI08802 16/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 12. Chip enable waveform (STM795) Operation V CC V RST V BAT ½ trec trec ½ trec 10 µs trec E CON RST E AI08855c 2.8 Power-fail input/output (NOT available on STM795) The Power-Fail Input (PFI) is compared to an internal reference voltage (independent from the VRST comparator). If PFI is less than the power-fail threshold (VPFI), the Power-Fail Output (PFO) will go low. This function is intended for use as an undervoltage detector to signal a failing power supply. Typically PFI is connected through an external voltage divider (see Figure 10) to either the unregulated DC input (if it is available) or the regulated output of the VCC regulator. The voltage divider can be set up such that the voltage at PFI falls below VPFI several milliseconds before the regulated VCC input to the STM690/704/795/802/ 804/805/806 or the microprocessor drops below the minimum operating voltage. During battery backup, the power-fail comparator is turned off and PFO goes (or remains) low (see Figure 13). This occurs after VCC drops below VSW (2.4 V). When power returns, the power-fail comparator is enabled and PFO follows PFI. If the comparator is unused, PFI should be connected to VSS and PFO left unconnected. PFO may be connected to MR on the STM704/806 so that a low voltage on PFI will generate a reset output. 2.9 Applications information These supervisor circuits are not short-circuit protected. Shorting VOUT to ground excluding power-up transients such as charging a decoupling capacitor - destroys the device. Decouple both VCC and VBAT pins to ground by placing 0.1 µF capacitors as close to the device as possible. Doc ID 10519 Rev 9 17/42 Operation STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 13. Power-fail comparator waveform (STM690/704/802/804/805/806) V CC V RST V SW (2.4 V ) trec PFO PFO follows PFI PFO follows PFI RST AI08861a 18/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Operation 2.10 Using a SuperCap™ as a backup power source SuperCaps™ are capacitors with extremely high capacitance values (e.g., order of 0.47 F) for their size. Figure 14 shows how to use a SuperCap as a backup power source. The SuperCap may be connected through a diode to the VCC supply. Since VBAT can exceed VCC while VCC is above the reset threshold, there are no special precautions when using these supervisors with a Super-Cap. Figure 14. Using a SuperCap™ 5V VCC VOUT To external SRAM STMXXX VBAT GND RST To µP AI08805 2.11 Negative-going VCC transients The STM690/704/795/802/804/805/806 supervisors are relatively immune to negative-going VCC transients (glitches). Figure 32 was generated using a negative pulse applied to VCC, starting at VRST + 0.3 V and ending below the reset threshold by the magnitude indicated (comparator overdrive). The graph indicates the maximum pulse width a negative VCC transient can have without causing a reset pulse. As the magnitude of the transient increases (further below the threshold), the maximum allowable pulse width decreases. Any combination of duration and overdrive which lies under the curve will NOT generate a reset signal. Typically, a VCC transient that goes 100 mV below the reset threshold and lasts 40 µs or less will not cause a reset pulse. A 0.1 µF bypass capacitor mounted as close as possible to the VCC pin provides additional transient immunity. Doc ID 10519 Rev 9 19/42 Typical operating characteristics STM690, STM704, STM795, STM802, STM804, STM805, STM806 3 Note: Typical operating characteristics Typical values are at TA = 25 °C. Figure 15. VCC to VOUT on-resistance vs. temperature 5.0 4.0 VCC = 3.0 V VCC = 4.5 V VCC = 5.5 V on-resistance ( V CC to V OUT ) 3.0 2.0 1.0 0.0 –40 –20 0 20 40 60 80 100 120 AI10498 Temperature (°C) Figure 16. VBAT to VOUT on-resistance vs. temperature 160 V BAT to V OUT on-resistance ( ) 140 120 100 80 60 40 20 0 –40 –20 0 20 40 Temperature (°C) AI09140b VBAT = 2.0 V VBAT = 3.0 V VBAT = 3.3 V VBAT = 3.6 V 60 80 100 120 20/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Typical operating characteristics Figure 17. Supply current vs. temperature (no load) 30 25 20 Supply current ( µ A) 15 VCC = 2.7 V VCC = 3.0 V VCC = 3.6 V VCC = 4.5 V VCC = 5.5 V 10 5 0 –40 –20 0 20 40 Temperature (°C) 60 80 100 120 AI09141b Figure 18. Battery current vs. temperature 1000 Battery supply current (nA) 100 VBAT = 2.0 V VBAT = 3.0 V VBAT = 3.6 V 10 1 0.1 –40 –20 0 20 40 Tempe r ature (°C) 60 80 100 120 AI10499 Doc ID 10519 Rev 9 21/42 Typical operating characteristics STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 19. VPFI threshold vs. temperature 1.270 1.265 1.260 V PFI threshold (V) 1.255 1.250 1.245 1.240 1.235 1.230 1.225 –40 VCC = 2.5 V VCC = 3.0 V VCC = 3.3 V VCC = 3.6 V –20 0 20 40 Temperature (°C) 60 80 100 120 AI09142b Figure 20. Reset comparator propagation delay vs. temperature 30 28 26 Propagation delay (µs) 24 22 20 18 16 14 12 10 –40 –20 0 20 40 Temperature (°C) AI09143b 60 80 100 120 22/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Typical operating characteristics Figure 21. Power-up trec vs. temperature 240 235 230 t rec (ms) VCC = 3.0 V 225 VCC = 4.5 V VCC = 5.5 V 220 215 210 –40 –20 0 20 40 60 Temperature (°C) 80 100 120 AI09144b Figure 22. Normalized reset threshold vs. temperature 1.004 Normalized reset threshold 1.002 1.000 0.998 0.996 –40 –20 0 20 40 Temperature (°C) 60 80 100 120 AI09145b Doc ID 10519 Rev 9 23/42 Typical operating characteristics STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 23. Watchdog time-out period vs. temperature 1.90 1.85 Watchdog time-out period (s) 1.80 1.75 VCC = 3.0 V VCC = 4.5 V VCC = 5.5 V 1.70 1.65 1.60 –40 –20 0 20 40 Tempe rature (°C) 60 80 100 120 AI09146b Figure 24. E to ECON on-resistance vs. temperature 60 50 E to E CON on-resistance ( ) 40 30 20 VCC = 3.0 V VCC = 4.5 V VCC = 5.5 V 10 0 –40 –20 0 20 40 Temper ature (°C) 60 80 100 120 AI09147b 24/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Typical operating characteristics Figure 25. PFI to PFO propagation delay vs. temperature 4.0 VCC = 3.0 V PFI to PFO propagation delay (µs) 3.0 VCC = 3.6 V VCC = 4.5 V VCC = 5.5 V 2.0 1.0 0.0 –40 –20 0 20 40 Temperature (°C) 60 80 100 120 AI09148b Figure 26. Output voltage vs. load current (VCC = 5 V; VBAT = 2.8 V; TA = 25 °C) 5.00 4.98 V OUT (V) 4.96 4.94 0 10 20 I OUT (mA) 30 40 50 AI10496 Doc ID 10519 Rev 9 25/42 Typical operating characteristics STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 27. Output voltage vs. load current (VCC = 0 V; VBAT = 2.8 V; TA = 25 °C) 2.80 2.78 2.76 V OUT (V) 2.74 2.72 2.70 2.68 2.66 0.0 0.2 0.4 I OUT (mA) 0.6 0.8 1.0 AI10497 Figure 28. RST output voltage vs. supply voltage 5 VRST VCC 4 5 4 V RST (V) 2 2 1 1 0 500 ms / div 0 AI09149b 26/42 Doc ID 10519 Rev 9 V CC (V) 3 3 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Typical operating characteristics Figure 29. RST output voltage vs. supply voltage 5 V RST VCC 5 4 4 V RST (V) 2 2 1 1 0 500 ms / div 0 AI09150b Figure 30. Power-fail comparator response time (assertion) 5V PFO 1 V / div 0V 1.3 V PFI 500 mV / div 0V 500 ns / div AI09153b Doc ID 10519 Rev 9 V CC (V) 3 3 27/42 Typical operating characteristics STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 31. Power-fail comparator response time (de-assertion) 5V PFO 1 V / div 0V 1.3 V PFI 500 mV / div 0V 500 ns / div AI09154b Figure 32. Maximum transient duration vs. reset threshold overdrive 6000 5000 Transient duration (µs) 4000 Reset occurs above the curve 3000 2000 1000 0 0.001 0.01 0.1 1 10 AI09156b Reset comparator overdrive, V RST – V CC (V) 28/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Typical operating characteristics Figure 33. E to ECON propagation delay vs. temperature 4.0 E to ECON propagation delay (ns) 3.0 2.0 1.0 VCC = 3.0 V VCC = 4.5 V VCC = 5.5 V 0.0 –40 –20 0 20 40 Temperature (°C) 60 80 100 120 AI09157b Doc ID 10519 Rev 9 29/42 Maximum ratings STM690, STM704, STM795, STM802, STM804, STM805, STM806 4 Maximum ratings Stressing the device above the rating listed in the absolute maximum ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 5. Symbol TSTG TSLD(1) VIO VCC/VBAT IO PD Absolute maximum ratings Parameter Storage temperature (VCC off) Lead solder temperature for 10 seconds Input or output voltage Supply voltage Output current Power dissipation Value –55 to 150 260 –0.3 to VCC +0.3 –0.3 to 6.0 20 320 Unit °C °C V V mA mW 1. Reflow at peak temperature of 260 °C. The time above 255 °C must not exceed 30 seconds. 30/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 DC and AC parameters 5 DC and AC parameters This section summarizes the operating measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristics tables that follow, are derived tests performed under the measurement conditions summarized in Table 6. Designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. Table 6. Operating and AC measurement conditions Parameter VCC/VBAT supply voltage Ambient operating temperature (TA) Input rise and fall times Input pulse voltages Input and output timing ref. voltages STM690/704/795/ 802/804/805/806 1.0 to 5.5 –40 to 85 ≤ 55 0.2 to 0.8 VCC 0.3 to 0.7 VCC Unit V °C ns V V Figure 34. E to ECON propagation delay test circuit VCC VCC VBAT 3.6 V 25 equivalent source impedance STM690/704/ 795/802/804/ 805/806 E ECON 50 pF C L(1) 50 50 cable 50 GND AI08854 1. CL includes load capacitance and scope probe capacitance. Figure 35. AC testing input/output waveforms 0.8 V CC 0.7 V CC 0.3 V CC AI02568 0.2 V CC Doc ID 10519 Rev 9 31/42 DC and AC parameters STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 36. MR timing waveform MR tMLRL RST (1) tMLMH trec AI07837a 1. RST for STM805. Figure 37. Watchdog timing VCC trec tWD WDI AI07891 RST Table 7. Sym VCC, VBAT(2) DC and AC characteristics Alternative Description Test condition(1) Min 1.1(3) 40 35 25 0.4 VCC – 0.03 VCC – 0.3 VCC – 0.015 VCC – 0.15 Typ Max Unit Operating voltage TA = –40 to +85 °C Excluding IOUT (VCC < 5.5 V) Excluding IOUT (VCC < 3.6 V) Excluding IOUT (VBAT = 2.3 V, VCC = 2.0 V, MR = VCC) Excluding IOUT (VBAT = 3.6 V) IOUT1 = 5 mA(5) 5.5 60 50 35 1.0 V µA µA µA µA V V V V V VCC supply current ICC VCC supply current in battery backup mode IBAT(4) VBAT supply current in battery backup mode VOUT1 VOUT voltage (active) IOUT1 = 75 mA IOUT1 = 250 µA, VCC > 2.5 V(5) IOUT2 = 250 µA, VBAT = 2.3 V VCC – VCC – 0.0015 0.0006 VBAT – VBAT – 0.1 0.034 VBAT – 0.14 3 4 VOUT2 VOUT voltage (battery backup) IOUT2 = 1 mA, VBAT = 2.3 V VCC to VOUT on-resistance Ω 32/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Table 7. Sym DC and AC parameters DC and AC characteristics (continued) Alternative Description VBAT to VOUT on-resistance Input leakage current (MR) STM704/806 only; MR = 0 V, VCC = 3 V 0 V < VIN < VCC 0 V < VIN < VCC STM804/805/795; 0 V < VIN < VCC(6) VRST (max) < VCC < 5.5 V VRST (max) < VCC < 5.5 V VCC = VRST (max), ISINK = 3.2 mA VCC = VRST (max), IOUT = 1.6 mA, E = 0 V IOL = 40 µA, VCC = 1.0 V, VBAT = VCC, TA = 0 °C to 85 °C IOL = 200 µA, VCC = 1.2 V, VBAT = VCC Output high voltage (RST, RST)(7) ISOURCE = 1 mA, VCC = VRST (max) VCC = VRST (max), IOUT = 1.6 mA, E = VCC ISOURCE = 75 µA, VCC = VRST (max) ISOURCE = 100 µA, VCC = 0 V, VBAT = 2.8 V ISOURCE = 75 µA, VCC = 0 V, VBAT = 2.8 V 2.4 0.8 VCC 0.8 VCC 0.8 VBAT 0.8 VBAT 20 –20 –1 –1 0.7 VCC 0.3 VCC 0.3 Test condition(1) Min Typ 100 75 2 350 +25 +1 +1 Max Unit Ω µA nA µA µA V V V ILI Input leakage current (PFI) Input leakage current (WDI) ILO Output leakage current Input high voltage (MR, WDI) Input low voltage (MR, WDI) Output low voltage (PFO, RST, RST, Vccsw) VIH VIL VOL Output low voltage (ECON) 0.2 VCC V 0.3 V VOL Output low voltage (RST) 0.3 V V V V V V VOH Output high voltage (ECON) Output high voltage (PFO) VOH battery backup (Vccsw, RST) VOHB VOH battery backup (ECON) Power-fail comparator (NOT available on STM795) VPFI PFI input threshold PFI falling (VCC < 3.6 V) STM802/ 804/806 STM690/ 704/805 1.212 1.187 1.237 1.237 10 2 1.262 1.287 20 V V mV µs PFI hysteresis tPFD PFI to PFO propagation delay PFI rising (VCC < 3.6 V) Doc ID 10519 Rev 9 33/42 DC and AC parameters Table 7. Sym STM690, STM704, STM795, STM802, STM804, STM805, STM806 DC and AC characteristics (continued) Alternative Description PFO output short to GND current Test condition(1) Min Typ Max Unit ISC VCC = 3.6 V, PFO = 0 V 0.1 0.75 2.0 mA Battery switchover Power-down Battery backup switchover voltage(8)(9) VSO VSW Hysteresis Reset thresholds VCC falling STM690T/ 704T/795T/ 805T V rising CC STM802T/ 804T/806T VCC falling VCC rising 3.00 3.00 3.00 3.00 2.85 2.85 2.88 2.88 2.55 2.55 2.59 2.59 140 3.075 3.085 3.075 3.085 2.925 2.935 2.925 2.935 2.625 2.635 2.625 2.635 200 3.15 3.17 3.12 3.14 3.00 3.02 3.00 3.02 2.70 2.72 2.70 2.72 280 V V V V V V V V V V V V ms Power-up VBAT > VSW VBAT < VSW VBAT > VSW VBAT < VSW VSW VBAT VSW VBAT 2.4 40 V V V V V mV VRST(10) Reset threshold VCC falling STM690S/ 704S/795S/ 805S V rising CC STM802S/ 804S/806S VCC falling VCC rising VCC falling STM690R/ 704R/795R/ 805R V rising CC STM802R/ 804R/806R trec RST pulse width VCC falling VCC rising VCC < 3.6 V Push-button reset input (STM704/806) tMLMH tMLRL tMR MR pulse width 100 20 60 500 ns ns tMRD MR to RST output delay Watchdog timer (NOT available on STM704/795/806) tWD Watchdog timeout period WDI pulse width Chip enable gating (STM795 only) E to ECON resistance VCC = VRST (max) 46 Ω VRST (max) < VCC < 3.6 V VRST (max) < VCC < 3.6 V 1.12 100 1.60 20 2.24 s ns 34/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Table 7. Sym DC and AC parameters DC and AC characteristics (continued) Alternative Description E to ECON propagation delay Reset to ECON high delay Test condition(1) VCC = VRST (max) Min Typ 2 10 VCC = 3.6 V, disable mode, ECON = 0 V 0.1 0.75 2.0 Max 7 Unit ns µs mA ISC ECON short circuit current 1. Valid for ambient operating temperature: TA = –40 to 85 °C; VCC = VRST (max) to 5.5 V; and VBAT = 2.8 V (except where noted). 2. VCC supply current, logic input leakage, watchdog functionality, push-button reset functionality, PFI functionality, state of RST and RST tested at VBAT = 3.6 V, and VCC = 5.5 V. The state of RST or RST and PFO is tested at VCC = VCC (min). Either VCC or VBAT can go to 0 V if the other is greater than 2.0 V. 3. VCC (min) = 1.0 V for TA = 0 °C to +85 °C. 4. Tested at VBAT = 3.6 V, VCC = 3.5 V and 0 V. 5. Guaranteed by design. 6. The leakage current measured on the RST pin (STM804/805) or RST pin (STM795) is tested with the reset output not asserted (output high impedance). 7. Not valid for STM795/804/805 (open drain). 8. When VBAT > VCC > VSW, VOUT remains connected to VCC until VCC drops below VSW. 9. When VSW > VCC > VBAT, VOUT remains connected to VCC until VCC drops below the battery voltage (VBAT) - 75 mV. 10. The reset threshold tolerance is wider for VCC rising than for VCC falling due to the 10 mV (typ) hysteresis, which prevents internal oscillation. Doc ID 10519 Rev 9 35/42 Package mechanical data STM690, STM704, STM795, STM802, STM804, STM805, STM806 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 36/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Package mechanical data Figure 38. SO8 – 8-lead plastic small outline, 150 mils body width, package mechanical drawing A2 B e D A C ddd 8 E 1 H A1 L SO-A Table 8. SO8 - 8-lead plastic small outline, 150 mils body width, package mechanical data mm inches Max 1.75 0.25 0.51 0.25 5.00 0.10 4.00 — 6.20 0.50 0.90 8° Typ — — — — — — — 0.050 — — — — Min 0.053 0.004 0.013 0.007 0.189 — 0.150 — 0.228 0.010 0.016 0° 8 Max 0.069 0.010 0.020 0.010 0.197 0.004 0.157 — 0.244 0.020 0.035 8° Symb Typ A A1 B C D ddd E e H h L α N — — — — — — — 1.27 — — — — Min 1.35 0.10 0.33 0.19 4.80 — 3.80 — 5.80 0.25 0.40 0° 8 Doc ID 10519 Rev 9 37/42 Package mechanical data STM690, STM704, STM795, STM802, STM804, STM805, STM806 Figure 39. TSSOP8 – 8-lead, thin shrink small outline, 3 x 3 mm body size, outline D 8 5 E1 E c 1 4 A1 A CP b e A2 L L1 TSSOP8BM Table 9. TSSOP8 - 8-lead, thin shrink small outline, 3 x 3 mm body size, mechanical data mm inches Max 1.10 0.15 0.95 0.40 0.23 0.10 3.10 — 5.15 3.10 0.70 — 6° Typ — — 0.034 — — — 0.118 0.026 0.193 0.118 0.022 0.037 — Min — 0.002 0.030 0.010 0.005 — 0.114 — 0.183 0.114 0.016 — 0° Max 0.043 0.006 0.037 0.016 0.009 0.004 0.122 — 0.203 0.122 0.030 — 6° Symb Typ A A1 A2 b c CP D e E E1 L L1 α N — — 0.85 — — — 3.00 0.65 4.90 3.00 0.55 0.95 — 8 Min — 0.05 0.75 0.25 0.13 — 2.90 — 4.65 2.90 0.40 — 0° 8 38/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Part numbering 7 Part numbering Table 10. Example: Device type STM690/704/795/802/804/805/806 Ordering information scheme STM690 T M 6 E Reset threshold voltage T = STM690/704/795/805 = VRST = 3.00 V to 3.15 V STM802/804/806 = VRST = 3.00 V to 3.12 V S = STM690/704/795/805 = VRST = 2.85 V to 3.00 V STM802/804/806 = VRST = 2.88 V to 3.00 V R = STM690/704/795/805 = VRST = 2.55 V to 2.70 V STM802/804/806 = VRST = 2.59 V to 2.70 V Package M = SO8 DS(1)= TSSOP8 Temperature range 6 = –40 to 85 °C Shipping method E = ECOPACK® package, tubes F = ECOPACK® package, tape and reel 1. Contact local ST sales office for availability. For other options, or for more information on any aspect of this device, please contact the ST sales office nearest you. Doc ID 10519 Rev 9 39/42 Part numbering Table 11. STM690, STM704, STM795, STM802, STM804, STM805, STM806 Marking description Reset threshold 3.075 2.925 2.625 3.075 2.925 2.625 3.075 2.925 2.625 3.075 2.925 2.625 3.075 2.925 2.625 3.075 2.925 2.625 3.075 2.925 2.625 Package SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 SO8 TSSOP8 Topside marking 690T 690S 690R 704T 704S 704R 795T 795S 795R 802T 802S 802R 804T 804S 804R 805T 805S 805R 806T 806S 806R Part number STM690T STM690S STM690R STM704T STM704S STM704R STM795T STM795S STM795R STM802T STM802S STM802R STM804T STM804S STM804R STM805T STM805S STM805R STM806T STM806S STM806R 40/42 Doc ID 10519 Rev 9 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Revision history 8 Revision history Table 12. Date 31-Oct-2003 22-Dec-2003 16-Jan-2004 07-Apr-2004 25-May-2004 02-Jul-2004 29-Sep-2004 25-Feb-2005 05-Apr-2006 20-Nov-2009 18-Aug-2010 Document revision history Revision 1 2 2.1 2.2 3 4 5 6 7 8 9 Initial release. Reformatted; update characteristics (Figure 1, 3, 4, 11, 13, 14, 37; Table 1, 3, 4, 7, 9, 11). Added Typical operating characteristics (Figure 17, 18, 20 to 26, 29, 30 to 34). Updated characteristics (Figure 13, 29, 30, Table 1, 3, 7) Update characteristics (Table 3, 7) Update package availability, pin description; promote document (Figure 1, 14; Table 3, 10) Clarify root part numbers, pin descriptions, update characteristics (Figure 2, to, 11, 13, 14, 35; Table 1, 3, 6, 7, 10) Update characteristics (Figure 11, 16, to 35; Table 7) Update characteristics (Figure 13) Updated Section 1.1.6, Section 1.1.8, Figure 10, 11, 19, Table 3, 5, 7; added text to Section 6. Updated Features, Section 2.4: Backup battery switchover. Changes Doc ID 10519 Rev 9 41/42 STM690, STM704, STM795, STM802, STM804, STM805, STM806 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 42/42 Doc ID 10519 Rev 9