STM8L052R8
Value Line, 8-bit ultralow power MCU, 64-KB Flash,
256-byte data EEPROM, RTC, LCD, timers, USART, I2C, SPI, ADC
Datasheet - production data
Features
• Operating conditions
– Operating power supply: 1.8 V to 3.6 V
– Temperature range: -40 °C to 85 °C
• Low power features
– 5 low power modes: Wait, Low power run
(5.9 µA), Low power wait (3 µA), Active-halt
with full RTC (1.4 µA), Halt (400 nA)
– Dynamic power consumption:
200 µA/MHz + 330 µA
– Ultra-low leakage per I/0: 50 nA
– Fast wakeup from Halt: 4.7 µs
• Advanced STM8 core
– Harvard architecture and 3-stage pipeline
– Max freq. 16 MHz, 16 CISC MIPS peak
– Up to 40 external interrupt sources
• Reset and supply management
– Low power, ultra-safe BOR reset with 5
programmable thresholds
– Ultra low power POR/PDR
– Programmable voltage detector (PVD)
LQFP64
• DMA
– 4 channels supporting ADC, SPIs, I2C,
USARTs, timers
– 1 channel for memory-to-memory
• 12-bit ADC up to 1 Msps/27 channels
– Internal reference voltage
• Timers
– Three 16-bit timers with 2 channels (used
as IC, OC, PWM), quadrature encoder
– One 16-bit advanced control timer with 3
channels, supporting motor control
– One 8-bit timer with 7-bit prescaler
– 2 watchdogs: 1 Window, 1 Independent
– Beeper timer with 1, 2 or 4 kHz frequencies
• Clock management
– 32 kHz and 1 to 16 MHz crystal oscillators
– Internal 16 MHz factory-trimmed RC
– 38 kHz low consumption RC
– Clock security system
• Communication interfaces
– Two synchronous serial interfaces (SPI)
– Fast I2C 400 kHz SMBus and PMBus
– Three USARTs (ISO 7816 interface + IrDA)
• Low power RTC
– BCD calendar with alarm interrupt
– Digital calibration with +/- 0.5ppm accuracy
– Advanced anti-tamper detection
• Development support
– Fast on-chip programming and nonintrusive debugging with SWIM
– Bootloader using USART
• Up to 54 I/Os, all mappable on interrupt vectors
• LCD: 8x24 or 4x28 w/ step-up converter
• Memories
– 64 KB Flash program memory and 256
bytes data EEPROM with ECC, RWW
– Flexible write and read protection modes
– 4 KB of RAM
April 2019
This is information on a product in full production.
DS9111 Rev 4
1/112
www.st.com
Contents
STM8L052R8
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3
2.1
Device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2
Ultra low power continuum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Functional overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.1
Low power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2
Central processing unit STM8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3
Advanced STM8 Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2.2
Interrupt controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reset and supply management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3.1
Power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3.2
Power supply supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3.3
Voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.4
Clock management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.5
Low power real-time clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.6
LCD (Liquid crystal display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.7
Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.8
DMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.9
Analog-to-digital converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.10
System configuration controller and routing interface . . . . . . . . . . . . . . . 19
3.11
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3.12
2/112
3.2.1
3.11.1
TIM1 - 16-bit advanced control timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.11.2
16-bit general purpose timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.11.3
8-bit basic timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Watchdog timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.12.1
Window watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.12.2
Independent watchdog timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.13
Beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.14
Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.14.1
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.14.2
I²C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DS9111 Rev 4
STM8L052R8
Contents
3.14.3
4
3.15
Infrared (IR) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.16
Development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1
5
USART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
System configuration options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Memory and register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.1
Memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.2
Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6
Interrupt vector mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
7
Option bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
8
Electrical parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.1
Parameter conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.1.1
Minimum and maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.1.2
Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.1.3
Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.1.4
Loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.1.5
Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
8.2
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
8.3
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
8.4
8.3.1
General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
8.3.2
Embedded reset and power control block characteristics
8.3.3
Supply current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
8.3.4
Clock and timing characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
8.3.5
Memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
8.3.6
I/O current injection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
8.3.7
I/O port pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
8.3.8
Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
8.3.9
LCD controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
8.3.10
Embedded reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
8.3.11
12-bit ADC1 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
8.3.12
EMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
. . . . . . . . . . 60
Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
DS9111 Rev 4
3/112
4
Contents
9
STM8L052R8
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
9.1
LQFP64 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
10
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
4/112
DS9111 Rev 4
STM8L052R8
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
Table 23.
Table 24.
Table 25.
Table 26.
Table 27.
Table 28.
Table 29.
Table 30.
Table 31.
Table 32.
Table 33.
Table 34.
Table 35.
Table 36.
Table 37.
Table 38.
Table 39.
Table 40.
Table 41.
Table 42.
Table 43.
Table 44.
Table 45.
High density value line STM8L05xxx low power device features and
peripheral counts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Timer feature comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Legend/abbreviation for Table 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
High density value line STM8L05xxx pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Flash and RAM boundary addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
I/O port hardware register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
General hardware register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
CPU/SWIM/debug module/interrupt controller registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Interrupt mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Option byte addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Option byte description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Embedded reset and power control block characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . 60
Total current consumption in Run mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Total current consumption in Wait mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Total current consumption and timing in Low power run mode at VDD = 1.8 V to
3.6 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Total current consumption in Low power wait mode at VDD = 1.8 V to 3.6 V . . . . . . . . . . 70
Total current consumption and timing in Active-halt mode
at VDD = 1.8 V to 3.6 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Typical current consumption in Active-halt mode, RTC clocked by LSE external crystal . . 72
Total current consumption and timing in Halt mode at VDD = 1.8 to 3.6 V . . . . . . . . . . . . 74
Peripheral current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Current consumption under external reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
HSE external clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
LSE external clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
HSE oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
LSE oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
HSI oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
LSI oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
RAM and hardware registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Flash program and data EEPROM memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
I/O current injection susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
I/O static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Output driving current (high sink ports). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Output driving current (true open drain ports). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Output driving current (PA0 with high sink LED driver capability). . . . . . . . . . . . . . . . . . . . 87
NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
SPI1 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
I2C characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
LCD characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Reference voltage characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
ADC1 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
ADC1 accuracy with VDDA = 3.3 V to 2.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
DS9111 Rev 4
5/112
6
List of tables
Table 46.
Table 47.
Table 48.
Table 49.
Table 50.
Table 51.
Table 52.
Table 53.
Table 54.
6/112
STM8L052R8
ADC1 accuracy with VDDA = 2.4 V to 3.6 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
ADC1 accuracy with VDDA = VREF+ = 1.8 V to 2.4 V . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
EMS data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
EMI data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
ESD absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Electrical sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
LQFP64 – 10 x 10 mm, 64-pin low-profile quad flat package mechanical data . . . . . . . . 108
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
DS9111 Rev 4
STM8L052R8
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
Figure 43.
Figure 44.
High density value line STM8L05xxx device block diagram . . . . . . . . . . . . . . . . . . . . . . 12
High density value line STM8L05xxx clock tree diagram . . . . . . . . . . . . . . . . . . . . . . . . . 17
STM8L052R8 64-pin LQFP64 package pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Pin loading conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Power supply thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Typical IDD(RUN) from RAM vs. VDD (HSI clock source), fCPU =16 MHz 1) . . . . . . . . . . . . . 65
Typical IDD(RUN) from Flash vs. VDD (HSI clock source), fCPU = 16 MHz1) . . . . . . . . . . . . 65
Typical IDD(Wait) from RAM vs. VDD (HSI clock source), fCPU = 16 MHz 1) . . . . . . . . . . . . . 67
Typical IDD(Wait) from Flash (HSI clock source), fCPU = 16 MHz 1) . . . . . . . . . . . . . . . . . . . 67
Typical IDD(LPR) vs. VDD (LSI clock source), all peripherals OFF . . . . . . . . . . . . . . . . . . . . 69
Typical IDD(LPW) vs. VDD (LSI clock source), all peripherals OFF (1) . . . . . . . . . . . . . . . . . 70
Typical IDD(AH) vs. VDD (LSI clock source) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Typical IDD(Halt) vs. VDD (internal reference voltage OFF) . . . . . . . . . . . . . . . . . . . . . . . . 74
HSE oscillator circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
LSE oscillator circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Typical HSI frequency vs. VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Typical LSI clock source frequency vs. VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Typical VIL and VIH vs. VDD (standard I/Os) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Typical VIL and VIH vs. VDD (true open drain I/Os). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Typical pull-up resistance RPU vs. VDD with VIN=VSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Typical pull-up current Ipu vs. VDD with VIN=VSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Typical VOL @ VDD = 3.0 V (high sink ports) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Typical VOL @ VDD = 1.8 V (high sink ports) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Typical VOL @ VDD = 3.0 V (true open drain ports) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Typical VOL @ VDD = 1.8 V (true open drain ports) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Typical VDD - VOH @ VDD = 3.0 V (high sink ports). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Typical VDD - VOH @ VDD = 1.8 V (high sink ports). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Typical NRST pull-up resistance RPU vs. VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Typical NRST pull-up current Ipu vs. VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Recommended NRST pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
SPI1 timing diagram - slave mode and CPHA=0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
SPI1 timing diagram - slave mode and CPHA=1(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
SPI1 timing diagram - master mode(1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Typical application with I2C bus and timing diagram 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
ADC1 accuracy characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Typical connection diagram using the ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Power supply and reference decoupling (VREF+ not connected to VDDA). . . . . . . . . . . . . 103
Power supply and reference decoupling (VREF+ connected to VDDA) . . . . . . . . . . . . . . 103
LQFP64 – 10 x 10 mm, 64 pin low-profile quad flat package outline . . . . . . . . . . . . . . . . 107
Recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Example of package marking (package top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
DS9111 Rev 4
7/112
7
Introduction
1
STM8L052R8
Introduction
This document describes the features, pinout, mechanical data and ordering information of
the high density value line STM8L052R8 microcontroller with a Flash memory density of
64 Kbytes.
For further details on the whole STMicroelectronics high density family please refer to
Section 2.2: Ultra low power continuum.
For detailed information on device operation and registers, refer to the reference manual
(RM0031).
For information on to the Flash program memory and data EEPROM, refer to the
programming manual (PM0054).
For information on the debug module and SWIM (single wire interface module), refer to the
STM8 SWIM communication protocol and debug module user manual (UM0470).
For information on the STM8 core, refer to the STM8 CPU programming manual (PM0044).
High density value line devices provide the following benefits:
•
Integrated system
–
64 Kbytes of high density embedded Flash program memory
–
256 bytes of data EEPROM
–
4 Kbytes of RAM
–
Internal high speed and low-power low speed RC
–
Embedded reset
•
Ultra low power consumption
–
1 µA in Active-halt mode
–
Clock gated system and optimized power management
–
Capability to execute from RAM for Low power wait mode and low power run
mode
•
Advanced features
–
Up to 16 MIPS at 16 MHz CPU clock frequency
–
Direct memory access (DMA) for memory-to-memory or peripheral-to-memory
access
•
Short development cycles
–
Application scalability across a common family product architecture with
compatible pinout, memory map and modular peripherals
–
Wide choice of development tools
These features make the value line STM8L05xxx ultra low power microcontroller family
suitable for a wide range of consumer and mass market applications.
Refer to Table 1: High density value line STM8L05xxx low power device features and
peripheral counts and Section 3: Functional overview for an overview of the complete range
of peripherals proposed in this family.
Figure 1 shows the block diagram of the high density value line STM8L05xxx family.
8/112
DS9111 Rev 4
STM8L052R8
2
Description
Description
The high density value line STM8L05xxx devices are members of the STM8L ultra low
power 8-bit family.
The value line STM8L05xxx ultra low power family features the enhanced STM8 CPU core
providing increased processing power (up to 16 MIPS at 16 MHz) while maintaining the
advantages of a CISC architecture with improved code density, a 24-bit linear addressing
space and an optimized architecture for low power operations.
The family includes an integrated debug module with a hardware interface (SWIM) which
allows non-intrusive In-application debugging and ultra-fast Flash programming.
High density value line STM8L05xxx microcontrollers feature embedded data EEPROM and
low-power, low-voltage, single-supply program Flash memory.
All devices offer 12-bit ADC, real-time clock, four 16-bit timers, one 8-bit timer as well as
standard communication interface such as two SPIs, I2C, three USARTs and 8x24 or 4x28segment LCD. The 8x24 or 4x 28-segment LCD is available on the high density value line
STM8L05xxx.
The STM8L05xxx family operates from 1.8 V to 3.6 V and is available in the -40 to +85 °C
temperature range.
The modular design of the peripheral set allows the same peripherals to be found in
different ST microcontroller families including 32-bit families. This makes any transition to a
different family very easy, and simplified even more by the use of a common set of
development tools.
All value line STM8L ultra low power products are based on the same architecture with the
same memory mapping and a coherent pinout.
DS9111 Rev 4
9/112
52
Description
2.1
STM8L052R8
Device overview
Table 1. High density value line STM8L05xxx low power device features and
peripheral counts
Features
STM8L052R8
Flash (Kbytes)
64
Data EEPROM (bytes)
256
RAM (Kbytes)
4
LCD
Timers
8x24 or 4x28
Basic
1
(8-bit)
General purpose
3
(16-bit)
Advanced control
1
(16-bit)
SPI
Communication
I2C
interfaces
USART
2
1
3
GPIOs
54(1)
12-bit synchronized ADC
(number of channels)
1
(26)
Others
RTC, window watchdog, independent watchdog,
16-MHz and 38-kHz internal RC,
1- to 16-MHz and 32-kHz external oscillator
CPU frequency
16 MHz
Operating voltage
1.8 V to 3.6 V
Operating temperature
-40 to +85 °C
Package
LQFP64
1. The number of GPIOs given in this table includes the NRST/PA1 pin but the application can use the
NRST/PA1 pin as general purpose output only (PA1).
10/112
DS9111 Rev 4
STM8L052R8
2.2
Description
Ultra low power continuum
The ultra low power value line STM8L05xxx and STM8L15xxx are fully pin-to-pin, software
and feature compatible. Besides the full compatibility within the STM8L family, the devices
are part of STMicroelectronics microcontrollers ultra low power strategy which also includes
STM8L101xx and STM32L15xxx. The STM8L and STM32L families allow a continuum of
performance, peripherals, system architecture, and features.
They are all based on STMicroelectronics 0.13 µm ultra-low leakage process.
Note:
1
The STM8L05xxx is pin-to-pin compatible with STM8L101xx devices.
2
The STM32L family is pin-to-pin compatible with the general purpose STM32F family.
Please refer to STM32L15x documentation for more information on these devices.
Performance
All families incorporate highly energy-efficient cores with both Harvard architecture and
pipelined execution: advanced STM8 core for STM8L families and ARM Cortex™-M3 core
for STM32L family. In addition specific care for the design architecture has been taken to
optimize the mA/DMIPS and mA/MHz ratios.
This allows the ultra low power performance to range from 5 up to 33.3 DMIPs.
Shared peripherals
STM8L05x, STM8L15x and STM32L15xx share identical peripherals which ensure a very
easy migration from one family to another:
•
Analog peripheral: ADC1
•
Digital peripherals: RTC and some communication interfaces
Common system strategy
To offer flexibility and optimize performance, the STM8L and STM32L devices use a
common architecture:
•
Same power supply range from 1.8 to 3.6 V
•
Architecture optimized to reach ultra-low consumption both in low power modes and
Run mode
•
Fast startup strategy from low power modes
•
Flexible system clock
•
Ultra-safe reset: same reset strategy for both STM8L and STM32L including power-on
reset, power-down reset, brownout reset and programmable voltage detector
Features
ST ultra low power continuum also lies in feature compatibility:
•
More than 10 packages with pin count from 20 to 100 pins and size down to 3 x 3 mm
•
Memory density ranging from 4 to 128 Kbytes
DS9111 Rev 4
11/112
52
Functional overview
3
STM8L052R8
Functional overview
Figure 1. High density value line STM8L05xxx device block diagram
OSC_IN,
OSC_OUT
16 MHz internal RC
OSC32_IN,
OSC32_OUT
@VDD
1-16 MHz oscillator
32 kHz oscillator
VDD18
Clock
controller
and CSS
Clocks
to core and
peripherals
38 kHz internal RC
Interrupt controller
16-bit Timer 2
2 channels
16-bit Timer 3
8-bit Timer 4
2 channels
IR_TIM
16-bit Timer 5
Infrared interface
DMA1 (4 channels)
SCL, SDA,
SMB
SPI1_MOSI, SPI1_MISO,
SPI1_SCK, SPI1_NSS
SPI2_MOSI, SPI2_MISO,
SPI2_SCK, SPI2_NSS
USART1_RX, USART1_TX,
USART1_CK
USART2_RX, USART2_TX,
USART2_CK
USART3_RX, USART3_TX,
USART3_CK
V
DDA,
V
SSA
ADC1_INx
V
REF+
V
REF-
VREFINT out
I²C1
SPI1
SPI2
USART1
PVD
A d d r ess , co n t r ol an d d at a b u ses
16-bit Timer 1
2 channels
up to
4-Kbyte RAM
Port A
PA[7:0]
Port B
PB[7:0]
Port C
PC[7:0]
Port D
PD[7:0]
Port E
PE[7:0]
Port F
PF[7:0]
USART3
12-bit ADC1
Port G
PG[7:0]
Beeper
BEEP
RTC
ALARM, CALIB,
TAMP1/2/3
IWDG
(38 kHz clock)
Internal reference
voltage
WWDG
LCD driver
8x24 or 4x28
V
= 2.5 to 3.6 V
LCD
PVD_IN
up to
64-Kbyte
Program memory
256 bytes
Data EEPROM
USART2
@V
/V
DDA SSA
NRST
BOR
Debug module
(SWIM)
3 channels
RESET
V DD=1.8 V
to 3.6 V
V SS
POR/PDR
STM8 Core
SWIM
Power
VOLT. REG.
SEGx, COMx
LCD booster
MS30323V1
1. Legend:
ADC: Analog-to-digital converter
BOR: Brownout reset
DMA: Direct memory access
I²C: Inter-integrated circuit multimaster interface
LCD: Liquid crystal display
POR/PDR: Power on reset / power down reset
RTC: Real-time clock
SPI: Serial peripheral interface
SWIM: Single wire interface module
USART: Universal synchronous asynchronous receiver transmitter
WWDG: Window watchdog
IWDG: independent watchdog
12/112
DS9111 Rev 4
STM8L052R8
3.1
Functional overview
Low power modes
The high density value line STM8L05xxx devices support five low power modes to achieve
the best compromise between low power consumption, short startup time and available
wakeup sources:
•
Wait mode: The CPU clock is stopped, but selected peripherals keep running. An
internal or external interrupt, event or a Reset can be used to exit the microcontroller
from Wait mode (WFE or WFI mode).
•
Low power run mode: The CPU and the selected peripherals are running. Execution
is done from RAM with a low speed oscillator (LSI or LSE). Flash memory and data
EEPROM are stopped and the voltage regulator is configured in ultra low power mode.
The microcontroller enters Low power run mode by software and can exit from this
mode by software or by a reset.
All interrupts must be masked. They cannot be used to exit the microcontroller from this
mode.
•
Low power wait mode: This mode is entered when executing a Wait for event in Low
power run mode. It is similar to Low power run mode except that the CPU clock is
stopped. The wakeup from this mode is triggered by a Reset or by an internal or
external event (peripheral event generated by the timers, serial interfaces, DMA
controller (DMA1) and I/O ports). When the wakeup is triggered by an event, the
system goes back to Low power run mode.
All interrupts must be masked. They cannot be used to exit the microcontroller from this
mode.
•
Active-halt mode: CPU and peripheral clocks are stopped, except RTC. The wakeup
can be triggered by RTC interrupts, external interrupts or reset.
•
Halt mode: CPU and peripheral clocks are stopped, the device remains powered on.
The wakeup is triggered by an external interrupt or reset. A few peripherals have also a
wakeup from Halt capability. Switching off the internal reference voltage reduces power
consumption. Through software configuration it is also possible to wake up the device
without waiting for the internal reference voltage wakeup time to have a fast wakeup
time of 5 µs.
DS9111 Rev 4
13/112
52
Functional overview
STM8L052R8
3.2
Central processing unit STM8
3.2.1
Advanced STM8 Core
The 8-bit STM8 core is designed for code efficiency and performance with an Harvard
architecture and a 3-stage pipeline.
It contains 6 internal registers which are directly addressable in each execution context, 20
addressing modes including indexed indirect and relative addressing, and 80 instructions.
Architecture and registers
•
Harvard architecture
•
3-stage pipeline
•
32-bit wide program memory bus - single cycle fetching most instructions
•
X and Y 16-bit index registers - enabling indexed addressing modes with or without
offset and read-modify-write type data manipulations
•
8-bit accumulator
•
24-bit program counter - 16-Mbyte linear memory space
•
16-bit stack pointer - access to a 64-Kbyte level stack
•
8-bit condition code register - 7 condition flags for the result of the last instruction
Addressing
•
20 addressing modes
•
Indexed indirect addressing mode for lookup tables located anywhere in the address
space
•
Stack pointer relative addressing mode for local variables and parameter passing
Instruction set
3.2.2
•
80 instructions with 2-byte average instruction size
•
Standard data movement and logic/arithmetic functions
•
8-bit by 8-bit multiplication
•
16-bit by 8-bit and 16-bit by 16-bit division
•
Bit manipulation
•
Data transfer between stack and accumulator (push/pop) with direct stack access
•
Data transfer using the X and Y registers or direct memory-to-memory transfers
Interrupt controller
The high density value line STM8L05xxx devices feature a nested vectored interrupt
controller:
14/112
•
Nested interrupts with 3 software priority levels
•
32 interrupt vectors with hardware priority
•
Up to 40 external interrupt sources on 11 vectors
•
Trap and reset interrupts
DS9111 Rev 4
STM8L052R8
Functional overview
3.3
Reset and supply management
3.3.1
Power supply scheme
The device requires a 1.8 V to 3.6 V operating supply voltage (VDD). The external power
supply pins must be connected as follows:
•
VSS1, VDD1, VSS2, VDD2, VSS3, VDD3 = 1.8 to 3.6 V: external power supply for I/Os and
for the internal regulator. Provided externally through VDD pins, the corresponding
ground pin is VSS. VSS1/VSS2/VSS3/VSS4 and VDD1/VDD2/VDD3 must not be left
unconnected.
•
•
3.3.2
VSSA ; VDDA = 1.8 to 3.6 V: external power supplies for analog peripherals. VDDA and
VSSA must be connected to VDD and VSS, respectively.
VREF+ ; VREF- (for ADC1): external reference voltage for ADC1. Must be provided
externally through VREF+ and VREF- pin.
Power supply supervisor
The device has an integrated ZEROPOWER power-on reset (POR)/power-down reset
(PDR), coupled with a brownout reset (BOR) circuitry that ensures proper operation starting
from 1.8 V. After the 1.8 V BOR threshold is reached, the option byte loading process starts,
either to confirm or modify default thresholds, or to disable BOR permanently.
Five BOR thresholds are available through option bytes, starting from 1.8 V to 3 V. To
reduce the power consumption in Halt mode, it is possible to automatically switch off the
internal reference voltage (and consequently the BOR) in Halt mode. The device remains
under reset when VDD is below a specified threshold, VPOR/PDR or VBOR, without the need
for any external reset circuit.
The device features an embedded programmable voltage detector (PVD) that monitors the
VDD/VDDA power supply and compares it to the VPVD threshold. This PVD offers 7 different
levels between 1.85 V and 3.05 V, chosen by software, with a step around 200 mV. An
interrupt can be generated when VDD/VDDA drops below the VPVD threshold and/or when
VDD/VDDA is higher than the VPVD threshold. The interrupt service routine can then generate
a warning message and/or put the MCU into a safe state. The PVD is enabled by software.
3.3.3
Voltage regulator
The high density value line STM8L05xxx embeds an internal voltage regulator for
generating the 1.8 V power supply for the core and peripherals.
This regulator has two different modes:
•
Main voltage regulator mode (MVR) for Run, Wait for interrupt (WFI) and Wait for event
(WFE) modes
•
Low power voltage regulator mode (LPVR) for Halt, Active-halt, Low power run and
Low power wait modes
When entering Halt or Active-halt modes, the system automatically switches from the MVR
to the LPVR in order to reduce current consumption.
DS9111 Rev 4
15/112
52
Functional overview
3.4
STM8L052R8
Clock management
The clock controller distributes the system clock (SYSCLK) coming from different oscillators
to the core and the peripherals. It also manages clock gating for low power modes and
ensures clock robustness.
Features
16/112
•
Clock prescaler: To get the best compromise between speed and current
consumption the clock frequency to the CPU and peripherals can be adjusted by a
programmable prescaler.
•
Safe clock switching: Clock sources can be changed safely on the fly in run mode
through a configuration register.
•
Clock management: To reduce power consumption, the clock controller can stop the
clock to the core, individual peripherals or memory.
•
System clock sources: 4 different clock sources can be used to drive the system
clock:
–
1-16 MHz High speed external crystal (HSE)
–
16 MHz High speed internal RC oscillator (HSI)
–
32.768 kHz Low speed external crystal (LSE)
–
38 kHz Low speed internal RC (LSI)
•
RTC and LCD clock sources: The above four sources can be chosen to clock the
RTC and the LCD, whatever the system clock.
•
Startup clock: After reset, the microcontroller restarts by default with an internal
2 MHz clock (HSI/8). The prescaler ratio and clock source can be changed by the
application program as soon as the code execution starts.
•
Clock security system (CSS): This feature can be enabled by software. If a HSE
clock failure occurs, the system clock is automatically switched to HSI.
•
Configurable main clock output (CCO): This outputs an external clock for use by the
application.
DS9111 Rev 4
STM8L052R8
Functional overview
Figure 2. High density value line STM8L05xxx clock tree diagram
CSS
OSC_OUT
OSC_IN
HSE
HSE OSC
1-16 MHz
SYSCLK to core and
HSI
HSI RC
16 MHz
memory
SYSCLK
Prescaler
/1;2;4;8;16;32;64;128
LSI
LSE
Peripheral
Clock enable (20 bits)
LSE
CLKBEEPSEL[1:0]
LSI
LSI RC
38 k Hz
BEEPCLK
to BEEP
IWDGCLK
to IWDG
RTCCLK
RTCSEL[3:0]
OSC32_OUT
OSC32_IN
RTCCLK
CSS_LSE
RTCCLK/2
/2
CCO
HSI
LSI
HSE
LSE
CCO
prescaler
/1;2;4;8;16;32;64
to LCD
Halt
LCDCLK
configurable
clock output
to RTC
LCD peripheral
c lock enable (1 bit)
RTC
prescaler
/1;2;4;8;16;32;64
LSE OSC
32 .768 kHz
PCLK
to peripherals
SYSCLK
to LCD
LCD peripheral
clock enable (1 bit)
MS30324V1
1. The HSE clock source can be either an external crystal/ceramic resonator or an external source (HSE
bypass). Refer to Section HSE clock in the STM8L15x and STM8L16x reference manual (RM0031).
2. The LSE clock source can be either an external crystal/ceramic resonator or a external source (LSE
bypass). Refer to Section LSE clock in the STM8L15x and STM8L16x reference manual (RM0031).
3.5
Low power real-time clock
The real-time clock (RTC) is an independent binary coded decimal (BCD) timer/counter.
Six byte locations contain the second, minute, hour (12/24 hour), week day, date, month,
year, in BCD (binary coded decimal) format. Correction for 28, 29 (leap year), 30, and 31
day months are made automatically.The subsecond field can also be read in binary format.
The calendar can be corrected from 1 to 32767 RTC clock pulses. This allows to make a
synchronization to a master clock.
The RTC offers a digital calibration which allows an accuracy of +/-0.5ppm.
It provides a programmable alarm and programmable periodic interrupts with wakeup from
Halt capability.
•
Periodic wakeup time using the 32.768 kHz LSE with the lowest resolution (of 61 µs) is
from min. 122 µs to max. 3.9 s. With a different resolution, the wakeup time can reach
36 hours.
•
Periodic alarms based on the calendar can also be generated from every second to
every year.
A clock security system detects a failure on LSE, and can provide an interrupt with wakeup
capability. The RTC clock can automatically switch to LSI in case of LSE failure.
The RTC also provides 3 anti-tamper detection pins. This detection embeds a
programmable filter and can wakeup the MCU.
DS9111 Rev 4
17/112
52
Functional overview
3.6
STM8L052R8
LCD (Liquid crystal display)
The LCD is only available on STM8L052xx devices.
The liquid crystal display drives up to 8 common terminals and up to 24 segment terminals
to drive up to 192 pixels. It can also be configured to drive up to 4 common and 28
segments (up to 112 pixels).
•
Internal step-up converter to guarantee contrast control whatever VDD.
•
Static 1/2, 1/3, 1/4, 1/8 duty supported.
•
Static 1/2, 1/3, 1/4 bias supported.
•
Phase inversion to reduce power consumption and EMI.
•
Up to 8 pixels which can be programmed to blink.
•
The LCD controller can operate in Halt mode.
Note:
Unnecessary segments and common pins can be used as general I/O pins.
3.7
Memories
The high density value line STM8L05xxx devices have the following main features:
•
4 Kbytes of RAM
•
The non-volatile memory is divided into three arrays:
–
64 Kbytes of high density embedded Flash program memory
–
256 bytes of data EEPROM
–
Option bytes
The EEPROM embeds the error correction code (ECC) feature. It supports the read-whilewrite (RWW): it is possible to execute the code from the program matrix while
programming/erasing the data matrix.
The option byte protects part of the Flash program memory from write and readout piracy.
3.8
DMA
A 4-channel direct memory access controller (DMA1) offers a memory-to-memory and
peripherals-from/to-memory transfer capability. The 4 channels are shared between the
following IPs with DMA capability: ADC1, I2C1, SPI1, SPI 2, USART1, USART2, USART3
and the five timers.
18/112
DS9111 Rev 4
STM8L052R8
3.9
Functional overview
Analog-to-digital converter
•
12-bit analog-to-digital converter (ADC1) with 27 channels (including 4 fast channels)
and internal reference voltage
•
Conversion time down to 1 µs with fSYSCLK= 16 MHz
•
Programmable resolution
•
Programmable sampling time
•
Single and continuous mode of conversion
•
Scan capability: automatic conversion performed on a selected group of analog inputs
•
Analog watchdog: interrupt generation when the converted voltage is outside the
programmed threshold
•
Triggered by timer
Note:
ADC1 can be served by DMA1.
3.10
System configuration controller and routing interface
The system configuration controller provides the capability to remap some alternate
functions on different I/O ports. TIM4 and ADC1 DMA channels can also be remapped.
The highly flexible routing interface allows application software to control the routing of
different I/Os to the TIM1 timer input captures. It also controls the routing of internal analog
signals to ADC1 and the internal reference voltage VREFINT.
3.11
Timers
The high density value line STM8L05xxx devices contain one advanced control timer
(TIM1), three 16-bit general purpose timers (TIM2, TIM3 and TIM5) and one 8-bit basic
timer (TIM4).
All the timers can be served by DMA1.
Table 2 compares the features of the advanced control, general-purpose and basic timers.
Table 2. Timer feature comparison
Timer
Counter Counter
resolution
type
DMA1
request
generation
Any integer
from 1 to 65536
TIM1
TIM2
Prescaler factor
16-bit
up/down
TIM3
Any power of 2
from 1 to 128
Yes
Capture/compare
channels
Complementary
outputs
3+1
3
2
None
TIM5
TIM4
8-bit
up
Any power of 2
from 1 to 32768
DS9111 Rev 4
0
19/112
52
Functional overview
3.11.1
STM8L052R8
TIM1 - 16-bit advanced control timer
This is a high-end timer designed for a wide range of control applications. With its
complementary outputs, dead-time control and center-aligned PWM capability, the field of
applications is extended to motor control, lighting and half-bridge driver.
3.11.2
3.11.3
•
16-bit up, down and up/down autoreload counter with 16-bit prescaler
•
3 independent capture/compare channels (CAPCOM) configurable as input capture,
output compare, PWM generation (edge and center aligned mode) and single pulse
mode output
•
1 additional capture/compare channel which is not connected to an external I/O
•
Synchronization module to control the timer with external signals
•
Break input to force timer outputs into a defined state
•
3 complementary outputs with adjustable dead time
•
Encoder mode
•
Interrupt capability on various events (capture, compare, overflow, break, trigger)
16-bit general purpose timers
•
16-bit autoreload (AR) up/down-counter
•
7-bit prescaler adjustable to fixed power of 2 ratios (1…128)
•
2 individually configurable capture/compare channels
•
PWM mode
•
Interrupt capability on various events (capture, compare, overflow, break, trigger)
•
Synchronization with other timers or external signals (external clock, reset, trigger and
enable)
8-bit basic timer
The 8-bit timer consists of an 8-bit up auto-reload counter driven by a programmable
prescaler. It can be used for timebase generation with interrupt generation on timer
overflow.
3.12
Watchdog timers
The watchdog system is based on two independent timers providing maximum security to
the applications.
3.12.1
Window watchdog timer
The window watchdog (WWDG) is used to detect the occurrence of a software fault, usually
generated by external interferences or by unexpected logical conditions, which cause the
application program to abandon its normal sequence.
3.12.2
Independent watchdog timer
The independent watchdog peripheral (IWDG) can be used to resolve processor
malfunctions due to hardware or software failures.
20/112
DS9111 Rev 4
STM8L052R8
Functional overview
It is clocked by the internal LSI RC clock source, and thus stays active even in case of a
CPU clock failure.
3.13
Beeper
The beeper function outputs a signal on the BEEP pin for sound generation. The signal is in
the range of 1, 2 or 4 kHz.
3.14
Communication interfaces
3.14.1
SPI
The serial peripheral interfaces (SPI1 and SPI2) provide half/ full duplex synchronous serial
communication with external devices.
•
Maximum speed: 8 Mbit/s (fSYSCLK/2) both for master and slave
•
Full duplex synchronous transfers
•
Simplex synchronous transfers on 2 lines with a possible bidirectional data line
•
Master or slave operation - selectable by hardware or software
•
Hardware CRC calculation
•
Slave/master selection input pin
Note:
SPI1 and SPI2 can be served by the DMA1 Controller.
3.14.2
I²C
The I2C bus interface (I2C1) provides multi-master capability, and controls all I²C busspecific sequencing, protocol, arbitration and timing.
•
Master, slave and multi-master capability
•
Standard mode up to 100 kHz and fast speed modes up to 400 kHz
•
7-bit and 10-bit addressing modes
•
SMBus 2.0 and PMBus support
•
Hardware CRC calculation
Note:
I2C1 can be served by the DMA1 Controller.
3.14.3
USART
The USART interfaces (USART1, USART2 and USART3) allow full duplex, asynchronous
communications with external devices requiring an industry standard NRZ asynchronous
serial data format. It offers a very wide range of baud rates.
•
1 Mbit/s full duplex SCI
•
SPI1 emulation
•
High precision baud rate generator
•
Smartcard emulation
•
IrDA SIR encoder decoder
•
Single wire half duplex mode
Note:
USART1, USART2 and USART3 can be served by the DMA1 Controller.
DS9111 Rev 4
21/112
52
Functional overview
3.15
STM8L052R8
Infrared (IR) interface
The high density value line STM8L05xxx devices contain an infrared interface which can be
used with an IR LED for remote control functions. Two timer output compare channels are
used to generate the infrared remote control signals.
3.16
Development support
Development tools
Development tools for the STM8 microcontrollers include:
•
The STice emulation system offering tracing and code profiling
•
The STVD high-level language debugger including C compiler, assembler and
integrated development environment
•
The STVP Flash programming software
The STM8 also comes with starter kits, evaluation boards and low-cost in-circuit
debugging/programming tools.
Single wire data interface (SWIM) and debug module
The debug module with its single wire data interface (SWIM) permits non-intrusive real-time
in-circuit debugging and fast memory programming.
The Single wire interface is used for direct access to the debugging module and memory
programming. The interface can be activated in all device operation modes.
The non-intrusive debugging module features a performance close to a full-featured
emulator. Beside memory and peripherals, CPU operation can also be monitored in realtime by means of shadow registers.
Bootloader
A bootloader is available to reprogram the Flash memory using the USART1, USART2,
USART3 (USARTs in asynchronous mode), SPI1 or SPI2 interfaces. The reference
document for the bootloader is UM0560: STM8 bootloader user manual.
The bootloader is used to download application software into the device memories,
including RAM, program and data memory, using standard serial interfaces. It is a
complementary solution to programming via the SWIM debugging interface.
22/112
DS9111 Rev 4
STM8L052R8
Pin description
PE7
PE6
PC7
PC6
PC5
PC4
PC3
PC2
VSS2
V DD2
PC1
PC0
PG7
PG6
PG5
PG4
Figure 3. STM8L052R8 64-pin LQFP64 package pinout
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
PA0
NRST/PA1
PA2
PA3
PA4
PA5
PA6
PA7
VSSA/VREFVSS1
VDD1
VDDA
VREF+
PG0
PG1
PG2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PD7
PD6
PD5
PD4
PF7
PF6
PF5
PF4
PF1
PF0
PB7
PB6
PB5
PB4
PB3
PB2
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
PG3
VLCD
PE0
PE1
PE2
PE3
PE4
PE5
PD0
PD1
PD2
PD3
V DD3
V SS3
PB0
PB1
4
Pin description
ai17835
DS9111 Rev 4
23/112
52
Pin description
STM8L052R8
Table 3. Legend/abbreviation for Table 4
Type
I= input, O = output, S = power supply
Level
FT
Five-volt tolerant
TT
3.6 V tolerant
Output
HS = high sink/source (20 mA)
Port and control Input
configuration
Output
Reset state
float = floating, wpu = weak pull-up
T = true open drain, OD = open drain, PP = push pull
Bold X (pin state after reset release).
Unless otherwise specified, the pin state is the same during the reset phase (i.e.
“under reset”) and after internal reset release (i.e. at reset state).
Table 4. High density value line STM8L05xxx pin description
Output
I/O level
floating
wpu
Ext. interrupt
High sink/source
OD
PP
2
NRST/PA1(1)
I/O
-
-
X
-
HS
X
X Reset
3
PA2/OSC_IN/
[USART1_TX](8)/
[SPI1_MISO] (8)
I/O
-
X
X
X
HS
X
HSE oscillator input /
X Port A2 [USART1 transmit] / [SPI1
master in- slave out]
4
PA3/OSC_OUT/[USART1_
RX](8)/[SPI1_MOSI](8)
I/O
-
X
X
X
HS
X
HSE oscillator output /
X Port A3 [USART1 receive]/ [SPI1
master out/slave in]/
5
PA4/TIM2_BKIN/
[TIM2_ETR](8)/
LCD_COM0/ADC1_IN2
I/O FT(2)
X
X
X
HS
X
Timer 2 - break input
X Port A4 /[Timer 2 - trigger]/
LCD COM 0 / ADC1 input 2
6
PA5/TIM3_BKIN/
[TIM3_ETR](8)/
LCD_COM1/ADC1_IN1
I/O
FT(2)
X
X
X
HS
X
Timer 3 - break input
/[Timer 3 - trigger]/
X Port A5
LCD_COM 1 / ADC1 input
1
7
PA6/[ADC1_TRIG]/
LCD_COM2/ADC1_IN0
I/O FT(2)
X
X
X
HS
X
[ADC1 - trigger] /
X Port A6 LCD_COM2 /
ADC1 input 0
8
PA7/LCD_SEG0(2)
/TIM5_CH1
I/O FT(2)
X
X
X
HS
X
X Port A7
LCD segment 0/ TIM5
channel 1
31
PB0(3)/TIM2_CH1/
LCD_SEG10/ADC1_IN18
I/O FT(2)
X
X
X
HS
X
X Port B0
Timer 2 - channel 1 / LCD
segment 10 / ADC1_IN18
LQFP64
Type
Input
Main function
(after reset)
Pin
number
24/112
Pin name
DS9111 Rev 4
Default alternate function
PA1
STM8L052R8
Pin description
Table 4. High density value line STM8L05xxx pin description (continued)
Output
wpu
Ext. interrupt
High sink/source
OD
PP
PB1/TIM3_CH1/
LCD_SEG11/
ADC1_IN17
I/O FT(2)
X
X
X
HS
X
X Port B1
Timer 3 - channel 1 / LCD
segment 11 / ADC1_IN17
33
PB2/ TIM2_CH2/
LCD_SEG12/
ADC1_IN16
I/O FT(2)
X
X
X
HS
X
X Port B2
Timer 2 - channel 2 / LCD
segment 12 / ADC1_IN16
34
PB3/TIM2_ETR/
LCD_SEG13/
ADC1_IN15
I/O FT(2)
X
X
X
HS
X
X Port B3
Timer 2 - trigger / LCD
segment 13 /ADC1_IN15
35
PB4(3)/[SPI1_NSS](8)/
LCD_SEG14/
ADC1_IN14
I/O FT(2) X(3) X(3)
X
HS
X
[SPI1 master/slave select] /
X Port B4 LCD segment 14 /
ADC1_IN14
36
PB5/[SPI1_SCK](8)/
LCD_SEG15/
ADC1_IN13
I/O FT(2)
X
X
X
HS
X
X Port B5
37
PB6/[SPI1_MOSI](8)/
LCD_SEG16/
ADC1_IN12
I/O FT(2)
X
X
X
HS
X
[SPI1 master out/slave in]/
X Port B6 LCD segment 16 /
ADC1_IN12
38
PB7/[SPI1_MISO](8)/
LCD_SEG17/
ADC1_IN11
I/O FT(2)
X
X
X
HS
X
[SPI1 master in- slave out]
X Port B7 /LCD segment 17 /
ADC1_IN11
53
PC0(2)/I2C1_SDA
I/O FT(2)
X
-
X
T(4)
X
(4)
LQFP64
(2)
I/O level
32
Pin name
Type
floating
Input
Main function
(after reset)
Pin
number
(2)
I/O FT
57
PC2/USART1_RX/
LCD_SEG22/ADC1_IN6/
VREFINT
I/O
FT(2)
X
X
X
HS
X
USART1 receive /
LCD segment 22 /
X Port C2
ADC1_IN6 /Internal voltage
reference output
58
PC3/USART1_TX/
LCD_SEG23/
ADC1_IN5
I/O FT(2)
X
X
X
HS
X
USART1 transmit /
X Port C3 LCD segment 23 /
ADC1_IN5
59
PC4/USART1_CK/
I2C1_SMB/CCO/
ADC1_IN4
X
USART1 synchronous
clock / I2C1_SMB /
X Port C4
Configurable clock output /
ADC1_IN4
X
X
T
Port C0 I2C1 data
PC1 /I2C1_SCL
X
-
[SPI1 clock] / LCD segment
15 / ADC1_IN13
54
I/O FT(2)
X
Default alternate function
HS
DS9111 Rev 4
Port C1 I2C1 clock
25/112
52
Pin description
STM8L052R8
Table 4. High density value line STM8L05xxx pin description (continued)
Output
wpu
Ext. interrupt
High sink/source
OD
PP
I/O FT(2)
X
X
X
HS
X
LSE oscillator input / [SPI1
X Port C5 master/slave select] /
[USART1 transmit]
61
PC6/OSC32_OUT/
[SPI1_SCK](8)/
[USART1_RX](8)
I/O FT(2)
X
X
X
HS
X
LSE oscillator output /
X Port C6 [SPI1 clock] / [USART1
receive]
62
PC7/ADC1_IN3
I/O FT(2)
X
X
X
HS
X
X Port C7 ADC1_IN3
25
PD0/TIM3_CH2/
[ADC1_TRIG](8)/
LCD_SEG7/ADC1_IN22/
I/O FT(2)
X
X
X
HS
X
Timer 3 - channel 2 /
X Port D0 [ADC1_Trigger] / LCD
segment 7 / ADC1_IN22
26
PD1/TIM3_ETR/
LCD_COM3/
ADC1_IN21
I/O FT(2)
X
X
X
HS
X
X Port D1
Timer 3 - trigger /
LCD_COM3 / ADC1_IN21
27
PD2/TIM1_CH1
/LCD_SEG8/
ADC1_IN20
I/O FT(2)
X
X
X
HS
X
X Port D2
Timer 1 - channel 1 / LCD
segment 8 / ADC1_IN20
28
PD3/ TIM1_ETR/
LCD_SEG9/ADC1_IN19
I/O FT(2)
X
X
X
HS
X
X Port D3
Timer 1 - trigger / LCD
segment 9 / ADC1_IN19
45
PD4/TIM1_CH2
/LCD_SEG18/
ADC1_IN10
I/O FT(2)
X
X
X
HS
X
X Port D4
Timer 1 - channel 2 / LCD
segment 18 / ADC1_IN10
46
PD5/TIM1_CH3
/LCD_SEG19/
ADC1_IN9
I/O FT(2)
X
X
X
HS
X
X Port D5
Timer 1 - channel 3 / LCD
segment 19 / ADC1_IN9
47
PD6/TIM1_BKIN
/LCD_SEG20/
ADC1_IN8/RTC_CALIB/
/VREFINT
X
Timer 1 - break input / LCD
segment 20 / ADC1_IN8 /
X Port D6
RTC calibration / Internal
voltage reference output
48
PD7/TIM1_CH1N
/LCD_SEG21/
I/O FT(2)
ADC1_IN7/RTC_ALARM/V
REFINT
X
Timer 1 - inverted channel
1/ LCD segment 21 /
X Port D7 ADC1_IN7 / RTC alarm /
Internal voltage reference
output
26/112
I/O level
PC5/OSC32_IN
/[SPI1_NSS](8)/
[USART1_TX](8)
Pin name
Type
60
LQFP64
floating
Input
Main function
(after reset)
Pin
number
(2)
I/O FT
X
X
X
X
X
X
HS
HS
DS9111 Rev 4
Default alternate function
STM8L052R8
Pin description
Table 4. High density value line STM8L05xxx pin description (continued)
Output
wpu
Ext. interrupt
High sink/source
OD
PP
I/O FT(2)
X
X
X
HS
X
X Port G4
50
PG5/SPI2_SCK
I/O FT(2)
X
X
X
HS
X
X Port G5 SPI2 clock
51
PG6/SPI2_MOSI
I/O FT(2)
X
X
X
HS
X
X Port G6
SPI2
master out- slave in
52
PG7/SPI2_MISO
I/O FT(2)
X
X
X
HS
X
X Port G7
SPI2
master in- slave out
19
PE0(2)/LCD_SEG1/TIM5_C
I/O FT(2)
H2/RTC_TAMP1
X
X
X
HS
X
X Port E0
LCD segment 1/Timer 5
channel 2/RTC tamper 1
20
PE1/TIM1_CH2N/
LCD_SEG2/RTC_TAMP2
X
X
X
HS
X
Timer 1 - inverted channel 2
X Port E1 / LCD segment 2/
RTC tamper 2
21
PE2/TIM1_CH3N/
LCD_SEG3/RTC_TAMP3/
[CCO]
I/O FT(2)
X
X
X
HS
X
Timer 1 - inverted channel 3
/ LCD segment 3/
X Port E2
RTC tamper 3 /
[Configurable clock output]
22
PE3/LCD_SEG4
/USART2_RX
I/O FT(2)
X
X
X
HS
X
X Port E3
LCD segment 4
/USART2 receive
23
PE4/LCD_SEG5
/USART2_TX
I/O FT(2)
X
X
X
HS
X
X Port E4
LCD segment 5
/USART2 transmit
24
PE5/LCD_SEG6/
ADC1_IN23/USART2_CK
I/O FT(2)
X
X
X
HS
X
LCD segment 6 /
X Port E5 ADC1_IN23/USART2
synchronous clock
63
PE6/PVD_IN/TIM5_BKIN
I/O FT(2)
X
X
X
HS
X
X Port E6
64
PE7
/TIM5_ETR
I/O FT(2)
X
X
X
HS
X
X Port E7 TIM5 trigger
39
PF0/ADC1_IN24
/[USART3_TX]
I/O
-
X
X
X
HS
X
X Port F0
ADC1_IN24/
[USART3 transmit]
40
PF1/ADC1_IN25/
[USART3_RX]
I/O
-
X
X
X
HS
X
X Port F1
ADC1_IN25/
[USART3 receive]
41
PF4/LCD_SEG36
/LCD_COM4(5)
I/O FT(2)
X
X
X
HS
X
X Port F4
LCD_SEG36/
LCD COM4(5)
I/O level
PG4/SPI2_NSS
Pin name
Type
49
LQFP64
floating
Input
Main function
(after reset)
Pin
number
I/O FT(2)
DS9111 Rev 4
Default alternate function
SPI2
master/slave select
PVD_IN
/TIM5 break input
27/112
52
Pin description
STM8L052R8
Table 4. High density value line STM8L05xxx pin description (continued)
Output
wpu
Ext. interrupt
High sink/source
OD
PP
PF5/LCD_SEG37/
LCD_COM5(5)
I/O FT(2)
X
X
X
HS
X
X Port F5
LCD_SEG37/
LCD COM5(5)
43
PF6/LCD_SEG38/
LCD_COM6(5)
I/O FT(2)
X
X
X
HS
X
X Port F6
LCD_SEG38/
LCD COM6(5)
44
PF7/LCD_SEG39/
LCD_COM7(5)
I/O FT(2)
X
X
X
HS
X
X Port F7
LCD_SEG39/
LCD COM7(5)
18
VLCD
S
-
-
-
-
-
-
-
11
VDD1
S
-
-
-
-
-
-
- Digital power supply
10
VSS1
-
-
-
-
-
-
-
- I/O ground
12
VDDA
S
-
-
-
-
-
-
- Analog supply voltage
13
VREF+
S
-
-
-
-
-
-
-
ADC1 positive voltage reference
14
PG0/USART3_RX/
[TIM2_BKIN]
I/O FT(2)
X
X
X
HS
X
X
Port G0
USART3 receive /
[Timer 2 - break input]
15
PG1/USART3_TX/
[TIM3_BKIN]
I/O FT(2)
X
X
X
HS
X
X
Port G1
USART3 transmit /
[Timer 3 -break input]
16
PG2/USART3_CK
I/O FT(2)
X
X
X
HS
X
X
Port G2
USART 3 synchronous
clock
17
PG3[TIM3_ETR]
I/O FT(2)
X
X
X
HS
X
X
Port G3 [Timer 3 - trigger]
9
VSSA/VREF-
S
-
-
-
-
-
-
-
Analog ground voltage /
ADC1 negative voltage reference
55
VDD2
S
-
-
-
-
-
-
- IOs supply voltage
56
VSS2
S
-
-
-
-
-
-
- IOs ground voltage
1
PA0(6)/[USART1_CK](8)/
SWIM/BEEP/IR_TIM (7)
X
[USART1 synchronous
clock](8) / SWIM input and
X Port A0
output /Beep output
/ Infrared Timer output
29
30
LQFP64
I/O level
42
Pin name
Type
floating
Input
Main function
(after reset)
Pin
number
HS
Default alternate function
LCD booster external capacitor
I/O
-
X
X
X
VDD3
S
-
-
-
-
-
-
- IOs supply voltage
VSS3
S
-
-
-
-
-
-
- IOs ground voltage
1. At power-up, the PA1/NRST pin is a reset input pin with pull-up. To be used as a general purpose pin (PA1), it can be
configured only as output open-drain or push-pull, not as a general purpose input. Refer to Section Configuring NRST/PA1
pin as general purpose output in the STM8L15x and STM8L16x reference manual (RM0031).
28/112
DS9111 Rev 4
STM8L052R8
Pin description
2. In the 5 V tolerant I/Os, protection diode to VDD is not implemented.
3. A pull-up is applied to PB0 and PB4 during the reset phase. These two pins are input floating after reset release.
4. In the open-drain output column, ‘T’ defines a true open-drain I/O (P-buffer, weak pull-up and protection diode to VDD are
not implemented).
5. SEG/COM multiplexing available on medium+ and high density devices. SEG signals are available by default (see
reference manual for details).
6. The PA0 pin is in input pull-up during the reset phase and after reset release.
7. High Sink LED driver capability available on PA0.
8. [ ] Alternate function remapping option (if the same alternate function is shown twice, it indicates an exclusive choice not a
duplication of the function).
DS9111 Rev 4
29/112
52
Pin description
4.1
STM8L052R8
System configuration options
As shown in Table 4: High density value line STM8L05xxx pin description, some alternate
functions can be remapped on different I/O ports by programming one of the two remapping
registers described in the “Routing interface (RI) and system configuration controller”
section in the STM8L15x and STM8L16x reference manual (RM0031).
30/112
DS9111 Rev 4
STM8L052R8
Memory and register map
5
Memory and register map
5.1
Memory mapping
The memory map is shown in Figure 4.
Figure 4. Memory map
0x00 0000
(1)
Ram (4 Kbytes)
including
(1)
Stack (513 bytes)
0x00 0FFF
0x00 1000
0x00 5000
0x00 5050
0x00 5070
0x00 509D
0x00 50A0
0x00 50A6
0x00 50B0
0x00 50B2
0x00 50C0
0x00 50D3
0x00 50E0
0x00 50F0
0x00 5140
0x00 5200
0x00 5210
0x00 5230
0x00 5250
0x00 5280
0x00 52B0
0x00 52E0
0x00 52FF
0x00 5300
Data EEPROM
(256 bytes)
0x00 10FF
0x00 1100
Reserved
0x00 47FF
0x00 4800
Option bytes
0x00 48FF
0x00 4900
Reserved
0x00 4FFF
0x00 5000
0x00 57FF
0x00 5800
GPIO and
peripheral registers
Reserved
0x00 5FFF
0x00 6000
Boot ROM
(2 Kbytes)
0x00 67FF
0x00 6800
Reserved
0x00 7EFF
0x00 7F00
0x00 5340
0x00 5380
0x00 53C0
0x00 53E0
0x00 53F0
0x00 5400
CPU/SWIM/Debug/ITC
registers
0x00 7FFF
0x00 8000 Reset and interrupt vectors
0x00 807F
0x00 8080
0x00 FFFF
0x00 5430
0x00 5440
0x00 5444
High density Flash
program memory
(64 Kbytes)
GPIO ports
Flash
DMA1
SYSCFGG
ITC-EXTI
WFE
RST
PWR
CLK
WWDG
IWDG
BEEP
RTC
SPI1
I2C1
USART1
TIM2
TIM3
TIM1
TIM4
IRTIM
TIM5
ADC1
Reserved
SPI2
USART2
USART3
LCD
RI
Reserved
MSv45210V2
1. Table 5 lists the boundary addresses for each memory size. The top of the stack is at the RAM end
address.
Refer to Table 7 for an overview of hardware register mapping, to Table 6 for details on I/O port hardware
registers, and to Table 8 for information on CPU/SWIM/debug module controller registers.
Table 5. Flash and RAM boundary addresses
Memory area
Size
Start address
End address
RAM
4 Kbytes
0x00 0000
0x00 0FFF
Flash program memory
64 Kbytes
0x00 8000
0x01 7FFF
DS9111 Rev 4
31/112
52
Memory and register map
5.2
STM8L052R8
Register map
Table 6. I/O port hardware register map
Register label
Register name
Reset
status
0x00 5000
PA_ODR
Port A data output latch register
0x00
0x00 5001
PA_IDR
Port A input pin value register
0xXX
PA_DDR
Port A data direction register
0x00
0x00 5003
PA_CR1
Port A control register 1
0x01
0x00 5004
PA_CR2
Port A control register 2
0x00
0x00 5005
PB_ODR
Port B data output latch register
0x00
0x00 5006
PB_IDR
Port B input pin value register
0xXX
PB_DDR
Port B data direction register
0x00
0x00 5008
PB_CR1
Port B control register 1
0x00
0x00 5009
PB_CR2
Port B control register 2
0x00
0x00 500A
PC_ODR
Port C data output latch register
0x00
0x00 500B
PC_IDR
Port C input pin value register
0xXX
PC_DDR
Port C data direction register
0x00
0x00 500D
PC_CR1
Port C control register 1
0x00
0x00 500E
PC_CR2
Port C control register 2
0x00
0x00 500F
PD_ODR
Port D data output latch register
0x00
0x00 5010
PD_IDR
Port D input pin value register
0xXX
PD_DDR
Port D data direction register
0x00
0x00 5012
PD_CR1
Port D control register 1
0x00
0x00 5013
PD_CR2
Port D control register 2
0x00
0x00 5014
PE_ODR
Port E data output latch register
0x00
0x00 5015
PE_IDR
Port E input pin value register
0xXX
PE_DDR
Port E data direction register
0x00
0x00 5017
PE_CR1
Port E control register 1
0x00
0x00 5018
PE_CR2
Port E control register 2
0x00
0x00 5019
PF_ODR
Port F data output latch register
0x00
0x00 501A
PF_IDR
Port F input pin value register
0xXX
PF_DDR
Port F data direction register
0x00
0x00 501C
PF_CR1
Port F control register 1
0x00
0x00 501D
PF_CR2
Port F control register 2
0x00
Address
0x00 5002
0x00 5007
0x00 500C
0x00 5011
0x00 5016
0x00 501B
32/112
Block
Port A
Port B
Port C
Port D
Port E
Port F
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 6. I/O port hardware register map (continued)
Register label
Register name
Reset
status
0x00 501E
PG_ODR
Port F data output latch register
0x00
0x00 501F
PG_IDR
Port G input pin value register
0xXX
PG_DDR
Port G data direction register
0x00
0x00 5021
PG_CR1
Port G control register 1
0x00
0x00 5022
PG_CR2
Port G control register 2
0x00
Address
0x00 5020
Block
Port G
0x00 5023 to
0x00 502C
Reserved area (10 bytes)
Table 7. General hardware register map
Address
Block
Register label
0x00 502E to
0x00 5049
Register name
Reset
status
Reserved area (27 bytes)
0x00 5050
FLASH_CR1
Flash control register 1
0x00
0x00 5051
FLASH_CR2
Flash control register 2
0x00
FLASH _PUKR
Flash program memory unprotection key
register
0x00
0x00 5053
FLASH _DUKR
Data EEPROM unprotection key register
0x00
0x00 5054
FLASH _IAPSR
Flash in-application programming status
register
0x00
0x00 5052
0x00 5055 to
0x00 506F
Flash
Reserved area (27 bytes)
DS9111 Rev 4
33/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 5070
DMA1_GCSR
DMA1 global configuration & status
register
0xFC
0x00 5071
DMA1_GIR1
DMA1 global interrupt register 1
0x00
Address
Block
0x00 5072 to
0x00 5074
Reserved area (3 bytes)
0x00 5075
DMA1_C0CR
DMA1 channel 0 configuration register
0x00
0x00 5076
DMA1_C0SPR
DMA1 channel 0 status & priority register
0x00
0x00 5077
DMA1_C0NDTR
DMA1 number of data to transfer register
(channel 0)
0x00
0x00 5078
DMA1_C0PARH
DMA1 peripheral address high register
(channel 0)
0x52
0x00 5079
DMA1_C0PARL
DMA1 peripheral address low register
(channel 0)
0x00
0x00 507A
Reserved area (1 byte)
DMA1
0x00 507B
DMA1_C0M0ARH
DMA1 memory 0 address high register
(channel 0)
0x00
0x00 507C
DMA1_C0M0ARL
DMA1 memory 0 address low register
(channel 0)
0x00
0x00 507D
0x00 507E
Reserved area (2 bytes)
0x00 507F
DMA1_C1CR
DMA1 channel 1 configuration register
0x00
0x00 5080
DMA1_C1SPR
DMA1 channel 1 status & priority register
0x00
0x00 5081
DMA1_C1NDTR
DMA1 number of data to transfer register
(channel 1)
0x00
0x00 5082
DMA1_C1PARH
DMA1 peripheral address high register
(channel 1)
0x52
0x00 5083
DMA1_C1PARL
DMA1 peripheral address low register
(channel 1)
0x00
34/112
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 7. General hardware register map (continued)
Address
Block
Register label
0x00 5084
Register name
Reset
status
Reserved area (1 byte)
0x00 5085
DMA1_C1M0ARH
DMA1 memory 0 address high register
(channel 1)
0x00
0x00 5086
DMA1_C1M0ARL
DMA1 memory 0 address low register
(channel 1)
0x00
0x00 5087
0x00 5088
Reserved area (2 bytes)
0x00 5089
DMA1_C2CR
DMA1 channel 2 configuration register
0x00
0x00 508A
DMA1_C2SPR
DMA1 channel 2 status & priority register
0x00
0x00 508B
DMA1_C2NDTR
DMA1 number of data to transfer register
(channel 2)
0x00
0x00 508C
DMA1_C2PARH
DMA1 peripheral address high register
(channel 2)
0x52
0x00 508D
DMA1_C2PARL
DMA1 peripheral address low register
(channel 2)
0x00
0x00 508E
Reserved area (1 byte)
0x00 508F
0x00 5090
DMA1
DMA1_C2M0ARH
DMA1 memory 0 address high register
(channel 2)
0x00
DMA1_C2M0ARL
DMA1 memory 0 address low register
(channel 2)
0x00
0x00 5091
0x00 5092
Reserved area (2 bytes)
0x00 5093
DMA1_C3CR
DMA1 channel 3 configuration register
0x00
0x00 5094
DMA1_C3SPR
DMA1 channel 3 status & priority register
0x00
0x00 5095
DMA1_C3NDTR
DMA1 number of data to transfer register
(channel 3)
0x00
0x00 5096
DMA1_C3PARH_
C3M1ARH
DMA1 peripheral address high register
(channel 3)
0x40
0x00 5097
DMA1_C3PARL_
C3M1ARL
DMA1 peripheral address low register
(channel 3)
0x00
0x00 5098
Reserved area (1 byte)
0x00 5099
DMA1_C3M0ARH
DMA1 memory 0 address high register
(channel 3)
0x00
0x00 509A
DMA1_C3M0ARL
DMA1 memory 0 address low register
(channel 3)
0x00
0x00 509B to
0x00 509C
Reserved area (2 bytes)
DS9111 Rev 4
35/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
SYSCFG_RMPCR3
Remapping register 3
0x00
SYSCFG_RMPCR1
Remapping register 1
0x00
0x00 509F
SYSCFG_RMPCR2
Remapping register 2
0x00
0x00 50A0
EXTI_CR1
External interrupt control register 1
0x00
0x00 50A1
EXTI_CR2
External interrupt control register 2
0x00
EXTI_CR3
External interrupt control register 3
0x00
EXTI_SR1
External interrupt status register 1
0x00
0x00 50A4
EXTI_SR2
External interrupt status register 2
0x00
0x00 50A5
EXTI_CONF1
External interrupt port select register 1
0x00
0x00 50A6
WFE_CR1
WFE control register 1
0x00
WFE_CR2
WFE control register 2
0x00
WFE_CR3
WFE control register 3
0x00
WFE_CR4
WFE control register 4
0x00
EXTI_CR4
External interrupt control register 4
0x00
EXTI_CONF2
External interrupt port select register 2
0x00
Address
Block
0x00 509D
0x00 509E
0x00 50A2
0x00 50A3
0x00 50A7
0x00 50A8
SYSCFG
SYSCFG
ITC - EXTI
WFE
0x00 50A9
0x00 50AA
0x00 50AB
ITC - EXTI
0x00 50A9 to
0x00 50AF
0x00 50B0
0x00 50B1
0x00 50B2
0x00 50B3
0x00 50B4 to
0x00 50BF
36/112
Reserved area (7 bytes)
RST
PWR
RST_CR
Reset control register
0x00
RST_SR
Reset status register
0x01
PWR_CSR1
Power control and status register 1
0x00
PWR_CSR2
Power control and status register 2
0x00
Reserved area (12 bytes)
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 50C0
CLK_CKDIVR
Clock master divider register
0x03
0x00 50C1
CLK_CRTCR
Clock RTC register
0x00(1)
0x00 50C2
CLK_ICKR
Internal clock control register
0x11
0x00 50C3
CLK_PCKENR1
Peripheral clock gating register 1
0x00
0x00 50C4
CLK_PCKENR2
Peripheral clock gating register 2
0x00
0x00 50C5
CLK_CCOR
Configurable clock control register
0x00
0x00 50C6
CLK_ECKR
External clock control register
0x00
0x00 50C7
CLK_SCSR
System clock status register
0x01
CLK_SWR
System clock switch register
0x01
0x00 50C9
CLK_SWCR
Clock switch control register
0xX0
0x00 50CA
CLK_CSSR
Clock security system register
0x00
0x00 50CB
CLK_CBEEPR
Clock BEEP register
0x00
0x00 50CC
CLK_HSICALR
HSI calibration register
0xXX
0x00 50CD
CLK_HSITRIMR
HSI clock calibration trimming register
0x00
0x00 50CE
CLK_HSIUNLCKR
HSI unlock register
0x00
0x00 50CF
CLK_REGCSR
Main regulator control status register
0bxx11100x
0x00 50D0
CLK_PCKENR3
Peripheral clock gating register 3
0x00
Address
0x00 50C8
Block
CLK
0x00 50D1 to
0x00 50D2
0x00 50D3
0x00 50D4
Reserved area (2 bytes)
WWDG
WWDG_CR
WWDG control register
0x7F
WWDG_WR
WWDR window register
0x7F
0x00 50D5 to
00 50DF
Reserved area (11 bytes)
0x00 50E0
0x00 50E1
IWDG
0x00 50E2
IWDG_KR
IWDG key register
0xXX
IWDG_PR
IWDG prescaler register
0x00
IWDG_RLR
IWDG reload register
0xFF
0x00 50E3 to
0x00 50EF
Reserved area (13 bytes)
0x00 50F0
0x00 50F1
0x00 50F2
0x00 50F3
0x00 50F4 to
0x00 513F
BEEP_CSR1
BEEP
BEEP control/status register 1
0x00
Reserved area (2 bytes)
BEEP_CSR2
BEEP control/status register 2
0x1F
Reserved area (76 bytes)
DS9111 Rev 4
37/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 5140
RTC_TR1
Time register 1
0x00
0x00 5141
RTC_TR2
Time register 2
0x00
0x00 5142
RTC_TR3
Time register 3
0x00
Address
Block
0x00 5143
Reserved area (1 byte)
0x00 5144
RTC_DR1
Date register 1
0x01
0x00 5145
RTC_DR2
Date register 2
0x21
0x00 5146
RTC_DR3
Date register 3
0x00
0x00 5147
Reserved area (1 byte)
0x00 5148
RTC_CR1
Control register 1
0x00(1)
0x00 5149
RTC_CR2
Control register 2
0x00(1)
0x00 514A
RTC_CR3
Control register 3
0x00(1)
0x00 514B
Reserved area (1 byte)
0x00 514C
RTC_ISR1
Initialization and status register 1
0x01
0x00 514D
RTC_ISR2
Initialization and Status register 2
0x00
0x00 514E
0x00 514F
0x00 5150
0x00 5151
0x00 5152
Reserved area (2 bytes)
RTC
RTC_SPRERH(1)
Synchronous prescaler register high
0x00(1)
RTC_SPRERL(1)
Synchronous prescaler register low
0xFF(1)
RTC_APRER(1)
Asynchronous prescaler register
0x7F(1)
0x00 5153
Reserved area (1 byte)
0x00 5154
RTC_WUTRH(1)
Wakeup timer register high
0xFF(1)
0x00 5155
RTC_WUTRL(1)
Wakeup timer register low
0xFF(1)
0x00 5156
Reserved area (1 bytes)
0x00 5157
RTC_SSRL
Subsecond register low
0x00
0x00 5158
RTC_SSRH
Subsecond register high
0x00
0x00 5159
RTC_WPR
Write protection register
0x00
0x00 515A
RTC_SHIFTRH
Shift register high
0x00
0x00 515B
RTC_SHIFTRL
Shift register low
0x00
0x00 515C
RTC_ALRMAR1
Alarm A register 1
0x00(1)
0x00 515D
RTC_ALRMAR2
Alarm A register 2
0x00(1)
0x00 515E
RTC_ALRMAR3
Alarm A register 3
0x00(1)
0x00 515F
RTC_ALRMAR4
Alarm A register 4
0x00(1)
0x00 5160 to
0x00 5163
38/112
Reserved area (4 bytes)
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 7. General hardware register map (continued)
Address
Block
0x00 5164
0x00 5165
RTC
0x00 5166
Register label
Register name
Reset
status
RTC_ALRMASSRH
Alarm A subsecond register high
0x00(1)
RTC_ALRMASSRL
Alarm A subsecond register low
0x00(1)
RTC_ALRMASSMS
KR
Alarm A masking register
0x00(1)
0x00 5167 to
0x00 5169
Reserved area (3 bytes)
0x00 516A
0x00 516B
0x00 516C
RTC
0x00 516D
RTC_CALRH
Calibration register high
0x00(1)
RTC_CALRL
Calibration register low
0x00(1)
RTC_TCR1
Tamper control register 1
0x00(1)
RTC_TCR2
Tamper control register 2
0x00(1)
0x00 516E to
0x00 518A
0x00 5190
Reserved area
CSSLSE
CSSLSE_CSR
0x00 519A to
0x00 51FF
CSS on LSE control and status register
0x00(1)
Reserved area
0x00 5200
SPI1_CR1
SPI1 control register 1
0x00
0x00 5201
SPI1_CR2
SPI1 control register 2
0x00
0x00 5202
SPI1_ICR
SPI1 interrupt control register
0x00
SPI1_SR
SPI1 status register
0x02
SPI1_DR
SPI1 data register
0x00
0x00 5205
SPI1_CRCPR
SPI1 CRC polynomial register
0x07
0x00 5206
SPI1_RXCRCR
SPI1 Rx CRC register
0x00
0x00 5207
SPI1_TXCRCR
SPI1 Tx CRC register
0x00
0x00 5203
0x00 5204
0x00 5208 to
0x00 520F
SPI1
Reserved area (8 bytes)
DS9111 Rev 4
39/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 5210
I2C1_CR1
I2C1 control register 1
0x00
0x00 5211
I2C1_CR2
I2C1 control register 2
0x00
0x00 5212
I2C1_FREQR
I2C1 frequency register
0x00
0x00 5213
I2C1_OARL
I2C1 own address register low
0x00
0x00 5214
I2C1_OARH
I2C1 own address register high
0x00
0x00 5215
I2C1_OARH
I2C1 own address register for dual mode
0x00
0x00 5216
I2C1_DR
I2C1 data register
0x00
I2C1_SR1
I2C1 status register 1
0x00
I2C1_SR2
I2C1 status register 2
0x00
0x00 5219
I2C1_SR3
I2C1 status register 3
0x0x
0x00 521A
I2C1_ITR
I2C1 interrupt control register
0x00
0x00 521B
I2C1_CCRL
I2C1 clock control register low
0x00
0x00 521C
I2C1_CCRH
I2C1 clock control register high
0x00
0x00 521D
I2C1_TRISER
I2C1 TRISE register
0x02
0x00 521E
I2C1_PECR
I2C1 packet error checking register
0x00
Address
0x00 5217
0x00 5218
Block
I2C1
0x00 521F to
0x00 522F
Reserved area (17 bytes)
0x00 5230
USART1_SR
USART1 status register
0xC0
0x00 5231
USART1_DR
USART1 data register
0xXX
0x00 5232
USART1_BRR1
USART1 baud rate register 1
0x00
0x00 5233
USART1_BRR2
USART1 baud rate register 2
0x00
0x00 5234
USART1_CR1
USART1 control register 1
0x00
USART1_CR2
USART1 control register 2
0x00
0x00 5236
USART1_CR3
USART1 control register 3
0x00
0x00 5237
USART1_CR4
USART1 control register 4
0x00
0x00 5238
USART1_CR5
USART1 control register 5
0x00
0x00 5239
USART1_GTR
USART1 guard time register
0x00
0x00 523A
USART1_PSCR
USART1 prescaler register
0x00
0x00 5235
0x00 523B to
0x00 524F
40/112
USART1
Reserved area (21 bytes)
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 5250
TIM2_CR1
TIM2 control register 1
0x00
0x00 5251
TIM2_CR2
TIM2 control register 2
0x00
0x00 5252
TIM2_SMCR
TIM2 Slave mode control register
0x00
0x00 5253
TIM2_ETR
TIM2 external trigger register
0x00
0x00 5254
TIM2_DER
TIM2 DMA1 request enable register
0x00
0x00 5255
TIM2_IER
TIM2 interrupt enable register
0x00
0x00 5256
TIM2_SR1
TIM2 status register 1
0x00
0x00 5257
TIM2_SR2
TIM2 status register 2
0x00
0x00 5258
TIM2_EGR
TIM2 event generation register
0x00
0x00 5259
TIM2_CCMR1
TIM2 capture/compare mode register 1
0x00
0x00 525A
TIM2_CCMR2
TIM2 capture/compare mode register 2
0x00
TIM2_CCER1
TIM2 capture/compare enable register 1
0x00
0x00 525C
TIM2_CNTRH
TIM2 counter high
0x00
0x00 525D
TIM2_CNTRL
TIM2 counter low
0x00
0x00 525E
TIM2_PSCR
TIM2 prescaler register
0x00
0x00 525F
TIM2_ARRH
TIM2 auto-reload register high
0xFF
0x00 5260
TIM2_ARRL
TIM2 auto-reload register low
0xFF
0x00 5261
TIM2_CCR1H
TIM2 capture/compare register 1 high
0x00
0x00 5262
TIM2_CCR1L
TIM2 capture/compare register 1 low
0x00
0x00 5263
TIM2_CCR2H
TIM2 capture/compare register 2 high
0x00
0x00 5264
TIM2_CCR2L
TIM2 capture/compare register 2 low
0x00
0x00 5265
TIM2_BKR
TIM2 break register
0x00
0x00 5266
TIM2_OISR
TIM2 output idle state register
0x00
Address
0x00 525B
0x00 5267 to
0x00 527F
Block
TIM2
Reserved area (25 bytes)
DS9111 Rev 4
41/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 5280
TIM3_CR1
TIM3 control register 1
0x00
0x00 5281
TIM3_CR2
TIM3 control register 2
0x00
0x00 5282
TIM3_SMCR
TIM3 Slave mode control register
0x00
0x00 5283
TIM3_ETR
TIM3 external trigger register
0x00
0x00 5284
TIM3_DER
TIM3 DMA1 request enable register
0x00
0x00 5285
TIM3_IER
TIM3 interrupt enable register
0x00
0x00 5286
TIM3_SR1
TIM3 status register 1
0x00
0x00 5287
TIM3_SR2
TIM3 status register 2
0x00
0x00 5288
TIM3_EGR
TIM3 event generation register
0x00
0x00 5289
TIM3_CCMR1
TIM3 Capture/Compare mode register 1
0x00
0x00 528A
TIM3_CCMR2
TIM3 Capture/Compare mode register 2
0x00
TIM3_CCER1
TIM3 Capture/Compare enable register 1
0x00
0x00 528C
TIM3_CNTRH
TIM3 counter high
0x00
0x00 528D
TIM3_CNTRL
TIM3 counter low
0x00
0x00 528E
TIM3_PSCR
TIM3 prescaler register
0x00
0x00 528F
TIM3_ARRH
TIM3 Auto-reload register high
0xFF
0x00 5290
TIM3_ARRL
TIM3 Auto-reload register low
0xFF
0x00 5291
TIM3_CCR1H
TIM3 Capture/Compare register 1 high
0x00
0x00 5292
TIM3_CCR1L
TIM3 Capture/Compare register 1 low
0x00
0x00 5293
TIM3_CCR2H
TIM3 Capture/Compare register 2 high
0x00
0x00 5294
TIM3_CCR2L
TIM3 Capture/Compare register 2 low
0x00
0x00 5295
TIM3_BKR
TIM3 break register
0x00
0x00 5296
TIM3_OISR
TIM3 output idle state register
0x00
Address
0x00 528B
0x00 5297 to
0x00 52AF
42/112
Block
TIM3
Reserved area (25 bytes)
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 52B0
TIM1_CR1
TIM1 control register 1
0x00
0x00 52B1
TIM1_CR2
TIM1 control register 2
0x00
0x00 52B2
TIM1_SMCR
TIM1 Slave mode control register
0x00
0x00 52B3
TIM1_ETR
TIM1 external trigger register
0x00
0x00 52B4
TIM1_DER
TIM1 DMA1 request enable register
0x00
0x00 52B5
TIM1_IER
TIM1 Interrupt enable register
0x00
0x00 52B6
TIM1_SR1
TIM1 status register 1
0x00
0x00 52B7
TIM1_SR2
TIM1 status register 2
0x00
0x00 52B8
TIM1_EGR
TIM1 event generation register
0x00
0x00 52B9
TIM1_CCMR1
TIM1 Capture/Compare mode register 1
0x00
0x00 52BA
TIM1_CCMR2
TIM1 Capture/Compare mode register 2
0x00
0x00 52BB
TIM1_CCMR3
TIM1 Capture/Compare mode register 3
0x00
0x00 52BC
TIM1_CCMR4
TIM1 Capture/Compare mode register 4
0x00
0x00 52BD
TIM1_CCER1
TIM1 Capture/Compare enable register 1
0x00
0x00 52BE
TIM1_CCER2
TIM1 Capture/Compare enable register 2
0x00
0x00 52BF
TIM1_CNTRH
TIM1 counter high
0x00
TIM1_CNTRL
TIM1 counter low
0x00
TIM1_PSCRH
TIM1 prescaler register high
0x00
0x00 52C2
TIM1_PSCRL
TIM1 prescaler register low
0x00
0x00 52C3
TIM1_ARRH
TIM1 Auto-reload register high
0xFF
0x00 52C4
TIM1_ARRL
TIM1 Auto-reload register low
0xFF
0x00 52C5
TIM1_RCR
TIM1 Repetition counter register
0x00
0x00 52C6
TIM1_CCR1H
TIM1 Capture/Compare register 1 high
0x00
0x00 52C7
TIM1_CCR1L
TIM1 Capture/Compare register 1 low
0x00
0x00 52C8
TIM1_CCR2H
TIM1 Capture/Compare register 2 high
0x00
0x00 52C9
TIM1_CCR2L
TIM1 Capture/Compare register 2 low
0x00
0x00 52CA
TIM1_CCR3H
TIM1 Capture/Compare register 3 high
0x00
0x00 52CB
TIM1_CCR3L
TIM1 Capture/Compare register 3 low
0x00
0x00 52CC
TIM1_CCR4H
TIM1 Capture/Compare register 4 high
0x00
0x00 52CD
TIM1_CCR4L
TIM1 Capture/Compare register 4 low
0x00
0x00 52CE
TIM1_BKR
TIM1 break register
0x00
0x00 52CF
TIM1_DTR
TIM1 dead-time register
0x00
0x00 52D0
TIM1_OISR
TIM1 output idle state register
0x00
0x00 52D1
TIM1_DCR1
DMA1 control register 1
0x00
Address
0x00 52C0
0x00 52C1
Block
TIM1
DS9111 Rev 4
43/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Address
0x00 52D2
0x00 52D3
Block
TIM1
Register label
Register name
Reset
status
TIM1_DCR2
TIM1 DMA1 control register 2
0x00
TIM1_DMA1R
TIM1 DMA1 address for burst mode
0x00
0x00 52D4 to
0x00 52DF
Reserved area (12 bytes)
0x00 52E0
TIM4_CR1
TIM4 control register 1
0x00
0x00 52E1
TIM4_CR2
TIM4 control register 2
0x00
0x00 52E2
TIM4_SMCR
TIM4 Slave mode control register
0x00
0x00 52E3
TIM4_DER
TIM4 DMA1 request enable register
0x00
TIM4_IER
TIM4 Interrupt enable register
0x00
TIM4_SR1
TIM4 status register 1
0x00
0x00 52E6
TIM4_EGR
TIM4 Event generation register
0x00
0x00 52E7
TIM4_CNTR
TIM4 counter
0x00
0x00 52E8
TIM4_PSCR
TIM4 prescaler register
0x00
0x00 52E9
TIM4_ARR
TIM4 Auto-reload register
0x00
0x00 52E4
0x00 52E5
TIM4
0x00 52EA to
0x00 52FE
0x00 52FF
Reserved area (21 bytes)
IR_CR
Infrared control register
0x00
0x00 5300
TIM5_CR1
TIM5 control register 1
0x00
0x00 5301
TIM5_CR2
TIM5 control register 2
0x00
0x00 5302
TIM5_SMCR
TIM5 Slave mode control register
0x00
0x00 5303
TIM5_ETR
TIM5 external trigger register
0x00
0x00 5304
TIM5_DER
TIM5 DMA1 request enable register
0x00
0x00 5305
TIM5_IER
TIM5 interrupt enable register
0x00
0x00 5306
TIM5_SR1
TIM5 status register 1
0x00
0x00 5307
TIM5_SR2
TIM5 status register 2
0x00
TIM5_EGR
TIM5 event generation register
0x00
0x00 5309
TIM5_CCMR1
TIM5 Capture/Compare mode register 1
0x00
0x00 530A
TIM5_CCMR2
TIM5 Capture/Compare mode register 2
0x00
0x00 530B
TIM5_CCER1
TIM5 Capture/Compare enable register 1
0x00
0x00 530C
TIM5_CNTRH
TIM5 counter high
0x00
0x00 530D
TIM5_CNTRL
TIM5 counter low
0x00
0x00 530E
TIM5_PSCR
TIM5 prescaler register
0x00
0x00 530F
TIM5_ARRH
TIM5 Auto-reload register high
0xFF
0x00 5310
TIM5_ARRL
TIM5 Auto-reload register low
0xFF
0x00 5308
44/112
IRTIM
TIM5
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 5311
TIM5_CCR1H
TIM5 Capture/Compare register 1 high
0x00
0x00 5312
TIM5_CCR1L
TIM5 Capture/Compare register 1 low
0x00
TIM5_CCR2H
TIM5 Capture/Compare register 2 high
0x00
TIM5_CCR2L
TIM5 Capture/Compare register 2 low
0x00
0x00 5315
TIM5_BKR
TIM5 break register
0x00
0x00 5316
TIM5_OISR
TIM5 output idle state register
0x00
Address
0x00 5313
0x00 5314
Block
TIM5
0x00 5317
to
0x00 533F
Reserved area
0x00 5340
ADC1_CR1
ADC1 configuration register 1
0x00
0x00 5341
ADC1_CR2
ADC1 configuration register 2
0x00
0x00 5342
ADC1_CR3
ADC1 configuration register 3
0x1F
0x00 5343
ADC1_SR
ADC1 status register
0x00
0x00 5344
ADC1_DRH
ADC1 data register high
0x00
0x00 5345
ADC1_DRL
ADC1 data register low
0x00
0x00 5346
ADC1_HTRH
ADC1 high threshold register high
0x0F
0x00 5347
ADC1_HTRL
ADC1 high threshold register low
0xFF
ADC1_LTRH
ADC1 low threshold register high
0x00
ADC1_LTRL
ADC1 low threshold register low
0x00
0x00 534A
ADC1_SQR1
ADC1 channel sequence 1 register
0x00
0x00 534B
ADC1_SQR2
ADC1 channel sequence 2 register
0x00
0x00 534C
ADC1_SQR3
ADC1 channel sequence 3 register
0x00
0x00 534D
ADC1_SQR4
ADC1 channel sequence 4 register
0x00
0x00 534E
ADC1_TRIGR1
ADC1 trigger disable 1
0x00
0x00 534F
ADC1_TRIGR2
ADC1 trigger disable 2
0x00
0x00 5350
ADC1_TRIGR3
ADC1 trigger disable 3
0x00
0x00 5351
ADC1_TRIGR4
ADC1 trigger disable 4
0x00
0x00 5348
0x00 5349
0x00 5352 to
0x00 53BF
ADC1
Reserved area (110 bytes)
DS9111 Rev 4
45/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Register label
Register name
Reset
status
0x00 53C0
SPI2_CR1
SPI2 control register 1
0x00
0x00 53C1
SPI2_CR2
SPI2 control register 2
0x00
0x00 53C2
SPI2_ICR
SPI2 interrupt control register
0x00
SPI2_SR
SPI2 status register
0x02
SPI2_DR
SPI2 data register
0x00
0x00 53C5
SPI2_CRCPR
SPI2 CRC polynomial register
0x07
0x00 53C6
SPI2_RXCRCR
SPI2 Rx CRC register
0x00
0x00 53C7
SPI2_TXCRCR
SPI2 Tx CRC register
0x00
Address
0x00 53C3
0x00 53C4
Block
SPI2
0x00 53C8 to
0x00 53DF
Reserved area
0x00 53E0
USART2_SR
USART2 status register
0xC0
0x00 53E1
USART2_DR
USART2 data register
0xXX
0x00 53E2
USART2_BRR1
USART2 baud rate register 1
0x00
0x00 53E3
USART2_BRR2
USART2 baud rate register 2
0x00
0x00 53E4
USART2_CR1
USART2 control register 1
0x00
USART2_CR2
USART2 control register 2
0x00
0x00 53E6
USART2_CR3
USART2 control register 3
0x00
0x00 53E7
USART2_CR4
USART2 control register 4
0x00
0x00 53E8
USART2_CR5
USART2 control register 5
0x00
0x00 53E9
USART2_GTR
USART2 guard time register
0x00
0x00 53EA
USART2_PSCR
USART2 prescaler register
0x00
0x00 53E5
USART2
0x00 53EB to
0x00 53EF
Reserved area
0x00 53F0
USART3_SR
USART3 status register
0xC0
0x00 53F1
USART3_DR
USART3 data register
0xXX
0x00 53F2
USART3_BRR1
USART3 baud rate register 1
0x00
0x00 53F3
USART3_BRR2
USART3 baud rate register 2
0x00
0x00 53F4
USART3_CR1
USART3 control register 1
0x00
USART3_CR2
USART3 control register 2
0x00
0x00 53F6
USART3_CR3
USART3 control register 3
0x00
0x00 53F7
USART3_CR4
USART3 control register 4
0x00
0x00 53F8
USART3_CR5
USART3 control register 5
0x00
0x00 53F9
USART3_GTR
USART3 guard time register
0x00
0x00 53FA
USART3_PSCR
USART3 prescaler register
0x00
0x00 53F5
46/112
USART3
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 7. General hardware register map (continued)
Address
Block
Register label
0x00 53FB to
0x00 53FF
Register name
Reset
status
Reserved area
0x00 5400
LCD_CR1
LCD control register 1
0x00
0x00 5401
LCD_CR2
LCD control register 2
0x00
0x00 5402
LCD_CR3
LCD control register 3
0x00
LCD_FRQ
LCD frequency selection register
0x00
LCD_PM0
LCD Port mask register 0
0x00
0x00 5405
LCD_PM1
LCD Port mask register 1
0x00
0x00 5406
LCD_PM2
LCD Port mask register 2
0x00
0x00 5403
0x00 5404
LCD
0x00 5407
Reserved area
0x00 5408
LCD_PM4
0x00 5409 to
0x00 540B
LCD Port mask register 4
0x00
Reserved area (3 bytes)
0x00 540C
LCD_RAM0
LCD display memory 0
0x00
0x00 540D
LCD_RAM1
LCD display memory 1
0x00
0x00 540E
LCD_RAM2
LCD display memory 2
0x00
0x00 540F
LCD_RAM3
LCD display memory 3
0x00
0x00 5410
LCD_RAM4
LCD display memory 4
0x00
0x00 5411
LCD_RAM5
LCD display memory 5
0x00
0x00 5412
LCD_RAM6
LCD display memory 6
0x00
0x00 5413
LCD_RAM7
LCD display memory 7
0x00
0x00 5414
LCD_RAM8
LCD display memory 8
0x00
LCD_RAM9
LCD display memory 9
0x00
LCD_RAM10
LCD display memory 10
0x00
0x00 5417
LCD_RAM11
LCD display memory 11
0x00
0x00 5418
LCD_RAM12
LCD display memory 12
0x00
0x00 5419
LCD_RAM13
LCD display memory 13
0x00
0x00 5415
0x00 5416
LCD
0x00 541A
0x00 541B
Reserved area
LCD_RAM15
0x00 541C
0x00 541D
LCD_RAM17
LCD display memory 17
0x00
Reserved area
LCD_RAM19
0x00 5420
0x00 5421
0x00
Reserved area
0x00 541E
0x00 541F
LCD display memory 15
LCD display memory 19
0x00
Reserved area
LCD_RAM21
DS9111 Rev 4
LCD display memory 21
0x00
47/112
52
Memory and register map
STM8L052R8
Table 7. General hardware register map (continued)
Address
Block
Register label
0x00 5422 to
0x00 542E
0x00 542F
Register name
Reset
status
Reserved area
LCD
LCD_CR4
0x00 5430
LCD control register 4
Reserved area (1 byte)
0x00
0x00
0x00 5431
RI_ICR1
Timer input capture routing register 1
0x00
0x00 5432
RI_ICR2
Timer input capture routing register 2
0x00
0x00 5433
RI_IOIR1
I/O input register 1
0xXX
0x00 5434
RI_IOIR2
I/O input register 2
0xXX
0x00 5435
RI_IOIR3
I/O input register 3
0xXX
0x00 5436
RI_IOCMR1
I/O control mode register 1
0x00
RI_IOCMR2
I/O control mode register 2
0x00
RI_IOCMR3
I/O control mode register 3
0x00
0x00 5439
RI_IOSR1
I/O switch register 1
0x00
0x00 543A
RI_IOSR2
I/O switch register 2
0x00
0x00 543B
RI_IOSR3
I/O switch register 3
0x00
0x00 543C
RI_IOGCR
I/O group control register
0x3F
0x00 543D
RI_ASCR1
Analog switch register 1
0x00
0x00 543E
RI_ASCR2
Analog switch register 2
0x00
0x00 543F
RI_RCR
Resistor control register 1
0x00
0x00 5437
0x00 5438
0x00 5440 to
0x00 5444
RI
Reserved area (5 bytes)
1. These registers are not impacted by a system reset. They are reset at power-on.
48/112
DS9111 Rev 4
STM8L052R8
Memory and register map
Table 8. CPU/SWIM/debug module/interrupt controller registers
Register Label
Register Name
Reset
Status
0x00 7F00
A
Accumulator
0x00
0x00 7F01
PCE
Program counter extended
0x00
0x00 7F02
PCH
Program counter high
0x00
0x00 7F03
PCL
Program counter low
0x00
XH
X index register high
0x00
XL
X index register low
0x00
0x00 7F06
YH
Y index register high
0x00
0x00 7F07
YL
Y index register low
0x00
0x00 7F08
SPH
Stack pointer high
0x03
0x00 7F09
SPL
Stack pointer low
0xFF
0x00 7F0A
CCR
Condition code register
0x28
Address
Block
0x00 7F04
0x00 7F05
0x00 7F0B to
0x00 7F5F
CPU(1)
Reserved area (85 bytes)
CPU
0x00 7F60
CFG_GCR
Global configuration register
0x00
0x00 7F70
ITC_SPR1
Interrupt Software priority register 1
0xFF
0x00 7F71
ITC_SPR2
Interrupt Software priority register 2
0xFF
0x00 7F72
ITC_SPR3
Interrupt Software priority register 3
0xFF
ITC_SPR4
Interrupt Software priority register 4
0xFF
ITC_SPR5
Interrupt Software priority register 5
0xFF
0x00 7F75
ITC_SPR6
Interrupt Software priority register 6
0xFF
0x00 7F76
ITC_SPR7
Interrupt Software priority register 7
0xFF
0x00 7F77
ITC_SPR8
Interrupt Software priority register 8
0xFF
0x00 7F73
0x00 7F74
ITC-SPR
0x00 7F78 to
0x00 7F79
0x00 7F80
0x00 7F81 to
0x00 7F8F
Reserved area (2 bytes)
SWIM
SWIM_CSR
SWIM control status register
0x00
Reserved area (15 bytes)
DS9111 Rev 4
49/112
52
Memory and register map
STM8L052R8
Table 8. CPU/SWIM/debug module/interrupt controller registers (continued)
Register Label
Register Name
Reset
Status
0x00 7F90
DM_BK1RE
DM breakpoint 1 register extended byte
0xFF
0x00 7F91
DM_BK1RH
DM breakpoint 1 register high byte
0xFF
0x00 7F92
DM_BK1RL
DM breakpoint 1 register low byte
0xFF
0x00 7F93
DM_BK2RE
DM breakpoint 2 register extended byte
0xFF
0x00 7F94
DM_BK2RH
DM breakpoint 2 register high byte
0xFF
DM_BK2RL
DM breakpoint 2 register low byte
0xFF
0x00 7F96
DM_CR1
DM Debug module control register 1
0x00
0x00 7F97
DM_CR2
DM Debug module control register 2
0x00
0x00 7F98
DM_CSR1
DM Debug module control/status register 1
0x10
0x00 7F99
DM_CSR2
DM Debug module control/status register 2
0x00
0x00 7F9A
DM_ENFCTR
DM enable function register
0xFF
Address
0x00 7F95
Block
DM
0x00 7F9B to
0x00 7F9F
Reserved area (5 bytes)
1. Accessible by debug module only
50/112
DS9111 Rev 4
STM8L052R8
6
Interrupt vector mapping
Interrupt vector mapping
Table 9. Interrupt mapping
IRQ
No.
Source
block
RESET
0
1
2
Description
Reset
Yes
Yes
Yes
0x00 8000
0x00 8004
-
-
-
-
TLI(2)
External Top level Interrupt
-
-
-
-
FLASH
DMA1 0/1
EOP/WR_PG_DIS
DMA1 channels 0/1
DMA1 channels 2/3
4
RTC/LSE_
CSS
5
6
Vector
address
Yes
Software interrupt
DMA1 2/3
-
-
0x00 8008
Yes
Yes
(5)
0x00 800C
Yes
Yes(5)
0x00 8010
(5)
0x00 8014
-
-
Yes
RTC alarm interrupt/LSE
CSS interrupt
Yes
Yes
Yes
Yes
0x00 8018
EXTI E/F/
PVD(3)
PortE/F interrupt/PVD
interrupt
Yes
Yes
Yes
Yes(5)
0x00 801C
EXTIB/G
External interrupt port B/G
Yes
Yes
Yes
Yes(5)
0x00 8020
0x00 8024
7
EXTID/H
8
EXTI0
10
Wakeup
Wakeup
Wakeup
from
from Wait from Wait
Active(WFI
(WFE
halt mode
mode)
mode)(1)
TRAP
3
9
Wakeup
from Halt
mode
EXTI1
EXTI2
Yes
External interrupt port D
Yes
Yes
Yes
Yes(5)
External interrupt 0
Yes
Yes
Yes
Yes(5)
0x00 8028
Yes
Yes
(5)
0x00 802C
Yes
Yes(5)
0x00 8030
(5)
0x00 8034
External interrupt 1
External interrupt 2
Yes
Yes
Yes
Yes
11
EXTI3
External interrupt 3
Yes
Yes
Yes
Yes
12
EXTI4
External interrupt 4
Yes
Yes
Yes
Yes(5)
0x00 8038
Yes
Yes(5)
0x00 803C
Yes
Yes
(5)
0x00 8040
Yes
(5)
0x00 8044
13
14
EXTI5
EXTI6
15
EXTI7
16
LCD
17
CLK/TIM1
18
ADC1
External interrupt 5
External interrupt 6
External interrupt 7
Yes
Yes
Yes
Yes
Yes
Yes
Yes
LCD interrupt
-
-
Yes
Yes
0x00 8048
system clock switch/
CSS interrupt/
TIM 1 break
-
-
Yes
Yes(5)
0x00 804C
ACD1
Yes
Yes
Yes
Yes(5)
0x00 8050
19
TIM2 update/overflow/
trigger/break
USART2 transmission
TIM2/USART2
complete/transmit data
register empty
interrupt
-
-
Yes
Yes(5)
0x00 8054
20
TIM2/USART2
-
-
Yes
Yes(5)
0x00 8058
capture/
compare/USART2 interrupt
DS9111 Rev 4
51/112
52
Interrupt vector mapping
STM8L052R8
Table 9. Interrupt mapping (continued)
IRQ
No.
Source
block
Description
Wakeup
from Halt
mode
Wakeup
Wakeup
Wakeup
from
from Wait from Wait
Active(WFI
(WFE
halt mode
mode)
mode)(1)
Vector
address
21
TIM3 update/overflow/
trigger/break USART3
transmission
TIM3/USART3
complete/transmit data
register empty
interrupt
-
-
Yes
Yes(5)
0x00 805C
22
TIM3
capture/compareUSART3
Receive register
TIM3/USART3
data full/overrun/idle line
detected/parity error/
interrupt
-
-
Yes
Yes(5)
0x00 8060
23
TIM1
Update /overflow/trigger/
COM
-
-
-
Yes(5)
0x00 8064
24
TIM1
Capture/compare
-
-
-
Yes(5)
0x00 8068
25
TIM4
TIM4 update/overflow/
trigger
-
-
Yes
Yes(5)
0x00 806C
26
SPI1
End of Transfer
Yes
Yes
Yes
Yes(5)
0x00 8070
27
USART1 transmission
complete/transmit data
USART1/TIM5 register empty/
TIM5 update/overflow/
trigger/break
-
-
Yes
Yes(5)
0x00 8074
28
USART1 received data
ready/overrun error/
USART1/TIM5 idle line detected/parity
error/TIM5
capture/compare
-
-
Yes
Yes(5)
0x00 8078
Yes
Yes
Yes
Yes(5)
0x00 807C
29
I2C1/SPI2
I2C1 interrupt(4)/SPI2
1. The Low power wait mode is entered when executing a WFE instruction in Low power run mode.
2. The TLI interrupt is the logic OR between TIM2 overflow interrupt, and TIM4 overflow interrupts.
3. The interrupt from PVD is logically OR-ed with Port E and F interrupts. Register EXTI_CONF allows to select between Port
E and Port F interrupt (see External interrupt port select register (EXTI_CONF) in the RM0031).
4. The device is woken up from Halt or Active-halt mode only when the address received matches the interface address.
5. In WFE mode, this interrupt is served if it has been previously enabled. After processing the interrupt, the processor goes
back to WFE mode. When this interrupt is configured as a wakeup event, the CPU wakes up and resumes processing.
52/112
DS9111 Rev 4
STM8L052R8
7
Option bytes
Option bytes
Option bytes contain configurations for device hardware features as well as the memory
protection of the device. They are stored in a dedicated memory block.
All option bytes can be modified in ICP mode (with SWIM) by accessing the EEPROM
address. See Table 10 for details on option byte addresses.
The option bytes can also be modified ‘on the fly’ by the application in IAP mode, except for
the ROP, UBC and PCODESIZE values which can only be taken into account when they are
modified in ICP mode (with the SWIM).
Refer to the STM8Lxx Flash programming manual (PM0054) and STM8 SWIM and Debug
Manual (UM0320) for information on SWIM programming procedures.
Table 10. Option byte addresses
Address
Option name
Option
byte
No.
Option bits
7
6
5
4
3
2
1
0
Factory
default
setting
00 4800
Read-out
protection
(ROP)
OPT0
ROP[7:0]
0x00
00 4802
UBC (User
Boot code size)
OPT1
UBC[7:0]
0x00
00 4807
PCODESIZE
OPT2
PCODE[7:0]
0x00
00 4808
Independent
watchdog
option
OPT3
[3:0]
Reserved
00 4809
Number of
stabilization
clock cycles for
HSE and LSE
oscillators
OPT4
Reserved
00 480A
Brownout reset
(BOR)
OPT5
[3:0]
Reserved
Bootloader
option bytes
(OPTBL)
OPTBL
[15:0]
00 480B
00 480C
WWDG WWDG IWDG
_HALT
_HW
_HALT
LSECNT[1:0]
BOR_TH
IWDG
_HW
HSECNT[1:0]
BOR_
ON
0x00
0x00
0x01
0x00
OPTBL[15:0]
DS9111 Rev 4
0x00
53/112
55
Option bytes
STM8L052R8
Table 11. Option byte description
Option
byte no.
Option description
OPT0
ROP[7:0] Memory readout protection (ROP)
0xAA: Disable readout protection (write access via SWIM protocol)
Refer to Readout protection section in the STM8L reference manual (RM0031).
OPT1
UBC[7:0] Size of the user boot code area
UBC[7:0] Size of the user boot code area
0x00: No UBC
0x01: Page 0 reserved for the UBC and write protected.
...
0xFF: Page 0 to 254 reserved for the UBC and write-protected.
Refer to User boot code section in the STM8L reference manual (RM0031).
OPT2
PCODESIZE[7:0] Size of the proprietary code area
0x00: No proprietary code area
0x01: Page 0 reserved for the proprietary code and read/write protected.
...
0xFF: Page 0 to 254 reserved for the proprietary code and read/write protected.
Refer to Proprietary code area (PCODE) section in the STM8L reference manual
(RM0031) for more details.
IWDG_HW: Independent watchdog
0: Independent watchdog activated by software
1: Independent watchdog activated by hardware
OPT3
IWDG_HALT: Independent watchdog off in Halt/Active-halt
0: Independent watchdog continues running in Halt/Active-halt mode
1: Independent watchdog stopped in Halt/Active-halt mode
WWDG_HW: Window watchdog
0: Window watchdog activated by software
1: Window watchdog activated by hardware
WWDG_HALT: Window window watchdog reset on Halt/Active-halt
0: Window watchdog stopped in Halt mode
1: Window watchdog generates a reset when MCU enters Halt mode
OPT4
54/112
HSECNT: Number of HSE oscillator stabilization clock cycles
0x00 - 1 clock cycle
0x01 - 16 clock cycles
0x10 - 512 clock cycles
0x11 - 4096 clock cycles
LSECNT: Number of LSE oscillator stabilization clock cycles
0x00 - 1 clock cycle
0x01 - 16 clock cycles
0x10 - 512 clock cycles
0x11 - 4096 clock cycles
DS9111 Rev 4
STM8L052R8
Option bytes
Table 11. Option byte description (continued)
Option
byte no.
OPT5
Option description
BOR_ON:
0: Brownout reset off
1: Brownout reset on
BOR_TH[3:1]: Brownout reset thresholds. Refer to Table 16 for details on the thresholds
according to the value of BOR_TH bits.
OPTBL
OPTBL[15:0]:
This option is checked by the boot ROM code after reset. Depending on the content of
addresses 00 480B, 00 480C and 0x8000 (reset vector) the CPU jumps to the
bootloader or to the reset vector.
Refer to the UM0560 bootloader user manual for more details.
DS9111 Rev 4
55/112
55
Electrical parameters
STM8L052R8
8
Electrical parameters
8.1
Parameter conditions
Unless otherwise specified, all voltages are referred to VSS.
8.1.1
Minimum and maximum values
Unless otherwise specified the minimum and maximum values are guaranteed in the worst
conditions of ambient temperature, supply voltage and frequencies by tests in production on
100% of the devices with an ambient temperature at TA= 25 °C and TA = TA max (given by
the selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes and are not tested in production. Based on
characterization, the minimum and maximum values refer to sample tests and represent the
mean value plus or minus three times the standard deviation (mean±3Σ).
8.1.2
Typical values
Unless otherwise specified, typical data are based on TA = 25 °C, VDD = 3 V. They are given
only as design guidelines and are not tested.
Typical ADC accuracy values are determined by characterization of a batch of samples from
a standard diffusion lot over the full temperature range, where 95% of the devices have an
error less than or equal to the value indicated (mean±2Σ).
8.1.3
Typical curves
Unless otherwise specified, all typical curves are given only as design guidelines and are
not tested.
8.1.4
Loading capacitor
The loading conditions used for pin parameter measurement are shown in Figure 5.
Figure 5. Pin loading conditions
STM8L PIN
50 pF
MSv45211V1
56/112
DS9111 Rev 4
STM8L052R8
8.1.5
Electrical parameters
Pin input voltage
The input voltage measurement on a pin of the device is described in Figure 6.
Figure 6. Pin input voltage
STM8L PIN
VIN
MSv45212V1
8.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in Table 12: Voltage characteristics,
Table 13: Current characteristics and Table 14: Thermal characteristics may cause
permanent damage to the device. These are stress ratings only and functional operation of
the device at these conditions is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
The device’s mission profile (application conditions) is compliant with the JEDEC JESD47
Qualification Standard, the extended mission profiles are available on demand.
Table 12. Voltage characteristics
Symbol
VDD- VSS
VIN(2)
VESD
Ratings
Min
Max
- 0.3
4.0
Input voltage on true open-drain pins
(PC0 and PC1)
VSS - 0.3
VDD + 4.0
Input voltage on five-volt tolerant (FT)
pins
VSS - 0.3
VDD + 4.0
Input voltage on any other pin
VSS - 0.3
4.0
External supply voltage
(including VDDA)(1)
Electrostatic discharge voltage
Unit
V
see Absolute maximum
ratings (electrical sensitivity)
on page 105
1. All power (VDD1, VDD2, VDD3, VDD4, VDDA) and ground (VSS1, VSS2, VSS3, VSS4, VSSA) pins must always
be connected to the external power supply.
2. VIN maximum must always be respected. Refer to Table 13. for maximum allowed injected current values.
DS9111 Rev 4
57/112
106
Electrical parameters
STM8L052R8
Table 13. Current characteristics
Symbol
Ratings
Max.
IVDD
Total current into VDD power line (source)
80
IVSS
Total current out of VSS ground line (sink)
80
Output current sunk by IR_TIM pin
(with high sink LED driver capability)
80
Output current sunk by any other I/O and control pin
25
IIO
Output current sourced by any I/Os and control pin
IINJ(PIN)
ΣIINJ(PIN)
- 25
Injected current on true open-drain pins (PC0 and PC1)(1)
- 5 / +0
Injected current on five-volt tolerant (FT) pins(1)
- 5 / +0
Injected current on any other pin (2)
- 5 / +5
Total injected current (sum of all I/O and control pins) (3)
Unit
mA
± 25
1. Positive injection is not possible on these I/Os. A negative injection is induced by VINVDD while a negative injection is induced by VIN> gmcrit
LSE crystal/ceramic resonator oscillator
The LSE clock can be supplied with a 32.768 kHz crystal/ceramic resonator oscillator. All
the information given in this paragraph is based on characterization results with specified
typical external components. In the application, the resonator and the load capacitors have
to be placed as close as possible to the oscillator pins in order to minimize output distortion
and startup stabilization time. Refer to the crystal resonator manufacturer for more details
(frequency, package, accuracy...).
Table 29. LSE oscillator characteristics
Symbol
Parameter
fLSE
Low speed external oscillator
frequency
RF
Feedback resistor
(1)(2)
Recommended load capacitance
C
IDD(LSE)
gm
LSE oscillator power consumption
Conditions
Min.
Typ.
Max.
Unit
-
-
32.768
-
kHz
ΔV = 200 mV
-
1.2
-
MΩ
-
-
8
-
pF
VDD = 1.8 V
-
450
-
VDD = 3 V
-
600
-
VDD = 3.6 V
-
750
-
-
3(3)
-
-
µA/V
VDD is stabilized
-
1
-
s
Oscillator transconductance
tSU(LSE)(4) Startup time
nA
1. C=CL1=CL2 is approximately equivalent to 2 x crystal CLOAD.
2. The oscillator selection can be optimized in terms of supply current using a high quality resonator with a small Rm value.
Refer to crystal manufacturer for more details.
3. Guaranteed by design.
4.
tSU(LSE) is the startup time measured from the moment it is enabled (by software) to a stabilized 32.768 kHz oscillation.
This value is measured for a standard crystal resonator and it can vary significantly with the crystal manufacturer.
78/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
Figure 17. LSE oscillator circuit diagram
fLSE
Rm
Lm
RF
CO
CL1
OSC_IN
Cm
gm
Resonator
Consumption
control
Resonator
STM8
OSC_OUT
CL2
Internal clock sources
Subject to general operating conditions for VDD, and TA.
High speed internal RC oscillator (HSI)
In the following table, data are based on characterization results, not tested in production,
unless otherwise specified.
Table 30. HSI oscillator characteristics
Symbol
Conditions(1)
Parameter
Min.
Typ.
Max.
Unit
-
16
-1 (2)
-
1 (2)
%
1.8 V ≤VDD ≤ 3.6 V,
-40 °C ≤TA ≤ 85 °C
-5
-
5
%
Trimming code ≠ multiple of 16
-
0.4
0.7
%
Trimming code = multiple of 16
-
± 1.5
%
Frequency
VDD = 3.0 V
VDD = 3.0 V, TA = 25 °C
ACCHSI
Accuracy of HSI
oscillator (factory
calibrated)
TRIM
HSI user trimming
step(3)
tsu(HSI)
HSI oscillator setup
time (wakeup time)
-
-
3.7
6 (4)
µs
IDD(HSI)
HSI oscillator power
consumption
-
-
100
140(4)
µA
fHSI
MHz
1. VDD = 3.0 V, TA = -40 to 85 °C unless otherwise specified.
2. Tested in production.
3. The trimming step differs depending on the trimming code. It is usually negative on the codes which are multiples of 16
(0x00, 0x10, 0x20, 0x30...0xE0). Refer to the AN3101 “STM8L15x internal RC oscillator calibration” application note for
more details.
4. Guaranteed by design.
DS9111 Rev 4
79/112
106
Electrical parameters
STM8L052R8
Figure 18. Typical HSI frequency vs. VDD
Low speed internal RC oscillator (LSI)
In the following table, data are based on characterization results, not tested in production.
Table 31. LSI oscillator characteristics
Symbol
fLSI
Parameter
Conditions(1)
Min.
Typ.
Max.
Unit
-
26
38
56
kHz
µs
%
Frequency
tsu(LSI)
LSI oscillator wakeup time
D(LSI)
LSI oscillator frequency
drift(3)
-
-
-
200(2)
0 °C ≤TA ≤ 85 °C
-12
-
11
1. VDD = 1.8 V to 3.6 V, TA = -40 to 85 °C unless otherwise specified.
2. Guaranteed by design..
3. This is a deviation for an individual part, once the initial frequency has been measured.
80/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
Figure 19. Typical LSI clock source frequency vs. VDD
0.04
25°C
85°C
-40°C
RC32K Check (MHz)
0.038
0.036
0.034
0.032
0.03
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VDD (V)
MS19116V2
8.3.5
Memory characteristics
TA = -40 to 85 °C unless otherwise specified.
Table 32. RAM and hardware registers
Symbol
VRM
Parameter
Data retention mode
(1)
Conditions
Min.
Typ.
Max.
Unit
Halt mode (or Reset)
1.8
-
-
V
1. Minimum supply voltage without losing data stored in RAM (in Halt mode or under Reset) or in hardware
registers (only in Halt mode). Guaranteed by characterization results.
DS9111 Rev 4
81/112
106
Electrical parameters
STM8L052R8
Flash memory
Table 33. Flash program and data EEPROM memory
Symbol
VDD
tprog
Iprog
tRET(2)
Parameter
Conditions
Min.
Typ.
fSYSCLK = 16 MHz
1.8
Programming time for 1 or 128 bytes (block)
erase/write cycles (on programmed byte)
-
Programming time for 1 to 128 bytes (block)
write cycles (on erased byte)
(1)
Unit
-
3.6
V
-
6
-
ms
-
-
3
-
ms
TA=+25 °C, VDD = 3.0 V
-
TA=+25 °C, VDD = 1.8 V
-
Data retention (program memory) after 100
erase/write cycles at TA=−40 to +85 °C
TRET=+85 °C
30(1)
-
-
Data retention (data memory) after 100000
erase/write cycles at TA=−40 to +85 °C
TRET=+85 °C
30(1)
-
-
100(1)
-
-
cycles
-
-
kcycles
Operating voltage
(all modes, read/write/erase)
Programming/ erasing consumption
(3)
Erase/write cycles (data memory)
0.7
-
mA
years
Erase/write cycles (program memory)
NRW
Max.
TA=−40 to +85 °C
(1)
100
(4)
1. Guaranteed by characterization results.
2. Conforming to JEDEC JESD22a117
3. The physical granularity of the memory is 4 bytes, so cycling is performed on 4 bytes even when a write/erase operation
addresses a single byte.
4. Data based on characterization performed on the whole data memory.
82/112
DS9111 Rev 4
STM8L052R8
8.3.6
Electrical parameters
I/O current injection characteristics
As a general rule, current injection to the I/O pins, due to external voltage below VSS or
above VDD (for standard pins) should be avoided during normal product operation.
However, in order to give an indication of the robustness of the microcontroller in cases
when abnormal injection accidentally happens, susceptibility tests are performed on a
sample basis during device characterization.
Functional susceptibility to I/O current injection
While a simple application is executed on the device, the device is stressed by injecting
current into the I/O pins programmed in floating input mode. While current is injected into
the I/O pin, one at a time, the device is checked for functional failures.
The failure is indicated by an out of range parameter: ADC error, out of spec current
injection on adjacent pins or other functional failure (for example reset, oscillator frequency
deviation, LCD levels, etc.).
The test results are given in the following table.
Table 34. I/O current injection susceptibility
Functional susceptibility
Symbol
IINJ
8.3.7
Description
Negative
injection
Positive
injection
Injected current on true open-drain pins
-5
+0
Injected current on all 5 V tolerant (FT) pins
-5
+0
Injected current on any other pin
-5
+5
Unit
mA
I/O port pin characteristics
General characteristics
Subject to general operating conditions for VDD and TA unless otherwise specified. All
unused pins must be kept at a fixed voltage: using the output mode of the I/O for example or
an external pull-up or pull-down resistor.
DS9111 Rev 4
83/112
106
Electrical parameters
STM8L052R8
Table 35. I/O static characteristics
Symbol
VIL
Parameter
Input low level voltage(2)
Conditions(1)
Min.
Typ.
Max.
Input voltage on true
open-drain pins (PC0
and PC1)
Vss-0.3
-
0.3 x VDD
Input voltage on fivevolt tolerant (FT) pins
Vss-0.3
-
0.3 x VDD
Input voltage on any
other pin
Vss-0.3
-
0.3 x VDD
-
5.2
-
5.5
Input voltage on true
open-drain pins (PC0
and PC1)
with VDD < 2 V
Input voltage on true
open-drain pins (PC0
and PC1)
with VDD ≥ 2 V
VIH
Input high level voltage (2)
Input voltage on fivevolt tolerant (FT) pins
with VDD < 2 V
Ilkg
Input leakage current (4)
RPU
Weak pull-up equivalent
resistor(2)(6)
CIO
I/O pin capacitance
0.70 x VDD
V
5.2
-
5.5
0.70 x VDD
-
VDD+0.3
Standard I/Os
-
200
-
True open drain I/Os
-
200
-
VSS≤VIN≤VDD
Standard I/Os
-
-
50 (5)
VSS≤VIN≤VDD
True open drain I/Os
-
-
200(5)
VSS≤VIN≤VDD
PA0 with high sink LED
driver capability
-
-
200(5)
30
45
60
kΩ
-
5
-
pF
Input voltage on any
other pin
Schmitt trigger voltage hysteresis (3)
0.70 x VDD
VIN=VSS
-
1. VDD = 3.0 V, TA = -40 to 85 °C unless otherwise specified.
2. Guaranteed by characterization results.
3. Hysteresis voltage between Schmitt trigger switching levels. Based on characterization results, not tested.
4. The max. value may be exceeded if negative current is injected on adjacent pins.
5. Not tested in production.
6. RPU pull-up equivalent resistor based on a resistive transistor (corresponding IPU current characteristics described in
Figure 23).
84/112
V
-
Input voltage on fivevolt tolerant (FT) pins
with VDD ≥ 2 V
Vhys
Unit
DS9111 Rev 4
mV
nA
STM8L052R8
Electrical parameters
Figure 20. Typical VIL and VIH vs. VDD (standard I/Os)
3
-40°C
25°C
2.5
85°C
VIL and VIH [V]
2
1.5
1
0.5
0
1.8
2.1
2.6
3.1
3.6
VDD [V]
ai18220c
Figure 21. Typical VIL and VIH vs. VDD (true open drain I/Os)
3
-40°C
25°C
85°C
VIL and VIH [V]
2.5
2
1.5
1
0.5
0
1.8
2.1
2.6
VDD [V]
3.1
3.6
ai18221V2
DS9111 Rev 4
85/112
106
Electrical parameters
STM8L052R8
Figure 22. Typical pull-up resistance RPU vs. VDD with VIN=VSS
60
-40°C
25°C
85°C
Pull-Up resistance [k7]
55
50
45
40
35
30
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
VDD [V]
ai18222V2
Figure 23. Typical pull-up current Ipu vs. VDD with VIN=VSS
120
-40°C
25°C
85°C
Pull-Up current [μA]
100
80
60
40
20
0
1.8
1.95 2.1
2.25 2.4
2.55 2.7 2.85
VDD [V]
3
3.15 3.3
3.45 3.6
ai18223V2
Output driving current
Subject to general operating conditions for VDD and TA unless otherwise specified.
86/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
Table 36. Output driving current (high sink ports)
I/O
Symbol
Type
Output low level voltage for an I/O pin
Standard
VOL (1)
Parameter
VOH (2) Output high level voltage for an I/O pin
Conditions
Min.
Max.
Unit
IIO = +2 mA,
VDD = 3.0 V
-
0.45
V
IIO = +2 mA,
VDD = 1.8 V
-
0.45
V
IIO = +10 mA,
VDD = 3.0 V
-
0.7
V
IIO = -2 mA,
VDD = 3.0 V
VDD-0.45
-
V
IIO = -1 mA,
VDD = 1.8 V
VDD-0.45
-
V
IIO = -10 mA,
VDD = 3.0 V
VDD-0.7
-
V
1. The IIO current sunk must always respect the absolute maximum rating specified in Table 13 and the sum
of IIO (I/O ports and control pins) must not exceed IVSS.
2. The IIO current sourced must always respect the absolute maximum rating specified in Table 13 and the
sum of IIO (I/O ports and control pins) must not exceed IVDD.
Table 37. Output driving current (true open drain ports)
Open drain
I/O
Symbol
Type
VOL
(1)
Parameter
Output low level voltage for an I/O pin
Conditions
Min.
Max.
IIO = +3 mA,
VDD = 3.0 V
-
0.45
IIO = +1 mA,
VDD = 1.8 V
-
Unit
V
0.45
1. The IIO current sunk must always respect the absolute maximum rating specified in Table 13 and the sum
of IIO (I/O ports and control pins) must not exceed IVSS.
Table 38. Output driving current (PA0 with high sink LED driver capability)
IR
I/O
Symbol
Type
VOL (1)
Parameter
Output low level voltage for an I/O pin
Conditions
Min.
Max.
Unit
IIO = +20 mA,
VDD = 2.0 V
-
0.45
V
1. The IIO current sunk must always respect the absolute maximum rating specified in Table 13 and the sum
of IIO (I/O ports and control pins) must not exceed IVSS.
DS9111 Rev 4
87/112
106
Electrical parameters
STM8L052R8
Figure 24. Typical VOL @ VDD = 3.0 V (high sink Figure 25. Typical VOL @ VDD = 1.8 V (high sink
ports)
ports)
1
-40°C
55
-40°C
25°C
85°C
VOL [V]
0.75
25°C
85°C
50
0.5
45
0.25
40
35
0
0
2
4
6
8
10
12
14
16
18
IOL [mA]
20
ai18226V2
30
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
Figure 26. Typical VOL @ VDD = 3.0 V (true open Figure 27. Typical VOL @ VDD = 1.8 V (true open
drain ports)
drain ports)
0.5
0.5
-40°C
25°C
85°C
0.4
0.4
-40°C
25°C
85°C
0.3
VOL [V]
VOL [V]
0.3
0.2
0.2
0.1
0.1
0
0
0
1
2
3
4
5
6
0
7
1
2
3
4
5
6
7
IOL [mA]
IOL [mA]
ai18229V2
ai18228V2
Figure 28. Typical VDD - VOH @ VDD = 3.0 V (high Figure 29. Typical VDD - VOH @ VDD = 1.8 V (high
sink ports)
sink ports)
2
0.5
-40°C
25°C
85°C
1.75
-40°C
25°C
85°C
1.25
0.4
VDD - VOH [V]
VDD - VOH [V]
1.5
1
0.75
0.3
0.2
0.5
0.1
0.25
0
0
0
2
4
6
8
10
12
14
16
18
20
0
IOH [mA]
1
2
3
4
5
6
ai18231V2
ai12830V2
NRST pin
Subject to general operating conditions for VDD and TA unless otherwise specified.
88/112
7
IOH [mA]
DS9111 Rev 4
STM8L052R8
Electrical parameters
Table 39. NRST pin characteristics
Symbol
Parameter
Conditions
Min.
Typ.
Max.
VIL(NRST)
NRST input low level voltage (1)
-
VSS
-
0.8
VIH(NRST)
NRST input high level voltage (1)
-
1.4
-
VDD
IOL = 2 mA
for 2.7 V ≤VDD ≤ 3.6 V
-
-
IOL = 1.5 mA
for VDD < 2.7 V
-
VOL(NRST)
NRST output low level voltage (1)
VHYST
NRST input hysteresis(3)
-
RPU(NRST)
NRST pull-up equivalent
resistor(1)
VF(NRST)
VNF(NRST)
Unit
V
0.4
-
10%VDD
(2)
-
-
mV
-
30
45
60
kΩ
NRST input filtered pulse (3)
-
-
-
50
NRST input not filtered pulse (3)
-
300
-
-
ns
1. Guaranteed by characterization results.
2. 200 mV min.
3. Guaranteed by design.
Figure
30. Typical NRST pull-up resistance RPU vs. VDD
55
Pull-up resistance [kΩ]
25°C
85°C
50
45
40
35
30
1.8
2
2.2
2.4
2.6
DS9111 Rev 4
2.8
3
VDD [V]
3.2
3.4
3.6
89/112
106
Electrical parameters
STM8L052R8
Figure 31. Typical NRST pull-up current Ipu vs. VDD
120
Pull-Up current [μA]
100
-40°C
25°C
85 °C
80
60
40
20
0
1.8
1.95 2.1
2.25 2.4
2.55 2.7
2.85
3
3.15 3.3
3.45 3.6
VDD [V]
ai18225V2
The reset network shown in Figure 32 protects the device against parasitic resets. The user
must ensure that the level on the NRST pin can go below the VIL max. level specified in
Table 39. Otherwise the reset is not taken into account internally. For power consumptionsensitive applications, the capacity of the external reset capacitor can be reduced to limit the
charge/discharge current. If the NRST signal is used to reset the external circuitry, the user
must pay attention to the charge/discharge time of the external capacitor to meet the reset
timing conditions of the external devices. The minimum recommended capacity is 10 nF.
90/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
Figure 32. Recommended NRST pin configuration
VDD
RPU
RSTIN
EXTERNAL
RESET
CIRCUIT
Filter
INTERNAL RESET
STM8L
0.1 µF
DS9111 Rev 4
91/112
106
Electrical parameters
8.3.8
STM8L052R8
Communication interfaces
SPI1 - Serial peripheral interface
Unless otherwise specified, the parameters given in Table 40 are derived from tests
performed under ambient temperature, fSYSCLK frequency and VDD supply voltage
conditions summarized in Section 8.3.1. Refer to I/O port characteristics for more details on
the input/output alternate function characteristics (NSS, SCK, MOSI, MISO).
Table 40. SPI1 characteristics
Symbol
Conditions(1)
Min.
Max.
Master mode
0
8
Slave mode
0
8
SPI1 clock rise and fall
time
Capacitive load: C = 30 pF
-
30
ns
tsu(NSS)(2)
NSS setup time
Slave mode
4 x 1/fSYSCLK
-
-
th(NSS)(2)
NSS hold time
Slave mode
80
-
-
SCK high and low time
Master mode,
fMASTER = 8 MHz, fSCK= 4 MHz
105
145
-
Master mode
30
-
-
Slave mode
3
-
-
Master mode
15
-
-
Slave mode
0
-
-
Data output access time
Slave mode
-
3x 1/fSYSCLK
-
30
-
-
fSCK
1/tc(SCK)
tr(SCK)
tf(SCK)
(2)
tw(SCKH)
tw(SCKL)(2)
Parameter
SPI1 clock frequency
tsu(MI) (2)
tsu(SI)(2)
Data input setup time
th(MI) (2)
th(SI)(2)
Data input hold time
ta(SO)
(2)(3)
tdis(SO)(2)(4)
Unit
MHz
Data output disable time
Slave mode
(2)
Data output valid time
Slave mode (after enable edge)
-
60
-
tv(MO)(2)
Data output valid time
Master mode (after enable
edge)
-
20
-
Slave mode (after enable edge)
15
-
-
Master mode (after enable
edge)
1
-
-
tv(SO)
th(SO)(2)
th(MO)(2)
Data output hold time
1. Parameters are given by selecting 10 MHz I/O output frequency.
2. Values based on design simulation and/or characterization results, and not tested in production.
3. Min. time is for the minimum time to drive the output and max. time is for the maximum time to validate the data.
4. Min. time is for the minimum time to invalidate the output and max. time is for the maximum time to put the data in Hi-Z.
92/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
Figure 33. SPI1 timing diagram - slave mode and CPHA=0
Figure 34. SPI1 timing diagram - slave mode and CPHA=1(1)
NSS input
SCK input
tSU(NSS)
CPHA=1
CPOL=0
CPHA=1
CPOL=1
tw(SCKH)
tw(SCKL)
th(SO)
tv(SO)
ta(SO)
MISO
OUTPUT
MSB OUT
BIT6 OUT
tr(SCK)
tf(SCK)
tdis(SO)
LSB OUT
th(SI)
tsu(SI)
MOSI
INPUT
th(NSS)
tc(SCK)
MSB IN
BIT 1 IN
LSB IN
ai14135b
1. Measurement points are done at CMOS levels: 0.3VDD and 0.7VDD.
DS9111 Rev 4
93/112
106
Electrical parameters
STM8L052R8
Figure 35. SPI1 timing diagram - master mode(1)
1. Measurement points are done at CMOS levels: 0.3VDD and 0.7VDD.
94/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
I2C - Inter IC control interface
Subject to general operating conditions for VDD, fSYSCLK, and TA unless otherwise specified.
The STM8L I2C interface (I2C1) meets the requirements of the Standard I2C communication
protocol described in the following table with the restriction mentioned below:
Refer to I/O port characteristics for more details on the input/output alternate function
characteristics (SDA and SCL).
Table 41. I2C characteristics
Symbol
Parameter
Standard mode I2C
Fast mode I2C(1)
Min.(2)
Max. (2)
Min. (2)
Max. (2)
Unit
tw(SCLL)
SCL clock low time
4.7
-
1.3
-
tw(SCLH)
SCL clock high time
4.0
-
0.6
-
tsu(SDA)
SDA setup time
250
-
100
-
th(SDA)
SDA data hold time
0
-
0
900
tr(SDA)
tr(SCL)
SDA and SCL rise time
-
1000
-
300
tf(SDA)
tf(SCL)
SDA and SCL fall time
-
300
-
300
th(STA)
START condition hold time
4.0
-
0.6
-
tsu(STA)
Repeated START condition setup
time
4.7
-
0.6
-
tsu(STO)
STOP condition setup time
4.0
-
0.6
-
μs
STOP to START condition time (bus
free)
4.7
-
1.3
-
μs
-
400
-
400
pF
tw(STO:STA)
Cb
Capacitive load for each bus line
μs
ns
μs
1. fSYSCLK must be at least equal to 8 MHz to achieve max fast I2C speed (400 kHz).
2. Data based on standard I2C protocol requirement, not tested in production.
Note:
For speeds around 200 kHz, the achieved speed can have a ± 5% tolerance.
For other speed ranges, the achieved speed can have a ± 2% tolerance.
The above variations depend on the accuracy of the external components used.
DS9111 Rev 4
95/112
106
Electrical parameters
STM8L052R8
Figure 36. Typical application with I2C bus and timing diagram 1)
VDD
VDD
4.7kΩ
4.7kΩ
I2C BUS
100Ω
SDA
100Ω
SCL
STM8L
REPEATED START
START
tsu(STA)
tw(STO:STA)
SDA
tr(SDA)
tf(SDA)
tsu(SDA)
th(SDA)
tr(SCL)
tf(SCL)
STOP
SCL
th(STA)
tw(SCLH)
tw(SCLL)
1. Measurement points are done at CMOS levels: 0.3 x VDD and 0.7 x VDD
96/112
DS9111 Rev 4
tsu(STO)
START
STM8L052R8
8.3.9
Electrical parameters
LCD controller
In the following table, data are guaranteed by design, not tested in production.
Table 42. LCD characteristics
Symbol
Parameter
Min.
Typ.
Max.
VLCD
LCD external voltage
-
-
3.6
VLCD0
LCD internal reference voltage 0
-
2.6
-
VLCD1
LCD internal reference voltage 1
-
2.7
-
VLCD2
LCD internal reference voltage 2
-
2.8
-
VLCD3
LCD internal reference voltage 3
-
3.0
-
VLCD4
LCD internal reference voltage 4
-
3.1
-
VLCD5
LCD internal reference voltage 5
-
3.2
-
VLCD6
LCD internal reference voltage 6
-
3.4
-
VLCD7
LCD internal reference voltage 7
-
3.5
-
CEXT
VLCD external capacitance
0.1
1
2
-
3
-
-
3
-
IDD
Supply
current(1)
at VDD = 1.8 V
(1)
Supply current
at VDD = 3 V
Unit
V
µF
µA
RHN(2)
High value resistive network (low drive)
-
6.6
-
MΩ
(3)
Low value resistive network (high drive)
-
240
-
kΩ
V33
Segment/Common higher level voltage
-
-
VLCDx
V34
Segment/Common 3/4 level voltage
-
3/4VLCDx
-
V23
Segment/Common 2/3 level voltage
-
2/3VLCDx
-
V12
Segment/Common 1/2 level voltage
-
1/2VLCDx
-
V13
Segment/Common 1/3 level voltage
-
1/3VLCDx
-
V14
Segment/Common 1/4 level voltage
-
1/4VLCDx
-
V0
Segment/Common lowest level voltage
0
-
-
RLN
V
1. LCD enabled with 3 V internal booster (LCD_CR1 = 0x08), 1/4 duty, 1/3 bias, division ratio= 64, all pixels
active, no LCD connected.
2. RHN is the total high value resistive network.
3. RLN is the total low value resistive network.
VLCD external capacitor
The application can achieve a stabilized LCD reference voltage by connecting an external
capacitor CEXT to the VLCD pin. CEXT is specified in Table 42.
DS9111 Rev 4
97/112
106
Electrical parameters
8.3.10
STM8L052R8
Embedded reference voltage
In the following table, data are based on characterization results, not tested in production,
unless otherwise specified.
Table 43. Reference voltage characteristics
Symbol
Parameter
Conditions
Min.
Typ.
Max.
Unit
IREFINT
Internal reference voltage
consumption
-
-
1.4
-
µA
TS_VREFINT(1)(2)
ADC sampling time when reading the
internal reference voltage
-
-
5
10
µs
IBUF(1)
Internal reference voltage buffer
consumption (used for ADC)
-
-
13.5
25
µA
VREFINT out
Reference voltage output
-
ILPBUF(1)
Internal reference voltage low power
buffer consumption (used for
comparators or output)
IREFOUT(1)(4)
1.202
(3)
1.224
-
-
Buffer output current
-
CREFOUT
Reference voltage output load
tVREFINT(1)
tBUFEN(1)(2)
STABVREFINT
STABVREFINT
(3)
V
730
1200
nA
-
-
1
µA
-
-
-
50
pF
Internal reference voltage startup
time
-
-
2
3
ms
Internal reference voltage buffer
startup time once enabled
-
-
-
10
µs
Stability of VREFINT over temperature
-40 °C ≤TA ≤ 85 °C
-
20
50
ppm/°C
Stability of VREFINT over temperature
0 °C ≤TA ≤ 50 °C
-
-
20
ppm/°C
Stability of VREFINT after 1000 hours
-
-
-
TBD
ppm
1. Guaranteed by design.
2. Defined when ADC output reaches its final value ±1/2LSB
3. Tested in production at VDD = 3 V ±10 mV.
4. To guarantee less than 1% VREFOUT deviation
98/112
1.242
DS9111 Rev 4
STM8L052R8
8.3.11
Electrical parameters
12-bit ADC1 characteristics
In the following table, data are guaranteed by design, not tested in production.
Table 44. ADC1 characteristics
Symbol
Parameter
VDDA
Analog supply voltage
VREF+
Reference supply
voltage
VREF-
Conditions
Min.
Typ.
Max.
Unit
-
1.8
-
3.6
V
2.4 V ≤VDDA≤ 3.6 V
2.4
-
VDDA
V
1.8 V≤VDDA≤ 2.4 V
VDDA
V
Lower reference voltage
-
VSSA
V
IVDDA
Current on the VDDA
input pin
-
-
-
-
IVREF+
Current on the VREF+
input pin
1000
400
-
-
1450
µA
700
(peak)(1)
µA
450
(average)(1)
µA
VAIN
Conversion voltage
range
-
0(2)
-
VREF+
-
TA
Temperature range
-
-40
-
85
°C
on PF0/1/2/3 fast
channels
-
-
50(3)
kΩ
on all other channels
-
-
on PF0/1/2/3 fast
channels
-
on all other channels
-
2.4 V≤VDDA≤3.6 V
without zooming
0.320
-
16
MHz
1.8 V≤VDDA≤2.4 V
with zooming
0.320
-
8
MHz
VAIN on PF0/1/2/3 fast
channels
-
-
1(3)(4)
MHz
VAIN on all other
channels
-
-
760(3)(4)
kHz
RAIN
CADC
fADC
fCONV
External resistance on
VAIN
Internal sample and hold
capacitor
ADC sampling clock
frequency
12-bit conversion rate
16
-
pF
-
fTRIG
External trigger
frequency
-
-
-
tconv
1/fADC
tLAT
External trigger latency
-
-
-
3.5
1/fSYSCLK
DS9111 Rev 4
99/112
106
Electrical parameters
STM8L052R8
Table 44. ADC1 characteristics (continued)
Symbol
tS
Parameter
Sampling time
Conditions
Min.
Typ.
Max.
Unit
VAIN PF0/1/2/3 fast
channels
VDDA < 2.4 V
0.43(3)(4)
-
-
µs
VAIN PF0/1/2/3 fast
channels
2.4 V ≤VDDA≤ 3.6 V
0.22(3)(4)
-
-
µs
VAIN on slow channels
VDDA < 2.4 V
0.86(3)(4)
-
-
µs
VAIN on slow channels
2.4 V ≤VDDA≤ 3.6 V
0.41(3)(4)
-
-
µs
-
12 + tS
1/fADC
16 MHz
1(3)
µs
tconv
12-bit conversion time
tWKUP
Wakeup time from OFF
state
-
-
-
3
µs
tIDLE(5)
Time before a new
conversion
-
-
-
∞
s
tVREFINT
Internal reference
voltage startup time
-
-
-
refer to
Table 43
ms
1. The current consumption through VREF is composed of two parameters:
- one constant (max 300 µA)
- one variable (max 400 µA), only during sampling time + 2 first conversion pulses.
So, peak consumption is 300+400 = 700 µA and average consumption is 300 + [(4 sampling + 2) /16] x 400 = 450 µA at
1Msps
2. VREF- must be tied to ground.
3. Minimum sampling and conversion time is reached for maximum RAIN= 0.5 kΩ..
4. Value obtained for continuous conversion on fast channel.
5. The time between 2 conversions, or between ADC ON and the first conversion must be lower than tIDLE.
100/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
In the following three tables, data are guaranteed by characterization result, not tested in
production.
Table 45. ADC1 accuracy with VDDA = 3.3 V to 2.5 V
Symbol
Parameter
Conditions
Typ.
Max.
1
1.6
Differential non linearity fADC = 8 MHz
1
1.6
fADC = 4 MHz
1
1.5
fADC = 16 MHz
1.2
2
fADC = 8 MHz
1.2
1.8
fADC = 4 MHz
1.2
1.7
fADC = 16 MHz
2.2
3.0
fADC = 8 MHz
1.8
2.5
fADC = 4 MHz
1.8
2.3
fADC = 16 MHz
1.5
2
fADC = 8 MHz
1
1.5
fADC = 4 MHz
0.7
1.2
1
1.5
fADC = 16 MHz
DNL
INL
Integral non linearity
TUE
Total unadjusted error
Offset
Offset error
fADC = 16 MHz
Gain
Gain error
fADC = 8 MHz
Unit
LSB
LSB
fADC = 4 MHz
Table 46. ADC1 accuracy with VDDA = 2.4 V to 3.6 V
Symbol
Parameter
Typ.
Max.
Unit
1
2
LSB
1.7
3
LSB
DNL
Differential non linearity
INL
Integral non linearity
TUE
Total unadjusted error
2
4
LSB
Offset
Offset error
1
2
LSB
Gain
Gain error
1.5
3
LSB
Table 47. ADC1 accuracy with VDDA = VREF+ = 1.8 V to 2.4 V
Symbol
Parameter
Typ.
Max.
Unit
DNL
Differential non linearity
1
2
LSB
INL
Integral non linearity
2
3
LSB
TUE
Total unadjusted error
3
5
LSB
Offset
Offset error
2
3
LSB
Gain
Gain error
2
3
LSB
DS9111 Rev 4
101/112
106
Electrical parameters
STM8L052R8
Figure 37. ADC1 accuracy characteristics
Figure 38. Typical connection diagram using the ADC
STM8L05xxx
VDD
RAIN(1)
Sample and hold ADC
converter
VT
0.6 V
RADC
AINx
VT
0.6 V
VAIN
Cparasitic
IL±50 nA
12-bit
converter
CADC(1)
ai17090e
1. Refer to Table 44 for the values of RAIN and CADC.
2. Cparasitic represents the capacitance of the PCB (dependent on soldering and PCB layout quality) plus the
pad capacitance (roughly 7 pF). A high Cparasitic value will downgrade conversion accuracy. To remedy
this, fADC should be reduced.
General PCB design guidelines
Power supply decoupling should be performed as shown in Figure 39 or Figure 40,
depending on whether VREF+ is connected to VDDA or not. Good quality ceramic 10 nF
capacitors should be used. They should be placed as close as possible to the chip.
102/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
Figure 39. Power supply and reference decoupling (VREF+ not connected to VDDA)
STM8L
V REF+
External
reference
1 μF // 10 nF
Supply
V DDA
1 μF // 10 nF
V SSA/V REF-
ai17031b
Figure 40. Power supply and reference decoupling (VREF+ connected to VDDA)
STM8L
VREF+/VDDA
Supply
1 μF // 10 nF
VREF–/VSSA
ai17032b
DS9111 Rev 4
103/112
106
Electrical parameters
8.3.12
STM8L052R8
EMC characteristics
Susceptibility tests are performed on a sample basis during product characterization.
Functional EMS (electromagnetic susceptibility)
Based on a simple running application on the product (toggling 2 LEDs through I/O ports),
the product is stressed by two electromagnetic events until a failure occurs (indicated by the
LEDs).
•
ESD: Electrostatic discharge (positive and negative) is applied on all pins of the device
until a functional disturbance occurs. This test conforms with the IEC 61000 standard.
•
FTB: A burst of fast transient voltage (positive and negative) is applied to VDD and VSS
through a 100 pF capacitor, until a functional disturbance occurs. This test conforms
with the IEC 61000 standard.
A device reset allows normal operations to be resumed. The test results are given in the
table below based on the EMS levels and classes defined in application note AN1709.
Designing hardened software to avoid noise problems
EMC characterization and optimization are performed at component level with a typical
application environment and simplified MCU software. It should be noted that good EMC
performance is highly dependent on the user application and the software in particular.
Therefore it is recommended that the user applies EMC software optimization and
prequalification tests in relation with the EMC level requested for his application.
Prequalification trials:
Most of the common failures (unexpected reset and program counter corruption) can be
reproduced by manually forcing a low state on the NRST pin or the Oscillator pins for 1
second.
To complete these trials, ESD stress can be applied directly on the device, over the range of
specification values. When unexpected behavior is detected, the software can be hardened
to prevent unrecoverable errors occurring (see application note AN1015).
Table 48. EMS data
Symbol
Parameter
Conditions
VFESD
VDD = 3.3 V, TA = +25 °C,
Voltage limits to be applied on
any I/O pin to induce a functional fCPU= 16 MHz,
disturbance
conforms to IEC 61000
VEFTB
Fast transient voltage burst limits
VDD = 3.3 V, TA = +25 °C,
to be applied through 100 pF on
Using HSI
fCPU = 16 MHz,
VDD and VSS pins to induce a
conforms to IEC 61000
Using HSE
functional disturbance
Level/
Class
2B
4A
2B
Electromagnetic interference (EMI)
Based on a simple application running on the product (toggling 2 LEDs through the I/O
ports), the product is monitored in terms of emission. This emission test is in line with the
norm IEC61967-2 which specifies the board and the loading of each pin.
104/112
DS9111 Rev 4
STM8L052R8
Electrical parameters
Table 49. EMI data (1)
Symbol
Parameter
SEMI
VDD = 3.6 V,
TA = +25 °C,
LQFP80
conforming to
IEC61967-2
Peak level
Monitored
frequency band
Conditions
Max vs.
Unit
16 MHz
0.1 MHz to 30 MHz
10
30 MHz to 130 MHz
4
130 MHz to 1 GHz
1
SAE EMI Level
dBμV
1.5
-
1. Not tested in production.
Absolute maximum ratings (electrical sensitivity)
Based on two different tests (ESD and LU) using specific measurement methods, the
product is stressed in order to determine its performance in terms of electrical sensitivity.
For more details, refer to the application note AN1181.
Electrostatic discharge (ESD)
Electrostatic discharges (a positive then a negative pulse separated by 1 second) are
applied to the pins of each sample according to each pin combination. The sample size
depends on the number of supply pins in the device (3 parts*(n+1) supply pin). Two models
can be simulated: human body model and charge device model. This test conforms to the
JESD22-A114A/A115A standard.
Table 50. ESD absolute maximum ratings
Symbol
Ratings
Conditions
VESD(HBM)
Electrostatic discharge voltage
(human body model)
VESD(CDM)
Electrostatic discharge voltage
(charge device model)
Maximum
value (1)
Unit
2000
TA = +25 °C
V
750
1. Guaranteed by characterization results.
Static latch-up
•
LU: 3 complementary static tests are required on 10 parts to assess the latch-up
performance. A supply overvoltage (applied to each power supply pin) and a current
injection (applied to each input, output and configurable I/O pin) are performed on each
sample. This test conforms to the EIA/JESD 78 IC latch-up standard. For more details,
refer to the application note AN1181.
Table 51. Electrical sensitivities
Symbol
LU
Parameter
Static latch-up class
DS9111 Rev 4
Class
II
105/112
106
Electrical parameters
8.4
STM8L052R8
Thermal characteristics
The maximum chip junction temperature (TJmax) must never exceed the values given in
Table 15: General operating conditions on page 59.
The maximum chip-junction temperature, TJmax, in degree Celsius, may be calculated using
the following equation:
TJmax = TAmax + (PDmax x ΘJA)
Where:
•
TAmax is the maximum ambient temperature in ° C
•
ΘJA is the package junction-to-ambient thermal resistance in ° C/W
•
PDmax is the sum of PINTmax and PI/Omax (PDmax = PINTmax + PI/Omax)
•
PINTmax is the product of IDD and VDD, expressed in Watts. This is the maximum chip
internal power.
•
PI/Omax represents the maximum power dissipation on output pins
Where:
PI/Omax = Σ (VOL*IOL) + Σ((VDD-VOH)*I OH),
taking into account the actual VOL/IOL and VOH/IOH of the I/Os at low and high level in
the application.
Table 52. Thermal characteristics(1)
Symbol
ΘJA
Parameter
Thermal resistance junction-ambient
LQFP 64- 10 x 10 mm
Value
Unit
48
°C/W
1. Thermal resistance is based on JEDEC JESD51-2 with 4-layer PCB in a natural convection environment.
106/112
DS9111 Rev 4
STM8L052R8
9
Package information
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at www.st.com. ECOPACK
is an ST trademark.
9.1
LQFP64 package information
Figure 41. LQFP64 – 10 x 10 mm, 64 pin low-profile quad flat package outline
D
ccc C
D1
A
A2
D3
48
33
32
49
b
L1
E3 E1 E
A1
L
64
17
Pin 1
1
16
c
MS19157V1
1. Drawing is not to scale.
DS9111 Rev 4
107/112
110
Package information
STM8L052R8
Table 53. LQFP64 – 10 x 10 mm, 64-pin low-profile quad flat package mechanical data
inches(1)
millimeters
Symbol
Min
Typ
Max
Min
Typ
Max
A
-
-
1.60
-
-
0.0630
A1
0.05
-
0.15
0.0020
-
0.0059
A2
1.35
1.40
1.45
0.0531
0.0551
0.0571
b
0.17
0.22
0.27
0.0067
0.0087
0.0106
c
0.09
0.20
0.0035
-
0.0079
D
-
12.00
-
-
0.4724
-
D1
-
10.00
-
-
0.3937
-
E
-
12.00
-
-
0.4724
-
E1
-
10.00
-
-
0.3937
-
e
-
0.50
-
-
0.0197
-
θ
0°
3.5°
7°
0°
3.5°
7°
L
0.45
0.60
0.75
0.0177
0.0236
0.0295
L1
-
1.00
-
-
0.0394
-
Number of pins
N
64
1. Values in inches are converted from mm and rounded to 4 decimal digits.
Figure 42. Recommended footprint
33
48
0.3
49
12.7
32
0.5
10.3
10.3
64
17
1.2
1
16
7.8
12.7
ai14909
1. Dimensions are in millimeters.
108/112
DS9111 Rev 4
STM8L052R8
Package information
Device marking for LQFP64
The following figure gives an example of topside marking orientation versus pin 1 identifier
location.
The printed markings may differ depending on the supply chain.
Other optional marking or inset/upset marks, which identify the parts throughout supply
chain operations, are not indicated below.
Figure 43. Example of package marking (package top view)
STM8L052
Product identification(1)
R8T6
Y WW
Pin 1 identifier
Date code
Z
Revision code
MSv62916V1
1. Parts marked as “ES” or “E” are not yet qualified and therefore not approved for use in production. ST is not
responsible for any consequences resulting from such use. In no event will ST be liable for the customer
using any of these engineering samples in production. ST's Quality department must be contacted prior to
any decision to use these engineering samples to run a qualification activity.
DS9111 Rev 4
109/112
110
Ordering information
10
STM8L052R8
Ordering information
Figure 44. Ordering information
Example:
STM8 L
052 R
8
T
6
Device family
STM8 microcontroller
Product type
L = Low power
Device subfamily
052: Devices with LCD
Pin count
R = 64 pins
Program memory size
8 = 64 Kbytes of Flash memory
Package
T = LQFP
Temperature range
6 = Industrial temperature range, –40 to 85 °C
For a list of available options (such as memory size, package) and orderable part numbers
or for further information on any aspect of this device, please go to www.st.com or contact
the nearest ST sales office.
110/112
DS9111 Rev 4
STM8L052R8
11
Revision history
Revision history
Table 54. Document revision history
Date
Revision
22-Jun-2012
1
Initial release.
2
Modified 12-bit ADC up to 1 Msps/27 channels, Table 1:
Medium High density value line STM8L05xxx low power
device features and peripheral counts and Section 3.9:
Analog-to-digital converter.
3
Updated
– Figure at Features section of the cover page
– Footnotes from Section 8: Electrical parameters
– Section 8.2: Absolute maximum ratings
– Table 1: High density value line STM8L05xxx low
power device features and peripheral counts
– Figure 4: Memory map
– Figure 5: Pin loading conditions
– Figure 6: Pin input voltage
– Figure 7: Power supply thresholds
– Figure 34: SPI1 timing diagram - slave mode and
CPHA=1(1)
4
Updated pin 21 row in Table 4: High density value line
STM8L05xxx pin description.
Updated Section 9: Package information and added
Device marking for LQFP64 section.
27-May-2013
27-Feb-2017
23-Apr-2019
Changes
DS9111 Rev 4
111/112
111
STM8L052R8
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other
product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2019 STMicroelectronics – All rights reserved
112/112
DS9111 Rev 4