STN9360

STN9360 High voltage fast-switching PNP power transistor Datasheet — production data Features ■ High voltage capability ■ Fast switching speed 4 Applications 1 ■ Lighting ■ Switch mode power supply 2 3 SOT-223 Description This device is a high voltage fast-switching PNP power transistor. It is manufactured using high voltage multi epitaxial planar technology for high switching speeds and medium voltage capability. It uses a cellular emitter structure with planar edge termination to enhance switching speeds while maintaining a wide RBSOA. The device is designed for use in lighting applications and low cost switch-mode power supplies. Table 1. I Figure 1. Internal schematic diagram Device summary Part number Marking Package Packaging STN9360 N9360 SOT-223 Tape and reel December 2012 This is information on a product in full production. Doc ID 023213 Rev 2 1/10 www.st.com 10 Electrical ratings 1 Electrical ratings Table 2. Absolute maximum ratings Symbol Parameter Unit Collector-emitter voltage (VBE = 0) -600 V VCEO Collector-emitter voltage (IB = 0) -600 V VEBO Emitter-base voltage (IC = 0) -7 V -0.5 A -1 A Base current -0.25 A IBM Base peak current (tP < 5 ms) -0.5 A PTOT Total dissipation at Ta = 25 °C 1.6 W TSTG Storage temperature -65 to 150 °C 150 °C Value Unit 78 °C/W ICM IB TJ Table 3. Symbol RthJA 1. Value VCES IC 2/10 STN9360 Collector current Collector peak current (tP < 5 ms) Max. operating junction temperature Thermal data Parameter Thermal resistance junction-ambient (1) max Device mounted on PCB area of 1 cm² . Doc ID 023213 Rev 2 STN9360 2 Electrical characteristics Electrical characteristics Tcase = 25 °C unless otherwise specified. Table 4. Symbol Electrical characteristics Parameter Test conditions Min. Typ. Max. Unit ICES Collector cut-off current VCE = -600 V (VBE = 0) -10 μA IEBO Emitter cut-off current (IC = 0) -1 μA Collector-emitter VCE(sus) (1) sustaining voltage (IB = 0) VEB = -7 V IC = -10 mA -600 V VCE(sat) (1) Collector-emitter saturation voltage IC = -100 mA IB = -10 mA -0.5 V VBE(sat) (1) Base-emitter saturation IC = -100 mA voltage IB = -10 mA -1 V hFE tr ts tf DC current gain Resistive load Rise time Storage time Fall time IC = -1 mA IC = -10 mA IC = -20 mA VCE = -5 V VCE = -5 V VCE = -5 V VCC=-200 V, IC=-0.1 A IB1=-10 mA, IB2=20 mA Tp=30 μs 170 200 120 45 3.15 160 ns μs ns 1. Pulse test: pulse duration ≤ 300 μs, duty cycle ≤ 2 %. Doc ID 023213 Rev 2 3/10 Electrical characteristics STN9360 2.1 Electrical characteristics (curves) Figure 2. Safe operating area Figure 3. Derating curve    3XOVHĆRSHUDWLRQ &ROOHFWRUĆSRZHUĆGLVVLSDWLRQĆ 3FĆ: ,F0D[  ,FĆ>$@ ,F0D[Ć&RQW ĆPV  ĆPV ƗV Ć)RUĆVLQJOHĆ QRQĆUHSHWLWLYHĆ SXOVH  — ĆĆV    Figure 4. 9FHĆ>9@               Output curves up to VCE= 0.5 V    Figure 5.  $0Y 7DPEƃ& $0Y Output curves up to VCE= 5 V AM16312v1 AM16313v1 0.5 0.5 0.4 0.4 0.3 IC (A) 0.2 0.3 IC (A) 0.2 Ib=10mA Steps. Ib=10mA Steps. 0.1 0.1 0 0 Figure 6. 0.1 0.2 0.3 VCE(V) 0.4 0 0 0.5 1 3 2 4 5 VCE(V) DC current gain (VCE = 1 V) Figure 7. DC current gain (VCE = 5 V) AM16314v1 1000 AM16315v1 1000 TJ= -55°C TJ= 25°C TJ=100°C hfe 100 hfe 100 10 10 TJ= -55°C TJ= 25°C TJ=100°C 1 0.001 0.1 0.01 1 1 0.001 IC(A) 4/10 0.1 0.01 IC(A) Doc ID 023213 Rev 2 1 STN9360 Figure 8. Electrical characteristics Collector-emitter saturation voltage Figure 9. Base-emitter saturation voltage AM16317v1 AM16316v1 1 1 0.9 0.8 0.7 VBE(sat)(V) VCE(sat)(V) hfe=5 0.1 0.5 0.4 hfe=5 TJ= -55°C 0.3 TJ= 25°C 0.2 TJ= 25°C 0.1 0 0.01 TJ=100°C TJ=100°C 0.01 0.01 0.6 0.1 1 TJ= -55°C 0.1 1 IC(A) IC(A) Figure 10. Base-emitter on voltage Figure 11. Capacitance variation AM16318v1 1  0.9 &LE 0.8 VBE(on)(V) 0.7  0.5 &ĆFDSDFLWDQFHĆ>ĆS)Ć@ 0.6 VCE=5V 0.4 0.3 TJ= -55°C 0.2 &RE  TJ= 25°C 0.1 0 0.0001 TJ=100°C 0.001 0.1 0.01 1   IC(A)   95ĆUHYHUVHĆYROWDJHĆ >Ć9Ć@Ć   $0Y Figure 12. Reverse biased safe operating area 0.6 0.5 Ic [A] 0.4 hfe = 2 Vbeoff = -5V Rbb = 0 Ω L=1mH Tj ≤ 125 °C 0.3 0.2 0.1 0 0 100 200 300 Vce [V] 400 500 600 700 800 AM10060v1 Doc ID 023213 Rev 2 5/10 Electrical characteristics 2.2 STN9360 Test circuits Figure 13. Resistive load switching test circuit 1. Fast electronic switching 2. Non-inductive resistor 6/10 Doc ID 023213 Rev 2 STN9360 3 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Doc ID 023213 Rev 2 7/10 Package mechanical data Table 5. STN9360 SOT-223 mechanical data mm Dim. Min. Typ. A Max. 1.80 A1 0.02 0.1 B 0.60 0.70 0.85 B1 2.90 3.00 3.15 c 0.24 0.26 0.35 D 6.30 6.50 6.70 e 2.30 e1 4.60 E 3.30 3.50 3.70 H 6.70 7.00 7.30 V 10° Figure 14. SOT-223 mechanical data drawing 0046067_M 8/10 Doc ID 023213 Rev 2 STN9360 4 Revision history Revision history Table 6. Document revision history Date Revision Changes 21-May-2012 1 Initial release. 06-Dec-2012 2 Document status promoted from preliminary data to datasheet. Doc ID 023213 Rev 2 9/10 STN9360 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 10/10 Doc ID 023213 Rev 2