STPIC6D595B1

STPIC6D595 Power logic 8-bit shift register Features ■ ■ ■ ■ ■ Low RDS(on): 4Ω typ Eight 100mA DMOS outputs 250mA current limit capability Device are cascadable Low power consumption SO-16 TSSOP16 DIP-16 Description This STPIC6D595 is a monolithic, mediumvoltage, low current power 8-bit shift register designed for use in systems that require relatively moderate load power such as LEDs. The device contains an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. Data transfers through both the shift and storage register clock (SRCK) and the register clock (RCK), respectively. The device transfers data out the serial output (SER OUT) port on the rising edge of SRCK. The storage register transfers data to the output buffer when shift register clear (CLR) is high. When CLR is low, the input shift register is cleared. When output enable (G) is held high, all data in the output buffer is held low and all drain output are off. When G is held low, data from the storage register is transparent to the output buffer. When data in the output buffers is low, the DMOS transistor outputs are off. When data is high, the DMOS transistor outputs have sink-current capability. The SER OUT allows for cascading of the data from the shift register to additional devices. Output are low-side, open-drain DMOS transistors with output ratings of 20V and 120mA continuous sink-current capability. Each output provides a 250 mA maximum current limit at TC = 25°C. The current limit decreases as the junction temperature increases for additional device protection. The device also provides up to 2.0KV of ESD protection when tested using the humanbody model. The STPIC6D595 is characterized for operation over the operating case temperature range of 40°C to 125°C. Table 1. Device summary Order code STPIC6D595M STPIC6D595MTR STPIC6D595TTR STPIC6D595B1 Package SO-16 (Tube) SO-16 (Tape & Reel) TSSOP16 (Tape & Reel) DIP-16 Packaging 50 parts per tube / 20 tube per box 2500 parts per reel 2500 parts per reel 2500 parts per reel September 2007 Rev 2 1/20 www.st.com 20 Contents STPIC6D595 Contents 1 2 Logic symbol and pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 2.2 2.3 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 3.2 DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 5 6 7 Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Typical operating circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 STPIC6D595 Logic symbol and pin configuration 1 Logic symbol and pin configuration Figure 1. Logic symbol and pin configuration 3/20 Maximum rating STPIC6D595 2 Maximum rating Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2.1 Absolute maximum ratings Table 2. Absolute Maximum Ratings Symbol VCC VI VDS IDS ID ID ID Pd Pd TJ TC Tstg TL Parameter Logic supply voltage (See Note 1) Logic input voltage range Power DMOS drain to source voltage (See Note 2) Continuous source to drain diode anode current Pulsed drain current, each output, all output ON (TC = 25°C) Continuous current, each output, All Output ON (TC = 25°C) Peak drain current single output (TC = 25°C) (See Note 3) Continuous total dissipation (TC ≤ 25°C) Continuous total dissipation (TC = 125°C) Operating virtual junction temperature range Operating case temperature range Storage temperature range Lead temperature 1.6mm (1/16inch) from case for 10 seconds Value 7 -0.3 to 7 20 250 250 100 250 1087 217 -40 to +150 -40 to +125 -65 to +150 260 Unit V V V mA mA mA mA mW mW °C °C °C °C 2.2 Thermal data Table 3. Thermal data Symbol Rth(JA) Parameter Thermal resistance junction-ambient Value 115 Unit °C/W 4/20 STPIC6D595 Maximum rating 2.3 Recommended operating conditions Table 4. Recommended operating conditions Symbol VCC VIH VIL IDP Parameter Logic supply voltage High level input voltage LoW Level Input Voltage Pulse drain output current (TC = 25°C, VCC = 5V,all outputs ON) (see Note 3, Note 4 ) Set-up Time, SER IN High Before SRCK ↑ (see Figure 3 and Figure 7) Hold Time, SER IN High Before G ↑ (see Figure Figure 3, Figure 6, Figure 7) Pulse duration (see Figure 7) Operating case temperature 20 20 40 -40 125 Min 4.5 0.85VCC 0 Max 5.5 VCC 0.15VCC 250 Unit V V V mA tsu th tW TC ns ns ns °C 5/20 Electrical characteristics STPIC6D595 3 3.1 Electrical characteristics DC characteristics Table 5. DC characteristics (VCC = 5V, TC = 25°C, unless otherwise specified.) Symbol V(BR)DSX VOH Parameter Drain-to-source breakdown voltage High level output voltage SER OUT Low level output voltage SER OUT Test conditions ID = 1mA IOH = -20 µAVCC = 4.5V IOH = -4 mAVCC = 4.5V IOH = 20 µAVCC = 4.5V IOH = 4 mAVCC = 4.5V 4.4 4 1 145 1 -1 23 100 300 100 -100 40 4.49 Min Typ Max 20 Unit V V V mV mV nA nA µA VOL IIH IIL ICC High level input current VCC = 5.5VVI = VCC Low level input current VCC = 5.5VVI = 0 Logic supply current VCC = 5.5V All outputs OFF or ON ICC(FRQ) fSRCK = 5MHzCL = 30pF Logic supply current at All outputs OFF frequency (See Figure 5,(1)) VDS(on) = 0.5VIN = ID TC=85°C (See Note 4, Note 5, Note 6) (1) 70 250 µA IN Nominal current 120 200 µA VDS = 20VVCC = 5.5V IDSX Off-state drain current VDS = 20VVCC =5.5V or 0V TC = 125°C ID = 50mAVCC = 4.5V ID = 50mAVCC = 4.5V TC = 125°C ID = 100mAVCC = 4.5V 0.02 0.5 3.4 4.8 3.5 1 1 4 6 6 µA µA Ω Ω Ω RDS(on) Static drain source on state resistance (See Note 4, and Note 5 ) 1. Not tested, specified by design 6/20 STPIC6D595 Electrical characteristics 3.2 Switching characteristics Table 6. Switching characteristics (VCC = 5V, TC = 25°C, unless otherwise specified.) Symbol tPHL tPLH tPHL-SDO tPLH-SDO tPLH-R_O tPHL-R_O tPLH-S_SO tPHL-S_SO tr tf Parameter Propagation delay time, high to low level output from G Propagation delay time, low to high level output from G Propagation delay time, Clock to SDO Propagation delay time, Clock to SDO CL = 30pFID = 75mA Propagation delay low to high (See Figure 3, level RCK to OUT Figure 4, Figure 5, Propagation delay high to low Figure 6,) level RCK to OUT Propagation delay low to high level SCK to SDO Propagation delay high to low level SCK to SDO Rise time, drain output Fall time, drain output Test conditions Min Typ 19 46 14 14 62 13 14 14 20 15 Max 30 70 20 20 90 18 20 20 30 20 Unit ns ns ns ns ns ns ns ns ns ns Note: 1 2 3 4 5 6 All voltage value are with respect to GND Each power DMOS source is internally connected to GND Pulse duration ≤ 100µs and duty cycle ≤ 2% Technique should limit TJ - TC to 10°C maximum These parameters are measured with voltage sensing contacts separate from the currentcarrying contacts. Nominal Current is defined for a consistent comparison between devices from different sources. It is the current that produces a voltage drop of 0.5V at TC = 85°C. 7/20 Logic diagram STPIC6D595 4 Logic diagram Figure 2. Logic diagram 8/20 STPIC6D595 Typical operating circuit 5 Typical operating circuit Figure 3. Typical operation mode test circuits Figure 4. Typical operation mode waveforms Note: 1 2 A) The word generator has the following characteristics: tr ≤ 10ns, tf ≤ 10ns, tW = 300ns, pulse repetition rate (PRR) = 5KHz, ZO = 50Ω B) CL includes probe and jig capacitance. 9/20 Typical operating circuit Figure 5. Typical operation mode test circuits STPIC6D595 Figure 6. Switching time waveform 10/20 STPIC6D595 Figure 7. Input setup and hold waveform Typical operating circuit SCLK tsu th tw tPHL-SDO / tPLH -SDO Note: 1 2 A) The word generator has the following characteristics: tr ≤ 10ns, tf ≤ 10ns, tW = 300ns, pulse repetition rate (PRR) = 5KHz, ZO = 50Ω B) CL includes probe and jig capacitance. 11/20 Typical operating circuit Figure 8. Input equivalent circuit STPIC6D595 Figure 9. Output equivalent circuit 12/20 STPIC6D595 Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 13/20 Package mechanical data STPIC6D595 Plastic DIP-16 (0.25) MECHANICAL DATA mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 TYP. MAX. inch P001C 14/20 STPIC6D595 Package mechanical data SO-16 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8° (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45° (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.25 1.64 0.46 0.25 0.013 0.007 0.019 0.004 MIN. inch TYP. MAX. 0.068 0.010 0.063 0.018 0.010 0016020D 15/20 Package mechanical data STPIC6D595 Tape & Reel SO-16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.45 10.3 2.1 3.9 7.9 12.8 20.2 60 22.4 6.65 10.5 2.3 4.1 8.1 0.254 0.406 0.082 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.262 0.414 0.090 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 16/20 STPIC6D595 Package mechanical data TSSOP16 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0˚ 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8˚ 0.75 0˚ 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8˚ 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0079 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 17/20 Package mechanical data STPIC6D595 Tape & Reel TSSOP16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.7 5.3 1.6 3.9 7.9 12.8 20.2 60 22.4 6.9 5.5 1.8 4.1 8.1 0.264 0.209 0.063 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.272 0.217 0.071 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 18/20 STPIC6D595 Revision history 7 Revision history Table 7. Document revision history Date 20-Jun-2007 06-Sep-2007 Revision 1 2 First release Change from Preliminary to final version Changes 19/20 STPIC6D595 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20