STPIC6D595TTR

STPIC6D595 Power logic 8-bit shift register Features ■ Low RDS(on): 4 Ω typ ■ Eight 100 mA DMOS outputs ■ 250 mA current limit capability ■ Devices are cascadable ■ Low power consumption ■ Footprint compatible with STPIC6C595 DIP-16 SO-16 Description This STPIC6D595 is a monolithic, mediumvoltage, low current power 8-bit shift register designed for use in systems that require relatively moderate load power such as LEDs. The device contains an 8-bit serial-in, parallel-out shift register that feeds an 8-bit D-type storage register. Data transfers through both the shift and storage register clock (SRCK) and the register clock (RCK), respectively. The device transfers data out the serial output (SER OUT) port on the rising edge of SRCK. The storage register transfers data to the output buffer when shift register clear (CLR) is high. When CLR is low, the input shift register is cleared. When output enable (G) is held high, all data in the output buffer is held low and all drain output are off. When G is held low, data from the storage register is transparent to the output buffer. Table 1. TSSOP16 When data in the output buffers is low, the DMOS transistor outputs are off. When data is high, the DMOS transistor outputs have sink-current capability. The SER OUT allows for cascading of the data from the shift register to additional devices. Output are low-side, open-drain DMOS transistors with output ratings of 20 V and 120 mA continuous sink-current capability. Each output provides a 250 mA maximum current limit at TC = 25 °C. The current limit decreases as the junction temperature increases for additional device protection. The device also provides up to 2.0 kV of ESD protection when tested using the human-body model. The STPIC6D595 is characterized for operation over the operating case temperature range of -40 °C to 125 °C. Device summary Order codes Package Packaging STPIC6D595MTR SO-16 (Tape and reel) 2500 parts per reel STPIC6D595TTR TSSOP16 (Tape and reel) 2500 parts per reel STPIC6D595B1R DIP-16 25 parts per tube November 2009 Doc ID 13663 Rev 3 1/21 www.st.com 21 Contents STPIC6D595 Contents 1 Logic symbol and pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 2.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.2 Switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 Typical operating circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 Typical performance and characteristics . . . . . . . . . . . . . . . . . . . . . . . 13 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2/21 Doc ID 13663 Rev 3 STPIC6D595 1 Logic symbol and pin configuration Logic symbol and pin configuration Figure 1. Pin configuration Figure 2. Logic symbol Doc ID 13663 Rev 3 3/21 Maximum rating 2 STPIC6D595 Maximum rating Stressing the device above the rating listed in the “absolute maximum ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2.1 Absolute maximum ratings Table 2. Absolute maximum ratings Symbol Value Unit 7 V -0.3 to 7 V Power DMOS drain to source voltage (See Note 2) 20 V ID Pulsed drain current, each output, all output ON (TC = 25 °C) 250 mA ID Continuous current, each output, all output ON (TC = 25 °C) 100 mA ID Peak drain current single output (TC = 25 °C) (See Note 3) 250 mA Pd Continuous total dissipation (TC ≤ 25 °C) 1087 mW Pd Continuous total dissipation (TC = 125 °C) 217 mW TJ Operating virtual junction temperature range -40 to +150 °C TC Operating case temperature range -40 to +125 °C Tstg Storage temperature range -65 to +150 °C 260 °C VCC VI VDS TL 2.2 Logic supply voltage (See Note 1) Logic input voltage range Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds Thermal data Table 3. Symbol Rth(JA) 4/21 Parameter Thermal data Parameter Thermal resistance junction-ambient Doc ID 13663 Rev 3 Package Values DIP-16 85 SO-16 107 TSSOP16 143 Unit °C/W STPIC6D595 2.3 Maximum rating Recommended operating conditions Table 4. Symbol Recommended operating conditions Parameter Min Max Unit 4.5 5.5 V VCC Logic supply voltage VIH High level input voltage 0.85VCC VCC V VIL Low level input voltage 0 0.15VCC V IDP Pulse drain output current (TC = 25 °C, VCC = 5 V, all outputs ON) (see Note 3, Note 4) 250 mA tsu Set-up time, SER IN high before SRCK ↑ (see Figure 4 and Figure 8) 10 ns th Hold time, SER IN high after SRCK ↑ (see Figure 4, Figure 7, Figure 8) 10 ns tW Pulse duration (see Figure 8) 40 ns TC Operating case temperature -40 Doc ID 13663 Rev 3 125 °C 5/21 Electrical characteristics STPIC6D595 3 Electrical characteristics 3.1 DC characteristics VCC = 5 V, TC = 25 °C, unless otherwise specified. Table 5. Symbol DC characteristics Parameter Test conditions Drain-to-source breakdown voltage ID = 1 mA VSD Source-to-drain diode forward voltage IF = 100 mA VOH High level output voltage SER OUT VOL Low level output voltage SER OUT V(BR)DSX Min Typ 0.85 IOH = -20 μA VCC = 4.5 V 4.4 IOH = -4 mA VCC = 4.5 V 4 Max Unit 20 V 1.2 V 4.49 V V IOH = 20 μA VCC = 4.5 V 1 100 mV IOH = 4 mA VCC = 4.5 V 145 300 mV IIH High level input current VCC = 5.5 V VI = VCC 1 100 nA IIL Low level input current VCC = 5.5 V VI = 0 -1 -100 nA ICC Logic supply current 23 40 μA 70 250 μA 120 200 mA VDS = 20 V VCC = 5.5 V or 0 V 0.02 1 μA VDS = 20 V VCC = 5.5 V or 0 V TC = 125 °C 0.5 1 μA ID = 50 mA VCC = 4.5 V 3.4 4 Ω ID = 50 mA VCC = 4.5 V TC = 125 °C 4.8 6 Ω ID = 100 mA VCC = 4.5 V 3.5 6 Ω ICC(FRQ) IN VCC = 5.5 V All outputs OFF or ON = 5 MHz CL = 30 pF f Logic supply current at SRCK All outputs OFF frequency (See Figure 6,(1)) VDS(on) = 0.5 VIN = ID TC = 85 °C (See Note 4, Note 5, Note 6) Nominal current (1) IDSX Off-state drain current RDS(on) Static drain source on state resistance (See Note 4, and Note 5) 1. Not tested, specified by design 6/21 Doc ID 13663 Rev 3 STPIC6D595 3.2 Electrical characteristics Switching characteristics VCC = 5 V, TC = 25 °C, unless otherwise specified. Table 6. Symbol Parameter Min Typ Max Unit tPHL Propagation delay time, high to low level output from G - 19 30 ns tPLH Propagation delay time, low to high level output from G - 46 70 ns tPHL-SDO Propagation delay time, clock to SDO - 19 25 ns tPLH-SDO Propagation delay time, clock to SDO - 46 60 ns tPLH-R_O CL = 30 pF ID = 75 mA Propagation delay low to high (See Figure 4, level RCK to OUT Figure 5, Figure 6, Propagation delay high to low Figure 7,) - 62 90 ns - 13 18 ns tPHL-R_O Note: Switching characteristics Test conditions level RCK to OUT tPLH-S_SO Propagation delay low to high level SCK to SDO - 14 20 ns tPHL-S_SO Propagation delay high to low level SCK to SDO - 14 20 ns tr Rise time, drain output - 20 30 ns tf Fall time, drain output - 15 20 ns 1 All voltage value are with respect to GND 2 Each power DMOS source is internally connected to GND 3 Pulse duration ≤ 100 μs and duty cycle ≤ 2% 4 Technique should limit TJ - TC to 10 °C maximum 5 These parameters are measured with voltage sensing contacts separate from the currentcarrying contacts. 6 Nominal Current is defined for a consistent comparison between devices from different sources. It is the current that produces a voltage drop of 0.5 V at TC = 85 °C. Doc ID 13663 Rev 3 7/21 Logic diagram 4 Logic diagram Figure 3. 8/21 STPIC6D595 Logic diagram Doc ID 13663 Rev 3 STPIC6D595 5 Note: Typical operating circuit Typical operating circuit Figure 4. Typical operation mode test circuits Figure 5. Typical operation mode waveforms 1 A) The word generator has the following characteristics: tr ≤ 10 ns, tf ≤ 10 ns, tW = 300 ns, pulse repetition rate (PRR) = 5 kHz, ZO = 50 Ω 2 B) CL includes probe and jig capacitance. Doc ID 13663 Rev 3 9/21 Typical operating circuit 10/21 STPIC6D595 Figure 6. Typical operation mode test circuits Figure 7. Switching time waveform Doc ID 13663 Rev 3 STPIC6D595 Typical operating circuit Figure 8. Input setup and hold waveform SRCK tsu th tw tPHL-SDO / tPLH -SDO Note: 1 A) The word generator has the following characteristics: tr ≤ 10 ns, tf ≤ 10 ns, tW = 300 ns, pulse repetition rate (PRR) = 5 kHz, ZO = 50 Ω 2 B) CL includes probe and jig capacitance. Doc ID 13663 Rev 3 11/21 Typical operating circuit Figure 9. STPIC6D595 Input equivalent circuit Figure 10. Output equivalent circuit 12/21 Doc ID 13663 Rev 3 STPIC6D595 6 Typical performance and characteristics Typical performance and characteristics Unless otherwise specified TJ = 25 °C Figure 11. Static drain-source on-state resistance vs logic supply voltage Figure 12. Supply current vs frequency Icc1000 (uA) 5 RDSon (Ω) TA = 125 °C 4.5 800 TA = 85 °C 4 600 3.5 TA = 25 °C 400 3 200 TA = -40 °C 2.5 2 4.5 5 5.5 6 6.5 0 7 (V) Vcc Figure 13. Supply current vs supply voltage 0.1 1 10 100 f1000 (MHz) Figure 14. Switching time vs case temperature 50 t(ns) Icc (mA) 0.1 tPLH 0.08 40 0.06 30 0.04 0.02 tPHL 20 tr 0 tf 4.5 5 5.5 Vcc (V) 6 10 4.50 Doc ID 13663 Rev 3 4.70 4.90 5.10 5.30 5.50 Vcc 13/21 Package mechanical data 7 STPIC6D595 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 14/21 Doc ID 13663 Rev 3 STPIC6D595 Package mechanical data Plastic DIP-16 (0.25) MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 0.77 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C Doc ID 13663 Rev 3 15/21 Package mechanical data STPIC6D595 SO-16 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.25 b 0.35 b1 0.19 a2 0.068 0.004 0.010 0.46 0.013 0.018 0.25 0.007 1.64 C MAX. 0.063 0.5 0.010 0.019 c1 45° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 e3 8.89 F 3.8 G L M 0.050 0.350 4.0 0.149 0.157 4.6 5.3 0.181 0.208 0.5 1.27 0.019 0.050 0.62 S 0.024 8° (max.) 0016020D 16/21 Doc ID 13663 Rev 3 STPIC6D595 Package mechanical data Tape & Reel SO-16 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.45 6.65 0.254 0.262 Bo 10.3 10.5 0.406 0.414 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Doc ID 13663 Rev 3 17/21 Package mechanical data STPIC6D595 TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0079 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0˚ L 0.45 A 0.60 0.0256 BSC 8˚ 0˚ 0.75 0.018 8˚ 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 18/21 Doc ID 13663 Rev 3 STPIC6D595 Package mechanical data Tape & Reel TSSOP16 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 6.7 6.9 0.264 0.272 Bo 5.3 5.5 0.209 0.217 Ko 1.6 1.8 0.063 0.071 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 Doc ID 13663 Rev 3 19/21 Revision history 8 STPIC6D595 Revision history Table 7. 20/21 Document revision history Date Revision Changes 20-Jun-2007 1 First release 06-Sep-2007 2 Change from Preliminary to final version 17-Nov-2009 3 Updated: Table 2, Table 3, Table 5, Table 6, Table 6, Figure 1, Figure 7, Figure 8 and Figure 9 Added: Figure 2, Figure 11, Figure 12, Figure 13 and Figure 14 Doc ID 13663 Rev 3 STPIC6D595 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 13663 Rev 3 21/21