STPS10L40CG-TR

STPS10L40C Low drop power Schottky rectifier Datasheet - production data Description A1 K Dual center tap Schottky rectifier suited for switch mode power supply and high frequency DC to DC converters. A2 K Packaged either in TO-220AB and D2PAK, this device is especially intended for use in low voltage, high frequency inverters, free wheeling and polarity protection applications. K A1 A2 Table 1: Device summary TO-220AB K K Symbol Value IF(AV) 2x5A VRRM 40 V Tj (max.) 150 °C VF (typ.) 0.36 V A2 A2 A1 A1 D2PAK Features     Low forward voltage drop meaning very small conduction losses Low dynamic losses as a result of the schottky barrier Avalanche capability specified ECOPACK®2 compliant component for D²PAK on demand April 2016 DocID9433 Rev 7 This is information on a product in full production. 1/12 www.st.com Characteristics 1 STPS10L40C Characteristics Table 2: Absolute ratings (limiting values, per diode, at 25 °C, unless otherwise specified) Symbol Parameter Value Unit VRRM Repetitive peak reverse voltage 40 V IF(RMS) Forward rms current 20 A IF(AV) Average forward current δ = 0.5, square wave TC = 140 °C IFSM Surge non repetitive forward current tp = 10 ms sinusoidal PARM Repetitive peak avalanche power tp = 10 µs, Tj = 125 °C Tstg Per diode 5 Per device 10 A 150 Storage temperature range 190 W -65 to +150 °C +150 °C Maximum operating junction temperature (1) Tj A Notes: (1)(dP tot/dTj) < (1/Rth(j-a)) condition to avoid thermal runaway for a diode on its own heatsink. Table 3: Thermal parameters Symbol Parameter Rth(j-c) Junction to case Rth(c) Coupling Value Per diode 3.0 Total 1.7 - 0.35 Unit °C/W °C/W When the diodes 1 and 2 are used simultaneously: ΔTj (diode1) = P(diode1) x Rth(j-c) (per diode) + P(diode2) x Rth(c) Table 4: Static electrical characteristics (per diode) Symbol IR(1) Parameter Test conditions Reverse leakage current VF(1) Forward voltage drop Tj = 25 °C Tj = 100 °C VR = VRRM IF = 5 A - IF = 5 A - Tj = 25 °C IF = 10 A - Tj = 125 °C IF = 10 A - To evaluate the conduction losses use the following equation: P = 0.33 x IF(AV) + 0.026 IF2(RMS) 2/12 - Tj = 100 °C test: tp = 380 µs, δ < 2% DocID9433 Rev 7 Typ. - Tj = 25 °C Notes: (1)Pulse Min. 8 Max. Unit 0.2 mA 25 mA 0.53 0.36 0.46 0.67 0.49 0.59 V STPS10L40C 1.1 Characteristics Characteristics (curves) Figure 1: Average forward power dissipation versus average forward current (per diode) 3.5 Figure 2: Average forward current versus ambient temperature (δ = 0.5, per diode) PF(AV)(W) δ = 0.1 3.0 IF(AV)(A) 6 δ = 0.2 Rth(j-a) = Rth(j-c) δ = 0.5 δ = 0.05 5 2.5 4 δ =1 2.0 Rth(j-a) = 15 °C/W 3 1.5 2 T 1.0 T 1 0.5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 δ = tp/T tp δ = tp/T IF(AV)(A) 0.0 0.0 4.0 4.5 5.0 5.5 6.0 6.5 Figure 3: Normalized avalanche power derating versus pulse duration (Tj = 125 °C) 1 Tamb(°C) tp 0 0 25 50 75 100 125 150 Figure 4: Relative variation of thermal impedance junction to case versus pulse duration PARM (t p ) PARM (10 µs) Zth(j-c)/Rth(j-c) 1.0 0.8 0.1 δ= 0.5 0.6 0.4 δ = 0.2 0.01 δ = 0.1 T 0.2 single pulse t p (µs) t p(s ) 0.001 1 10 100 0.0 1E-3 1000 Figure 5: Reverse leakage current versus reverse voltage applied (typical values, per diode) IR(mA) 1E+2 1E-2 δ = tp/T 1E-1 1E+0 Figure 6: Junction capacitance versus reverse voltage applied (typical values, per diode) 1000 C(pF) F = 1 MHz V = 30 mV OSC RMS T = 25 °C j Tj = 150 °C 1E+1 tp Tj = 100 °C 1E+0 100 1E-1 Tj = 25 °C 1E-2 VR(V) VR(V) 1E-3 10 0 5 10 15 20 25 30 35 40 DocID9433 Rev 7 1 2 5 10 20 50 3/12 Characteristics STPS10L40C Figure 7: Forward voltage drop versus forward current (maximum values, per diode) Figure 8: Thermal resistance junction to ambient versus copper surface under tab for D²PAK 80 Rth(j-a) (°C/W) D²PAK 70 60 50 40 30 20 Epoxy printed board FR4, e CU= 35 µm 10 SCu(cm²) 0 0 4/12 DocID9433 Rev 7 5 10 15 20 25 30 35 40 Package information STPS10L40C 2 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.     Cooling method: by conduction (C) Epoxy meets UL 94,V0 Recommended torque value: 0.55 N·m (for TO-220AB) Maximum torque value: 0.7 N·m (for TO-220AB) DocID9433 Rev 7 5/12 Package information 2.1 STPS10L40C D²PAK package information Figure 9: D²PAK package outline This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. 6/12 DocID9433 Rev 7 Package information STPS10L40C Table 5: D²PAK package mechanical data Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A 4.36 4.60 0.172 0.181 A1 0.00 0.25 0.000 0.010 b 0.70 0.93 0.028 0.037 b2 1.14 1.70 0.045 0.067 c 0.38 0.69 0.015 0.027 c2 1.19 1.36 0.047 0.053 D 8.60 9.35 0.339 0.368 D1 6.90 8.00 0.272 0.311 D2 1.10 1.50 0.043 0.060 E 10.00 10.55 0.394 0.415 E1 8.10 8.90 0.319 0.346 E2 6.85 7.25 0.266 0.282 e 2.54 typ. 0.100 e1 4.88 5.28 0.190 0.205 H 15.00 15.85 0.591 0.624 J1 2.49 2.90 0.097 0.112 L 1.90 2.79 0.075 0.110 L1 1.27 1.65 0.049 0.065 L2 1.30 1.78 0.050 0.070 R V2 0.4 typ. 0° 0.015 8° DocID9433 Rev 7 0° 8° 7/12 Package information STPS10L40C Figure 10: D²PAK recommended footprint (dimensions in mm) 8/12 DocID9433 Rev 7 Package information STPS10L40C 2.2 TO-220AB package information Figure 11: TO-220AB package outline DocID9433 Rev 7 9/12 Package information STPS10L40C Table 6: TO-220AB package mechanical data Dimensions Ref. Millimeters Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 b 0.61 0.88 0.240 0.035 b1 1.14 1.70 0.045 0.067 c 0.48 0.70 0.019 0.028 D 15.25 15.75 0.600 0.620 D1 10/12 Inches 1.27 typ. 0.050 typ. E 10.00 10.40 0.394 0.409 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.195 0.203 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.260 J1 2.40 2.72 0.094 0.107 L 13.00 14.00 0.512 0.551 L1 3.50 3.93 0.138 0.155 L20 16.40 typ. 0.646 typ. L30 28.90 typ. 1.138 typ. θP 3.75 3.85 0.148 0.152 Q 2.65 2.95 0.104 0.116 DocID9433 Rev 7 Ordering information STPS10L40C 3 Ordering information Table 7: Ordering information Order code 4 Marking Package Weight Base qty. Delivery mode STPS10L40CT STPS10L40CT TO-220AB 1.95 g 50 Tube STPS10L40CG-TR STPS10L40CG D2PAK 1.38 g 1000 Tape and reel Revision history Table 8: Document revision history Date Revision Jul-2003 5B 23-Mar-2007 6 Removed ISOWATT packages. 7 Removed DPAK package. Updated features and packages silhouette in cover page. Updated Section 1: "Characteristics" and Section 1.1: "Characteristics (curves)". Updated Section 2.1: "D²PAK package information". 08-Apr-2016 Changes Last release. DocID9433 Rev 7 11/12 STPS10L40C IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved 12/12 DocID9433 Rev 7