STPS41L30CG

® STPS41L30CG/CT/CR LOW DROP POWER SCHOTTKY RECTIFIER MAIN PRODUCTS CHARACTERISTICS IF(AV) VRRM Tj (max) VF (max) 2 x 20 A 30 V 150 °C 0.38 V A1 K A2 FEATURES AND BENEFITS VERY SMALL CONDUCTION LOSSES NEGLIGIBLE SWITCHING LOSSES EXTREMELY FAST SWITCHING LOW FORWARD VOLTAGE DROP HIGH AVALANCHE CAPABILITY LOW THERMAL RESISTANCE AVALANCHE CAPABILITY SPECIFIED s s s s s s s A2 A1 K A1 K A2 I2PAK STPS41L30CR K TO-220AB STPS41L30CT DESCRIPTION Dual center tab Schottky rectifier suited for Switch Mode Power Supply and high frequency DC to DC converters. Packaged in D2PAK, I2PAK and TO-220ABthis device is intended for use in low voltage, high frequency inverters, free-wheeling and polarity protection applications. ABSOLUTE RATINGS (limiting values, per diode) Symbol VRRM IF(RMS) IF(AV) IFSM IRRM PARM Tstg Tj dV/dt *: Parameter Repetitive peak reverse voltage RMS forward current Average forward current Surge non repetitive forward current Peak repetitive reverse current Repetitive peak avalanche power Storage temperature range Maximum operating junction temperature * Critical rate of rise reverse voltage Tc = 135°C δ = 0.5 A2 A1 D2PAK STPS41L30CG Value 30 30 Per diode Per device 20 40 220 1 6500 - 65 to + 175 150 10000 Unit V A A A A W °C °C V/µs tp = 10 ms sinusoidal tp=2 µs square F=1kHz tp = 1µs Tj = 25°C dPtot 1 thermal runaway condition for a diode on its own heatsink < dTj Rth( j − a ) 1/6 July 2003 - Ed : 3A STPS41L30CG / STPS41L30CT / STPS41L30CR THERMAL RESISTANCES Symbol Rth(j-c) Junction to case Rth(c) Coupling Parameter Per diode Total Value 1.5 0.8 0.1 Unit °C/W When the diodes 1 and 2 are used simultaneously : ∆ Tj(diode 1) = P(diode1) x Rth(j-c)(Per diode) + P(diode 2) x Rth(c) STATIC ELECTRICAL CHARACTERISTICS (per diode) Symbol IR * VF * Parameter Reverse leakage current Forward voltage drop Tests Conditions Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Tj = 25°C Tj = 125°C Pulse test : * tp = 380 µs, δ < 2% Min. Typ. 170 VR = VRRM IF = 20 A IF = 20 A IF = 40 A IF = 40 A 0.47 0.35 Max. 1.5 350 0.48 0.38 0.57 0.49 Unit mA mA V To evaluate the conduction losses use the following equation : P = 0.27 x IF(AV) + 0.0055 IF2(RMS) Fig. 1: Conduction losses versus average current. PF(av)(W) 11 10 9 8 7 6 5 4 3 2 1 0 0 5 10 15 T Fig. 2: Average forward current versus ambient temperature (δ = 0.5). IF(av)(A) 25 Rth(j-a)=Rth(j-c) δ = 0.5 δ = 0.2 δ = 0.1 δ = 0.05 δ=1 20 15 10 Rth(j-a)=50°C/W 5 tp T IF(av)(A) δ=tp/T 20 0 δ=tp/T 0 25 tp Tamb(°C) 50 75 100 125 150 25 Fig. 3: Normalized avalanche power derating versus pulse duration. PARM(tp) PARM(1µs) 1 Fig. 4: Normalized avalanche power derating versus junction temperature. PARM(tp) PARM(25°C) 1.2 1 0.1 0.8 0.6 0.01 0.4 0.2 0.001 0.01 0.1 1 tp(µs) 10 100 1000 Tj(°C) 0 0 25 50 75 100 125 150 2/6 STPS41L30CG / STPS41L30CT / STPS41L30CR Fig. 5: Non repetitive surge peak forward current versus overload duration (maximum values). IM(A) 300 Fig. 6: Relative variation of thermal impedance junction to case versus pulse duration. Zth(j-c)/Rth(j-c) 1.0 0.9 250 0.8 0.7 0.6 Tc=25°C 200 δ = 0.5 150 Tc=75°C 0.5 0.4 0.3 Tc=125°C δ = 0.2 δ = 0.1 100 IM t 50 0.2 Single pulse T δ=0.5 t(s) 1.E-02 1.E-01 1.E+00 0.1 0.0 1.E-03 1.E-02 tp(s) 1.E-01 0 1.E-03 δ=tp/T tp 1.E+00 Fig. 7: Reverse leakage current versus reverse voltage applied (typical values). IR(mA) 1.E+03 Tj=150°C Fig. 8: Junction capacitance versus reverse voltage applied (typical values). C(nF) 10.0 F=1MHz Vosc=30mV Tj=25°C 1.E+02 Tj=125°C Tj=100°C 1.E+01 Tj=75°C 1.0 1.E+00 Tj=50°C 1.E-01 Tj=25°C VR(V) 1.E-02 0 5 10 15 20 25 30 0.1 1 VR(V) 10 100 Fig. 9: Forward voltage drop versus forward current. Fig. 10: Thermal resistance junction to ambient versus copper surface under tab (epoxy printed board FR4, Cu = 35µm) (STPS41L30CG only). Rth(j-a)(°C/W) 80 70 IFM(A) 100 Tj=125°C (Maximum values) 60 50 Tj=25°C (Maximum values) Tj=125°C (Typical values) 10 40 30 20 VFM(V) 1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 10 0 0 5 10 15 S(cm²) 20 25 30 35 40 3/6 STPS41L30CG / STPS41L30CT / STPS41L30CR PACKAGE MECHANICAL DATA D2PAK DIMENSIONS REF. A E L2 Millimeters Min. Max. 4.60 2.69 0.23 0.93 1.70 0.60 1.36 9.35 10.40 5.28 15.85 1.40 1.75 3.20 8° 4.40 2.49 0.03 0.70 1.14 0.45 1.23 8.95 10.00 4.88 15.00 1.27 1.40 2.40 0° Inches Min. 0.173 0.098 0.001 0.027 0.045 0.017 0.048 0.352 0.393 0.192 0.590 0.050 0.055 0.094 0° Max. 0.181 0.106 0.009 0.037 0.067 0.024 0.054 0.368 0.409 0.208 0.624 0.055 0.069 0.126 8° A C2 A1 A2 D B B2 C L L3 A1 B2 B G A2 C R C2 D E G L L2 M * V2 L3 M R V2 * FLAT ZONE NO LESS THAN 2mm 0.40 typ. 0.016 typ. FOOTPRINT (dimensions in mm) 16.90 10.30 1.30 5.08 3.70 8.90 4/6 STPS41L30CG / STPS41L30CT / STPS41L30CR PACKAGE MECHANICAL DATA I2PAK DIMENSIONS REF. A E L2 c2 Millimeters Min. Max. 4.60 2.69 0.93 1.17 1.17 0.60 1.36 9.35 2.70 10.4 13.6 3.78 1.40 4.40 2.49 0.70 1.14 1.14 0.45 1.23 8.95 2.40 10.0 13.1 3.48 1.27 Inches Min. 0.173 0.098 0.028 0.044 0.044 0.018 0.048 0.352 0.094 0.394 0.516 0.137 0.050 Max. 0.181 0.106 0.037 0.046 0.046 0.024 0.054 0.368 0.106 0.409 0.535 0.149 0.055 A A1 b b1 b2 c c2 D L1 b2 L b1 b e A1 D e E L c L1 L2 5/6 STPS41L30CG / STPS41L30CT / STPS41L30CR PACKAGE MECHANICAL DATA TO-220AB DIMENSIONS REF. H2 Dia L5 C L7 L6 L2 F2 F1 L9 L4 F G1 G M E D A Millimeters Min. Max. 4.40 4.60 1.23 1.32 2.40 2.72 0.49 0.70 0.61 0.88 1.14 1.70 1.14 1.70 4.95 5.15 2.40 2.70 10 10.40 16.4 typ. 13 14 2.65 2.95 15.25 15.75 6.20 6.60 3.50 3.93 2.6 typ. 3.75 3.85 Inches Min. Max. 0.173 0.181 0.048 0.051 0.094 0.107 0.019 0.027 0.024 0.034 0.044 0.066 0.044 0.066 0.194 0.202 0.094 0.106 0.393 0.409 0.645 typ. 0.511 0.551 0.104 0.116 0.600 0.620 0.244 0.259 0.137 0.154 0.102 typ. 0.147 0.151 A C D E F F1 F2 G G1 H2 L2 L4 L5 L6 L7 L9 M Diam. Ordering type STPS41L30CG STPS41L30CG-TR STPS41L30CT STPS41L30CR s Marking STPS41L30CG STPS41L30CG STPS41L30CT STPS41L30CR Package D PAK D PAK TO-220AB I PAK 2 2 2 Weight 1.48 g 1.48 g 2.20 g 1.49 g Base qty 50 1000 50 50 Delivery mode Tube Tape & reel Tube Tube EPOXY MEETS UL94,V0 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All rights reserved. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 6/6