STSR2PMCD

STSR2P/ STSR2PM FORWARD SYNCHRONOUS RECTIFIERS SMART DRIVER ■ ■ ■ ■ ■ ■ SUPPLY VOLTAGE RANGE: 4.5V TO 5.5V TYPICAL PEAK OUTPUT CURRENT: SOURCE -2A, SINK 3.5A OPERATING FREQUENCY: 20 TO 750 KHZ SMART TURN-OFF ANTICIPATION TIMING OPERATION INDEPENDENT FROM THE FORWARD MAGNETIC RESET TECHNIQUE POSSIBILITY TO OPERATE IN DISCONTINUOUS MODE SO-8 anticipation in turning-off the OUT GATE1 with respect to the clock signal transition is provided, while the anticipation in turning off the OUTGATE2 can be set through external components. The adopted transitions revelation mechanism makes circuit operation independent by the forward magnetic reset technique used, avoiding most of the common problems inherent in self-driven synchronous rectifiers. A special Inhibit function allows the shut-off of OUTGATE2. This feature makes discontinuous conduction mode possible and prevents the freewheeling mosfet from sinking current from the output. STSR2P automatically turns off the outputs when duty-cycle is lower than 13%, while STSR2PM works even at very low duty-cycle values. DESCRIPTION STSR2P Smart Driver IC provides two complementary high current outputs to drive Power Mosfets. The IC is dedicated to properly drive secondary Synchronous Rectifiers in medium power, low output voltage, high efficiency Forward Converters. From a synchronizing clock input, STSR2P generates two driving signals with the self-setting of dead time between complementary pulses. The IC operation prevents secondary side shoot-through conditions providing proper timing at the outputs turn-off transition. This smart function operates through a fast cycle-after-cycle control logic mechanism based on an internal high frequency oscillator, synchronized by the clock signal. A fixed SCHEMATIC DIAGRAM Vcc 2 5.7V + BIAS UVLO CK 4 PEAK DETECTOR ANTICIPATION SET + + 1 OUTGate1 HIGH FREQUENCY OSCILLATOR INHIBIT 5 3 SETANT2 DIGITAL CONTROL OUTPUT BUFFERS 7 OUTGate2 + 25mV 6 SGLGND September 2003 8 PWRGND 1/12 STSR2P/STSR2PM ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value DC Input Voltage VOUTGATE Max Gate Drive Output Voltage VINHIBIT Max INHIBIT Voltage (*) VCK Clock Input Voltage Range (*) ILX Switching Peak Current Unit -0.3 to 6 V -0.3 to VCC -0.6 to VCC V -0.3 to VCC 2 V 270 mW V A ±1 ±0.9 KV KV Tstg Continuous Power Dissipation at TA=105°C without heatsink Human Body Model Pins 1,2, 4, 5, 6, 7, 8 Pin 3 Storage Temperature Range -55 to +150 °C Top Operating Junction Temperature Range -40 to +125 °C PTOT ESD Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. (*) A higher positive voltage level can be applied to the pin with a resistor which limits the current flowing into the pin to 10mA maximum THERMAL DATA Symbol SO-8 Unit Rthj-amb Thermal Resistance Junction-case Parameter 40 °C/W Rthj-amb Thermal Resistance Junction-ambient (*) 160 °C/W (*) This value is referred to one layer pcb board with minimum copper connections for the leads. a minimum value of 120 °C/W can be obtained improving thermal conductivity of the board ORDERING CODES TYPE SO-8 SO-8 (T&R) STSR2P STSR2PM STSR2PCD STSR2PMCD STSR2PCD-TR STSR2PMCD-TR CONNECTION DIAGRAM (top view) 2/12 STSR2P/STSR2PM PIN DESCRIPTION Pin N° Symbol 1 OUTGATE1 2 VCC 3 SETANT2 4 CK 5 INHIBIT 6 SGLGND 7 OUTGATE2 8 PWRGND Name and Function Gate Drive signal for Rectifier MOSFET. Anticipation (tANT1) in turning off OUTGATE1 is provided when the clock input goes to low level. The supply voltage range from 4.5V to 5.5V allows applications with logic gate threshold mosfets. UVLO feature guarantees proper start-up while it avoids undesirable driving during eventual dropping of the supply voltage. The voltage on this pin sets the anticipation (tANT1) in turning off the OUTGATE2. It is possible to choose among three different anticipation times by discrete partitioning of the supply voltage. This input provides synchronization for IC’s operations, being the transitions between the two output conditions based on a positive threshold, equal for the two slopes. A smart internal control logic mechanism using a 15MHz internal oscillator generates proper anticipation timing at the turn-off of each output. This feature allows safe turn-off of Synchronous Rectifiers avoiding any eventual shoot-through situation on secondary side at both transitions. Smart clock revelation mechanism makes these operations independent by false triggering pulses generated in light load conditions and by particular demagnetization techniques.Absolute maximum voltage rating of the pin can be exceeded limiting the current flowing into the pin to 10mA max. This input enables OUTGATE2 to work when its voltage is lower than the negative threshold voltage (VINHIBITVH the OUTGATE2 will be high for a minimum conduction time (tON(GATE2)). In typical forward converter application, it is possible to turn off the freewheeling MOSFET when the current through it tends to reverse, allowing discontinuous conduction mode and providing protection to the converter from eventual sinking current from the load.Absolute maximum voltage rating of the pin can be exceeded limiting the current flowing into the pin to 10mA max. Reference for all the control logic signals. This pin is completely separated from the PWRGND to prevent eventual disturbances to affect the control logic. Gate Drive signal for Freewheeling MOSFET. Anticipation [tANT2] in turning off OUTGATE2 is provided when the clock input goes to high level. Reference for power signals, this pin carries the full peak currents for the two outputs. 3/12 STSR2P/STSR2PM ELECTRICAL CHARACTERISTICS (VCC=5V, CK= 250kHz, VINHIBIT =-200mV, TJ =-40 to 125°C, unless otherwise specified.) Symbol Parameter Test Conditions Min. Typ. Max. 3.8 4 3.5 3.6 5.5 5.8 6 V 22 30 mA 3 5 0.10 0.16 SUPPLY INPUT AND UNDER VOLTAGE LOCK OUT VCCON Start Threshold VZ Turn OFF Threshold After Start Zener Voltage ICC Unloaded Supply Current VCCOFF CK=0V OUTGATE1,2= no load CK=0V GATE DRIVER OUTPUTS VOL Output Low Voltage VOH Output High Voltage IOUT tR Output Source Peak Current Output Sink Peak Current Output Series Source Resistance Output Series Sink Resistance OUTGATE1,2 Rise Time tF OUTGATE1,2 Fall Time tP1 tP2 ROUT OUTGATE1,2= no load IOUTGATE1,2=-200mA IOUTGATE1,2=200mA 4.70 V V V 4.85 V 2 A IOUTGATE1,2=-200mA 3.5 0.75 1.5 IOUTGATE1,2=200mA 0.5 0.8 CLOAD=5nF (Note 1) 40 ns CLOAD=5nF (Note 1) 30 ns Clock Propagation Delay to No Load Turn ON of OUTGATE1 130 ns Clock Propagation Delay to No Load Turn ON of OUTGATE2 50 ns No Load 75 ns VANT2 = 0 to 1/3VCC; no load 75 ns VANT2 = 1/3VCC to 2/3VCC; no load 150 VANT2 = 2/3VCC to VCC; no load 225 TURN-OFF ANTICIPATION TIME OUTGATE1 Turn-off tANT1 Anticipation Time OUTGATE2 Turn-off tANT2 Anticipation Time ISETANT2 IZ = 2mA Unit Leakage Current (Note 2) -0.1 0.1 Ω µA INHIBIT OUTGATE2 ENABLE VH Threshold Voltage TJ = 25°C IH Leakage Current (Note 2) VINHIBIT = 200mV -30 -25 mV -400 nA VINHIBIT = -200mV tON(GATE2) OUTGATE1 Turn-off Anticipation Time Reference Voltage VCK ICK DOFF tPW 1 VINHIBIT = 200mVNo Load 250 TJ = 25°C 2.6 LX Leakage Current Duty Cycle Shut Down TJ = 25°C for STSR2P Duty Cycle Turn ON after Shut Down Minimum Pulse Width TJ = 25°C for STSR2P STSR2PM 13 ns 2.8 V 600 µA 14 18 % 20 200 Note1: tR is measured between 10% and 90% of the final voltage; tF is measured between 90% and 10% on the initial voltage Note2: Parameter guaranteed by design 4/12 µA ns STSR2P/STSR2PM TIMING DIAGRAM APPLICATION INFORMATION: STSR2 IN FORWARD CONVERTER SECONDARY SIDE NOTES 1) Ceramic Capacitors C1 and C2 must be placed very close to the IC; 2) R1 and R2 set the anticipation time by partitioning the VCC voltage; 3) R3 and R4 is a resistor divider meant to provide the correct CK voltage range; 4) R5 limits the current flowing through diode D2 when Freewheeling drain voltage is high; 5) D1 could be necessary to protect INHIBIT pin from negative voltages. 6) D2 could be necessary to protect INHIBIT pin from voltages higher than VCC 7) D3 could be necessary to protect CK pin from voltages higher than VCC. 8) SGLGND layout trace must not include OUTGATE1,2 current paths. 9) A capacitor in parallel with R4 could be necessary to eliminate turn off voltage spike. 5/12 STSR2P/STSR2PM EXAMPLE OF COMPONENTS SELECTION FOR A FORWARD CONVERTER Forward Specification: VIN=36-72V VOUT=3.3V n=Np/Ns=4.5 R3 and R 4 are calculated assuring a minimum voltage of 2.8V at CK pin. At 36V input, the voltage on the secondary winding is 36/4.5=8V. Choosing R3=1.5KΩ, R4 results to be: V CK × R 3 2.8V × ( 1.5 kΩ ) R 4 ≥ ---------------------------------------------------------------- = 1k Ω × -------------------------------------------------------------------------- = 862 Ω 8 V – 220µA × 1.5 kΩ – 2.8V V IN – I CK ( 2.8 ) × R 3 – V CK R4=1kΩ is chosen. At 72V input the current at CK pin is calculated as: V IN ( max ) – V CC – 0.3 16 – 5 – 0.3 I CK = ----------------------------------------------------- = ------------------------------ = 7.13mA R3 1.5kΩ This value is below the maximum allowable current flowing into the CK pin (10mA). If the 10mA value is exceeded an external diode connected to VCC must be added (D3). R1 and R 2 values set the anticipation time for OUTGATE2. For R1=∞ and R2=0, tANT2=75ns; for R1=R 2=10kΩ, tANT2=150ns; for R 1=0 and R2=∞, tANT2=225ns. The RC group composed by R5 and the parasitic capacitance of Inhibit pin (typically 5pF) delays the signal on Inhibit comparator. This delay must be lower than 200ns. This condition imposes a maximum value for R5 of about 20kΩ. In general a suggested value for R5 is 10kΩ. At 72V input, the secondary voltage is 16V, so the maximum current flowing into Inhibit pin is 16V/10kΩ=1.6mA which is below the maximum allowable current for the pin (10mA). If the 10mA value is exceeded an external diode (D2) connected to VCC must be added. The maximum negative voltage of –0.6V must be guaranteed for the Inhibit pin. If this negative voltage is exceeded the current must be limited to 50mA. If necessary, a diode (D1) connected to SGLGND can be added to satisfy this specification. INHIBIT OPERATION OF OUTGATE2 IN DISCONTINUOUS CONDUCTION MODE 6/12 STSR2P/STSR2PM INHIBIT OPERATION OF OUTGATE2 NOTE: VINHIBIT =+200mV 7/12 STSR2P/STSR2PM TYPICAL PERFORMANCE CHARACTERISTICS (unless otherwise specified Tj = 25°C Figure 1 : Zener Characteristics Figure 4 : Sink-Source ON Resistance vs Temperature Figure 2 : Rise and Fall Time vs Load Capacitor Figure 5 : Clock Threshold Voltage vs Temperature Figure 3 : OUTGATE1,2 vs Characteristics Figure 6 : INHIBIT Threshold Voltage vs Temperature 8/12 STSR2P/STSR2PM Figure 7 : Supply Current vs Load Capacitor (each output) Figure 10 : Duty Cycle Shut Down vs Temperature Figure 8 : Supply Current vs Clock Frequency Figure 11 : Duty Cycle Turn ON After Shut Down vs Temperature Figure 9 : TON(GATE2) vs Temperature Figure 12 : Clock Leakage Current vs Clock Voltage 9/12 STSR2P/STSR2PM SO-8 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8˚ (max.) 0.1 0.04 0016023/C 10/12 STSR2P/STSR2PM Tape & Reel SO-8 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 22.4 0.519 0.882 Ao 8.1 8.5 0.319 0.335 Bo 5.5 5.9 0.216 0.232 Ko 2.1 2.3 0.082 0.090 Po 3.9 4.1 0.153 0.161 P 7.9 8.1 0.311 0.319 11/12 STSR2P/STSR2PM Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2003 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 12/12