STTH1602CT

STTH1602C High efficiency ultrafast diode Datasheet - production data A1 A2 Description K Dual center tap rectifier suited for switch mode power supply and high frequency DC to DC converters. K A2 K A2 K A1 A1 TO-220AB Packaged either in TO-220AB, TO-220FPAB and D2PAK, this device is especially intended for use in low voltage, high frequency inverters, free wheeling and polarity protection applications. Table 1: Device summary TO-220FPAB Symbol Value IF(AV) Up to 2 x 10 A VRRM 200 V Tj (max.) 175 °C VF (typ.) 0.78 V trr (typ.) 21 ns K K A2 A2 A1 A1 D²PAK Features        Suited for SMPS Low losses Low forward and reverse recovery time Low leakage current High junction temperature Insulated package: TO-220FPAB  insulating voltage: 2000 VRMS sine ECOPACK®2 compliant component for D²PAK on demand August 2017 DocID10180 Rev 3 This is information on a product in full production. 1/15 www.st.com Characteristics 1 STTH1602C Characteristics Table 2: Absolute ratings (limiting values, per diode, at 25 °C, unless otherwise specified) Symbol Parameter Value Unit VRRM Repetitive peak reverse voltage 200 V IF(RMS) Forward rms current 30 A TO-220AB / D²PAK IF(AV) Average forward current δ = 0.5, square wave TO-220FPAB IFSM Surge non repetitive forward current Tstg Storage temperature range Tj TC = 150 °C Per diode 8 TC = 140 °C Per device 16 TC = 140 °C Per diode 10 TC = 130 °C Per device 20 TC = 130 °C Per diode 8 TC = 100 °C Per device 16 TC = 110 °C Per diode 10 TC = 75 °C Per device 20 tp = 10 ms sinusoidal Maximum operating junction temperature A 80 A -65 to +175 °C 175 °C Value Unit Table 3: Thermal parameter Symbol Parameter Per diode 3.0 Per device 1.9 Per diode 5.5 Per device 4.5 TO-220AB / D²PAK Rth(j-c) Junction to case TO-220FPAB Rth(c) TO-220AB / D²PAK 0.8 TO-220FPAB 3.5 Coupling When the diodes 1 and 2 are used simultaneously: ΔTj(diode1) = P(diode1) x Rth(j-c) (per diode) + P(diode2) x Rth(c) 2/15 °C/W DocID10180 Rev 3 °C/W STTH1602C Characteristics Table 4: Static electrical characteristics (per diode) Symbol IR(1) Parameter Test conditions Reverse leakage current Tj = 25 °C VR = VRRM Tj = 125 °C Tj = 25 °C VF(2) Forward voltage drop IF = 8 A Tj = 150 °C Tj = 25 °C IF = 16 A Tj = 150 °C Min. Typ. - Max. 6 - 4 - 60 Unit µA 1.10 - 0.78 0.89 - 1.25 - 1.05 V Notes: (1)Pulse test: tp = 5 ms, δ < 2% (2)Pulse test: tp = 380 µs, δ < 2% To evaluate the conduction losses use the following equation: P = 0.73 x IF(AV) + 0.020 x IF2(RMS) Table 5: Dynamic electrical characteristics (per diode) Symbol trr IRM tfr Parameter Test conditions Typ. Max. Unit Reverse recovery time Tj = 25 °C IF = 1 A, VR = 30 V, dIF/dt = 100 A/µs - 21 26 ns Reverse recovery current Tj = 125 °C IF = 8 A, VR = 160 V, dIF/dt = 200 A/µs - 6.8 8.8 A IF = 8 A, dIF/dt = 100 A/µs VFR = 1.1 x VFmax - 160 ns IF = 8 A, dIF/dt = 100 A/µs - Forward recovery time Tj = 25 °C VFP Min. Forward recovery voltage DocID10180 Rev 3 2.4 V 3/15 Characteristics 1.1 STTH1602C Characteristics (curves) Figure 2: Forward voltage drop versus forward current (typical values, per diode) Figure 1: Peak current versus duty cycle (per diode) IM(A) 80 100 70 IF (A) 90 IM T 80 60 δ=tp/T 50 70 tp 60 Tj = 150 °C Tj = 25 °C 50 40 P = 15W 40 30 30 P = 8W 20 10 20 10 P = 3W 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 1.0 Figure 3: Forward voltage drop versus forward current (maximum values, per diode) 100 VF (V) 0 0.0 δ Figure 4: Relative variation of thermal impedance junction to case versus pulse duration (TO-220AB, D²PAK) IF (A) Zth(j-c) /Rth(j-c) 1.0 90 80 70 60 Single pulse Tj = 150 °C 50 Tj = 25 °C 40 30 20 10 t p(s) VF (V) 0 0.0 0.1 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 1.E-03 Figure 5: Relative variation of thermal impedance junction to case versus pulse duration (TO-220FPAB) Zth(j-c) /Rth(j-c) 1.E-02 1.E-01 1.E+00 Figure 6: Junction capacitance versus reverse voltage applied (typical values, per diode) C(pF) 100 1.0 F=1MHz VOSC=30mVRMS Tj=25°C Single pulse 0.1 VR(V) t p(s) 10 0.0 1.E-03 4/15 0 1.E-02 1.E-01 1.E+00 1.E+01 DocID10180 Rev 3 50 100 150 200 STTH1602C Characteristics Figure 7: Reverse recovery charges versus dIF/dt (typical values, per diode) 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 Q rr (nC) Figure 8: Reverse recovery time versus dIF/dt (typical values, per diode) t rr (ns) 80 IF = 8 A VR = 160 V IF = 8 A VR = 160 V 70 60 Tj = 125 °C Tj = 125 °C 50 40 Tj = 25 °C 30 Tj = 25 °C 20 10 dIF/dt (A/µs) dIF/dt (A/µs) 0 10 100 1000 10 Figure 9: Peak reverse recovery current versus dIF/dt (typical values, per diode) 16 100 1000 Figure 10: Relative variation of dynamic parameters versus junction temperature IRM (A) 1.4 IF = 8 A VR = 160 V 14 IF = 8 A VR = 160 V Reference: Tj = 125 °C 1.2 12 1.0 Tj = 125 °C 10 IRM 0.8 8 0.6 6 Qrr 0.4 Tj = 25 °C 4 0.2 2 T j (°C) dIF/dt (A/µs) 0.0 0 10 100 25 1000 50 75 100 125 Figure 11: Thermal resistance junction to ambient versus copper surface under tab R th (j-a) (°C/W ) 80 D²PAK 70 Epoxy printed board FR4, copper thickness = 35 µm 60 50 40 30 20 10 SCu(cm²) 0 0 5 10 15 20 25 DocID10180 Rev 3 30 35 40 5/15 150 Package information 2 STTH1602C Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.     6/15 Cooling method: by conduction (C) Epoxy meets UL94,V0 Recommended torque value (TO-220AB and TO-220FPAB): 0.55 N.m Maximum torque value (TO-220AB and TO-220FPAB): 0.70 N.m DocID10180 Rev 3 STTH1602C 2.1 Package information D²PAK package information Figure 12: D²PAK package outline This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID10180 Rev 3 7/15 Package information STTH1602C Table 6: D²PAK package mechanical data Dimensions Ref. Millimeters Min. Max. Min. Max. A 4.36 4.60 0.172 0.181 A1 0.00 0.25 0.000 0.010 b 0.70 0.93 0.028 0.037 b2 1.14 1.70 0.045 0.067 c 0.38 0.69 0.015 0.027 c2 1.19 1.36 0.047 0.053 D 8.60 9.35 0.339 0.368 D1 6.90 8.00 0.272 0.311 D2 1.10 1.50 0.043 0.060 E 10.00 10.55 0.394 0.415 E1 8.10 8.90 0.319 0.346 E2 6.85 7.25 0.266 0.282 e 2.54 typ. 0.100 e1 4.88 5.28 0.190 0.205 H 15.00 15.85 0.591 0.624 J1 2.49 2.90 0.097 0.112 L 1.90 2.79 0.075 0.110 L1 1.27 1.65 0.049 0.065 L2 1.30 1.78 0.050 0.070 R V2 8/15 Inches 0.4 typ. 0° 0.015 8° DocID10180 Rev 3 0° 8° STTH1602C Package information Figure 13: D²PAK recommended footprint (dimensions in mm) DocID10180 Rev 3 9/15 Package information 2.2 STTH1602C TO-220AB package information Figure 14: TO-220AB package outline 10/15 DocID10180 Rev 3 STTH1602C Package information Table 7: TO-220AB package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Max. Min. Max. A 4.40 4.60 0.1732 0.1811 b 0.61 0.88 0.0240 0.0346 b1 1.14 1.70 0.0449 0.0669 c 0.48 0.70 0.0189 0.0276 D 15.25 15.75 0.6004 0.6201 D1 1.27 typ. 0.0500 typ. E 10.00 10.40 0.3937 0.4094 e 2.40 2.70 0.0945 0.1063 e1 4.95 5.15 0.1949 0.2028 F 1.23 1.32 0.0484 0.0520 H1 6.20 6.60 0.2441 0.2598 J1 2.40 2.72 0.0945 0.1071 L 13.00 14.00 0.5118 0.5512 L1 3.50 3.93 0.1378 0.1547 L20 16.40 typ. 0.6457 typ. L30 28.90 typ. 1.1378 typ. ØP 3.75 3.85 0.1476 0.1516 Q 2.65 2.95 0.1043 0.1161 Notes: (1)Inch dimensions are for reference only. DocID10180 Rev 3 11/15 Package information 2.3 STTH1602C TO-220FPAB package information Figure 15: TO-220FPAB package outline 12/15 DocID10180 Rev 3 STTH1602C Package information Table 8: TO-220FPAB package mechanical data Dimensions Ref. Millimeters Inches (for reference only) Min. Max. Min. Max. A 4.40 4.60 0.1739 0.1818 B 2.5 2.7 0.0988 0.1067 D 2.50 2.75 0.0988 0.1087 E 0.45 0.70 0.0178 0.0277 F 0.75 1.0 0.0296 0.0395 F1 1.15 1.70 0.0455 0.0672 F2 1.15 1.70 0.0455 0.0672 G 4.95 5.20 0.1957 0.2055 G1 2.40 2.70 0.0949 0.1067 H 10.00 10.40 0.3953 0.4111 L2 16.00 typ. 0.6324 typ. L3 28.60 30.60 1.1304 1.2095 L4 9.80 10.6 0.3874 0.4190 L5 2.90 3.60 0.1146 0.1423 L6 15.90 16.40 0.6285 0.6482 L7 9.00 9.30 0.3557 0.3676 Dia 3.0 3.20 0.1186 0.1265 DocID10180 Rev 3 13/15 Ordering information 3 STTH1602C Ordering information Table 9: Ordering information 4 Order code Marking Package Weight Base qty. Delivery mode STTH1602CG-TR STTH1602CG D2PAK 1.38 g 1000 Tape and reel STTH1602CT STTH1602CT TO-220AB 1.90 g 50 Tube STTH1602CFP STTH1602CFP TO-220FPAB 1.70 g 50 Tube Revision history Table 10: Document revision history Date Revision Feb-2004 1 First release 2 Updated ECOPACK statement. Reformatted to current standards. Updated Section 2: Package mechanical data 3 Updated features, package silhouette and Table 1: "Device summary". Updated Section 1: "Characteristics", Section 2: "Package information" and Section 3: "Ordering information". 23-Apr-2014 11-Aug-2017 14/15 Changes DocID10180 Rev 3 STTH1602C IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2017 STMicroelectronics – All rights reserved DocID10180 Rev 3 15/15