STTH80S06W

STTH80S06 Turbo 2 ultrafast high voltage rectifier Datasheet - production data Description $ . The STTH80S06, which is using ST Turbo 2 600 V technology, is specially suited for use in switching power supplies, and solar inverters. Thanks to its low VF characteristics, as well as fast recovery, this device exhibits high performance in free-wheeling applications or boost converters working at switching frequency up to 100 kHz. $ . Table 1. Device summary '2 Features • Ultrafast switching • Low reverse current Symbol Value IF(AV) 80 A VRRM 600 V Tj (max) 175 °C VF (typ) 1.65 V trr (typ) 32 ns • Low thermal resistance • Reduces switching and conduction losses • Repetitive peak reverse voltage specified from -40 °C to +175 °C July 2015 This is information on a product in full production. DocID028111 Rev 1 1/8 www.st.com Characteristics 1 STTH80S06 Characteristics Table 2. Absolute ratings (limiting values at Tj = 25 °C, unless otherwise specified) Symbol Parameter VRRM Repetitive peak reverse voltage IF(RMS) RMS forward current Value Unit 600 V 113 A Tj = -40 °C to +175 °C IF(AV) Average forward current, δ = 0.5 square wave Tc = 105 °C 80 A IFSM Surge non repetitive forward current tp = 10 ms sinusoidal 400 A Tstg Storage temperature range -65 to +175 °C Operating junction temperature range -40 to +175 °C Value Unit 0.3 °C/W Tj Table 3. Thermal parameters Symbol Rth(j-c) Parameter Junction to case Table 4. Static electrical characteristics Symbol IR(1) Parameter Reverse leakage current Test conditions Tj = 25 °C Tj = 150 °C Tj = 25 °C VF(2) Forward voltage drop Tj = 150 °C Tj = 150 °C Min. Typ. Max. Unit - 0.2 50 µA - 0.2 2 mA - 1.7 2.2 VR = VRRM IF = 20 A IF = 80 A - 1.0 1.3 - 1.65 2.15 V 1. Pulse test: tp = 5 ms, δ < 2% 2. Pulse test: tp = 380 µs, δ < 2% To evaluate the conduction losses use the following equation: P = 1.43 x IF(AV) + 0.009 x IF2(RMS) Table 5. Dynamic electrical characteristics Symbol trr IRM Sfactor Reverse recovery time Test conditions Tj = 25 °C Reverse recovery current Softness factor Q rr Reverse recovery charges tfr Forward recovery time VFP 2/8 Parameter Forward recovery voltage Tj = 125 °C Tj = 25 °C Min. Typ. Max. Unit IF = 0.5 A, Irr = 0.25 A, IR = 1 A - 32 45 ns IF = 1 A, VR = 30 V, dIF/dt = -50 A/µs - 55 75 ns - 110 - ns - 14 - A - 0.4 - - - 900 - nC - - 800 ns - 3.6 - V IF = 80 A, dIF/dt = -200 A/µs, VR = 400 V IF = 80 A, dIF/dt = 200 A/µs, VFR = 1.1 x VFmax DocID028111 Rev 1 STTH80S06 Characteristics Figure 1. Average forward power dissipation versus average forward current  3)$9 : Figure 2. Forward voltage drop versus forward current (typical values)  į  į   7  ƒ& M  į   ,)$ į  į    7  ƒ& M    7  į WS7 , WS )$9            $ 9 9    Figure 3. Forward voltage drop versus forward current (maximum values) ,)$  )         Figure 4. Relative variation of thermal impedance junction to case versus pulse duration  = 5  WKMF WKMF '2   7  ƒ& M      6LQJOHSXOVH  7  ƒ& M      9 9 )             Figure 5. Peak reverse recovery current versus dIF/dt (typical values)   ( ( ( ( Figure 6. Reverse recovery time versus dIF/dt (typical values) ,50$  95 9 7M ƒ& W V 3  ( WUUQV 95 9 7M ƒ& ,) ,)$9   ,) ;,)$9  ,) ,)$9   ,) ;,)$9  ,) ;,)$9    ,) ;,)$9 GO)GW$—V GO)GW$—V               DocID028111 Rev 1           3/8 8 Characteristics STTH80S06 Figure 7. Reverse recovery charges versus dIF/dt (typical values)  4UUQ&  95 9 7M ƒ&  Figure 8. Softness factor versus dIF/dt (typical values) 6IDFWRU 95 9 7  ƒ& ,) ,)$9 M      ,) ;,)$9   ,) ;,)$9   GO)GW$—V             Figure 9. Relative variations of dynamic parameters versus junction temperature   ,) ,)$9 95 9 5HIHUHQFH7  ƒ& 6IDFWRU           Figure 10. Transient peak forward voltage versus dIF/dt (typical values)   GO)GW$—V  9)39 ,) ,)$9 7M ƒ&  M      ,50   4UU   GO)GW$—V 7Mƒ&             Figure 11. Forward recovery time versus dIF/dt Figure 12. Junction capacitance versus reverse (typical values) voltage applied (typical values)  WIUQV  ,) ,)$9 9)5 [9)PD[ 7M ƒ&  &S) ) 0+] 9  P9 26& 506 7M ƒ&      GO)GW$—V   4/8      9 9  5   DocID028111 Rev 1    STTH80S06 2 Package information Package information • Epoxy meets UL94, V0 • Recommended torque value: 0.55 N·m • Maximum torque value: 1.0 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 DO-247 package information Figure 13. DO-247 package outline V Dia V A H L5 L L2 L4 F2 L3 L1 F3 D V2 F G DocID028111 Rev 1 M E 5/8 8 Package information STTH80S06 Table 6. DO-247 package mechanical data Dimensions Ref. Millimeters Min. Max. Min. Typ. Max. A 4.85 5.15 0.191 0.203 D 2.20 2.60 0.086 0.102 E 0.40 0.80 0.015 0.031 F 1.00 1.40 0.039 0.055 F2 F3 2.00 2.00 G 0.078 2.40 0.078 10.90 0.094 0.429 H 15.45 15.75 0.608 0.620 L 19.85 20.15 0.781 0.793 L1 3.70 4.30 0.145 0.169 L2 L3 18.50 14.20 0.728 14.80 0.559 0.582 L4 34.60 1.362 L5 5.50 0.216 M 2.00 3.00 0.078 0.118 V 5° 5° V2 60° 60° Dia. 6/8 Typ. Inches 3.55 3.65 DocID028111 Rev 1 0.139 0.143 STTH80S06 3 Ordering information Ordering information Table 7. Ordering information 4 Order code Marking Package Weight Base qty Delivery mode STTH80S06W STTH80S06W DO-247 4.40 g 30 Tube Revision history Table 8. Document revision history Date Revision 22-Jul-2015 1 Changes First issue. DocID028111 Rev 1 7/8 8 STTH80S06 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved 8/8 DocID028111 Rev 1