STW81200TR

STW81200 Wideband RF PLL fractional/integer frequency synthesizer with integrated VCOs and LDOs Datasheet - production data • Low power functional mode • Supply voltage: 3.0 V to 5.4 V • Small size exposed pad VFQFPN36 package 6 x 6 x 1.0 mm VFQFPN36 • Process: BICMOS 0.25 µm SiGe Features Applications • Output frequency range: 46.875 to 6000 MHz • Cellular/4G infrastructure equipment • Very low noise – Normalized in band phase noise floor: -227 dBc/Hz – VCO phase noise: -135 dBc/Hz @ 1 MHz offset, 4.0 GHz carrier – Noise floor: -160 dBc/Hz • Instrumentation and test equipment • Dual architecture frequency synthesizer: Fractional-N and Integer-N • Integrated VCOs with automatic center frequency calibration • Dual RF Output broadband matched with programmable power level and mute function • External VCO option with 5 V charge pump • Integrated low noise LDO voltage regulators • Maximum phase detector frequency: 100 MHz • Exact frequency mode • Fast lock and cycle slip reduction • Differential reference clock input (LVDS and LVECPL compliant) supporting up to 800 MHz • 13-bit programmable reference frequency divider • Programmable charge pump current • Digital lock detector • Integrated reference crystal oscillator core • Logic compatibility/tolerance 1.8 V/3.3 V August 2019 • Other wireless communication systems Table 1. Device summary Order Code Package Packing STW81200T VFQFPN36 Tray STW81200TR VFQFPN36 Tape and reel Description • Programmable RF output dividers by 1/2/4/8/16/32/64 • R/W SPI interface • Cable TV The STW81200 is a dual architecture frequency synthesizer (Fractional-N and Integer-N), that features three low phase-noise VCOs with a fundamental frequency range of 3.0 GHz to 6.0 GHz and a programmable dual RF output divider stage which allows coverage from 46.875 MHz to 6 GHz. The STW81200 optimizes size and cost of the final application thanks to the integration of lownoise LDO voltage regulators and internallymatched broadband RF outputs. The STW81200 is compatible with a wide range of supply voltages (from 3.0 V to 5.4 V) providing to the end user a very high level of flexibility which trades off excellent performance with power dissipation requirements. A low-power functional mode (software controlled) gives an extra power saving. Additional features include crystal oscillator core, external VCO mode and output-mute function. DS10185 Rev 8 1/61 www.st.com Contents STW81200 Contents 1 Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7 Circuit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.1 Reference input stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.2 Reference divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.3 PLL N divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7.3.1 2/61 Fractional spurs and compensation mechanism . . . . . . . . . . . . . . . . . . 26 7.4 Phase frequency detector (PFD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7.5 Lock detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7.6 Charge pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7.7 Fast lock mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.8 Cycle slip reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.9 Voltage controlled oscillators (VCOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7.10 RF output divider stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 7.11 Low-power functional modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 7.12 LDO voltage regulators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 7.13 STW81200 register programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.14 STW81200 register summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 7.15 STW81200 register descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.16 Power ON sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 7.17 Example of register programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 DS10185 Rev 8 STW81200 8 Contents Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 8.1 Application diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 8.2 Thermal PCB design considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 9 Evaluation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 10 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 10.1 11 VFQFPN36 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 DS10185 Rev 8 3/61 3 List of figures STW81200 List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. 4/61 Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Top view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 VCO open-loop phase noise (5 V supply) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Closed-loop phase noise at 4.8 GHz, divided by 1 to 64 (5 V supply) . . . . . . . . . . . . . . . . 19 VCO open-loop phase noise at 4.4 GHz vs. supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 VCO open-loop phase noise over frequency vs. supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Single sideband integrated phase noise vs. frequency and supply (FPFD= 50 MHz) . . . . . 20 Figure of merit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Phase noise and fractional spurs at 2646.96 MHz vs. supply (FPFD = 61.44 MHz) . . . . . 20 Phase noise and fractional spurs at 2118.24 MHz vs. supply (FPFD = 61.44 MHz) . . . . . 20 Phase noise and fractional spurs at 2118.24 MHz at 5.0 V supply (FPFD = 61.44 MHz) . 20 Phase noise and fractional spurs at 2118.24 MHz at 3.6 V supply (FPFD = 61.44 MHz) . 20 Phase noise and fractional spurs at 2118.24 MHz at 3.0 V supply (FPFD = 61.44 MHz) . 21 Phase noise at 5.625 GHz and 4.6 GHz (FPFD = 50 MHz) . . . . . . . . . . . . . . . . . . . . . . . . 21 Typical VCO control voltage after VCO calibration (3.6 V supply) . . . . . . . . . . . . . . . . . . . 21 Average KVCO over VCO frequency and supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Output power level vs. temperature - single ended (RF_OUT_PWR=7) . . . . . . . . . . . . . . 21 Output power level – single ended (3 dB more for differential). . . . . . . . . . . . . . . . . . . . . . 21 Typical spur level at PFD offset over carrier frequency (5.0 V supply) . . . . . . . . . . . . . . . . 22 Typical spur level vs. offset from 4.5 GHz (5.0 V supply, FPFD=50MHz) . . . . . . . . . . . . . . 22 10 kHz fractional spur (integer boundary) vs. temperature (5.0 V supply, FPFD = 50 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 800 kHz fractional spur (integer boundary) vs. temperature (5.0 V supply, FPFD = 50 MHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Frequency settling with VCO calibration – wideband view . . . . . . . . . . . . . . . . . . . . . . . . . 22 Frequency settling with VCO calibration – narrowband view . . . . . . . . . . . . . . . . . . . . . . . 22 Overall current consumption vs. temperature (5.0 V supply, FPFD = 50 MHz) . . . . . . . . . . 23 Current consumption – standard vs. low power (5.0 V supply, FPFD = 50 MHz) . . . . . . . . 23 Current consumption – standard vs. low power (3.6 V supply, FPFD = 50 MHz) . . . . . . . . 23 Current consumption – standard vs. low power (3.0 V supply, FPFD = 50 MHz) . . . . . . . . 23 Reference clock buffer configurations: single-ended (A), differential (B), crystal mode (C) 24 PFD diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 SPI Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 SPI timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Application diagram (internal VCO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Application diagram (external VCO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 VFQFPN - 36 pin, 6x6 mm, 0.5 mm pitch very thin profile fine pitch quad flat package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 VFQFPN - 36 pin, 6x6 mm, 0.5 mm pitch very thin profile fine pitch quad flat package recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 DS10185 Rev 8 STW81200 List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Digital logic levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Electrical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Phase noise specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Current value vs. selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Blocks with programmable current and related performance . . . . . . . . . . . . . . . . . . . . . . . 31 SPI timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SPI Register map (address 12 to 15 not available) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 STW81200 order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 VFQFPN - 36 pin, 6x6 mm, 0.5 mm pitch very thin profile fine pitch quad flat package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 DS10185 Rev 8 5/61 5 Functional block diagram 1 STW81200 Functional block diagram Figure 1. Functional block diagram 9,1B/'2B5)B',* 5)B2873 (;79&2B,13 (;79&2B,11 9,1B/'2B9&2 &%11.93 MHz With reference clock frequency in the range 10 MHz to 11.93 MHz, due to the limits of N value in fractional mode, the full VCO frequencies would not be addressed in fractional mode; in this case the frequency doubler in the reference path can be enabled. 2. Reference clock signal @ 100 MHz, R=2 3. The minimum frequency step is obtained as FPFD / (2^21); these typical values are obtained considering FPFD = 100 MHz. 4. PFD frequency leakage. 5. This is the level inside the PLL loop bandwidth due to the contribution of the ΔΣ Modulator. In order to obtain the fractional spurs level for a specific frequency offset, the attenuation provided by the loop filter at such offset should be subtracted. 6. Once a VCO is programmed at the initial temperature T0 inside the operating temperature range (-40 °C to +85 °C), the synthesizer is able to maintain the lock status only if the temperature drift (in either direction) is within the limit specified by ΔTLK, provided that the final temperature Tf is still inside the nominal range. 7. In order to guarantee the performance of ΔTLK the bit CAL_TEMP_COMP in register ST6 must be set to ‘1’. 8. Current consumption measured with PLL locked in following conditions: Reference clock signal @ 100 MHz; PFD @50 MHz (R=2); VCO @ 4005 MHz 16/61 DS10185 Rev 8 STW81200 Electrical specifications Table 7. Phase noise specifications Parameter Min Typ Max - -227 - dBc/Hz Phase Noise @ 1 kHz - -64 - dBc/Hz Phase Noise @ 10 kHz - -91 - dBc/Hz Phase Noise @ 100 kHz - -114 - dBc/Hz Phase Noise @ 1 MHz - -135 - dBc/Hz Phase Noise @ 10 MHz - -154 - dBc/Hz - -160 - dBc/Hz Normalized In-Band Phase Noise(1) Floor(2) Units VCO Open Loop Phase Noise(1) at FOUT @ 4 GHz – VIN=5.0 V, VREG=4.5 V Phase Noise @ 100 MHz (1) VCO Open Loop Phase Noise at FOUT @ 4 GHz/2 = 2GHz – VIN=5.0 V, VREG=4.5 V Phase Noise @ 1 kHz - -70 - dBc/Hz Phase Noise @ 10 kHz - -97 - dBc/Hz Phase Noise @ 100 kHz - -120 - dBc/Hz Phase Noise @ 1 MHz - -141 - dBc/Hz Phase Noise @ 10 MHz - -156 - dBc/Hz Phase Noise @ 40 MHz - -159 - dBc/Hz VCO Open Loop Phase Noise(1) at FOUT @ 4 GHz/4 = 1 GHz – VIN=5.0 V, VREG=4.5 V Phase Noise @ 1 kHz - -76 - dBc/Hz Phase Noise @ 10 kHz - -103 - dBc/Hz Phase Noise @ 100 kHz - -126 - dBc/Hz Phase Noise @ 1 MHz - -146 - dBc/Hz Phase Noise @ 10 MHz - -159 - dBc/Hz Phase Noise Floor - -160 - dBc/Hz VCO Open Loop Phase Noise(1) at FOUT @ 4 GHz/32 = 125 MHz – VIN=5.0 V, VREG=4.5 V Phase Noise @ 1 kHz - -92 - dBc/Hz Phase Noise @ 10 kHz - -121 - dBc/Hz Phase Noise @ 100 kHz - -144 - dBc/Hz Phase Noise @ 1 MHz - -161 - dBc/Hz Phase Noise @ 10 MHz - -163 - dBc/Hz Phase Noise Floor - -164 - dBc/Hz DS10185 Rev 8 17/61 60 Electrical specifications STW81200 Table 7. Phase noise specifications Parameter Min Typ Max Units VCO Open Loop Phase Noise(1) at FOUT @ 4 GHz – VIN=3.6V , VREG=3.3 V Phase Noise @ 1 kHz - -62 - dBc/Hz Phase Noise @ 10 kHz - -89 - dBc/Hz Phase Noise @ 100 kHz - -113.2 - dBc/Hz Phase Noise @ 1 MHz - -133.6 - dBc/Hz Phase Noise @ 10 MHz - -152.4 - dBc/Hz Phase Noise @ 100 MHz - -158.5 - dBc/Hz Phase Noise @ 1 kHz - -60.5 - dBc/Hz Phase Noise @ 10 kHz - -88 - dBc/Hz Phase Noise @ 100 kHz - -110.3 - dBc/Hz Phase Noise @ 1 MHz - -131 - dBc/Hz Phase Noise @ 10 MHz - -150 - dBc/Hz Phase Noise @ 100 MHz - -157 - dBc/Hz VCO Open Loop Phase Noise(1) at FOUT @ 4 GHz – VIN=3.0 V, VREG=2.6 V 1. Phase Noise SSB unless otherwise specified. The VCO Open loop figures are specified at 4.5/5 V on VCC_VCO_Core (pin #3). 2. Normalized PN = Measured PN – 20log(N) – 10log(FPFD) where N is the VCO divider ratio and FPFD is the comparison frequency at the PFD input. 18/61 DS10185 Rev 8 STW81200 6 Typical performance characteristics Typical performance characteristics Figure 3. VCO open-loop phase noise (5 V supply) Figure 4. Closed-loop phase noise at 4.8 GHz, divided by 1 to 64 (5 V supply) Figure 5. VCO open-loop phase noise at 4.4 GHz vs. supply Figure 6. VCO open-loop phase noise over frequency vs. supply DS10185 Rev 8 19/61 60 Typical performance characteristics STW81200 Figure 7. Single sideband integrated phase noise vs. frequency and supply (FPFD= 50 MHz) Figure 8. Figure of merit Figure 9. Phase noise and fractional spurs at 2646.96 MHz vs. supply (FPFD = 61.44 MHz) Figure 10. Phase noise and fractional spurs at 2118.24 MHz vs. supply (FPFD = 61.44 MHz) Figure 11. Phase noise and fractional spurs at Figure 12. Phase noise and fractional spurs at 2118.24 MHz at 5.0 V supply (FPFD = 61.44 MHz) 2118.24 MHz at 3.6 V supply (FPFD = 61.44 MHz) 20/61 DS10185 Rev 8 STW81200 Typical performance characteristics Figure 13. Phase noise and fractional spurs at 2118.24 MHz at 3.0 V supply (FPFD = 61.44 MHz) Figure 14. Phase noise at 5.625 GHz and 4.6 GHz (FPFD = 50 MHz) Figure 15. Typical VCO control voltage after VCO calibration (3.6 V supply) Figure 16. Average KVCO over VCO frequency and supply Figure 17. Output power level vs. temperature single ended (RF_OUT_PWR=7) Figure 18. Output power level – single ended (3 dB more for differential) DS10185 Rev 8 21/61 60 Typical performance characteristics STW81200 Figure 19. Typical spur level at PFD offset over carrier frequency (5.0 V supply) Figure 20. Typical spur level vs. offset from 4.5 GHz (5.0 V supply, FPFD=50MHz) Figure 21. 10 kHz fractional spur (integer boundary) vs. temperature (5.0 V supply, FPFD = 50 MHz) Figure 22. 800 kHz fractional spur (integer boundary) vs. temperature (5.0 V supply, FPFD = 50 MHz) Figure 23. Frequency settling with VCO calibration – wideband view Figure 24. Frequency settling with VCO calibration – narrowband view 22/61 DS10185 Rev 8 STW81200 Typical performance characteristics Figure 25. Overall current consumption vs. temperature (5.0 V supply, FPFD = 50 MHz) Figure 26. Current consumption – standard vs. low power (5.0 V supply, FPFD = 50 MHz) Figure 27. Current consumption – standard vs. Figure 28. Current consumption – standard vs. low power (3.6 V supply, FPFD = 50 MHz) low power (3.0 V supply, FPFD = 50 MHz) DS10185 Rev 8 23/61 60 Circuit description STW81200 7 Circuit description 7.1 Reference input stage The reference input stage provides different modes for the reference clock signal. Both single-ended and differential modes (LVDS, LVECPL) are supported; a crystal mode is also provided in order to build a Pierce type crystal oscillator. Figure 29 shows the connections required for the different configurations supported. In single-ended and differential modes the inputs must be AC coupled as the REF_CLKP and REF_CLKN pins are internally biased to an optimal DC operating point. The input resistance is 100 ohms differential and the best performance for phase noise is obtained for signals with a higher slew rate, such as a square wave. Figure 29. Reference clock buffer configurations: single-ended (A), differential (B), crystal mode (C) REF_CLKP REF_CLKP REF_CLKP 100 Ω REF_CLKN REF_CLKN REF_CLKN A) 7.2 B) C) Reference divider The 13-bit programmable reference counter is used to divide the input reference frequency to the desired PFD frequency. The division ratio is programmable from 1 to 8191. The maximum allowed input frequency of the R-Counter is 200 MHz. The reference clock can be extended up to 400 MHz enabling the divide-by-2 stage or up to 800 MHz enabling the divide-by-4 stage. A frequency doubler is provided in order to double low reference frequencies and increase the PFD operating frequency thus allowing an easier filtering of the out-of-band noise of the Delta-Sigma Modulator; the doubler is introducing a noise degradation in the in-band PLL noise thus this feature should be carefully used. When the doubler is enabled, the maximum reference frequency is limited to 25 MHz. 24/61 DS10185 Rev 8 STW81200 7.3 Circuit description PLL N divider The N divider sets the division ratio in the PLL feedback path. Both Integer-N and Fractional-N PLL architectures are implemented in order to ensure the best overall performance of the synthesizer. The Fractional-N division is achieved combining the integer divider section with a DeltaSigma modulator (DSM) which sets the fractional part of the overall division ratio. The DSM is implemented as a MASH structure with programmable order (2 bit; 1st, 2nd, 3rd and 4th order), programmable MODULUS (21 bit). It includes also a DITHERING function (1 bit) which can be used to reduce fractional spur tones by spreading the DSM sequence and consequently the energy of the spurs over a wider bandwidth. The overall division ratio N is given by: N = N INT + N FRAC The integer part NINT is 17-bit programmable and can range from 24 to 131071 in Integer Mode. For NINT ≥ 512 the fractional mode is not allowed and the setting used for DSM does not have any effect. Based upon the selected order of the Delta-Sigma Modulator the allowed range of NINT values changes as follows: • 24 to 510 - 1st Order DSM • 25 to 509 - 2nd Order DSM • 27 to 507 - 3rd Order DSM • 31 to 503 - 4th Order DSM The fractional part NFRAC of the division ratio is controlled by setting the values FRAC and MOD (21 bits each) and it depends also on the value of DITHERING (1 bit): FRAC DITHERING N FRAC = ----------------- + ----------------------------------MOD 2 ⋅ MOD The MOD value can range from 2 to 2097151, while the range of FRAC is from 0 to MOD-1. If the DITHERING function is not used (DITHERING=0) the fractional part of N is simply achieved as ratio of FRAC over MOD. DS10185 Rev 8 25/61 60 Circuit description STW81200 The resulting VCO frequency is: F ref F ref FRAC DITHERING F VCO = ---------- ⋅ N = ---------- ⋅ ⎛ N INT + ----------------- + -----------------------------------⎞ ⎝ R R MOD 2 ⋅ MOD ⎠ where: FVCO is the output frequency of VCO Fref is the input reference frequency R is the division ratio of reference chain N is the overall division ratio of the PLL The implementation with programmable modulus allows the user to select easily the desired fraction and the exact synthesized frequency without any approximation. The MOD value can be set to very high values thus the frequency resolution of the synthesizer can reach very fine steps (down to a few hertz). A ‘low spur mode’ could be configured by maximizing both FRAC and MOD values, keeping the same desired FRAC/MOD ratio, and setting the DITHERING bit to ‘1’. The drawback is a small frequency error, equal to FPFD/(2*MOD), on the synthesized frequency which is in the range of a few hertz, usually tolerated by most applications. 7.3.1 Fractional spurs and compensation mechanism The fractional PLL operation generates unwanted fractional spurs around the synthesized frequency. The integer boundary spurs occur when the carrier frequency is close to an integer multiple of the PFD frequency. If the frequency difference between the carrier and the N*FPFD falls inside the PLL loop bandwidth, the integer boundary spur is unfiltered and represents the worst case situation giving the highest spur level. The channel spurs are generated by the delta-sigma modulator operations and depend on its settings (they are mainly related to the MOD value). The channel spurs appear at a frequency offset from the carrier, equal to FPFD/MOD and its harmonics, and they are not integer boundary. If the MOD value is extremely high (close to the maximum value of 221-1) the channel spur offset is of the order of a tenth of a Hertz and it appears as ‘granular noise’ shaped by the PLL around the carrier. The STW81200 provides the user with three different mechanisms to compensate fractional spurs: PFD delay mode, charge pump leakage current and down-split current. These features should be adopted case-by-case as they give different results spur-level results depending on setup conditions (reference clock frequency, PFD frequency, DSM setup, VCO frequency, carrier frequency, charge pump current, VCO/charge pump supply voltage). 26/61 DS10185 Rev 8 STW81200 Circuit description PFD delay mode The STW81200 implements two programmable differentiated delay lines in the reset path of the main flip-flop of the PFD. This allow different delay reset values to be set for VCO divided path and reference-clock divided path, allowing an offset value to be forced on the PFD and charge-pump characteristics, far enough from the zero in order to guarantee that the whole circuit works in a more linear region. It is possible to set the sign of the delay through the PFD_DEL_MODE bit in the ST3 Register (no delay, VCO_DIV_delayed or REF_DIV_delayed). The delay value can be set through the PFD_DEL bit in the ST0 Register (2 bit; 0=1.2 ns, 1=1.9 ns, 2=2.5 ns, 3=3.0 ns). Even though the for spur-compensation settings are best optimized case-bycase, the setup ‘VCO_DIV_delayed + 1.2 ns delay’ is strongly recommended for most conditions. Charge pump leakage current A different way to force an offset value on the PFD+CP characteristics is provided within the STW81200 by sourcing or sinking a DC leakage current from the charge pump (settings available in the ST3 Register). The leakage current is 5-bit programmable starting from a base DC current of 10 µA (it can be doubled to 20 uA by setting bit CP_LEAK_x2 = 1b). The sign is set by CP_LEAK_DIR bit: 0b = down-leakage (sink), 1b = up-leakage (source). The resulting delay offset can be calculated as follows: I LEAK delay = ----------------------------F PFD ⋅ I CP Experimental results show that down-leakage currents are more effective than up-leakage. The user must be aware that the use of the leakage current mechanism might impact the overall phase noise performance by increasing the charge pump noise contribution. Down-split current This mechanism is enabled through the DNSPLIT_EN bit (ST3 Register), is the injection of a down-split current pulse from the charge pump circuit. The current pulse is 16 VCO cycles wide while the current level is set by the PFD_DEL bit (ST0 Register) among 4 different possible values: 0, 0.25*ICP, 0.5*ICP or 0.75*ICP. 7.4 Phase frequency detector (PFD) The PFD takes inputs from the reference and the VCO dividers and produces an output proportional to the phase error. The PFD includes a delay gate that controls the width of the anti-backlash pulse (1.2 to 3 ns). This pulse ensures that there is no dead zone in the PFD transfer function. Figure 30 shows a simplified schematic of the PFD. DS10185 Rev 8 27/61 60 Circuit description STW81200 Figure 30. PFD diagram VDD Up DFF Fref R Delay Fref VDD R DFF Down ABL 7.5 Lock detect The lock detector indicates the lock state for the PLL. The lock condition is detected by comparing the UP and DOWN outputs of the digital Phase Frequency Detector A CMOS logic output signal indicates the lock state; the polarity of the output signal can be inverted using the LD_ACTIVELOW bit. The lock condition occurs when the delay between the edges of UP and DOWN signals is lower than a specific value (3-bit programmable from 2 ns to 16 ns) and this condition is stable for a specific number of consecutive PFD cycles (3-bit programmable counter from 4 to 4096 cycles). This flexibility is needed by the lock detector circuitry to work properly with all the possible different PLL setups (Integer-N, Fractional-N, different PFD frequencies and so on). 7.6 Charge pump This block drives two matched current sources, Iup and Idown, which are controlled respectively by the UP and DOWN PFD outputs. The nominal value of the output current (ICP) can be set by a 5-bit word. The minimum value of the output current (ICP) is 158 µA. The charge pump also includes a compensation circuit to take into account the KVCO variation versus VCO control voltage, which changes with temperature and process for a specified frequency. The KVCO compensation block adjusts the nominal ICP value, minimizing the variation of the product ICP x KVCO to keep the PLL bandwidth constant for the specified frequency. In order to compensate the change of KVCO over frequency, the user should manually adjust the ICP value to keep the PLL bandwidth constant. In addition, the charge-pump output stage can operate with a 2.5 V to 5.0 V supply voltage. The LDO_4V5 regulator, programmable at 2.6 V, 3.3 V and 4.5 V, can be used for this purpose. The CP_SUPPLY_MODE[1:0] field (ST4 Register) must be set according to the supply voltage. 28/61 DS10185 Rev 8 STW81200 Circuit description Table 8. Current value vs. selection 7.7 CPSEL4 CPSEL3 CPSEL2 CPSEL1 CPSEL0 Current Value 0 0 0 0 0 - 0 0 0 0 1 IMIN 158 µA 0 0 0 1 0 2*IMIN 316 µA - - - - - - - - - - - - - - 1 1 1 0 1 29*IMIN 4.58 mA 1 1 1 1 0 30*IMIN 4.74 mA 1 1 1 1 1 31*IMIN 4.9 mA 0 Fast lock mode The fast-lock feature can be enabled to trade fast settling time with spurs rejection, performances which generally require different settings of PLL bandwidth (narrow for better spurs rejection and wide for fast settling time). A narrow bandwidth for lower spurs can be designed for the lock state while a wider bandwidth can be designed for the PLL transients. The wider bandwidth is achieved during the transient by increasing the charge pump current and reducing accordingly the dumping resistor value of the loop filter in order to keep the phase margin of the PLL constant. The duration of the PLL wide band mode, in terms of number of PFD cycles, is set by programming the fast lock 13 bit counter. 7.8 Cycle slip reduction The use of high FPFD/PLL_BW ratios may lead to an increased settling time due to cycle slips. A cycle slip compensation circuit is provided which automatically increases the charge pump current for high frequency errors and restores the programmed value at the end of the locking phase. 7.9 Voltage controlled oscillators (VCOs) The STW81200 VCO section consists of three separate low-noise VCOs with different LC Tanks structures to cover a wide band from 3000 MHz to 6000 MHz. Each VCO is implemented using a structure with multiple sub-bands to keep low the VCO sensitivity (Kvco), thus resulting in low phase noise and spurs performances. The correct VCO and sub-band selection is automatically performed by dedicated digital circuitry (clocked by the PFD) at every new frequency programming. The VCO calibration starts when the ST0 Register is written. DS10185 Rev 8 29/61 60 Circuit description STW81200 During the selection procedure the VCTRL of the VCO is charged to a fixed reference voltage. A stable reference clock signal to the device must be present before the VCO calibration begins. The procedure for the VCO and sub-band selection takes approximately 11 CALBCLK cycles. The calibrator clock frequency is linked to the PFD frequency (CALBCLK = FPFD/CALDIV) and should be adjusted in order to achieve correct operation. The maximum allowed frequency is 250 kHz, therefore the calibrator divider ratio (CALDIV, ST6 Register) must be set accordingly. When the PLL is configured in Integer mode only (NINT ≥ 512, see Section 7.3: PLL N divider ) the calibrator divider should be bypassed (CALDIV = 1). In such a case, if the setup of the application requires a PFD frequency higher than 250 kHz the calibration procedure must be executed in two steps: 1. VCO calibration. Configure all the device registers (see Section 7.17: Example of register programming) making sure to program the desired VCO frequency with proper settings of the values N (ST0 Register) and R (ST3 Register) so that FPFD is ≤ 250 kHz 2. Final operating setup. Adjust the values N and R properly in order to program the device with the desired setup configuration (VCO and PFD frequency), and also set the VCO_CALB_DISABLE bit to ‘1’ (ST0 Register). Once the correct VCO and sub-band are selected the normal PLL operations are resumed. The VCO core can be supplied from 2.5 to 5 V. The LDO_4V5 regulator (programmable to 4.5 V, 3.3 V and 2.6 V) is used for this purpose. Furthermore, the amplitude of oscillation, which trades current consumption for phase noise performance, is 4-bit programmable (ST4 Register, VCO_AMP bit). Section 7.15: STW81200 register descriptions shows the allowed ranges of oscillation amplitude for each available supply setting. In order to achieve the best phase noise performance, the maximum amplitude setting is recommended. 7.10 RF output divider stage The signal coming from the VCOs is fed to a flexible RF divider stage. The divider ratio is programmable among different values (1, 2, 4, 8,16, 32 and 64) and allows the selection of the desired output frequency band: • 3.0 to 6.0 GHz (divider ratio = 1) • 1.5 to 3.0 GHz (divider ratio = 2) • 0.75 to 1.5 GHz (divider ratio = 4) • 375 to 750 MHz (divider ratio = 8) • 187.5 to 375 MHz (divider ratio = 16) • 93.75 to 187.5 MHz (divider ratio = 32) • 46.875 to 93.75 MHz (divider ratio = 64) The final output stage buffer (pins RF1_OUTP, RF1_OUTN) is internally broadband matched to 100-ohm differential (50-ohm single-ended) and it delivers up to +7 dBm of output power on a 100-ohm differential load (+4 dBm on 50-ohm from each single-ended output). The final output stage buffer has a 3-bit programmable output level and can be powered down by software and/or hardware (pin PD_RF1) while the internal PLL is locked. The related circuitry, together with VCO and charge pump, is compatible with supply voltages 30/61 DS10185 Rev 8 STW81200 Circuit description ranging from 2.5 V to 5 V. The regulator LDO_4V5, which supplies this block, can be set to 4.5 V, 3.3 V or 2.6 V. When supplied at 2.6 V, only the lowest 2 power levels are allowed (see ST4 Register settings, RF_OUT_PWR bit) An auxiliary output stage buffer (pins RF2_OUTP and RF2_OUTN) is available with the same features of the main one. The RF division ratio of this auxiliary output can be set independently from the main output in order to increase the flexibility. Furthermore it is possible to get, on the auxiliary output, a signal in phase or in quadrature with the main one, if the same frequency is selected on both outputs. The auxiliary output stage can also be powered down by software and/or hardware (pin PD_RF2). The output stage can be muted until the PLL achieves the lock status; this function can be activated by software. 7.11 Low-power functional modes All the performance characteristics defined in the electrical specifications are achieved in full current mode. The STW81200 is able to provide a set of low power functional modes which allows control of the current consumption of the different blocks. This feature can be helpful for those applications requiring low power consumption. The power saving modes trade the current consumption with the phase noise performance, and/or output level. The current of the blocks defined in Table 9 can be set by software, and the power saved on each block affect a specific performance as described in the same table. Table 9. Blocks with programmable current and related performance Block Current Control bits Affected Performance VCO Core ST4 Register bits[18:15] VCO phase noise (offset >PLL_BW) VCO Buffers and mux ST5 Register bits[12:11] Phase Noise Floor (offset > ~10 MHz) RF Dividers Core ST5 Register bits [10:4] Phase Noise Floor (offset > ~10 MHz) RF output stage ST4 Register bits [25:23] RF output level DS10185 Rev 8 31/61 60 Circuit description 7.12 STW81200 LDO voltage regulators Low drop-out (LDO) voltage regulators are integrated to provide the synthesizer with stable supply voltages against input voltage, load and temperature variations. Five regulators are included to ensure proper isolation among circuit blocks. These regulators are listed below along with the target specifications for the regulated output voltage and current capability: • LDO_DIG (to supply the digital circuitry), Vreg = 2.6 V, Imax = 50 mA, Vin Range: 3.0 to 5.4 V • LDO_REF (to supply the PLL), Vreg = 2.6 V, Imax = 50 mA, Vin Range: 3.0 to 5.4 V • LDO_RF (to supply the rf blocks), Vreg = 2.6 V, Imax = 100 mA, Vin Range: 3.0 to 5.4 V • LDO_VCO (to supply the low-voltage VCO sub-blocks): Vreg = 2.6 V, Imax = 100 mA, Vin Range: 3.0 to 5.4 V • LDO_4V5 (to supply high-voltage sub-blocks): Vreg = 4.5 V, 3.3 V and 2.6 V programmable, Imax = 150 mA Vin Range: 3.0 to 5.4 V (when Vreg=2.6 V) Vin Range: 3.6 to 5.4 V (when Vreg=3.3 V) Vin Range: 5.0 to 5.4 V (when Vreg=4.5 V) Proper stability and frequency response are achieved by adopting 10 µF load capacitors at the regulated output pins. The optimal configuration is achieved by connecting a small resistor in series with the capacitor in order to guarantee the controlled ESR required to ensure the proper phase margin, together with the best performance in terms of noise and PSRR. For a complete view of required connections and component values associated with the LDO output pins, see the related PCB schematics section available from the STW81200 product page on the ST website. Very-low noise requirements have been assumed for the design of the VCO-related regulators (LDO_VCO and LDO_4V5). To comply with the noise specifications, these LDOs exploit an additional external bypass (feed forward) capacitor of 100 nF. All LDOs include over-current protection to avoid short-circuit failures, as well as internal power ramping to minimize startup current peaks. All LDOs operate from a reference voltage of 1.35 V, which is internally generated by an integrated band-gap circuit and noise-filtered through an external 10 µF capacitor. 32/61 DS10185 Rev 8 STW81200 7.13 Circuit description STW81200 register programming The STW81200 has 12 registers (10 R/W + 2 Read-Only) programmed through an SPI digital interface. The protocol uses 3 wires (SDI, SCK, LE) for write mode plus an additional pin (LD_SDO) for read operation. Each register has 32 bits, one for Read/Write mode selection, 4 address bits and 27 data bits. Figure 31. SPI Protocol 1. Bit for double buffering used for some registers only The Data bits are stored in the internal shift register on the rising edge of SCK. The first bit, CO is used for mode selection (0=Write Operation, 1=Read Operation). The bit A[3:0] represents the register address, and D[26:0] are the data bits. In some registers, the first data bit D26 is used (when set to ‘1’) for double-buffering purposes. In this case the register content is stored in a temporary buffer and is transferred to the internal register once a write operation is done on the master register ST0. DS10185 Rev 8 33/61 60 Circuit description STW81200 Figure 32. SPI timing diagram Table 10. SPI timings Parameter Comments Min Typ Max Unit Tsetup data to clock setup time 4 - - ns Thold data to clock hold time 1 - - ns Tck clock cycle period 20 - - ns Tdi disable pulse width 4 - - ns Tcd clock-to-disable time 1 - - ns Tec enable-to-clock time 3 - - ns 34/61 DS10185 Rev 8 STW81200 7.14 Circuit description STW81200 register summary Table 11. SPI Register map (address 12 to 15 not available) Address Register Name Type Description Page 0x00 ST0_Register Read/Write Master register. N divider, CP current. Writing to this register starts a VCO calibration on page 36 0x01 ST1_Register Read/Write DoubleBuffered FRAC value, RF1 output control on page 37 0x02 ST2_Register Read/Write DoubleBuffered MOD value, RF2 output control on page 38 0x03 ST3_Register Read/Write DoubleBuffered R divider, CP leakage, CP down-split pulse, Ref. Path selection, Device power down on page 39 0x04 ST4_Register Read/Write Lock det. control, Ref. Buffer, CP supply mode, VCO settings, Output power control on page 41 0x05 ST5_Register Read/Write Low power mode control bit on page 43 0x06 ST6_Register Read/Write VCO Calibrator, Manual VCO control, DSM settings on page 44 0x07 ST7_Register Read/Write Fast Lock control, LD_SDO settings on page 46 0x08 ST8_Register Read/Write LDO Voltage Regulator settings on page 47 0x09 ST9_Register Read/Write Reserved (Test & Initialization bit) on page 48 0x0A ST10_Register Read Only VCO, Lock det. Status, LDO status on page 49 0x0B ST11_Register Read Only Device ID on page 50 DS10185 Rev 8 35/61 60 Circuit description 7.15 STW81200 STW81200 register descriptions 21 20 19 RW RW RW 18 17 N[16:0] 22 RESERVED 23 PFD_DEL[1:0] 24 CP_SEL[4:0] 25 VCO_CALB_DISABLE 26 RESERVED ST0 Register 16 15 14 13 RW RW RW Address: STW81200BaseAddress + 0x00 Type: R/W Description: Master register. N divider, CP current 12 11 10 9 8 7 6 5 4 3 [26] VCO_CALB_DISABLE: must be set to ‘0’. Setting this bit to ‘1’ disables the VCO calibrator. (Note: this bit is write-only and cannot be read. A read operation always returns a '1') [25:21] CP_SEL: Set charge pump pulse current value (0 to 4.9 mA; step ~158 µA) 00000: (0) set ICP=0 00001: (1) set ICP=158 µA 00010: (2) set ICP=316 µA … 11110: (30) set ICP=4.74 mA 11111: (31) set ICP=4.90 mA [20:19] PFD_DEL: Set PFD anti-backlash delay / down-split current value 00: (0) 1.2 ns / 0 A (default) 01: (1) 1.9 ns / 0.25*ICP 10: (2) 2.5 ns / 0.5*ICP 11: (3) 3.0 ns / 0.75*ICP [18] RESERVED: must be set to ‘0’ [17] RESERVED: must be set to ‘0’ [16:0] N: Set integer part of N divider ratio (NINT) For NINT ≥ 512, fractional mode is not allowed (FRAC and MOD settings are ignored) 36/61 DS10185 Rev 8 2 1 0 STW81200 Circuit description 24 RESERVED RF1_OUT_PD 23 RW RW RW 22 21 20 19 18 17 16 15 14 13 12 11 10 FRAC[20:0] 25 RF1_DIV_SEL[2:0] 26 DBR ST1 Register RW RW Address: STW81200BaseAddress + 0x01 Type: R/W Applicability: Double buffered (based upon DBR bit setting) Description: FRAC value, RF1 output control 9 8 7 6 5 4 3 2 1 0 [26] DBR: Double buffering bit enable; at ‘1’ the register is buffered and transferred only once the master register ST0 is written [25] RESERVED: must be set to ‘0’ [24] RF1_OUT_PD: RF1 output power down 0 = RF1 output enabled 1 = RF1 output disabled [23:21] RF1_DIV_SEL: RF1 output divider selection 000: (0) VCO direct 001: (1) VCO divided by 2 010: (2) VCO divided by 4 011: (3) VCO divided by 8 100: (4) VCO divided by 16 101: (5) VCO divided by 32 110: (6) VCO divided by 64 111: (7) Reserved [20:0] FRAC: Fractional value bit; set the numerator value of the fractional part of the overall division ratio (N=NINT+FRAC/MOD) Range: 0 to 2097151 (must be < MOD) DS10185 Rev 8 37/61 60 Circuit description STW81200 24 RESERVED RF2_OUT_PD 23 RW RW RW 22 21 20 19 18 17 16 15 14 13 12 11 10 MOD[20:0] 25 RF2_DIV_SEL[2:0] 26 DBR ST2 Register RW RW Address: STW81200BaseAddress + 0x02 Type: R/W Applicability: Double buffered (based upon DBR bit setting) Description: MOD value, RF2 output control 9 8 7 6 5 4 3 2 1 [26] DBR: Double buffering bit enable; at ‘1’ the register is buffered and transferred only once the master register ST0 is written [25] RESERVED: must be set to ‘0’ [24] RF2_OUT_PD: RF2 output power down 0 = RF2 output enabled 1 = RF2 output disabled [23:21] RF2_DIV_SEL: RF2 output divider selection 000: (0) VCO direct 001: (1) VCO divided by 2 010: (2) VCO divided by 4 011: (3) VCO divided by 8 100: (4) VCO divided by 16 101: (5) VCO divided by 32 110: (6) VCO divided by 64 111: (7) same divided output of RF1 (not valid if RF1_DIV_SEL=0) [20:0] MOD: Modulus value bit; set the denominator value of the fractional part of the overall division ratio (N=NINT+FRAC/MOD) Range: 2 to 2097151 38/61 DS10185 Rev 8 0 STW81200 Circuit description CP_LEAK[4:0] 21 RW RW RW RW 20 19 18 17 R[12:0] CP_LEAK_x2 22 REF_PATH_SEL[1:0] PD 23 PFD_DEL_MODE[1:0] 24 DNSPLIT_EN 25 CP_LEAK_DIR 26 DBR ST3 Register 16 15 14 13 12 11 10 9 8 7 6 RW RW RW RW RW 5 4 3 2 1 0 Address: STW81200BaseAddress + 0x03 Type: R/W Applicability: Double buffered (based upon DBR bit setting) Description: R divider, CP leakage, CP down-split pulse, Ref. Path selection, Device power down [26] DBR: Double buffering bit enable; at ‘1’ the register is buffered and transferred only once the master register ST0 is written [25] PD: device power down; at ‘1’ put OFF all blocks (except LDOs) [24] CP_LEAK_x2: double Charge Pump leakage current bit 0 = set standard leakage current (10 µA step) 1 = set doubled leakage current (20 µA step) [23:19] CP_LEAK: Set Charge Pump leakage current value (0 to 620 μA; step 10 μA or 20 μA base upon CP_LEAK_x2 setting) 00000: (0) set ILEAK = 0 (default) 00001: (1) set ILEAK = 10 μA (ILEAK = 20 μA if CP_LEAK_x2 = 1) 00010: (2) set ILEAK = 20 μA (ILEAK = 40 μA if CP_LEAK_x2 = 1) … 11110: (30) set ILEAK = 300 μA (ILEAK = 600 μA if CP_LEAK_x2 = 1) 11111: (31) set ILEAK = 310 μA (ILEAK = 620 μA if CP_LEAK_x2 = 1) [18] CP_LEAK_DIR: set direction of the leakage current 0: set down-leakage (current sink) 1: set up-leakage (current source) [17] DNSPLIT_EN: at ‘1’ enables down-split pulse current; current level set by PFD_DEL[1:0] in register ST0 DS10185 Rev 8 39/61 60 Circuit description STW81200 [16:15] PFD_DEL_MODE: set PFD delay mode; delay values set by PFD_DEL[1:0] in register ST0 00: (0) no delay (default) 01: (1) VCO_DIV delayed 10: (2) REF_DIV delayed 11: (3) Reserved [14:13] REF_PATH_SEL: reference clock path selection 00: (0) Direct 01: (1) Doubled in single mode; Not Applicable in differential mode 10: (2) Divided by 2 11: (3) Divided by 4 [12:0] R: set Reference clock divider ratio (1 to 8191) 40/61 DS10185 Rev 8 STW81200 Circuit description RW RW RW 11 10 RW RW 9 8 RW 7 6 LD_COUNT[2:0] 12 LD_PREC[2:0] 13 LD_ACTIVELOW 14 REF_BUFF_MODE[1:0] 15 PFD_POL 16 KVCO_COMP_DIS 17 MUTE_LOCK_EN RW RW RW RW 18 CP_SUPPLY_MODE[1:0] 19 PLL_MUX_DIV 20 VCO_AMP[3:0] 21 EXT_VCO_EN RW 22 RESERVED RW 23 RESERVED 24 RF_OUT_PWR[2:0] 25 RESERVED 26 VCO_2V5_MODE ST4 Register 5 4 3 2 RW RW RW RW Address: STW81200BaseAddress + 0x04 Type: R/W Description: Lock det. control, Ref. Buffer, CP supply mode, VCO settings, Output power control 1 0 [26] RESERVED: must be set to ‘0’ [25:23] RF_OUT_PWR: RF output power control bit; set output power level of differential signal (valid for both RF1 and RF2 outputs; measured @ 4 GHz). When VCC_RFOUT is supplied at 2.6 V ‘0’ and ‘1’ are the only values allowed. 000: (0) -1.0 dBm (-4.0 dBm on each single-ended signal) 001: (1) +1.0 dBm (-2.0 dBm on each single-ended signal) 010: (2) +2.5 dBm (-0.5 dBm on each single-ended signal) 011: (3) +3.5 dBm (+0.5 dBm on each single-ended signal) 100: (4) +4.5 dBm (+1.5 dBm on each single-ended signal) 101: (5) +5.5 dBm (+2.5 dBm on each single-ended signal) 110: (6) +6.5 dBm (+3.5 dBm on each single-ended signal) 111: (7) +7.0 dBm (+4.0 dBm on each single-ended signal) [22] VCO_2V5_MODE: to be set to ‘1’ when VCO core (pin #3) is supplied at 2.6 V [21] RESERVED: must be set to ‘0’ [20] RESERVED: must be set to ‘0’ [19] EXT_VCO_EN: external VCO Buffer enable 0: external VCO buffer disabled; integrated VCOs are used 1: external VCO buffer enabled; external VCO required (internal VCOs are powered down) [18:15] VCO_AMP: set VCO signal amplitude at the internal oscillator circuit nodes; higher signal level gives best phase noise performance while lower signal level gives low current consumption. Different ranges of value are available, based upon the supply voltage provided to pin VCC_VCO_core (pin #3). Allowed settings: 0000 to 0110: (0-6) when VCO core is supplied at 2.6 V 0000 to 1010: (0-10) when VCO core is supplied at 3.3 V 0000 to 1111: (0-15) when VCO core is supplied at 4.5/5 V DS10185 Rev 8 41/61 60 Circuit description STW81200 [14] PLL_MUX_DIV: PLL MUX setting; select the desired signal path from VCO to the N Divider (VCO divider in the PLL feedback path): 0: VCO direct to N Divider (default) 1: VCO divided to N Divider (division ratio set by RF1_DIV_SEL in register ST1) [13:12] CP_SUPPLY_MODE: Charge Pump supply mode settings; value to be set according to the supply used for charge pump core circuit (pin #16) 00: (0) 4.5V to 5.0 V 01: (1) 3.3 V 10: (2) 2.6 V 11: (3) Reserved [11] KVCO_COMP_DIS: disable KVCO compensation circuit 0: compensation enabled (default - CP current auto-adjusted to compensate KVCO variation) 1: compensation disabled (CP current fixed by CP_SEL settings) [10] PFD_POL: set PFD polarity 0: standard mode (default) 1: “inverted” mode (to be used only with active inverting loop filter or with VCO with negative tuning characteristics) [9:8] REF_BUFF_MODE: set Reference Clock buffer mode 00: (0) Reserved 01: (1) Differential Mode (Ref. clock signal on pin #20 and #21) 10: (2) XTAL Mode (Xtal oscillator enabled with crystal connected on pin #20 and #21) 11: (3) Single Ended Mode (Ref. clock signal on pin #21) [7] MUTE_LOCK_EN: enables mute function 0: “mute on unlock” function disabled 1: “mute on unlock” function enabled (RF output stages are put OFF when PLL is unlocked) [6] LD_ACTIVELOW: set low state as lock indicator 0: set lock indicator active high (LD=0 means PLL unlocked; LD=1 means PLL locked) 1: set lock indicator active low (LD=0 means PLL locked; LD=1 means PLL unlocked) [5:3] LD_PREC: set Lock Detector precision 000: (0) 2 ns (default for Integer Mode) 001: (1) 4 ns (default for Fractional Mode) 010: (2) 6 ns 011: (3) 8 ns 100: (4) 10 ns 101: (5) 12 ns 110: (6) 14 ns 111: (7) 16 ns [2:0] LD_COUNT: set Lock Detector counter for lock condition 000: (0) 4 001: (1) 8 (default for FPFD ~1 MHz in Integer Mode) 010: (2) 16 011: (3) 64 100: (4) 256 101: (5) 1024 (default for FPFD ~50 MHz in both Fractional/Integer Mode) 110: (6) 2048 111: (7) 4096 42/61 DS10185 Rev 8 STW81200 Circuit description RW RW RW 12 11 10 9 8 7 6 5 4 3 2 1 0 REF_BUFF_LP 13 RESERVED 14 PLL_MUX_LP 15 RESERVED 16 RF_DIV_MUXOUT_LP 17 RF_DIV64_LP 18 RF_DIV32_LP 19 RF_DIV16_LP 20 RF_DIV8_LP 21 RF_DIV4_LP 22 RF_DIV2_LP 23 VCO_MUX_LP RESERVED 24 VCO_BUFF_LP 25 RESERVED 26 RESERVED ST5 Register RW RW RW RW RW RW RW RW RW RW RW RW RW Address: STW81200BaseAddress + 0x05 Type: R/W Description: Low power mode control bit [26] RESERVED: must be set to ‘0’ [25] RESERVED: must be set to ‘0’ [24:13] RESERVED: must be set to ‘0’ [12] VCO_BUFF_LP: VCO Buffer low power mode (0=full power; 1=low power) [11] VCO_MUX_LP: VCO MUX low power mode (0=full power; 1=low power) [10] RF_DIV2_LP: RF Div. by 2 low power mode (0=full power; 1=low power) [9] RF_DIV4_LP: RF Div. by 4 low power mode (0=full power; 1=low power) [8] RF_DIV8_LP: RF Div. by 8 low power mode (0=full power; 1=low power) [7] RF_DIV16_LP: RF Div. by 16 low power mode (0=full power; 1=low power) [6] RF_DIV32_LP: RF Div. by 32 low power mode (0=full power; 1=low power) [5] RF_DIV64_LP: RF Div. by 64 low power mode (0=full power; 1=low power) [4] RF_DIV_MUXOUT_LP: RF Div. MUX low power mode (0=full power; 1=low power) [3] RESERVED: must be set to ‘0’ [2] PLL_MUX_LP: MUX PLL low power mode (0=full power; 1=low power) [1] RESERVED: must be set to ‘0’ [0] REF_BUFF_LP: Ref. Buffer low power mode (0=full power; 1=low power) DS10185 Rev 8 43/61 60 Circuit description STW81200 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 CAL_DIV[8:0] RW RW 19 CAL_ACC_EN RW 20 PRCHG_DEL[1:0] DSM_ORDER[1:0] RW RW RW 21 CAL_TEMP_COMP CP_DN_OFF 22 VCO_WORD[4:0] CP_UP_OFF 23 VCO_SEL[1:0] 24 MAN_CALB_EN 25 DSM_CLK_DISABLE 26 DITHERING ST6 Register RW RW RW RW RW RW Address: STW81200BaseAddress + 0x06 Type: R/W Description: VCO Calibrator, Manual VCO control, DSM settings 3 2 1 0 [26] DITHERING: at ‘1’ enables dithering of DSM output sequence [25] CP_UP_OFF: for test purposes only; must be set to ‘0’ [24] CP_DN_OFF: for test purposes only; must be set to ‘0’ [23:22] DSM_ORDER: set the order of Delta-Sigma Modulator 00: (0) 3rd order DSM (recommended) 01: (1) 2nd order DSM 10: (2) 1st order DSM 11: (3) 4th order DSM [21] DSM_CLK_DISABLE: for test purposes only; must be set to ‘0’ [20] MAN_CALB_EN: enables manual VCO calibrator mode 0: automatic VCO calibration (VCO_SEL, VCO_WORD settings are ignored) 1: manual VCO calibration (VCO_SEL, VCO_WORD settings are used and the VCO calibration procedure is inhibited) [19:18] VCO_SEL: VCO selection bit 00: (0) VCO_HIGH 01: (1) VCO_LOW 10: (2) VCO_MID 11: (3) VCO_LOW [17:13] VCO_WORD: select specific VCO sub-band (range:0 to 31) [12] CAL_TEMP_COMP: at ‘1’ enables temperature compensation for VCO calibration procedure (to be used when PLL Lock condition is required on extremes thermal cycles) 44/61 DS10185 Rev 8 STW81200 Circuit description [11:10] PRCHG_DEL: set the number of calibration slots for pre-charge of VCTRL node at the Voltage reference value used during VCO calibration procedure 00: (0) 1 slot (default) 01: (1) 2 slots 10: (2) 3 slots 11: (3) 4 slots [9] CAL_ACC_EN: at ‘1’ increase calibrator accuracy by removing residual error taking 2 additional calibration slots (default = ‘0’) [8:0] CAL_DIV: Set Calibrator Clock divider ratio (Range:1 to 511); ‘0’ set the maximum ratio (‘511’) DS10185 Rev 8 45/61 60 Circuit description STW81200 LD_SDO_MODE SPI_DATA_OUT_DISABLE LD_SDO_SEL[1:0] RW RW RW RW RW 20 19 18 FSTLCK_CNT[12:0] LD_SDO_tristate 22 CP_SEL_FL[4:0] 23 FSTLCK_EN 24 CYCLE_SLIP_EN 25 REGDIG_OCP_DIS 26 RESERVED ST7 Register 21 17 16 15 14 13 RW RW RW RW RW Address: STW81200BaseAddress + 0x07 Type: R/W Description: Fast Lock control, LD_SDO settings 12 11 10 9 8 7 6 5 4 3 2 1 0 [26] RESERVED: must be set to ‘0’ [25] LD_SDO_tristate: at ‘1’ put LD_SDO out pin in Tri-State mode [24] LD_SDO_MODE: LD_SDO output interface mode selection 0: Open Drain mode (Level Range: 1.8V to 3.6V) 1: 2.5V CMOS output mode [23] SPI_DATA_OUT_DISABLE: disable auto-switch of LD_SDO pin during SPI read mode 0: LD_SDO pin automatically switched to SPI data out line during SPI read mode 1: LD_SDO pin fixed to Lock detector indication (SPI read operation not possible) [22:21] LD_SDO_SEL: LD_SDO Mux output selection bit 00: (0) Lock Detector (default) 01: (1) VCO Divider output (for test purposes only) 10: (2) Calibrator VCO Divider output (for test purposes only) 11: (3) Fast Lock clock output (for test purposes only) [20] REGDIG_OCP_DIS: for test purposes only ; must be set to ‘0’ (at ‘1’ disable the over-current protection of Digital LDO Voltage Regulator) [19] CYCLE_SLIP_EN: at ‘1’ enables Cycle Slip feature [18] FSTLCK_EN: at ‘1’ enables Fast lock mode using pin #6 (PD_RF2/FL_SW) [17:13] CP_SEL_FL: set the Charge Pump current during fast lock time slot (range:0 to 31) [12:0] FSTLCK_CNT: Fast-Lock counter value (Range: 2 to 8191); set duration of fast-lock time slot as number of FPFD cycles 46/61 DS10185 Rev 8 STW81200 Circuit description RESERVED RESERVED RESERVED REG_OCP_DIS REG_DIG_PD 13 RW RW RW Address: STW81200BaseAddress + 0x08 Type: R/W Description: LDO Voltage Regulator settings 12 11 10 RW RW 9 8 RW 7 6 5 RW RW 4 RW 3 2 REG_VCO_4V5_VOUT[1:0] RESERVED 14 REG_VCO_4V5_PD RW 15 RESERVED RESERVED 16 REG_VCO_VOUT[1:0] RESERVED RW RW RW RW RW RW RW RW RW 17 REG_VCO_PD 18 RESERVED 19 REG_RF_VOUT[1:0] 20 REG_RF_PD 21 RESERVED 22 REG_REF_VOUT[1:0] 23 REG_REF_PD 24 RESERVED 25 REG_DIG_VOUT[1:0] 26 PD_RF2_DISABLE ST8 Register 1 0 RW RW RW [26] PD_RF2_DISABLE: at ‘1’ disable the hardware power down function of the pin PD_RF2 (pin #6) thus allowing the pin PD_RF1 (pin #5) to control the power down status of both RF Output stages [25] RESERVED: must be set to ‘0’ [24] RESERVED: must be set to ‘0’ [23] RESERVED: must be set to ‘0’ [22] RESERVED: must be set to ‘0’ [21] RESERVED: must be set to ‘0’ [20] RESERVED: must be set to ‘0’ [19] REG_OCP_DIS: for test purposes only; must be set to ‘0’ (at ‘1’ disable the over-current protection of LDO Voltage Regulators except DIG regulator) [18] REG_DIG_PD: DIGITAL Regulator power down; must be set to ‘0’ [17:16] REG_DIG_VOUT: DIGITAL Regulator output voltage set 00: (0) 2.6 V (Default) 01: (1) 2.3 V (for test purposes only) 10: (2) 2.4 V (for test purposes only) 11: (3) 2.5 V (for test purposes only) [15] RESERVED: must be set to ‘0’ [14] REG_REF_PD: REFERENCE CLOCK Regulator power down; must be set to ‘0’ [13:12] REG_REF_VOUT: REFERENCE CLOCK Regulator output voltage set 00: (0) 2.6 V (default) 01: (1) 2.5 V (for test purposes only) 10: (2) 2.7 V (for test purposes only) 11: (3) 2.8 V (for test purposes only) [11] RESERVED: must be set to ‘0’ [10] REG_RF_PD: RF Output section Regulator power down; must be set to ‘0’ DS10185 Rev 8 47/61 60 Circuit description STW81200 [9:8] REG_RF_VOUT: RF Output section Regulator output voltage set 00: (0) 2.6 V (default) 01: (1) 2.5 V (for test purposes only) 10: (2) 2.7 V (for test purposes only) 11: (3) 2.8 V (for test purposes only) [7] RESERVED: must be set to ‘0’ [6] REG_VCO_PD: VCO bias-and-control regulator power down; must be set to ‘0’ [5:4] REG_VCO_VOUT: VCO bias-and-control regulator output voltage set 00: (0) 2.6 V (default) 01: (1) 2.5 V (for test purposes only) 10: (2) 2.7 V (for test purposes only) 11: (3) 2.8 V (for test purposes only) [3] RESERVED: must be set to ‘0’ [2] REG_VCO_4V5_PD: High-voltage regulator power down (to be used to supply VCO core, RF output final stage and Charge Pump). Must be set to ‘0’ [1:0] REG_VCO_4V5_VOUT: High-voltage regulator output voltage set (to be used to supply VCO core, RF output final stage and charge-pump output) 00: (0) 5.0 V (Require 5.4 V unregulated voltage line on pin# 36 for test purposes only) 01: (1) 2.6 V (3.0-5.4 V unregulated voltage line Range allowed on pin#36) 10: (2) 3.3 V (3.6-5.4 V unregulated voltage line Range allowed on pin#36) 11: (3) 4.5 V (5.0-5.4 V unregulated voltage line Range allowed on pin#36) ST9 Register 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 RESERVED 26 RW Address: STW81200BaseAddress + 0x09 Type: R/W Description: Reserved (Test & Initialization bit) [26:0] RESERVED: Test & Initialization bit; must be set to ‘0’ 48/61 DS10185 Rev 8 10 9 8 7 6 5 4 3 2 1 0 STW81200 Circuit description 17 16 15 14 13 12 11 10 9 8 7 REG_VCO_STARTUP REG_VCO_4V5_STARTUP REG_DIG_OCP REG_REF_OCP REG_RF_OCP REG_VCO_OCP REG_VCO_4V5_OCP LOCK_DET VCO_SEL[1:0] WORD[4:0] 23 REG_RF_STARTUP 24 REG_REF_STARTUP 25 REG_DIG_STARTUP 26 RESERVED ST10 Register 22 21 20 19 18 R R R R R R R R R R R R R R Address: STW81200BaseAddress + 0x0A Type: R Description: VCO, Lock det. Status, LDO status 6 5 4 3 2 1 0 [26:18] RESERVED: fixed to ‘0’ [17] REG_DIG_STARTUP: DIGITAL regulator ramp-up indicator (‘1’ means correct start-up) [16] REG_REF_STARTUP: REFERENCE CLOCK regulator ramp-up indicator (‘1’ means correct start-up) [15] REG_RF_STARTUP: RF Output section regulator ramp-up indicator (‘1’ means correct start-up) [14] REG_VCO_STARTUP: VCO bias-and-control regulator ramp-up indicator (‘1’ means correct start-up) [13] REG_VCO_4V5_STARTUP: High-voltage regulator ramp-up indicator (‘1’ means correct start-up) [12] REG_DIG_OCP: DIGITAL regulator over-current protection indicator (‘1’ means over-current detected) [11] REG_REF_OCP: REFERENCE CLOCK regulator over-current protection indicator (‘1’ means overcurrent detected) [10] REG_RF_OCP: RF Output section regulator over-current protection indicator (‘1’ means over-current detected) [9] REG_VCO_OCP: VCO Bias and Control regulator over-current protection indicator (‘1’ means over-current detected) [8] REG_VCO_4V5_OCP: High Voltage regulator over-current protection indicator (‘1’ means over-current detected) [7] LOCK_DET: Lock detector status bit (‘1’ means PLL locked) [6:5] VCO_SEL: VCO selected by Calibration algorithm 00: (0) VCO_HIGH 01: (1) VCO_LOW 10: (2) VCO_MID 11: (3) VCO_LOW [4:0] WORD: specific VCO sub-band selected by Calibration algorithm (Range:0 to 31) DS10185 Rev 8 49/61 60 Circuit description STW81200 ST11 Register 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 Device_ID 26 R Address: STW81200BaseAddress + 0x0B Type: R Description: Device ID [26:0] Device_ID: Device Identifier (0x0008021) 50/61 DS10185 Rev 8 10 9 8 7 6 5 4 3 2 1 0 STW81200 7.16 Circuit description Power ON sequence In order to guarantee the correct start-up of the internal circuitry after the power on, the following steps must be followed: 1. Power up the device (LDO supply pins: pin#9 #18, #28 and #36) 2. Once the voltages applied on the LDO supply pins are stable, wait 50 ms. (After this transient time, the LDOs are powered on with the regulated voltages available at pins #2, #8, #19, #27 and #29, while all other circuits are in power down mode) 3. Provide the reference clock signal 4. Implement the first programming sequence as follows: 5. 7.17 a) Program register ST9 (test and initialization) with all bit set to ‘0’ b) Program register ST0 according to the desired configuration c) Program the following registers in the specified order according to the desired configuration: ST8, ST7, ST6, ST5, ST4, ST3, ST2, ST1, ST0 Check the PLL Lock status on pin LD_SDO (pin #26) and/or read all relevant information provided on registers ST10 and ST11. Example of register programming Setup conditions and requirements: • Unregulated Supply voltage: 5.0 V • Reference Clock: 122.88 MHz, single-ended, sine wave • LO Frequency: 2646.96 MHz – exact freq. mode (VCO Frequency=5293.92 MHz) • Output Power: +7 dBm (differential) • Phase Noise requirements: full performance VCO, full performance Noise floor. Register configurations (Hex values including register address) • ST9 = 0x48000000 (initialization; all bits set to ‘0’) • ST8 = 0x40000003 (REG_4V5 = 4.5 V) • ST7 = 0x39000000 (“fast lock” not used; LD_SDO pin configured as 2.5 V CMOS buffer) • ST6 = 0x30001000 (DITHERING=0; DSM_ORDER=0 for 3rd order DSM; CAL_TEMP_COMP=1 to guarantee lock on extreme temperature drift) • ST5 = 0x28000000 (low power modes not used) • ST4 = 0x2387838D (lock detector setting for fractional mode and FPFD = 61.44 MHz; REF_BUF_MODE=3 for single-ended mode; VCO_AMP=15 for best VCO phase noise @4.5 V supply; RF_OUT_PWR=7 to have +7 dBm differential) • ST3 = 0x18008002 (PFD_DEL_MODE = ‘VCO_DIV_delayed’, R=2 and REF_PATH_SEL = 0 ‘direct’ for FPFD= 61.44 MHz) • ST2 = 0x13000080 (MOD=128; RF2_OUT_PD=1 for RF2 Output in power down) • ST1 = 0x08200015 (FRAC=21; RF1_DIVSEL=1 set RF1 Output with VCO freq. Divided By 2) • ST0 = 0x03E00056 (NINT=86; PFD_DEL = 1.2 ns; CPSEL = 31 for Icp = 4.9 mA) DS10185 Rev 8 51/61 60 Application information STW81200 8 Application information 8.1 Application diagrams Figure 33. Application diagram (internal VCO) Note: 52/61 This diagram shows a simplified schematic; the Evaluation Board schematic should be used as reference for connections and components values. Visit the STW81200 product page on the ST website www.st.com/stw81200ad to download the Evaluation Board Data Brief including PCB schematics. DS10185 Rev 8 STW81200 Application information Figure 34. Application diagram (external VCO) Note: This diagram shows a simplified schematic; the Evaluation Board schematic should be used as reference for connections and components values. Visit the STW81200 product page on the ST website www.st.com/stw81200ad to download the evaluation board data brief including PCB schematics. DS10185 Rev 8 53/61 60 Application information 8.2 STW81200 Thermal PCB design considerations The STW81200 QFN package offers a low thermal resistance (θJC ~3°C/W on a JEDEC Multi-Layer Board). Preferred thermal flow in QFN package is through the bottom central pad. The central thermal pad provides a solderable surface on the top of the PCB (for soldering the package die paddle on the board). Thermal vias are needed to provide a thermal path to the inner and bottom layers of the PCB in order to remove/dissipate the heat. The size of the thermal pad can be matched with the exposed die paddle, or it may be smaller taking into consideration clearance for vias to route the inner row signals. A PCB can be designed to achieve a thermal impedance of 2 to 4°C/W through a 1.6 mm (.063”) thick FR-4 type PCB (a reliable, low cost solution). For example the ST EVAL KIT uses a 0.8 mm thick PCB with a thermal impedance of ~50°C/W for a single via filled with solder. 25 vias are used, giving a thermal impedance of ~2°C/W with solder-filled vias (50°C/W divided by 25 vias). Using a plate on the underside of the PCB (a common solution in STW81200 applications, as the plate is typically the metal housing of the application assembly) brings the total thermal resistance (junction to housing in the customer application) below 10°C/W. As the typical power dissipation of the STW81200 is approximately 1.5 W, at maximum specified ambient temperature (85°C) a junction temperature of less than 100°C is attainable. This is well below the maximum specified value (125°C) to ensure safe operation of the STW81200 in worst-temperature conditions. The ST EVAL KIT is not provided with additional heatsinking, and the thermal resistance (θJA) measured in the EVAL BOARD is ~30°C/W. 54/61 DS10185 Rev 8 STW81200 9 Evaluation kit Evaluation kit An evaluation kit can be supplied upon request (Order Code: STW81200-EVB), including the following: • Evaluation board • GUI (graphical user interface) to configure the board and the STW81200 IC • STWPLLSim software for PLL loop filter design and phase noise/transient simulation • A comprehensive set of documentation (Evaluation board data brief including PCB schematics and GUI help, STWPLLSim User Manual). The evaluation kit and the related SW and documentation can be ordered/downloaded from the ST website at the following address: www.st.com/stw81200ad. Table 12. STW81200 order codes Order Code Description STW81200-EVB STW81200 Evaluation Kit (Evaluation Board, GUI and STWPLLSim tool) STSW-RFSOL001 STWPLLSim simulation tool for STW81200 STSW-RFSOL002 GUI for configuring STW81200 evaluation board DS10185 Rev 8 55/61 60 Package information 10 STW81200 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 10.1 VFQFPN36 package information Figure 35. VFQFPN - 36 pin, 6x6 mm, 0.5 mm pitch very thin profile fine pitch quad flat package outline 6HDWLQJSODQH $ & GGG & $ $ $ ' H 3LQ,'5     E  ( (     ' / . / =5B0(B9 1. Drawing is not to scale. 56/61 DS10185 Rev 8 STW81200 Package information Table 13. VFQFPN - 36 pin, 6x6 mm, 0.5 mm pitch very thin profile fine pitch quad flat package mechanical data inches(1) millimeters Symbol Min Typ Max Min Typ Max A 0.800 0.900 1.000 0.0315 0.0354 0.0394 A1 - 0.020 0.050 - 0.0008 0.0020 A2 - 0.650 1.000 - 0.0256 0.0394 A3 - 0.200 - - 0.0079 - b 0.180 0.230 0.300 0.0071 0.0091 0.0118 D 5.875 6.000 6.125 0.2313 0.2362 0.2411 D2 4.00 4.10 4.20 0.1575 0.1614 0.1654 E 5.875 6.000 6.125 0.2313 0.2362 0.2411 E2 4.00 4.10 4.20 0.1575 0.1614 0.1654 e 0.450 0.500 0.550 0.0177 0.0197 0.0217 L 0.350 0.550 0.750 0.0138 0.0217 0.0295 K 0.250 - - 0.0098 - - ddd - - 0.080 - - 0.0031 1. Values in inches are converted from mm and rounded to 4 decimal digits. DS10185 Rev 8 57/61 60 Package information STW81200 Figure 36. VFQFPN - 36 pin, 6x6 mm, 0.5 mm pitch very thin profile fine pitch quad flat package recommended footprint                    :2?&0?6 1. Dimensions are expressed in millimeters. 58/61 DS10185 Rev 8 STW81200 11 Revision history Revision history Table 14. Document revision history Date Revision 21-Feb-2014 1 Initial release. 07-Apr-2014 2 Removed confidential banner 04-Sep-2014 3 Added HBM footnote in Table 3: Absolute maximum ratings Updated device ID in ST11 Register on page 50 Updated to use latest corporate template and legal disclaimer. 23-Sep-2014 4 Changed ‘Multi-band’ to ‘Wideband’ in document title. 12-Jun-2015 5 Renamed pin 14 to VDD_CP in Table 2: Pin description. Added IOL and IOH values in Table 5: Digital logic levels Updated parameter VICP in Table 6: Electrical specifications Updated Figure 9 through Figure 28 Added Section 7.3.1: Fractional spurs and compensation mechanism. Updated – Section 7.6: Charge pump. – Section 7.9: Voltage controlled oscillators (VCOs) – Section 7.10: RF output divider stage – Section 7.11: Low-power functional modes – Section 7.12: LDO voltage regulators Updated ST0 register description in Table 11: SPI Register map (address 12 to 15 not available) Updated following register bitfield descriptions: – STW81200 register descriptions bit PFD_DEL – ST3 Register bits CP_LEAK and DNSPLIT_EN – ST4 Register bit RF_OUT_PWR – ST6 Register bit MAN_CALB_EN – ST8 Register bit REG_VCO_4V5_VOUT – ST10 Register bit REG_VCO_OCP Updated Section 7.17: Example of register programming Added notes to Figure 33 and Figure 34 Added Section 9: Evaluation kit Re formatted Section 10: Package information to comply with latest corporate guidelines. 08-Jul-2015 6 Regenerated for XML generation. 7 Updated parameter Kvco in Table 6: Electrical specifications Updated: – Section 7.6: Charge pump – Section 7.16: Power ON sequence. Re-named Section 8: Application information, and added Section 8.2: Thermal PCB design considerations. In Table 6: Electrical specifications updated dimensions D2 and E2. 04-Jan-2016 Changes DS10185 Rev 8 59/61 60 Revision history STW81200 Table 14. Document revision history Date 09-Aug-2019 60/61 Revision 8 Changes Updated Section 7.9: Voltage controlled oscillators (VCOs). Detailed VCO_CALB_DISABLE bit in ST0 Register. Updated Section 10: Package information. DS10185 Rev 8 STW81200 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. For additional information about ST trademarks, please refer to www.st.com/trademarks. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2019 STMicroelectronics – All rights reserved DS10185 Rev 8 61/61 61