T1010H-6T

T1010H High temperature 10 A sensitive TRIACs Features A2 ■ Medium current TRIAC ■ Logic level sensitive TRIAC ■ 150 °C max. Tj turn-off commutation ■ Clip bounding ■ RoHS (2002/95/EC) compliant packages G A1 A2 Applications A2 ■ The T1010H is designed for the control of AC actuators in appliances and industrial systems. ■ The multi-port drive of the microcontroller can control the multiple loads of such appliances and systems through these sensitive gate TRIACs. A2 G G A2 A1 A1 D2PAK T1010H-6G TO-220AB T1010H-6T Description Specifically designed to operate at 150 °C, the new 10 A T1010H TRIACs provide an enhanced performance in terms of power loss and thermal dissipation. This allows the optimization of the heatsink size, leading to space and cost effectiveness when compared to electromechanical solutions. Based on ST logic level technology, they offer an IGT lower than 10 mA and specified minimal commutation and high noise immunity levels valid up to the Tj max. May 2009 Table 1. Device summary Symbol Value Unit IT(RMS) 10 A VDRM/VRRM 600 V IGT MAX 10 mA Doc ID 15715 Rev 1 1/10 www.st.com 10 Characteristics T1010H 1 Characteristics Table 2. Absolute maximum ratings Symbol Parameter Value Unit A IT(RMS) On-state rms current (full sine wave) D2PAK, TO-220AB Tc = 135 °C 10 Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) F = 60 Hz t = 16.7 ms 105 ITSM F = 50 Hz t = 20 ms 100 I²t Value for fusing tp = 10 ms Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns F = 120 Hz Non repetitive surge peak off-state voltage Peak gate current I²t dI/dt VDSM/VRSM IGM PG(AV) Tstg Tj Table 3. VGT VGD IH (1) IL dV/dt (1) (dI/dt)c (1) 66 A ²s Tj = 150 °C 50 A/µs tp = 10 ms Tj = 25 °C VDRM/VRRM + 100 V tp = 20 µs Tj = 150 °C 4 A Tj = 150 °C 1 W - 40 to + 150 - 40 to + 150 °C Average gate power dissipation Storage junction temperature range Operating junction temperature range Electrical characteristics (Tj = 25 °C, unless otherwise specified) Symbol IGT A Test conditions VD = 12 V RL = 33 Ω Quadrant Min. Max. Unit I - II - III 1 10 mA 1.0 V I - II - III VD = VDRM, RL = 3.3 kΩ I - II - III IT = 100 mA V 25 I - III 30 II 35 IG = 1.2 IGT mA mA VD = 67% VDRM, gate open, Tj = 150 °C 75 Logic level, 0.1 V/µs, Tj = 150 °C 14.4 Logic level, 15 V/µs, Tj = 150 °C 3.8 V/µs A/ms 1. For both polarities of A2 referenced to A1. 2/10 0.15 Doc ID 15715 Rev 1 T1010H Characteristics Table 4. Static characteristics Symbol VT (1) Test conditions Value Unit ITM = 14.1 A, tp = 380 µs Tj = 25 °C MAX. 1.5 V Vt0 (1) Threshold voltage Tj = 150 °C MAX. 0.80 V Rd (1) Dynamic resistance Tj = 150 °C MAX. 41.0 mΩ Tj = 25 °C MAX. 5 µA Tj = 150 °C MAX. 3.6 VD/VR = 400 V (at peak mains voltage) Tj = 150 °C MAX. 3.0 VD/VR = 200 V (at peak mains voltage) Tj = 150 °C MAX. 2.5 VDRM = VRRM IDRM IRRM mA 1. for both polarities of A2 referenced to A1. Table 5. Thermal resistance Symbol Parameter D2PAK / TO-220AB Junction to case (AC) Rth(j-c) S=1 Rth(j-a) Figure 1. Value cm2 Unit 1.50 D2PAK 45 TO-220AB 60 °C/W Junction to ambient Maximum power dissipation versus Figure 2. on-state rms current (full cycle) P(W) On-state rms current versus case temperature (full cycle) IT(RMS)(A) 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 TC(°C) 1 IT(RMS)(A) 0 0 0 1 2 3 4 5 6 7 8 9 10 0 Doc ID 15715 Rev 1 25 50 75 100 125 150 3/10 Characteristics Figure 3. T1010H On-state rms current versus ambient temperature (free air convection, (full cycle) Figure 4. Relative variation of thermal impedance, versus pulse duration K=[Zth/Rth] IT(RMS)(A) 1.E+00 3.0 Zth(j-c) 2.5 1.E-01 2.0 Zth(j-a) 1.5 1.0 1.E-02 0.5 Ta (°C) tp(s) 0.0 0 25 Figure 5. 50 75 100 125 150 1.E-03 1.E-03 1.E-02 Relative variation of gate trigger Figure 6. current and voltage versus junction temperature (typical values) IGT, VGT[T j] / IGT, VGT[T j=25 °C] 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 Relative variation of holding and latching current versus junction temperature (typical values) IH, IL [T j] / IH, IL [T j=25 °C] 2.0 2.5 IGT Q3 2.0 IH IGTQ1- Q2 1.5 IL 1.5 1.0 VGT Q1 - Q2- Q3 1.0 0.5 0.5 Tj(°C) Tj(°C) 0.0 0.0 -50 Figure 7. -25 0 25 50 75 100 125 150 -50 -25 Surge peak on-state current versus Figure 8. number of cycles 0 25 50 75 100 125 150 Non-repetitive surge peak on-state current and corresponding value of I2t ITSM (A), I²t (A²s) ITSM(A) 1000 110 Tj initial=25 °C 100 90 One cycle Non repetitive Tj initial=25 °C 70 ITSM dI/dt limitation: 50 A/µs t=20ms 80 100 60 I²t 50 40 10 30 Repetitive TC=135 °C 20 10 Sinusoidal pulse width tp < 10 ms Number of cycles 0 1 4/10 tP(ms) 1 10 100 1000 0.01 Doc ID 15715 Rev 1 0.10 1.00 10.00 T1010H Characteristics Figure 9. On-state characteristics (maximum Figure 10. Relative variation of critical rate of values) decrease of main current versus junction temperature ITM (A) (dI/dt)C [T j] / (dI/dt)c [T j=150 °C] 100 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Tj max : Vto = 0.80 V Rd = 41 mΩ Tj=150 °C 10 Tj=25 °C VTM (V) 1 0 1 2 3 4 50 75 100 125 150 Figure 12. Relative variation of static dV/dt immunity versus junction temperature dV/dt [T j] / dV/dt [T j=150 °C] (dI/dt)c [ (dV/dt)c ] / Specified (dI/dt)c 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 4 3 2 1 (dV/dt)C (V/µs) 0 0.1 25 5 Figure 11. Relative variation of critical rate of decrease of main current versus reapplied dV/dt (typical values) T j(°C) 1.0 10.0 100.0 VD=VR=400 V T j(°C) 25 50 75 100 125 150 Figure 13. Variation of leakage current versus Figure 14. Acceptable case to ambient thermal junction temperature for different resistance versus repetitive peak values of blocking voltage off-state voltage IDRM/IRRM [Tj;V DRM/ VRRM]/IDRM/IRRM [Tj=150°C; 600V] Rth(c-a) (°C/W) 1.0E+00 45 VDRM=VRRM=600 V Rth(j-c)=1.5 °C/W TJ=150 °C 40 35 1.0E-01 VDRM=VRRM=400 V 30 25 VDRM=VRRM=200 V 1.0E-02 20 15 1.0E-03 10 5 T j(°C) 25 50 75 VAC PEAK(V) 0 1.0E-04 100 125 150 200 Doc ID 15715 Rev 1 300 400 500 600 5/10 Ordering information scheme 2 T1010H Ordering information scheme Figure 15. Ordering information scheme T 10 10 H - 6 y Triac series Current 10 = 10 A Sensitivity 10 = 10 mA High temperature Voltage 6 = 600 V Package G = D2PAK T = TO-220AB Packing Blank = Tube (D2PAK, TO-220AB) -TR = Tape and reel (D2PAK) 6/10 Doc ID 15715 Rev 1 -TR T1010H 3 Package information Package information ● Epoxy meets UL94, V0 ● Recommended torque 0.4 to 0.6 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 6. D2PAK dimensions Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Typ. Max. A 4.30 4.60 0.169 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.70 0.93 0.027 0.037 B2 1.25 C 0.45 0.60 0.017 0.024 C2 1.21 1.36 0.047 0.054 D 8.95 9.35 0.352 0.368 E 10.00 10.28 0.393 0.405 G 4.88 5.28 0.192 0.208 L 15.00 15.85 0.590 0.624 L2 1.27 1.40 0.050 0.055 L3 1.40 1.75 0.055 0.069 A E C2 L2 D L L3 1.40 0.048 0.055 A1 B2 R C B G A2 2mm min. FLAT ZONE V2 R 0.40 V2 0° 0.016 8° 0° 8° Figure 16. Footprint (dimensions in mm) 16.90 10.30 5.08 1.30 8.90 Doc ID 15715 Rev 1 3.70 7/10 Package information Table 7. T1010H TO-220AB dimensions Dimensions Ref. Millimeters Min. A 15.20 a1 C B ØI F A I4 Max. Min. Typ. 15.90 0.598 3.75 Max. 0.625 0.147 a2 13.00 14.00 0.511 0.551 B 10.00 10.40 0.393 0.409 b1 0.61 0.88 0.024 0.034 b2 1.23 1.32 0.048 0.051 C 4.40 4.60 0.173 0.181 c1 0.49 0.70 0.019 0.027 c2 2.40 2.72 0.094 0.107 e 2.40 2.70 0.094 0.106 F 6.20 6.60 0.244 0.259 ØI 3.75 3.85 0.147 0.151 I4 15.80 16.40 16.80 0.622 0.646 0.661 L 2.65 2.95 0.104 0.116 l2 1.14 1.70 0.044 0.066 l3 1.14 1.70 0.044 0.066 b2 L Typ. Inches l3 c2 a1 l2 a2 M b1 e c1 M 8/10 Doc ID 15715 Rev 1 2.60 0.102 T1010H 4 Ordering information Ordering information Table 8. 5 Ordering information Order code Marking Package Weight Base qty Delivery mode T1010H-6G T1010H 6G D2PAK 1.5 g 50 Tube T1010H-6G-TR T1010H 6G D2 1.5 g 1000 Tape and reel T1010H-6T T1010H 6T 2.3 g 50 Tube PAK TO-220AB Revision history Table 9. Document revision history Date Revision 15-May-2009 1 Changes First issue. Doc ID 15715 Rev 1 9/10 T1010H Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 10/10 Doc ID 15715 Rev 1