T1010H

T1010H High temperature 10 A sensitive TRIACs Features ■ ■ ■ ■ ■ A2 Medium current TRIAC Logic level sensitive TRIAC 150 °C max. Tj turn-off commutation Clip bounding RoHS (2002/95/EC) compliant packages A2 G A1 Applications ■ ■ A2 The T1010H is designed for the control of AC actuators in appliances and industrial systems. The multi-port drive of the microcontroller can control the multiple loads of such appliances and systems through these sensitive gate TRIACs. A2 A1 G A2 A1 G D2PAK T1010H-6G TO-220AB T1010H-6T Description Specifically designed to operate at 150 °C, the new 10 A T1010H TRIACs provide an enhanced performance in terms of power loss and thermal dissipation. This allows the optimization of the heatsink size, leading to space and cost effectiveness when compared to electromechanical solutions. Based on ST logic level technology, they offer an IGT lower than 10 mA and specified minimal commutation and high noise immunity levels valid up to the Tj max. Table 1. Symbol IT(RMS) Device summary Value 10 600 10 Unit A V mA VDRM/VRRM IGT MAX May 2009 Doc ID 15715 Rev 1 1/10 www.st.com 10 Characteristics T1010H 1 Table 2. Symbol IT(RMS) ITSM I²t dI/dt VDSM/VRSM IGM PG(AV) Tstg Tj Characteristics Absolute maximum ratings Parameter On-state rms current (full sine wave) Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) I²t Value for fusing Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns Non repetitive surge peak off-state voltage Peak gate current Average gate power dissipation Storage junction temperature range Operating junction temperature range D2PAK, TO-220AB F = 60 Hz F = 50 Hz tp = 10 ms F = 120 Hz tp = 10 ms tp = 20 µs Tj = 150 °C Tj = 25 °C Tj = 150 °C Tj = 150 °C Tc = 135 °C t = 16.7 ms t = 20 ms Value 10 105 A 100 66 50 VDRM/VRRM + 100 4 1 - 40 to + 150 - 40 to + 150 A ²s A/µs V A W °C Unit A Table 3. Symbol IGT VGT VGD IH (1) Electrical characteristics (Tj = 25 °C, unless otherwise specified) Test conditions VD = 12 V RL = 33 Ω VD = VDRM, RL = 3.3 kΩ IT = 100 mA I - III IG = 1.2 IGT VD = 67% VDRM, gate open, Tj = 150 °C Logic level, 0.1 V/µs, Tj = 150 °C Logic level, 15 V/µs, Tj = 150 °C Quadrant I - II - III I - II - III I - II - III 0.15 25 30 mA II 75 14.4 A/ms 3.8 35 V/µs Min. 1 Max. 10 1.0 Unit mA V V mA IL dV/dt (1) (dI/dt)c (1) 1. For both polarities of A2 referenced to A1. 2/10 Doc ID 15715 Rev 1 T1010H Table 4. Symbol VT (1) Vt0 Rd (1) (1) Characteristics Static characteristics Test conditions ITM = 14.1 A, tp = 380 µs Threshold voltage Dynamic resistance VDRM = VRRM Tj = 25 °C Tj = 150 °C Tj = 150 °C Tj = 25 °C Tj = 150 °C MAX. MAX. MAX. MAX. MAX. MAX. MAX. Value 1.5 0.80 41.0 5 3.6 3.0 2.5 mA Unit V V mΩ µA IDRM IRRM VD/VR = 400 V (at peak mains voltage) Tj = 150 °C VD/VR = 200 V (at peak mains voltage) Tj = 150 °C 1. for both polarities of A2 referenced to A1. Table 5. Symbol Rth(j-c) Rth(j-a) Thermal resistance Parameter Junction to case (AC) S=1 Junction to ambient TO-220AB 60 cm2 D2PAK / TO-220AB D2PAK Value 1.50 45 °C/W Unit Figure 1. P(W) 12 11 10 9 8 7 6 5 4 3 2 1 0 0 1 Maximum power dissipation versus Figure 2. on-state rms current (full cycle) IT(RMS)(A) 12 11 10 9 8 7 6 5 4 3 2 IT(RMS)(A) 2 3 4 5 6 7 8 9 10 On-state rms current versus case temperature (full cycle) 1 0 0 25 50 TC(°C) 75 100 125 150 Doc ID 15715 Rev 1 3/10 Characteristics T1010H Figure 3. On-state rms current versus ambient temperature (free air convection, (full cycle) Figure 4. Relative variation of thermal impedance, versus pulse duration IT(RMS)(A) 3.0 2.5 2.0 1.5 1.0 0.5 Ta (°C) 0.0 0 25 50 75 100 125 150 K=[Zth/Rth] 1.E+00 Zth(j-c) 1.E-01 Zth(j-a) 1.E-02 tp(s) 1.E-03 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03 Figure 5. Relative variation of gate trigger Figure 6. current and voltage versus junction temperature (typical values) 2.0 IGT Q3 Relative variation of holding and latching current versus junction temperature (typical values) IGT, VGT[T j] / IGT, VGT[T j=25 °C] 2.5 IH, IL [T j] / IH, IL [T j=25 °C] 2.0 IGTQ1- Q2 1.5 1.5 IH IL 1.0 1.0 VGT Q1 - Q2- Q3 0.5 0.5 Tj(°C) 0.0 -50 -25 0 25 50 75 100 125 150 Tj(°C) 0.0 -50 -25 0 25 50 75 100 125 150 Figure 7. Surge peak on-state current versus Figure 8. number of cycles Non-repetitive surge peak on-state current and corresponding value of I2t Tj initial=25 °C dI/dt limitation: 50 A/µs ITSM ITSM(A) 110 100 90 80 70 60 50 40 30 20 10 0 1 10 100 1000 Repetitive TC=135 °C Non repetitive Tj initial=25 °C t=20ms ITSM (A), I²t (A²s) 1000 One cycle 100 I²t 10 Number of cycles Sinusoidal pulse width tp < 10 ms tP(ms) 1.00 10.00 1 0.01 0.10 4/10 Doc ID 15715 Rev 1 T1010H Characteristics Figure 9. On-state characteristics (maximum Figure 10. Relative variation of critical rate of values) decrease of main current versus junction temperature (dI/dt)C [T j] / (dI/dt)c [T j=150 °C] 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 3 4 5 ITM (A) 100 Tj max : Vto = 0.80 V Rd = 41 mΩ 10 Tj=150 °C Tj=25 °C VTM (V) 1 0 1 2 T j(°C) 25 50 75 100 125 150 Figure 11. Relative variation of critical rate of decrease of main current versus reapplied dV/dt (typical values) (dI/dt)c [ (dV/dt)c ] / Specified (dI/dt)c 4 Figure 12. Relative variation of static dV/dt immunity versus junction temperature dV/dt [T j] / dV/dt [T j=150 °C] 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 VD=VR=400 V 3 2 1 (dV/dt)C (V/µs) 0 0.1 1.0 10.0 100.0 T j(°C) 25 50 75 100 125 150 Figure 13. Variation of leakage current versus Figure 14. Acceptable case to ambient thermal junction temperature for different resistance versus repetitive peak values of blocking voltage off-state voltage IDRM/IRRM [Tj;V DRM/ VRRM]/IDRM/IRRM [Tj=150°C; 600V] Rth(c-a) (°C/W) 45 Rth(j-c)=1.5 °C/W TJ=150 °C 1.0E+00 VDRM=VRRM=600 V 40 35 1.0E-01 VDRM=VRRM=400 V 30 25 20 15 1.0E-02 VDRM=VRRM=200 V 1.0E-03 10 5 VAC PEAK(V) 300 400 500 600 T j(°C) 1.0E-04 25 50 75 100 125 150 0 200 Doc ID 15715 Rev 1 5/10 Ordering information scheme T1010H 2 Ordering information scheme Figure 15. Ordering information scheme T 10 10 H - 6 y Triac series Current 10 = 10 A Sensitivity 10 = 10 mA High temperature Voltage 6 = 600 V Package G = D2PAK T = TO-220AB Packing Blank = Tube (D2PAK, TO-220AB) -TR = Tape and reel (D2PAK) -TR 6/10 Doc ID 15715 Rev 1 T1010H Package information 3 Package information ● ● Epoxy meets UL94, V0 Recommended torque 0.4 to 0.6 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 6. D2PAK dimensions Dimensions Ref. Millimeters Min. A A E L2 Inches Min. 0.169 0.098 0.001 0.027 0.048 0.055 Typ. Max. 0.181 0.106 0.009 0.037 Typ. Max. 4.60 2.69 0.23 0.93 4.30 2.49 0.03 0.70 1.25 0.45 1.21 8.95 10.00 4.88 15.00 1.27 1.40 0.40 0° 1.40 A1 C2 A2 B D L L3 A1 B2 C C2 B2 B G A2 2mm min. FLAT ZONE C R 0.60 1.36 9.35 0.017 0.047 0.352 0.024 0.054 0.368 0.405 0.208 0.624 0.055 0.069 0.016 D E G L 10.28 0.393 5.28 0.192 15.85 0.590 1.40 1.75 0.050 0.055 V2 L2 L3 R V2 8° 0° 8° Figure 16. Footprint (dimensions in mm) 16.90 10.30 1.30 5.08 8.90 3.70 Doc ID 15715 Rev 1 7/10 Package information Table 7. TO-220AB dimensions Dimensions Ref. Millimeters Min. A a1 B ØI L F A I4 l3 a1 l2 c2 b2 C T1010H Inches Min. Typ. Max. 0.625 0.147 Typ. Max. 15.20 3.75 13.00 10.00 0.61 1.23 4.40 0.49 2.40 2.40 6.20 3.75 15.90 0.598 a2 B b1 b2 C c1 c2 14.00 0.511 10.40 0.393 0.88 1.32 4.60 0.70 2.72 2.70 6.60 3.85 0.024 0.048 0.173 0.019 0.094 0.094 0.244 0.147 0.551 0.409 0.034 0.051 0.181 0.027 0.107 0.106 0.259 0.151 a2 e M b1 e c1 F ØI I4 L l2 l3 M 15.80 16.40 16.80 0.622 0.646 0.661 2.65 1.14 1.14 2.60 2.95 1.70 1.70 0.104 0.044 0.044 0.102 0.116 0.066 0.066 8/10 Doc ID 15715 Rev 1 T1010H Ordering information 4 Ordering information Table 8. Ordering information Marking T1010H 6G T1010H 6G T1010H 6T Package D2PAK D2 PAK Weight 1.5 g 1.5 g 2.3 g Base qty 50 1000 50 Delivery mode Tube Tape and reel Tube Order code T1010H-6G T1010H-6G-TR T1010H-6T TO-220AB 5 Revision history Table 9. Date 15-May-2009 Document revision history Revision 1 First issue. Changes Doc ID 15715 Rev 1 9/10 T1010H Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 10/10 Doc ID 15715 Rev 1