T1050H-6T

T1035H, T1050H High temperature 10 A Snubberless™ Triacs Features A2 ■ Medium current Triac ■ 150 °C max. Tj turn-off commutation ■ Low thermal resistance with clip bonding ■ Very high 3 quadrant commutation capability ■ Packages are RoHS (2002/95/EC) compliant ■ UL certified (ref. file E81734) G A2 A1 A2 A2 G G A2 A1 A1 Applications Especially designed to operate in high power density or universal motor applications such as vacuum cleaner and washing machine drum motor, these 10 A Triacs provide a very high switching capability up to junction temperatures of 150 °C. D2PAK T10xxH-6G TO-220AB T10xxH-6T G The heatsink can be reduced, compared to traditional Triacs, according to the high performance at given junction temperatures. A2 A1 TO-220AB Insulated T10xxH-6I Description Available in through-hole or surface mount packages, the T1035H and T1050H Triacs series are suitable for general purpose mains power ac switching. By using an internal ceramic pad, the T10xxH-6I provides voltage insulation (rated at 2500 V rms). Table 1. Device summary Symbol Value Unit IT(RMS) 10 A VDRM/VRRM 600 V IGT 35 or 50 mA TM: Snubberless is a trademark of STMicroelectronics September 2011 Doc ID 13565 Rev 2 1/10 www.st.com 10 Characteristics T1035H, T1050H 1 Characteristics Table 2. Absolute maximum ratings Symbol Parameter IGM PG(AV) Tstg Tj Table 3. A TO-220AB Ins Tc = 125 °C Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) F = 50 Hz t = 20 ms 100 F = 60 Hz t = 16.7 ms 105 I²t Value for fusing tp = 10 ms Critical rate of rise of on-state current IG = 2 x IGT , tr ≤ 100 ns F = 120 Hz Non repetitive surge peak off-state voltage Peak gate current ITSM VDSM/VRSM 10 Tc = 135 °C On-state rms current (full sine wave) dI/dt Unit D2PAK, TO-220AB IT(RMS) I ²t Value A 66 A²s Tj = 150 °C 50 A/µs tp = 10 ms Tj = 25 °C VDRM/VRRM + 100 V tp = 20 µs Tj = 150 °C 4 A Tj = 150 °C 1 W - 40 to + 150 - 40 to + 150 °C Average gate power dissipation Storage junction temperature range Operating junction temperature range Electrical characteristics (Tj = 25 °C, unless otherwise specified) Value Symbol Test Conditions Quadrant Unit T1035H T1050H IGT (1) VGT VD = 12 V, RL = 33 Ω VGD VD = VDRM, RL = 3.3 kΩ IH (2) IT = 500 mA IL IG = 1.2 IGT I - II - III MAX. I - II - III MAX. 1.0 V I - II - III MIN. 0.15 V MAX. I - III dV/dt (2) (dI/dt)c (2) 50 35 75 50 90 80 110 MAX. II mA mA mA VD = 67% VDRM, gate open, Tj = 150 °C MIN. 1000 1500 V/µs Without snubber, Tj = 150 °C MIN. 13 18 A/ms 1. minimum IGT is guaranted at 20% of IGT max. 2. for both polarities of A2 referenced to A1. 2/10 35 Doc ID 13565 Rev 2 T1035H, T1050H Table 4. Static characteristics Symbol VT (1) Characteristics Test Conditions Value Unit ITM = 14 A, tp = 380 µs Tj = 25 °C MAX. 1.5 V Vt0 (1) Threshold voltage Tj = 150 °C MAX. 0.80 V Rd (1) Dynamic resistance Tj = 150 °C MAX. 34 mΩ Tj = 25 °C MAX. 5 µA Tj = 150 °C MAX. 3.6 VD/VR = 400 V (at peak mains voltage) Tj = 150 °C MAX. 3.0 VD/VR = 200 V (at peak mains voltage) Tj = 150 °C MAX. 2.5 VDRM = VRRM IDRM IRRM (2) mA 1. for both polarities of A2 referenced to A1. 2. tp = 380 µs Table 5. Thermal resistance Symbol Rth(j-c) Parameter D2PAK / TO-220AB 1.45 TO-220AB Ins 3.4 D2PAK 45 TO-220AB / TO-220AB Ins 60 Unit Junction to case (AC) S=1 Rth(j-a) Value cm2 °C/W Junction to ambient Doc ID 13565 Rev 2 3/10 Characteristics Figure 1. T1035H, T1050H Maximum power dissipation versus Figure 2. on-state rms current (full cycle) On-state rms current versus case temperature (full cycle) IT(RMS) (A) P(W) 11 12 α=180 ° 10 TO-220AB/D²PAK 10 9 TO-220AB Insulated 8 8 7 6 6 5 4 4 3 180° 2 2 α=180 ° 1 IT(RMS)(A) 0 0 1 2 Figure 3. 3 4 5 6 7 8 9 10 On-state rms current versus ambient temperature 0 25 Figure 4. IT(RMS) (A) 1.0E+02 4.5 50 75 100 125 150 Variation of thermal impedance versus pulse duration Zth(°C/W) α=180 ° D²PAK SCU=1 cm² Epoxy printed circuit board FR4, copper thickness = 35 µm 4.0 TC(°C) 0 Zth(j-a) 3.5 1.0E+01 3.0 2.5 Zth(j-c) 2.0 1.0E+00 1.5 1.0 0.5 Tamb(°C) 0.0 0 25 Figure 5. 100 50 tP(s) 1.0E-01 75 100 125 1.0E-03 150 On-state characteristics (maximum values) Figure 6. ITM(A) 110 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 Surge peak on-state current versus number of cycles ITSM (A) 100 90 Tj=150 °C t=20ms Non repetitive Tj initial=25 °C 80 One cycle 70 60 Tj=25 °C 10 50 Repetitive Tc=125 °C 40 30 Tj max. : Vt0 = 0.80 V Rd = 34 mΩ 20 10 VTM(V) 0.0 4/10 0.5 1.0 1.5 2.0 2.5 Number of cycles 0 1 3.0 3.5 4.0 4.5 5.0 1 Doc ID 13565 Rev 2 10 100 1000 T1035H, T1050H Figure 7. 10000 Characteristics Non-repetitive surge peak on-state Figure 8. current for a sinusoidal pulse with Relative variation of IGT,IH, IL vs junction temperature (typical values) IGT, IH, IL [T j] / IGT, IH, IL [T j=25°C] ITSM(A), I²t (A²s) 2.5 Tj initial=25 °C dI/dt limitation: 50 A/µs IGT 2.0 1000 1.5 ITSM IH & IL 1.0 100 I²t 0.5 2 10 0.01 Figure 9. 2.0 0.10 Tj(°C) tP(ms) width tp < 10 ms and corresponding value of I t 1.00 0.0 -40 10.00 Relative variation of critical rate of decrease of main current (dI/dt)c versus reapplied (dV/dt)c -20 0 20 40 60 80 100 120 140 160 Figure 10. Relative variation of critical rate of decrease of main current versus junction temperature (dI/dt)c [T j] / (dI/dt)c [T j=150°C] (dI/dt)c [ (dV/dt) c ] / Specified (dI/dt) c 8 typical values 1.8 7 1.6 6 1.4 1.2 5 1.0 4 0.8 3 0.6 2 0.4 1 0.2 (dV/dt)C (V/µs) 0.0 0.1 1.0 100.0 Figure 11. Leakage current versus junction temperature for different values of blocking voltage (typical values) 1.0E+04 T j(°C) 0 10.0 25 50 75 100 125 150 Figure 12. Variation of thermal resistance junction to ambient versus copper surface under tab Rth(j-a) (°C/W) IDRM/IRRM(µA) 80 1.0E+03 Epoxy printed circuit board FR4, copper thickness = 35 µm 70 VDRM=VRRM=600 V D²PAK 60 VDRM=VRRM=400 V 50 1.0E+02 VDRM=VRRM=200 V 40 1.0E+01 30 20 1.0E+00 10 SCU(cm²) T j(°C) 1.0E-01 0 50 75 100 125 150 0 Doc ID 13565 Rev 2 5 10 15 20 25 30 35 40 5/10 Ordering information scheme 2 T1035H, T1050H Ordering information scheme Figure 13. Ordering information scheme T 10 xx H - 6 y Triac series Current 10 = 10 A Sensitivity 35 = 35 mA 50 = 50 mA High temperature Voltage 6 = 600 V Package G = D2PAK T = TO-220AB I = TO-220AB Ins Packing Blank = Tube (D2PAK, TO-220AB) -TR = Tape and reel (D2PAK) 6/10 Doc ID 13565 Rev 2 -TR T1035H, T1050H 3 Package information Package information ● Epoxy meets UL94, V0 ● Recommended torque 0.4 to 0.6 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 6. D2PAK dimensions Dimensions Ref. Millimeters Min. A E C2 L2 D L Typ. Inches Max. Min. Typ. Max. A 4.30 4.60 0.169 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.70 0.93 0.027 0.037 B2 1.25 C 0.45 0.60 0.017 0.024 C2 1.21 1.36 0.047 0.054 D 8.95 9.35 0.352 0.368 E 10.00 10.28 0.393 0.405 G 4.88 5.28 0.192 0.208 L 15.00 15.85 0.590 0.624 L2 1.27 1.40 0.050 0.055 L3 1.40 1.75 0.055 0.069 L3 1.40 0.048 0.055 A1 B2 R C B G A2 2mm min. FLAT ZONE V2 R V2 0.40 0° 0.016 8° 0° 8° Figure 14. Footprint (dimensions in mm) 16.90 10.30 5.08 1.30 8.90 Doc ID 13565 Rev 2 3.70 7/10 Package information Table 7. T1035H, T1050H TO-220AB and TO-220AB Ins dimensions Dimensions Ref. Millimeters Min. A 15.20 a1 C B ØI Typ. Max. Inches Min. Typ. 15.90 0.598 3.75 Max. 0.625 0.147 a2 13.00 14.00 0.511 0.551 B 10.00 10.40 0.393 0.409 b1 0.61 0.88 0.024 0.034 b2 1.23 1.32 0.048 0.051 C 4.40 4.60 0.173 0.181 c1 0.49 0.70 0.019 0.027 c2 2.40 2.72 0.094 0.107 e 2.40 2.70 0.094 0.106 F 6.20 6.60 0.244 0.259 ØI 3.75 3.85 0.147 0.151 I4 15.80 16.40 16.80 0.622 0.646 0.661 L 2.65 2.95 0.104 0.116 l2 1.14 1.70 0.044 0.066 l3 1.14 1.70 0.044 0.066 b2 L F A I4 l3 c2 a1 l2 a2 M b1 c1 e M 8/10 Doc ID 13565 Rev 2 2.60 0.102 T1035H, T1050H 4 Ordering information Ordering information Table 8. 5 Ordering information Order code Marking Package Weight Base qty Delivery mode T10xxH-6G T10xxH 6G D2PAK 1.5 g 50 Tube T10xxH-6G-TR T10xxH 6G D2 1.5 g 1000 Tape and reel T10xxH-6T T10xxH 6T TO-220AB 2.3 g 50 Tube T10xxH-6I T10xxH 6I TO-220AB Ins 2.3 g 50 Tube PAK Revision history Table 9. Document revision history Date Revision Changes 17-Apr-2007 1 First issue 20-Sep-2011 2 Updated: Features, Description and Figure 2. Doc ID 13565 Rev 2 9/10 T1035H, T1050H Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2011 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 10/10 Doc ID 13565 Rev 2