T2035T-8G

T2035T-8G Datasheet 20 A 800 V D2PAK Snubberless™ Triac Features A2 A1 A2 • • • • • High static dV/dt High dynamic turn-off commutation (dl/dt)c 150 °C maximum junction temperature Three quadrants Surge capability VDSM, VRSM = 900 V • Benefits: – High immunity to false turn-on thanks to high static dV/dt – Better turn-off in high temperature environments thanks to (dI/dt)c – Increase of thermal margin due to extended working Tj up to 150 °C G D²PAK – Good thermal resistance due to non-insulated tab. A2 Applications A2: Anode2 A1: Anode1 G: Gate G A1 • • • • • • • General purpose AC line load switching Motor control circuits Home appliances Heating Lighting Inrush current limiting circuits Overvoltage crowbar protection Product status link Description T2035T-8G Product summary Available in SMD, the T2035T-8G Triac can be used for the on/off or phase angle control function in general purpose AC switching where high commutation capability is required. The T2035T-8G can be used without a snubber RC circuit when the limits defined are respected. IT(RMS) 20 A VDRM/VRRM 800 V D2PAK package is UL-94,V0 flammability resin compliance. VDSM/VRSM 900 V IGT 35 mA Package environmentally friendly Ecopack®2 graded (RoHS and Halogen Free compliance). Snubberless™ is a trademark of STMicroelectronics. DS12739 - Rev 1 - September 2018 For further information contact your local STMicroelectronics sales office. www.st.com T2035T-8G Characteristics 1 Characteristics Table 1. Absolute maximum ratings (limiting values) Symbol IT(RMS) ITSM I2t dl/dt Parameter 20 Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C tp = 20 ms 160 tp = 16.7 ms 168 I2t value for fusing tp = 10 ms 169 A2s Critical rate of rise of on-state current, IG = 2 x IGT, tr ≤ 100 ns Tj initial = 150 °C, f = 100 Hz 100 A/µs Tj = 125 °C 800 V Tj = 150 °C 600 V tp = 10 ms, Tj = 25 °C 900 V 4 A 5 V 1 W Storage junction temperature range -40 to +150 °C Operating junction temperature range -40 to +150 °C IGM Peak gate current VGM Peak Gate Voltage Tj A Tc = 122 °C VDSM/VRSM Non Repetitive peak off-state voltage Tstg Unit RMS on-state current (full sine wave) VDRM/VRRM Repetitive peak off-state voltage (50-60 Hz) PG(AV) Value tp = 20 µs, Tj = 150 °C Tj = 150 °C Average gate power dissipation A Table 2. Electrical characteristics (Tj = 25 °C, unless otherwise specified) Symbol (1) Quadrants; Tj Test conditions Value Unit VD = 12 V, RL = 30 Ω I - II - III Max. 35 mA VGT VD = 12 V, RL = 30 Ω I - II - III Max. 1.0 V VGD VD = 600 V, RL = 3.3 kΩ I - II - III Max. 0.15 V I - III Max. 50 mA II Max. 80 mA Max. 45 mA IGT IL IH (2) dV/dt (2) (dl/dt)c (2) IG = 1.2 x IGT Tj = 150 °C IT = 500 mA, gate open VD = 536 V, gate open Tj = 125 °C Min. 1500 V/µs VD = 402 V, gate open Tj = 150 °C Min. 1000 V/µs Tj = 125 °C Min. 27.5 A/ms Tj = 150 °C Min. 17.5 A/ms Without snubber 1. Minimum IGT is guaranteed at 5% of IGT max 2. For both polarities of A2 referenced to A1. DS12739 - Rev 1 page 2/12 T2035T-8G Characteristics Table 3. Static characteristics Symbol Test conditions Value Unit Max. 1.50 V 150 °C Max. 0.85 V 150 °C Max. 22 mΩ 5 µA 1.7 mA 4.1 mA VTM (1) IT = 28.2 A, tp = 380 µs 25 °C VTO (1) Threshold on-state voltage Dynamic resistance RD (1) IDRM/IRRM 25 °C VDRM = VRRM = 800 V Max. 125°C VDRM = VRRM = 600 V 150 °C Max. 1. For both polarities of A2 referenced to A1. Table 4. Thermal resistance Symbol Rth(j-c) DS12739 - Rev 1 Parameter Junction to case (AC) D²PAK Max. Value Unit 1.15 °C/W page 3/12 T2035T-8G Characteristics (curves) 1.2 Characteristics curves Figure 1. Maximum power dissipation versus on-state RMS current Figure 2. On-state RMS current versus case temperature IT(RMS)(A) P(W) 22 26 20 24 α = 180° 22 18 20 16 18 14 16 12 14 α = 180° 10 12 8 10 6 8 4 6 180° 4 IT(RMS)(A) 2 Tc(°C) 2 0 0 0 0 2 4 6 8 10 12 14 16 18 25 50 75 100 125 150 20 Figure 3. On-state RMS current versus ambient temperature (free air convection) Figure 4. Relative variation of thermal impedance versus pulse duration K = [Zth/Rth] IT(RMS)(A) 1.0E+00 4.0 α = 180° Zth(j-c) 3.5 3.0 2.5 1.0E-01 2.0 1.5 1.0 Ta(°C) 0.5 tp(s) 0.0 0 DS12739 - Rev 1 25 50 75 100 125 150 1.0E-02 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 page 4/12 T2035T-8G Characteristics (curves) Figure 5. Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values) IGT, IH, IL [Tj] / IGT, IH, IL [Tj = 25 °C] Figure 6. Surge peak on-state current versus number of cycles ITSM(A) 180 2.5 160 2.0 t=20ms 140 IGT 120 1.5 One cy cle Non repetitive Tj initial = 25 °C 100 IH and IL 80 60 1.0 Repetitive Tc = 122°C 40 0.5 20 Tj (°C) Number of cycles 0 0.0 1 -40 -20 0 20 40 60 80 100 120 140 10 100 1000 160 Figure 7. Non repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms Figure 8. On-state characteristics (maximum values) ITM(A) ITSM(A) 1000 Tj max. Vto = 0.85 V Rd = 22 mΩ 10000 Tj initial = 25 °C dl/dt limitation: 100 A/µs 100 1000 Tj = 150 °C 10 ITSM Tj = 25 °C VTM(V) tP(ms) 100 0.01 1 0.10 1.00 0.0 10.00 Figure 9. Relative variation of critical rate of decrease of main current versus junction temperature 0.5 1.0 1.5 2.5 2.0 3.0 3.5 Figure 10. Relative variation of critical rate of decrease of main current versus reapplied (dV/dt)c (typical values) (dl/dt)c [Tj] / (dl/dt)c [Tj = 150 °C] (dl/dt)c [(dV/dt)c] / specified (dl/dt)c 8 2.0 7 1.8 6 1.6 1.4 5 1.2 4 1.0 3 0.8 2 0.6 0.4 1 0.2 Tj(°C) 0 25 DS12739 - Rev 1 50 75 100 125 150 (dV/dt)c (V/µs) 0.0 0.1 1.0 10.0 100.0 page 5/12 T2035T-8G Characteristics (curves) Figure 11. Relative variation of leakage current versus junction temperature for different values of blocking voltage (typical values) Figure 12. Thermal resistance junction to ambient versus copper surface under tab Rth(j-a) (°C/W) IDRM, IRRM at [ Tj ] / IDRM, IRRM at [Tj max.]* 80 1.0E+00 Epoxy printed circuit board FR4, eCu = 35 µm D²PAK 70 1.0E-01 60 VDRM = VRRM = 800 V 50 1.0E-02 40 VDRM = VRRM = 600 V 1.0E-03 30 20 1.0E-04 *[Tj max = 125 °C; VDRM, VRRM = 800 V] [Tj max = 150 °C; VDRM, VRRM = 600 V] SCu (cm²) 10 Tj(°C) 1.0E-05 0 0 25 DS12739 - Rev 1 50 75 100 125 5 10 15 20 25 30 35 40 150 page 6/12 T2035T-8G Package information 2 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 D²PAK package information • • • ECOPACK®2compliant Lead-free package leads finishing Molding compound resin is halogen-free and meets UL94 standard level V0 Figure 13. D²PAK package outline A E E1 E2 H D D1 L2 c2 2 3 D2 L3 1 b2 b e Max resin gate protrusion: 0.5 mm (1) G A1 A2 A3 L R Gauge Plane V2 c (1) Resin gate is accepted in each of position shown on the drawing, or their symmetrical. DS12739 - Rev 1 page 7/12 T2035T-8G D²PAK package information Table 5. D²PAK package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. A 4.30 4.60 0.1693 0.1811 A1 2.49 2.69 0.0980 0.1059 A2 0.03 0.23 0.0012 A3 0.25 0.0091 0.0098 b 0.70 0.93 0.0276 0.0366 b2 1.25 1.7 0.0492 0.0669 c 0.45 0.60 0.0177 0.0236 c2 1.21 1.36 0.0476 0.0535 D 8.95 9.35 0.3524 0.3681 D1 7.50 8.00 0.2953 0.3150 D2 1.30 1.70 0.0512 0.0669 e 2.54 0.1 E 10.00 10.28 0.3937 0.4047 E1 8.30 8.70 0.3268 0.3425 E2 6.85 7.25 0.2697 0.2854 G 4.88 5.28 0.1921 0.2079 H 15 15.85 0.5906 0.6240 L 1.78 2.28 0.0701 0.0898 L2 1.27 1.40 0.0500 0.0551 L3 1.40 1.75 0.0551 0.0689 R V2(2) 0.40 0° 0.0157 8° 0° 8° 1. Dimensions in inches are given for reference only 2. Degrees DS12739 - Rev 1 page 8/12 T2035T-8G D²PAK package information Figure 14. D²PAK recommended footprint (dimensions are in mm) 16.90 10.30 5.08 1.30 8.90 3.70 Figure 15. D²PAK stencil definitions(dimensions are in mm) DS12739 - Rev 1 page 9/12 T2035T-8G Ordering information 3 Ordering information Figure 16. Ordering information scheme T 20 35 T - 8 G - TR SnubberlessTM TRIAC T = Triac Current (RMS) / Type 20 = 20 A Gate Current 35 = 35 mA Specific application T = increased (dl/dt)c and dV/dt producing reduced ITSM Voltage 8 = 800 V Package G = D²PAK Packing Blank = Tube TR = Tape and reel Table 6. Ordering information Order code T2035T-8G-TR T2035T-8G DS12739 - Rev 1 Marking Package Weight T2035T-8G D²PAK 1.6 g Base qty. Delivery mode 1000 Tape and reel 50 Tube page 10/12 T2035T-8G Revision history Table 7. Document revision history DS12739 - Rev 1 Date Version 12-Sep-2018 1 Changes Initial release. page 11/12 T2035T-8G IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2018 STMicroelectronics – All rights reserved DS12739 - Rev 1 page 12/12