T405-600B-TR

T4 series 4 A Triacs Datasheet  production data . $ * $ $ $ $ * Table 1. Main characteristics Symbol Value Unit IT(rms) 4 A VDRM, VRRM 600 to 800 V IGT 5 to 35 mA $ Table 2. Device summary $ $ * 72$% Symbol(1) ,3$. $ Marking T405-xxxB T405-xxxB-TR $ $ * T405-xxxH '3$. T405-xxxT T410-xxxB T410-xxxB-TR Features see Table 11 T410-xxxH  Three quadrants Triac T410-xxxT  600 to 800 V VDRM/VRRM T435-xxxB T435-xxxB-TR Applications T435-xxxH  General purpose AC inductive loads T435-xxxT  Motor control circuits 1. xxx = Voltage: 600 V, 700 V or 800 V (see Table 10).  Small home appliances Description Based on ST’s Snubberless / logic level technology providing high commutation performances, the T4 series is suitable for use on AC inductive loads. They are recommended for applications using universal motors, electro valves, kitchen aid equipments, power tools, and dishwashers. November 2016 This is information on a product in full production. DocID7699 Rev 9 1/15 www.st.com 15 Characteristics 1 T4 series Characteristics Table 3. Absolute maximum ratings (Tj = 25 °C unless otherwise stated) Symbol Parameter IT(rms) ITSM I ²t Value Unit A On-state rms current (full sine wave) IPAK, DPAK, TO-220AB Tc = 110 °C 4 Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) F = 50 Hz t = 20 ms 30 F = 60 Hz t = 16.7 ms 31 tp = 10 ms 5.1 A ²s A I²t value for fusing dI/dt Critical rate of rise of on-state current IG = 2 x IGT, tr ≤ 100 ns F = 120 Hz Tj = 125 °C 50 A/µs IGM Peak gate current tp = 20 µs Tj = 125 °C 4 A Tj = 125 °C 1 W - 40 to +150 - 40 to +125 °C Average gate power dissipation PG(AV) Tstg Tj Storage junction temperature range Operating junction temperature range Table 4. Electrical characteristics (Tj = 25 °C, unless otherwise stated) Value Symbol Test conditions Unit Quadrant T405 T410 T435 IGT(1) VD = 12 V, RL = 30 Ω I - II - III Max. VGT VD = 12 V, RL = 30 Ω I - II - III Max. 1.3 V VGD VD = VDRM, RL = 3.3 k Ω , Tj = 125 °C I - II - III Min. 0.2 V IH (2) IL dV/dt (2) IT = 100 mA IG = 1.2 IGT 35 10 15 35 I - III Max. 10 25 50 II Max. 15 30 60 Tj = 125 °C Min. 20 40 400 1.8 2.7 0.9 2.0 mA mA mA VD = 67% VDRM, gate open Tj = 125 °C (dV/dt)c = 10 V/µs (without snubber) Min. 2. For both polarities of A2 referenced to A1 DocID7699 Rev 9 V/µs A/ms 2.5 1. Minimum IGT is guaranteed at 5% of IGT max. 2/15 10 Max. (dV/dt)c = 0.1 V/µs (dI/dt)c (2) 5 T4 series Characteristics Table 5. Static characteristics Symbol VTM (1) Test conditions Value Unit ITM = 5.5 A, tp = 380 µs Tj = 25 °C Max. 1.56 V Vt0 (1) Threshold voltage Tj = 125 °C Max. 0.89 V Rd (1) Dynamic resistance Tj = 125 °C Max. 120 m 5 µA 1 mA IDRM IRRM Tj = 25 °C VDRM = VRRM Max. Tj = 125 °C 1. For both polarities of A2 referenced to A1 Table 6. Thermal resistance Symbol Rth(j-c) Parameter Junction to case (AC) Junction to ambient Rth(j-a) S(1) = 0.5 cm² Value Unit IPAK, DPAK,TO-220AB 2.6 °C/W DPAK 70 °C/W TO-220AB 60 °C/W IPAK 100 °C/W Junction to ambient 1. S = Copper surface under tab. DocID7699 Rev 9 3/15 Characteristics T4 series Figure 1. Maximum power dissipation versus RMS on-state current (full cycle) Figure 2. RMS on-state current versus case temperature (full cycle) P(W) , 7506 $  6  5 72$%'3$.,3$.   4  3  2  1   IT(RMS)(A) 0.0 0.5 1.0 1.5 2.0 7 & ƒ&  0 2.5 3.0 3.5  4.0 Figure 3. RMS on-state current versus ambient temperature (printed circuit board FR4, copper thickness: 35µm) (full cycle)  , 7506 $     Figure 4. Relative variation of thermal impedance versus pulse duration ( . >=WK5WK@ 5 WKMF '3$.6 FPð    5 WKMD  72$%'3$.,3$.  (    '3$.,3$.      W S V ( 7 D ƒ&    (  Figure 5. On-state characteristics (maximum values) ( ( ( ( ( Figure 6. Surge peak on-state current versus number of cycles ITM(A) ITSM(A) 30.0 35 Tj max. Vto = 0.90V Rd = 120 mΩ 10.0 30 t=20ms 25 One cycle 20 Non repetitive Tj initial=25°C Tj = Tj max. 15 1.0 Tj = 25°C. Repetitive TC=110°C 10 5 VTM(V) Number of cycles 0 0.1 0.0 4/15 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 1 DocID7699 Rev 9 10 100 1000 T4 series Characteristics Figure 7. Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms  Figure 8. Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values) , 760 $ IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25°C] 2.5 7 M LQLWLDO ƒ& 2.0 GOGWOLPLWDWLRQ  $—V , 760 IGT 1.5 IH & IL 1.0  0.5   W S PV Tj(°C) 0.0    Figure 9. Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values) -40 -20 0 20 40 60 80 100 120 140 Figure 10. Relative variation of critical rate of decrease of main current versus junction temperature (dI/dt)c [Tj] / (dI/dt)c [Tj specified] (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c 6 2.4 2.2 5 2.0 1.8 4 1.6 1.4 1.2 3 T435 1.0 0.8 2 T410 0.6 T405 0.4 1 0.2 (dV/dt)c (V/µs) Tj(°C) 0.0 0 0.1 1.0 10.0 100.0 0 25 50 75 100 125 Figure 11. DPAK thermal resistance junction to ambient versus copper surface under tab (printed circuit board FR4, copper thickness: 35 µm) Rth(j-a)(°C/W) 100 90 80 70 60 50 40 30 20 10 S(cm²) 0 0 4 8 12 16 20 24 DocID7699 Rev 9 28 32 36 40 5/15 Package information 2 T4 series Package information  Molding epoxy meets UL94, V0 and is halogen free  Lead-free package  Recommended torque: 0.4 to 0.6 N·m for TO-220AB In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 DPAK package information Figure 12. DPAK package outline $ ( E F / ' ' + $ ( / H E H F $ Note: 6/15 ' 9 / This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID7699 Rev 9 T4 series Package information Table 7. DPAK package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. A 2.18 2.40 0.086 0.0944 A1 0.9 1.10 0.035 0.0433 A2 0.03 0.23 0.0011 0.0090 b 0.64 0.90 0.0251 0.0354 b4 4.95 5.46 0.1948 0.2149 c 0.46 0.61 0.0181 0.0240 c2 0.46 0.60 0.0181 0.0236 D 5.97 6.22 0.2350 0.2448 D1 4.95 E 6.35 E1 4.32 0.1948 6.73 0.2500 0.2649 0.1700 e 2.286 0.09 e1 4.572 0.18 H 9.35 10.40 0.3681 0.4094 L 1.0 1.78 0.039 0.0700 L2 1.27 0.0500 L4 0.6 1.02 0.023 0.0401 V2 -8° +8° -8° +8° 1. Inch dimensions are only for reference Figure 13. Footprint (dimensions in mm)      % 7KHGHYLFHPXVWEHSRVLWLRQHGZLWKLQ DocID7699 Rev 9 $   $ % 7/15 Package information 2.2 T4 series IPAK package information Figure 14. IPAK package outline ( E $ F 9 / ' / $ E H E H Note: 8/15 + / F This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID7699 Rev 9 T4 series Package information Table 8. IPAK package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. A 2.20 2.40 0.0866 0.0945 A1 0.90 1.10 0.0354 0.0433 b 0.64 0.90 0.0252 0.0354 b2 0.95 0.0374 b4 5.20 5.43 0.2047 0.2138 c 0.45 0.60 0.0177 0.0236 c2 0.46 0.60 0.0181 0.0236 D 6 6.20 0.2362 0.2441 E 6.40 6.65 0.2520 0.2618 e e1 2.28 4.40 H 0.0898 4.60 0.1732 16.10 0.1811 0.6339 L 9 9.60 0.3543 0.3780 L1 0.8 1.20 0.0315 0.0472 L2 0.80 V1 10° 1.25 0.0315 0.0492 10° 1. Inch dimensions are only for reference DocID7699 Rev 9 9/15 Package information 2.3 T4 series TO-220AB (insulated and non-insulated) information Figure 15. TO-220AB (insulated and non-insulated) package outline & % ‘, E / ) $ , O F D O D 0 E H 10/15 DocID7699 Rev 9 F T4 series Package information Table 9. TO-220AB (insulated and non-insulated) package mechanical data Dimensions Ref. Min. A Inches(1) Millimeters Typ. 15.20 a1 Max. Min. 15.90 0.5984 3.75 Typ. Max. 0.6259 0.1476 a2 13.00 14.00 0.5118 0.5511 B 10.00 10.40 0.3937 0.4094 b1 0.61 0.88 0.0240 0.0346 b2 1.23 1.32 0.0484 0.0519 C 4.40 4.60 0.1732 0.1811 c1 0.49 0.70 0.0192 0.0275 c2 2.40 2.72 0.0944 0.1070 e 2.40 2.70 0.0944 0.1062 F 6.20 6.60 0.2440 0.2598 ØI 3.73 3.88 0.1468 0.1527 I4 15.80 16.80 0.6220 L 2.65 2.95 0.1043 0.1161 l2 1.14 1.70 0.0448 0.0669 l3 1.14 1.70 0.0448 0.0669 M 16.40 2.60 0.6456 0.6614 0.1023 1. Inch dimensions are only for reference DocID7699 Rev 9 11/15 Ordering information 3 T4 series Ordering information Figure 16. Order information scheme 7%75 7ULDFVHULHV &XUUHQW  $ 6HQVLWLYLW\  P$  P$  P$ 9ROWDJH  9  9  9 3DFNDJH % '3$. + ,3$. 7 72$% 3DFNLQJPRGH %ODQN 7XEH 75 7DSHDQGUHHO Table 10. Product selector Voltage (xxx) Part number Sensitivity 600 V T405-xxxB X T405-xxxB-TR X T405-xxxH X T405-xxxT 700 V Package 5 mA Logic level DPAK X 5 mA Logic level DPAK X 5 mA Logic level IPAK X 5 mA Logic level TO-220AB T410-xxxB X 10 mA Logic level DPAK T410-xxxB-TR X X 10 mA Logic level DPAK T410-xxxH X X 10 mA Logic level IPAK T410-xxxT X X 10 mA Logic level TO-220AB T435-xxxB X 35 mA Snubberless DPAK T435-xxxB-TR X X 35 mA Snubberless DPAK T435-xxxH X X 35 mA Snubberless IPAK T435-xxxT X X 35 mA Snubberless TO-220AB X X X Blank = Unavailable 12/15 Type 800 V DocID7699 Rev 9 T4 series Ordering information Table 11. Ordering information Order code Marking T405-600B T4 0560 T410-600B T4 1060 T435-600B T4 3560 T405-600B-TR T4 0560 T410-600B-TR T4 1060 T435-600B-TR T4 3560 T405-700B-TR T4 0570 T435-700B-TR T4 3570 T405-800B-TR T4 0580 T410-800B-TR T4 1080 T435-800B-TR T4 3580 T405-600H T4 0560 T410-600H T4 1060 T435-600H T4 3560 T405-800H T4 0580 T410-800H T4 1080 T435-800H T4 3580 T405-600T T405-600T T410-600T T410-600T T435-600T T435-600T T410-700T T410-700T T410-800T T410-800T T435-800T T435-800T Package DPAK IPAK Weight Base qty. Delivery mode 75 Tube 2500 Tape and reel 0.3 g 0.4 g 75 Tube TO-220AB DocID7699 Rev 9 2.3 g 50 13/15 Revision history 4 T4 series Revision history Table 12. Document revision history 14/15 Date Revision Changes Jun-2003 2 Last updated. 25-Mar-2005 3 Layout updated, No content change. 25-Jan-2006 4 Markings changed in Table 12. 14-May-2014 5 Updated DPAK and IPAK package information and reformatted to current standard. 11-Feb-2015 6 Updated package silhouettes in cover page. 1-Apr-2016 7 Removed ISOWATT-220AB package information. 05-Oct-2016 8 Updated Table 3 and Table 11. Updated Figure 2 and Figure 4. 14-Nov-2016 9 Updated Table 1. DocID7699 Rev 9 T4 series IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID7699 Rev 9 15/15