T405Q-600B-TR

T405Q-600 4 A sensitiveTriacs Datasheet - production data Description A2 Sensitive Triacs are intended in general purpose applications where high surge current capability is required. These Triacs feature a gate current capability sensitivities of 5 mA or 10 mA depending on the quadrant. G A1 A2 A1 A2 . A1 A2 G G Table 1. Device summary A2 DPAK IPAK Features Symbol Value Unit IT(rms) 4 A VDRM, VRRM 600 V VDSM, VRSM 700 V IGT 5 / 10(1) mA 1. Quadrant I,II,III = 5 mA, quadrant IV = 10 mA.  MCU direct gate drive  4 quadrants Triac  ECOPACK®2 compliant component Applications  Motor control circuits  Small home appliances  Fan speed controller  Pump and valve drive  Mahjong machines  Lighting dimmers February 2016 This is information on a product in full production. DocID10368 Rev 4 1/12 www.st.com Characteristics 1 T405Q-600 Characteristics Table 2. Absolute maximum ratings (Tj = 25 °C unless otherwise stated) Symbol Parameter Value Unit Tc = 110 °C 4 A Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) tp = 20 ms 35 tp = 16.7 ms 38 I²t value for fusing tp = 10 ms 6 A ²s dI/dt Critical rate of rise of on-state current IG = 2 x IGT, tr ≤ 100 ns F = 100 Hz 50 A/µs IGM Peak gate current Tj = 125 °C 4 A Tj = 125 °C 0.5 W - 40 to + 150 - 40 to + 125 °C 700 V On-state rms current (full sine wave) IT(rms) ITSM I²t PG(AV) IPAK, DPAK tp = 20 µs Average gate power dissipation Storage junction temperature range Operating junction temperature range Tstg Tj VDSM, VRSM Non repetitive surge peak off-state voltage tp = 10 ms A Table 3. Electrical characteristics (Tj = 25 °C, unless otherwise stated) Value Symbol Test conditions Quadrant Unit T405Q IGT(1) VD = 12 V, RL = 30 Ω I - II - III IV Max. 5 10 mA VGT VD = 12 V, RL = 30 Ω All Max. 1.3 V VGD VD = VDRM, RL = 3.3 k Ω , Tj = 125 °C All Min. 0.2 V Max. 10 mA I - III - IV Max. 10 II Max. 15 VD = 67% VDRM, gate open Tj = 125 °C Min. 10 V/µs (dV/dt)c = 2 V/µs Tj = 125 °C Min. 1.8 A/ms IH (2) IT = 100 mA IL IG = 1.2 IGT dV/dt (2) (dI/dt)c (2) mA 1. Minimum IGT is guaranteed at 5% of IGT max. 2. For both polarities of A2 referenced to A1 2/12 DocID10368 Rev 4 T405Q-600 Characteristics Table 4. Static characteristics Symbol VTM (1) Test conditions Value Unit ITM = 5 A, tp = 380 µs Tj = 25 °C Max. 1.5 V Vt0 (1) Threshold voltage Tj = 125 °C Max. 0.85 V Rd (1) Dynamic resistance Tj = 125 °C Max. 100 m 5 µA 1 mA Value Unit 3 °C/W DPAK 70 °C/W IPAK 100 °C/W IDRM IRRM Tj = 25 °C VDRM = VRRM Max. Tj = 125 °C 1. For both polarities of A2 referenced to A1 Table 5. Thermal resistance Symbol Rth(j-c) Parameter Junction to case (AC) S(1) Rth(j-a) = 0.5 cm² Junction to ambient 1. S = Copper surface under tab. DocID10368 Rev 4 3/12 12 Characteristics T405Q-600 Figure 1. Maximum power dissipation versus RMS on-state current Figure 2. RMS on-state current versus case temperature P(W) IT(RMS)(A) 5 5.0 α=180° α=180° 4.5 4 4.0 3.5 3 3.0 2.5 2.0 2 1.5 180° α 1 α 1.0 0.5 IT(RMS)(A) 0.0 0.5 1.0 1.5 2.0 TC(°C) 0.0 0 2.5 3.0 3.5 0 4.0 25 Figure 3. Relative variation of thermal impedance versus pulse duration 50 75 100 125 Figure 4. On-state characteristics (maximum values) ITM(A) K=[Zth/Rth] 100 1.E+00 Tj max. Vto = 0.85V Rd = 100 mΩ Zth(j-c) 1.E-01 Tj = Tj max. 10 Zth(j-a) 1.E-02 Tj = 25°C. tp(s) 1.E-03 1.E-03 1.E-02 1.E-01 1.E+00 VTM(V) 1.E+01 1.E+02 1.E+03 Figure 5. Surge peak on-state current versus number of cycles 1 0 2 3 4 5 6 7 8 9 10 Figure 6. Non-repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms ITSM(A) 1000 40 1 IT SM (A ) Tj initial=25°C 35 t=20ms 30 dI/dt limitation: 50A/µs One cycle IT SM 100 25 Non repetitive Tj initial=25°C 20 Repetitive TC=110°C 15 10 10 5 t p(ms) Number of cycles 1 0 1 4/12 10 100 1000 0.01 DocID10368 Rev 4 0.10 1.00 10.00 T405Q-600 Characteristics Figure 7. Relative variation of gate trigger current, holding current and latching current versus junction temperature (typical values) Figure 8. Relative variation of critical rate of decrease of main current versus (dV/dt)c (typical values) (dI/dt)c [(dV/dt)c] / Specified (dI/dt)c IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25°C] 2.0 3.0 1.8 2.5 1.6 1.4 2.0 1.2 IGT 1.0 1.5 0.8 1.0 IH & IL 0.6 0.4 0.5 0.2 Tj(°C) 0.0 (dV/dt)c (V/µs) 0.0 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 0.1 Figure 9. Relative variation of critical rate of decrease of main current versus junction temperature 1.0 10.0 Figure 10. Relative variation of static dV/dt immunity versus junction temperature dV/dt [Tj] / dV/dt [Tj = 125°C] (dI/dt)c [Tj] / (dI/dt)c [Tj specified] 8 8 7 7 6 6 5 5 4 4 3 3 2 2 VD=VR=400V 1 1 Tj(°C) Tj(°C) 0 0 25 50 75 100 125 25 50 75 100 125 Figure 11. DPAK thermal resistance junction to ambient versus copper surface under tab (printed circuit board FR4, copper thickness: 35 µm) Rth(j-a)(°C/W) 100 90 80 70 60 50 40 30 20 10 S(cm²) 0 0 2 4 6 8 10 12 14 DocID10368 Rev 4 16 18 20 5/12 12 Package information 2 T405Q-600 Package information  Epoxy meets UL94, V0  Lead-free package  Recommended torque: 0.4 to 0.6 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 DPAK package information $ Figure 12. DPAK package outline ( E + ' ' / F ( / $ H E F $ / 9 H Note: 6/12 This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID10368 Rev 4 T405Q-600 Package information Table 6. DPAK package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. A 2.18 2.40 0.0858 0.0945 A1 0.90 1.10 0.0354 0.0433 A2 0.03 0.23 0.0012 0.0091 b 0.64 0.90 0.0252 0.0354 b4 4.95 5.46 0.1949 0.2150 c 0.46 0.61 0.0181 0.0240 c2 0.46 0.60 0.0181 0.0236 D 5.97 6.22 0.2350 0.2449 D1 4.95 5.60 0.1949 0.2204 E 6.35 6.73 0.2500 0.2650 E1 4.32 5.50 0.1701 0.2165 e 2.286 0.0900 e1 4.40 4.70 0.1732 0.1850 H 9.35 10.40 0.3681 0.4094 L 1.00 1.78 0.0394 0.0701 L2 1.27 0.0500 L4 0.60 1.02 0.0236 0.0402 V2 -8° 8° -8° 8° 1. Inch dimensions are only for reference Figure 13. Footprint (dimensions in mm, drawing not in scale)      % 7KHGHYLFHPXVWEHSRVLWLRQHGZLWKLQ DocID10368 Rev 4 $   $ % 7/12 12 Package information 2.2 T405Q-600 IPAK package information Figure 14. IPAK package outline ( E $ F 9 / ' / $ E H E H Note: 8/12 + / F This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. DocID10368 Rev 4 T405Q-600 Package information Table 7. IPAK package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. A 2.20 2.40 0.0866 0.0945 A1 0.90 1.10 0.0354 0.0433 b 0.64 0.90 0.0252 0.0354 b2 0.95 0.0374 b4 5.20 5.43 0.2047 0.2138 c 0.45 0.60 0.0177 0.0236 c2 0.46 0.60 0.0181 0.0236 D 6 6.20 0.2362 0.2441 E 6.40 6.65 0.2520 0.2618 e e1 2.28 4.40 H 0.0898 4.60 0.1732 16.10 0.1811 0.6339 L 9 9.60 0.3543 0.3780 L1 0.8 1.20 0.0315 0.0472 L2 0.80 V1 10° 1.25 0.0315 0.0492 10° 1. Inch dimensions are only for reference DocID10368 Rev 4 9/12 12 Ordering information 3 T405Q-600 Ordering information Figure 15. Order information scheme T 4 05 Q - 600 B (-T R) Triac series Current 4 = 4A Sensitivity 05 = 5mA in Quandrant I - II - III; 10mA in Quadrant IV Number of quadrants Q=4 Voltage 600 = 600V Package B= DPAK H= IPAK Packing mode Blank= Tube -TR= Tape and reel Table 8. Product selector Part Number Voltage Sensitivity Type Package T405Q-600B-TR 600 V 5 / 10 mA Sensitive DPAK T405Q-600H 600 V 5 / 10 mA Sensitive IPAK Table 9. Ordering information 10/12 Order code Marking Package Weight Base qty Delivery mode T405Q-600B-TR T405Q 600 DPAK 0.3 g 2500 Tape and reel T405Q-600H T405Q 600 IPAK 0.4 g 75 Tube DocID10368 Rev 4 T405Q-600 4 Revision history Revision history Table 10. Document revision history Date Revision Changes July-2002 1 First issue. 29-May-2014 2 Updated DPAK and IPAK package information and reformatted to current standard. 25-Sep-2015 3 Updated Features in cover page. Updated Table 3 and Section 2: Package information. 11-Feb-2016 4 Updated DPAK package information and reformatted to current standard. Added VDSM parameter. DocID10368 Rev 4 11/12 12 T405Q-600 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved 12/12 DocID10368 Rev 4