T405T-6FP

T405T-6FP 4 A logic level Triac Datasheet - production data Description G Based on ST’s logic level technology providing high commutation performance, this device is suitable for use on AC low current loads. It is recommended for motor driving, electro valves, kitchen appliances, power tools and dishwashers. Available in a fully insulated package, it complies with standard UL1557. Table 1: Device summary A2 A1 Symbol Value Unit IT(RMS) 4 A VDRM/VRRM 600 V IGT 5 mA Tj max. 125 °C TO-220FPAB Features      Three triggering quadrants Triac VDRM / VRRM = 600 V UL certified device rated 2000 VRMS (ref. file E81734) ECOPACK®2 compliant component Halogen-free molding, lead-free plating Package TO-220FPAB Ordering code T405T-6FP Applications    General purpose AC inductive loads Induction motor control circuits Small home appliances Benefits    Low gate consumption Direct drive from microcontroller Direct mounting on heat sink November 2016 DocID029919 Rev 1 This is information on a product in full production. 1/9 www.st.com Characteristics 1 T405T-6FP Characteristics Table 2: Absolute maximum ratings (limiting values) Symbol IT(RMS) Parameter RMS on-state current (full sine wave) Tc = 104 °C Value Unit 4 A Non repetitive surge peak on-state current (full sine cycle) tp = 16.7 ms I2t value for fusing tp = 10 ms Tj initial = 25 °C 5.1 A2s dl/dt Critical rate of rise of onstate current IG = 2 x IGT, tr ≤ 100 ns f = 120 Hz 50 A/µs IGM Peak gate current 4 A tp = 20 µs Tj = 125 °C 1 W ITSM I2 t tp = 20 ms 31 Tj initial = 25 °C 30 A PGM Maximum gate power dissipation Tstg Storage junction temperature range -40 to +150 °C Tj Operating junction temperature range -40 to +125 °C TL Maximum lead temperature for soldering during 10 s 260 °C Vins Insulation RMS voltage (60 seconds) 2000 V Value Unit Table 3: Static electrical characteristics Symbol Test conditions Tj VTM ITM = 5.5 A, tp = 380 µs 25 °C Max. 1.56 V VTO threshold on-state voltage 125 °C Max. 0.9 V RD Dynamic resistance 125 °C Max. 100 mΩ IDRM IRRM 25 °C VD = VDRM, VR = VRRM Max. 5 µA 125 °C Max. 1 mA Value Unit Max. 5 mA Max. 1.3 V Min. 0.2 V Max. 15 Max. 10 Table 4: Dynamic characteristics Symbol IGT Parameter Quadrant VGT VGD VD = 12 V, RL = 30 Ω VD = VDRM, RL = 3.3 kΩ IL IG = 1.2 x IGT IH ITM = 100 mA dV/dt(2) (dl/dt)c(2) 25 °C I - II - III (1)Minimum 2/9 125 °C 25 °C VD = VR = 402 V, gate open (dV/dt)c = 0.1 V/µs Notes: (2)For Tj (1) IGT is guaranteed at 5 % of IGT max. both polarities of A2 referenced to A1 DocID029919 Rev 1 125 °C mA Min. 20 V/µs Min. 1.8 A/ms T405T-6FP Characteristics Table 5: Thermal resistance Symbol Parameter Value Rth(j-c) Max. junction to case thermal resistance (AC) 4.3 Rth(j-a) Typical junction to ambient thermal resistance 60 DocID029919 Rev 1 Unit °C/W 3/9 Characteristics 1.1 T405T-6FP Characteristics (curves) Figure 1: Maximum power dissipation versus onstate RMS current P(W) 5.00 Figure 2: RMS on-state current versus temperature under tab. (full cycle) 5.00 4.00 IT(RMS)(A) 4.00 3.00 3.00 2.00 2.00 1.00 1.00 IT(RMS)(A) 0.00 0.00 TC(°C) 1.00 2.00 3.00 4.00 0.00 0 50 75 100 125 Figure 4: Relative variation of thermal impedance versus pulse duration Figure 3: RMS on-state current versus ambient temperature (free air convection) 2.50 25 IT(RMS)(A) 1.0E+00 K = [Zth/Rth] Zth(j-c) Zth(j-a) 2.00 1.50 1.0E-01 1.00 0.50 t P(s) Ta (°C) 0.00 0 25 50 75 100 125 1.0E-02 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 1.0E+04 Figure 5: On-state characteristics (maximum values) Figure 6: Surge peak on-state current versus number of cycles 40 ITSM(A) t = 20 ms 30 One cycle Non repetitive Tj initial = 25 °C 20 10 Repetitive Tc = 104°C Number of cycles 0 1 4/9 DocID029919 Rev 1 10 100 1000 T405T-6FP Characteristics Figure 7: Non repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms 1.E+04 Figure 8: Relative variation of gate trigger current and gate trigger voltage versus junction temperature (typical values) ITSM(A) Tj initial = 25 °C ITSM 1.E+03 1.E+02 1.E+01 1.E+00 t P(ms) 1.E-01 0.01 0.10 1.00 10.00 Figure 9: Relative variation of holding current and latching current versus junction temperature (typical values) Figure 10: Relative variation of critical rate of decrease of main current (dI/dt)c versus reapplied (dV/dt)c (dI/dt)c [ (dV/dt)c ] / specified (dI/dt)c 1.2 1.0 0.8 0.6 0.4 0.2 (dV/dt)c (V/µs) 0.0 0.1 10.0 100.0 Figure 12: Relative variation of static dV/dt immunity versus junction temperature Figure 11: Relative variation of critical rate of decrease of main current versus junction temperature (typical values) 4 1.0 (dI/dt) C [T j ] / (dI/dt) c [T j = 125 °C] dV/dt [T j ] / dV/dt [T j = 125 °C] 6 VD = VR = 402 V 5 3 4 3 2 2 1 1 Tj (°C) Tj (°C) 0 0 25 25 50 75 100 50 75 100 125 125 DocID029919 Rev 1 5/9 Package information 2 T405T-6FP Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.     2.1 ECOPACK®2 compliant Lead-free package leads finishing Molding compound resin is halogen-free and meets UL94 level V0 Recommended torque (for through-hole package): 0.4 to 0.6 N·m TO-220FPAB package information Figure 13: TO-220FPAB package outline 6/9 DocID029919 Rev 1 Package information T405T-6FP Table 6: TO-220FPAB package mechanical data Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.1739 0.1818 B 2.5 2.7 0.0988 0.1067 D 2.50 2.75 0.0988 0.1087 E 0.45 0.70 0.0178 0.0277 F 0.75 1.0 0.0296 0.0395 F1 1.15 1.70 0.0455 0.0672 F2 1.15 1.70 0.0455 0.0672 G 4.95 5.20 0.1957 0.2055 G1 2.40 2.70 0.0949 0.1067 H 10.00 10.40 0.3953 0.4111 L2 16.00 typ. 0.6324 typ. L3 28.60 30.60 1.1304 1.2095 L4 9.80 10.6 0.3874 0.4190 L5 2.90 3.60 0.1146 0.1423 L6 15.90 16.40 0.6285 0.6482 L7 9.00 9.30 0.3557 0.3676 Dia 3.0 3.20 0.1186 0.1265 DocID029919 Rev 1 7/9 Ordering information 3 T405T-6FP Ordering information Figure 14: Ordering information scheme T 4 05 T - 6 FP Series Triac RMS current 4 = 4A Gate triggering current 05 = 5 mA Maximum junction temperature 125 °C Voltage 6 = 600 V Package FP= TO-220FPAB Table 7: Ordering information 4 Order code Marking Package Weight Base qty. Delivery mode T405T-6FP T405T-6FP TO-220FPAB 2.0 g 50 Tube Revision history Table 8: Document revision history 8/9 Date Revision 04-Nov-2016 1 Changes Inital release. DocID029919 Rev 1 T405T-6FP IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID029919 Rev 1 9/9