T435T-600FP

T435T-600FP 4 A Snubberless™ Triac Datasheet - production data Description A2 Available in through-hole package, the Triac T435T-600FP is suitable for general purpose AC switching. Specially designed for power tool applications, it can also be used to drive loads like motor speed controller, and kitchen equipment such as electro valves, light dimmers and similar. G A1 TO-220FPAB G A2 A1 Features • High static and dynamic commutation • Package is RoHS (2002/95/EC) compliant • IGT = 35 mA • ECOPACK®2 compliant component • Provides UL certified insulation rate at 2.0 kV rms TM: Snubberless is a trademark of STMicroelectronics July 2014 This is information on a product in full production. DocID17632 Rev 3 1/9 www.st.com Characteristics 1 T435T-600FP Characteristics Table 1. Absolute maximum ratings (limiting values) Symbol IT(RMS) ITSM I ²t dI/dt Parameter On-state rms current (full sine wave) PG(AV) Tstg Tj Unit Tc = 105 °C 4 A Non repetitive surge peak on-state current (full cycle sine wave, TJ initial = 25 °C) F = 60 Hz t = 16.7 ms 32 F = 50 Hz t = 20 ms 30 I²t Value for fusing tp = 10 ms Critical rate of rise of on-state current IG = 2 x IGT, tr ≤ 100 ns F = 120 Hz Tj = 125 °C tp = 10 ms Tj = 25 °C tp = 20 µs Tj = 125 °C 4 A Tj = 125 °C 1 W -40 to +150 -40 to +125 °C VDSM/VRSM Non repetitive surge peak off-state voltage IGM Value Peak gate current A Average gate power dissipation Storage junction temperature range Operating junction temperature range 6 A ²s 50 A/µs VDRM/VRRM V + 100 Table 2. Electrical characteristics, Snubberless (3 quadrants) (Tj = 25 °C, unless otherwise specified) Symbol Test conditions Value Unit IGT(1) VD = 12 V RL = 30 Ω I - II - III MAX 35 mA VGT VD = 12 V RL = 30 Ω I - II - III MAX 1.3 V VGD VD = VDRM RL = 3.3 kΩ I - II - III MIN 0.2 V IH (2) IT = 100 mA MAX 35 mA I - III MAX 50 IL IG = 1.2 x IGT II MAX 80 VD = 67% VDRM, gate open, Tj = 125 °C MIN 750 V/µs Without snubber, Tj = 125 °C MIN 5.3 A/ms 2.0 kV dV/dt (2) (dI/dt)c (2) Vins mA Insulation rms voltage, 1 minute 1. Minimum IGT is guaranteed at 5% of IGT max. 2. For both polarities of A2 pin referenced to A1 pin 2/9 Quadrant DocID17632 Rev 3 T435T-600FP Characteristics Table 3. Static electrical characteristics Symbol Test conditions Value Unit VTM(1) ITM = 5.7 A, tp = 380 µs Tj = 25 °C MAX 1.6 V VTO(1) Threshold voltage Tj = 125 °C MAX 0.9 V Dynamic resistance Tj = 125 °C MAX 100 mΩ 5 µA 1 mA Value Unit RD (1) IDRM IRRM Tj = 25 °C VDRM = VRRM MAX Tj = 125 °C 1. For both polarities of A2 pin referenced to A1 pin Table 4. Thermal resistances Symbol Parameter Rth(j-c) Junction to case (ac) 4.3 Rth(j-a) Junction to ambient 60 °C/W Figure 1. Maximum power dissipation versus rms on-state current (full cycle) 5 Figure 2. On-state current (rms) versus case temperature (full cycle) P(W) 5.0 IT(RMS)(A) α=180° 4.5 4 4.0 3.5 3 3.0 2.5 2 2.0 1.5 1 1.0 180° TC(°C) 0.5 IT(RMS)(A) 0.0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Figure 3. On-state current (rms) versus ambient temperature (free air convection) IT(RMS) (A) 0 50 75 100 125 Figure 4. Relative variation of thermal impedance versus pulse duration 1.0E+00 2.5 25 K=[Zth/Rth] α=180° Zth(j-c) 2.0 Zth(j-a) 1.5 1.0E-01 1.0 0.5 Tamb(°C) tP(s) 0.0 0 25 50 75 100 125 1.0E-02 1.0E-03 DocID17632 Rev 3 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 3/9 9 Characteristics T435T-600FP Figure 5. Relative variation of gate trigger current, and gate trigger voltage versus junction temperature Figure 6. Relative variation of holding current and latching current versus junction temperature IH, IL [T j] / IH, IL [T j=25 °C] IGT, VGT[T j] / IGT, VGT[T j=25 °C] 3.0 3.0 typical values typical values IGT Q3 2.5 2.5 2.0 2.0 IGT Q1-Q2 1.5 1.5 1.0 1.0 VGT Q1-Q2-Q3 0.5 0.5 Tj(°C) T j(°C) 0.0 0.0 -40 -30 -20 -10 0 Figure 7. Surge peak on-state current versus number of cycles 35 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 ITSM (A) 10 20 30 40 50 60 70 80 90 100 110 120 130 Figure 8. Non-repetitive surge peak on-state current for a sinusoidal 1000 ITSM(A), I²t (A²s) Tj initial=25 °C dI/dt limitation: 50 A/µs 30 t=20ms 25 One cycle Non repetitive Tj initial=25 °C ITSM 100 20 2 pulse tp < 10 ms, and corresponding value of I t 15 Repetitive TC=105 °C 10 10 I²t 5 tP(ms) Number of cycles 0 1 1 10 100 1000 Figure 9. On-state characteristics (maximum values) 100 0.01 0.10 1.00 10.00 Figure 10. Relative variation of critical rate of decrease of main current (dI/dt)c versus junction temperature ITM(A) 8 (dI/dt)c [T j] / (dI/dt)c [T j=125 °C] 7 Tj=25 °C 6 Tj=125 °C 5 4 10 3 2 Tj max : Vto = 0.9 V Rd = 100 mΩ VTM(V) 1 1 0 4/9 1 2 3 4 5 6 T j(°C) 0 7 25 DocID17632 Rev 3 50 75 100 125 T435T-600FP Characteristics Figure 11. Relative variation of critical rate of decrease of main current (dI/dt)c versus reapplied (dV/dt)c 2.0 (dI/dt)c [ (dV/dt) c ] / Specified (dI/dt) c Figure 12. Relative variation of static dV/dt immunity versus junction temperature 8 dV/dt [T j] / dV/dt [T j=125 °C] typical values VD=VR=400 V 1.8 7 1.6 6 1.4 5 1.2 1.0 4 0.8 3 0.6 2 0.4 0.2 1 (dV/dt)c(V/µs) T j(°C) 0 0.0 0.1 1.0 10.0 100.0 25 DocID17632 Rev 3 50 75 100 125 5/9 9 Package information 2 T435T-600FP Package information • Epoxy meets UL94, V0 • Lead-free packages In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Figure 13. TO-220FPAB dimension definitions A B H Dia L6 L2 L7 L3 L5 F1 L4 F2 F G1 G 6/9 D DocID17632 Rev 3 E T435T-600FP Package information Table 5. TO-220FPAB dimension values Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A 4.4 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.70 0.045 0.067 F2 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 L2 16 Typ. 0.63 Typ. L3 28.6 30.6 1.126 1.205 L4 9.8 10.6 0.386 0.417 L5 2.9 3.6 0.114 0.142 L6 15.9 16.4 0.626 0.646 L7 9.00 9.30 0.354 0.366 Dia. 3.00 3.20 0.118 0.126 DocID17632 Rev 3 7/9 9 Ordering information 3 T435T-600FP Ordering information Figure 14. Ordering information scheme T 4 35 T - 600 FP Triac series Current 4=4A Sensitivity 35 = 35 mA Specific application Voltage 600 = 600 V Package FP = Fullpack Table 6. Ordering information 4 Order code Marking Package Weight Base qty Packing mode T435T-600FP T435T-600 TO-220FPAB 2.0 g 50 Tube Revision history Table 7. Document revision history 8/9 Date Revision Changes 09-Nov-2007 1 Initial release. 14-Jun-2010 2 Updated ECOPACK statement. 28-Jul-2014 3 Updated Features, Table 2 and Figure 14 and reformatted to current standard. DocID17632 Rev 3 T435T-600FP IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2014 STMicroelectronics – All rights reserved DocID17632 Rev 3 9/9 9