TDA7569BLV
4 x 50 W power amplifier with full I2C diagnostics,
high efficiency and low voltage operation
Datasheet - production data
Very robust against misconnections
Improved SVR suppression during battery
transients
'!0'03
'!0'03
Flexiwatt27 (Horiz.)
Flexiwatt27 (SMD)
Capable to operate down to 6 V (e.g. “Startstop”)
Description
The TDA7569BLV is the most advanced BCD
technology quad bridge car radio amplifier of his
family, including a wide range of innovative
features.
'!0'03
'!0'03
Flexiwatt27 (Vert.)
PowerSO36
Features
The TDA7569BLV is equipped with the most
complete diagnostics array that communicates
the status of each speaker through the I2C bus.
Multipower BCD technology
MOSFET output power stage
DMOS power output
Class SB high efficiency
High output power capability 4x28 W/4 Ω @
14.4 V, 1 kHz, 10% THD, 4 x 45 W max power
Max power 4 x 72 W / 2
Full I2C bus driving:
– Standby
– Independent front/rear soft play/mute
– Selectable gain 26 dB /16 dB (for low noise
line output function)
– High efficiency enable/disable
– I2C bus digital diagnostics (including DC
bus AC load detection)
The dissipated output power under average
listening condition is significantly reduced when
compared to the conventional class AB solutions,
thanks to the patented solution. Moreover it has
been designed to be very robust against several
kinds of misconnections.
It is moreover compliant to the most recent OEM
specifications for low voltage operation (so called
'start-stop' battery profile during engine stop and
re-start), helping car manufacturers to reduce the
overall emissions and thus contributing to
environment protection.
Figure 1. Device summary
Order code
Package
Packing
Full fault protection
TDA7569BLVSM
Tube
DC offset detection
TDA7569BLVSMTR
Flexiwatt27
(SMD)
Four independent short circuit protection
Clipping detector pin with selectable threshold
(2 %/10 %)
Standby/mute pin
Linear thermal shutdown with multiple thermal
warning
Tape and reel
TDA7569BLV
Flexiwatt27
(vertical)
Tube
TDA7569BLVH
Flexiwatt27
(horizontal)
Tube
TDA7569BLVPD
TDA7569BLVPDTR
PowerSO36
Tube
Tape and reel
ESD protection
September 2014
This is information on a product in full production.
DocID023498 Rev 9
1/41
www.st.com
Contents
TDA7569BLV
Contents
1
Block diagram and application circuits . . . . . . . . . . . . . . . . . . . . . . . . . 6
2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4
5
3.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4
Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Diagnostics functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.1
Turn-on diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.2
Permanent diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.3
Output DC offset detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.4
AC diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Multiple faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.1
6
Thermal protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
6.1
7
8
9
2/41
Faults availability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Fast muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Battery transitions management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.1
Low voltage operation (“start stop”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7.2
Advanced battery management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Application suggestion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.1
Inputs impedance matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8.2
High efficiency introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
I2C bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9.1
I2C programming/reading sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9.2
Address selection and I2C disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
DocID023498 Rev 9
TDA7569BLV
9.3
Contents
I2C bus interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9.3.1
Data validity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
9.3.2
Start and stop conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
9.3.3
Byte format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
9.3.4
Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10
Software specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
11
Examples of bytes sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
12
Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
13
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DocID023498 Rev 9
3/41
3
List of tables
TDA7569BLV
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
4/41
Pin list description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Double fault table for turn-on diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
IB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
IB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
DB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
DB2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DB3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DB4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Document revision history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DocID023498 Rev 9
TDA7569BLV
List of figures
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
Figure 43.
Figure 44.
Figure 45.
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Application circuit (TDA7569BLVPD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin connection diagram of the Flexiwatt27 (top of view). . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin connection diagram of the PowerSO36 slug up (top of view). . . . . . . . . . . . . . . . . . . . . 8
Quiescent current vs. supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Output power vs. supply voltage (4 Ω) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Distortion vs. output power (4 Ω, STD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Distortion vs. output power (4 Ω, HI-EFF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Distortion vs. output power (2 Ω, STD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Distortion vs. output power (2 Ω, HI-EFF). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Distortion vs. frequency (2 Ω) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Distortion vs. output power Vs = 6 V (4 Ω, STD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Distortion vs. frequency (4 Ω) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Crosstalk vs. frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Supply voltage rejection vs. frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power dissipation vs. average output power (audio program simulation, 2 Ω). . . . . . . . . . 15
Power dissipation vs. average output power (audio program simulation, 4 Ω). . . . . . . . . . 16
Total power dissipation and efficiency vs. output power (4 Ω, HI-EFF, Sine). . . . . . . . . . . 16
Total power dissipation and efficiency vs. output power (4 Ω, STD, Sine) . . . . . . . . . . . . . 16
ITU R-ARM frequency response, weighting filter for transient pop. . . . . . . . . . . . . . . . . . . 16
Turn-on diagnostic: working principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SVR and output behavior (Case 1: without turn-on diagnostic) . . . . . . . . . . . . . . . . . . . . . 17
SVR and output pin behavior (Case 2: with turn-on diagnostic) . . . . . . . . . . . . . . . . . . . . . 18
Short circuit detection thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Load detection thresholds - high gain setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Load detection threshold - low gain setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Restart timing without diagnostic enable (permanent) - Each 1 mS time,
a sampling of the fault is done . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Restart timing with diagnostic enable (permanent). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Current detection high: load impedance |Z| vs. output peak voltage . . . . . . . . . . . . . . . . . 21
Current detection low: load impedance |Z| vs. output peak voltage . . . . . . . . . . . . . . . . . . 21
Thermal foldback diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Worst case battery cranking curve sample 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Worst case battery cranking curve sample 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Upwards fast battery transitions diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Inputs impedance matching circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
High efficiency - basic structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Data validity on the I2C bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Timing diagram on the I2C bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Acknowledge on the I2C bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Flexiwatt27 (horizontal) mechanical data and package dimensions. . . . . . . . . . . . . . . . . . 36
Flexiwatt27 (vertical) mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . . 37
Flexiwatt27 (SMD) mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . . . 38
PowerSO36 (slug up) mechanical data and package dimensions . . . . . . . . . . . . . . . . . . . 39
DocID023498 Rev 9
5/41
5
Block diagram and application circuits
1
TDA7569BLV
Block diagram and application circuits
Figure 2. Block diagram
#,+
$!4!
6##
6##
34
"9-54%
4HERMAL
0ROTECTION
$UMP
)#"53
-UTE -UTE
).
2EFERENCE
#$?/54
#LIP
$ETECTOR
&
/54
D"
/54
3HORT#IRCUIT
0ROTECTION
$IAGNOSTIC
).
2
/54
D"
).
/54
3HORT#IRCUIT
0ROTECTION
$IAGNOSTIC
&
/54
D"
).
3HORT#IRCUIT
0ROTECTION
$IAGNOSTIC
2
/54
/54
D"
3HORT#IRCUIT
0ROTECTION
$IAGNOSTIC
!#?'.$
362
/54
!$SEL
3'.$
4! "
!$3%,
)#$)3
07 ?'.$
'!0'03
Figure 3. Application circuit
6S
#
&
#
&
6CC
666CC
K7
34
"9
6CC
/54
$!4!
#,+
)#"53
/54
).
).
).
).
).
).
#&
#&
#&
4$!",6
4$!",634$!",6(
/54
#&
/54
3'.$
!#'.$
#
&
!$3%,)#$)3
362
4!"
2K7
#
&
6
#$
2EFERTOCHAPTERFORCONNECTIONSUGGESTIONS
&ISTHEMINIMUMRECOMMENDEDVALUE
6/41
DocID023498 Rev 9
'!0'03
TDA7569BLV
Block diagram and application circuits
Figure 4. Application circuit (TDA7569BLVPD)
6S
#
#
&
&
6CC 6CC 6CC
666CC
6 6 6CC
K7 34
"9
6CC
/54
$!4!
#,+
)#"53
/54
).
).
#&
#&
#
&
7'$%/93'
/54
).
).
).
#&
#&
/54
3'.$
!#'.$
#
&
!$3%,)#$)3
362
4!"
2K7
#
&
6
#$
2EFERTOCHAPTERFORCONNECTIONSUGGESTIONS
&ISTHEMINIMUMRECOMMENDEDVALUE&SUGGESTEDASWELL
DocID023498 Rev 9
'!0'03
7/41
40
Pin description
2
TDA7569BLV
Pin description
For channel name reference: CH1 = LF, CH2 = LR, CH3 = RF and CH4 = RR.
Figure 5. Pin connection diagram of the Flexiwatt27 (top of view)
!$3%,)#$)3
!$3%,)#$)3
$!4!
$!4!
07'.$
07'.$
/54
/54
#+
#+
/54
/54
6##
6##
/54
/54
07'.$
07'.$
/54
/54
!#'.$
!#'.$
).
).
).
).
3'.$
3?'.$
).
).
).
).
362
362
/54
/54
07'.$
/54
/54
6##
6##
/54
/54
#$
/54
#$
/54
/54
/54
07'.$
07'.$
34"9
34"9
4!"
4!"
&LEXIWATTVERTICAL
'!0'03
07'.$
&LEXIWATTHORIZONTAL3-$
'!0'03
Figure 6. Pin connection diagram of the PowerSO36 slug up (top of view)
/54
4!"
6##
/54
07'.$
#+
/54
07'.$
!#'.$
.#
).
6##
).
$!4!
3'.$
/54
.#
!$3%,
).
/54
.#
34"9
).
6##
362
07'.$
.#
.#
/54
.#
07'.$
#$
6##
/54
/54
.#
'!0'03
8/41
DocID023498 Rev 9
TDA7569BLV
Pin description
Table 1. Pin list description
Pin #
Pin #
(PowerSo36) (Flexiwatt27)
Pin name
Function
1
1
TAB
-
2
22
OUT4+
3
23
CK
4
25
PWGND4
5
-
NC
6
-
VCC4
Supply voltage pin4
7
26
DATA
I2C bus data pin/gain selector
8
24
OUT4-
Channel 4, - output
9
27
ADSEL
Address selector pin/ I2C bus disable (legacy select)
10
4
OUT2-
Channel 2, - output
11
2
STBY
Standby pin
12
21
VCC2
Supply voltage pin2
13
3
PWGND2
14
-
NC
Not connected
15
-
NC
Not connected
16
5
CD
Clip detector output pin
17
6
OUT2+
18
-
NC
19
8
OUT1-
Channel 1, - output
20
7
VCC1
Supply voltage pin1
21
9
PWGND1
22
10
OUT1+
23
-
NC
24
11
SVR
SVR pin
25
12
IN1
Input pin, channel 1
26
-
NC
Not connected
27
13
IN2
Input pin, channel 2
28
-
NC
Not connected
29
14
SGND
30
15
IN4
Input pin, channel 4
31
16
IN3
Input pin, channel 3
32
17
AC GND
33
18
OUT3+
34
19
PWGND3
35
-
VCC3
Supply voltage pin3
36
20
OUT3-
Channel 3, - output
Channel 4, + output
I2C bus clock/HE selector
Channel 4 output power ground
Not connected
Channel 2 output power ground
Channel 2, + output
Not connected
Channel 1 output power ground
Channel 1, + output
Not connected
Signal ground pin
AC ground
Channel 3, + output
Channel 3 output power ground
DocID023498 Rev 9
9/41
40
Electrical specifications
TDA7569BLV
3
Electrical specifications
3.1
Absolute maximum ratings
Table 2. Absolute maximum ratings
Symbol
Parameter
Value
Unit
Vop
Operating supply voltage(1)
18
V
VS
DC supply voltage
28
V
Peak supply voltage (for tmax = 50 ms)
50
V
-0.3 to 0.3
V
-0.3 to 6
V
Vpeak
GNDmax
VCK, VDATA
Ground pins voltage
CK and DATA pin voltage
Vcd
Clip detector voltage
-0.3 to Vop
V
Vstby
STBY pin voltage
-0.3 to Vop
V
IO
Ptot
Tstg, Tj
Tamb
Output peak current (not repetitive tmax = 100ms)
8
Output peak current (repetitive f > 10 kHz)
6
Power dissipation Tcase = 70°C (2)
85
W
-55 to 150
°C
-40 to 105
°C
Storage and junction temperature
(3)
Operative temperature range
A
1. For RL = 2 Ω the output current limit is reached for VOP > 16 V; at this supply level internal protections
might be triggered.
2. This is maximum theoretical value; for power dissipation in real application conditions, please refer to
curves reported in Section 3.4: Electrical characteristics curves.
3. A suitable dissipation system should be used to keep Tj inside the specified limits.
3.2
Thermal data
Table 3. Thermal data
Symbol
Rth j-case
3.3
Parameter
Thermal resistance junction-to-case
PowerSO Flexiwatt
Max.
1
1
Unit
°C/W
Electrical characteristics
Refer to the test circuit, VS = 14.4 V; RL = 4 Ω; f = 1 kHz; GV = 26 dB; Tamb = 25 °C; unless
otherwise specified.
Tested at Tamb = 25 °C and Thot = 105 °C; functionality guaranteed for Tj = -40 °C to 150 °C.
Table 4. Electrical characteristics
Symbol
Parameter
Test condition
Min.
Typ.
Max.
RL = 4 ohm
6
-
18
RL = 2 ohm
6
-
16 (1)
Unit
General characteristics
VS
10/41
Supply voltage range
DocID023498 Rev 9
V
TDA7569BLV
Electrical specifications
Table 4. Electrical characteristics (continued)
Symbol
Id
RIN
VAM
Parameter
Test condition
Min.
Typ.
Max.
Unit
Total quiescent drain current
-
-
165
250
mA
Input impedance
-
45
60
70
kΩ
IB1(D7) = 1;
Signal attenuation -6 dB
7
-
8
IB1(D7) = 0 (default);(2)
Signal attenuation -6 dB
5
-
5.8
Min. supply mute threshold
V
VOS
Offset voltage
Mute & play
-80
-
80
Vdth
Dump threshold
-
18.5
19.5
20.5
V
ISB
Standby current
Vstandby = 0
-
1
5
μA
SVR
Supply voltage rejection
f = 100 Hz to 10 kHz; Vr = 1 Vpk;
Rg = 600 Ω
60
70
-
dB
TON
Turn on timing (Mute play
transition)
D2/D1 (IB1) 0 to 1
-
25
50
ms
TOFF
Turn off timing (Play mute
transition)
D2/D1 (IB1) 1 to 0
-
25
50
ms
THWARN1
Average junction temperature for
DB1 (D7) = 1
TH warning 1
-
160
-
THWARN2
Average junction temperature for
DB4 (D7) = 1
TH warning 2
-
145
-
THWARN3
Average junction temperature for
DB4 (D6) = 1
TH warning 3
-
125
-
mV
°C
Audio performances
Max. power(3) Vs = 14.4 V, RL = 4 Ω
PO
THD
Output power
Total harmonic distortion
-
45
-
W
THD = 10 %, RL = 4 Ω
THD = 1 %, RL = 4 Ω
25
20
28
22
-
W
W
RL = 2 Ω; THD 10 %
RL = 2 Ω; THD 1 %
RL = 2 Ω; Max. power(3) Vs = 14.4 V
40
32
60
50
40
75
-
W
W
W
Max power@ Vs = 6 V, RL = 4 Ω
-
6
-
W
PO = 1 W to 10 W; STD mode
HE MODE; PO = 1.5 W
HE MODE; PO = 8 W
-
0.015
0.05
0.1
0.1
0.1
0.5
%
%
%
PO = 1-10 W, f = 10 kHz;
STD mode
-
0.15
0.5
%
GV = 16 dB; STD mode
VO = 0.1 to 5 VRMS
-
0.02
0.05
%
CT
Cross talk
f = 1 kHz to 10 kHz, Rg = 600 Ω
50
65
-
dB
GV1
Voltage gain 1
-
25
26
27
dB
Voltage gain match 1
-
-1
-
1
dB
GV1
Voltage gain 2
-
15
16
17
dB
GV2
GV2
Voltage gain match 2
-
-1
-
1
dB
EIN1
Output noise voltage 1
Rg = 600 Ω 20 Hz to 22 kHz
-
45
60
μV
Output noise voltage 2
Rg = 600 Ω; GV = 16d B
20 Hz to 22 kHz
-
20
30
μV
EIN2
DocID023498 Rev 9
11/41
40
Electrical specifications
TDA7569BLV
Table 4. Electrical characteristics (continued)
Symbol
BW
CMRR
ΔVOITU
Parameter
Test condition
Min.
Typ.
Max.
Unit
100
-
-
kHz
-
70
-
dB
Standby to Mute and
Mute to Standby transition
Tamb = 25 °C,
ITU-R 2K, Csvr = 10 μF
Vs = 14.4 V
-7.5
-
+7.5
mV
Mute to Play transition
Tamb = 25 °C,
ITU-R 2K, Vs = 14.4 V (4)
-7.5
-
+7.5
mV
Play to Mute transition
Tamb = 25 °C,
ITU-R 2K, Vs = 14.4 V (5)
-7.5
-
+7.5
mV
Power bandwidth
-
Input CMRR
Vcm = 1 Vpk-pk, Rg = 0 Ω
ITU Pop filter output voltage
Clip detector
CDLK
Clip det. high leakage current
CD off / VCD = 6 V
-
0
5
μA
CDSAT
Clip det sat. voltage
CD on; ICD = 1 mA
-
-
300
mV
CDTHD
Clip det THD level
D0 (IB1) = 1
5
10
15
%
D0 (IB1) = 0
1
2
3
%
Control pin characteristics
VSBY
Standby/mute pin for standby
-
0
-
1.2
V
VMU
Standby/mute pin for mute
-
2.9
-
3.5
V
VOP
Standby/mute pin for operating
-
4.5
-
18
V
-
1
5
μA
Vst-by/mute = 4.5 V
IMU
Standby/mute pin current
-
0
5
μA
ASB
Standby attenuation
-
90
110
-
dB
AM
Mute attenuation
-
80
100
-
dB
-
-
1.2
V
Vs -1.2
-
-
V
1.8
-
Vs -1.8
V
Vst-by/mute < 1.2 V
Turn on diagnostics 1 (Power amplifier mode)
Pgnd
Short to GND det. (below this
limit, the Output is considered in
short circuit to GND)
Pvs
Short to Vs det. (above this limit,
the output is considered in short
circuit to Vs)
Pnop
Normal operation thresholds.
(Within these limits, the output is
considered without faults).
Power amplifier in standby
Power amplifier in standby
Lsc
Shorted load det.
-
-
0.5
Ω
Lop
Open load det.
85
-
-
Ω
Lnop
Normal load det.
1.5
-
45
Ω
-
-
1.2
V
Turn on diagnostics 2 (Line driver mode)
Pgnd
12/41
Short to GND det. (below this
limit, the output is considered in
short circuit to GND)
Power amplifier in standby
DocID023498 Rev 9
TDA7569BLV
Electrical specifications
Table 4. Electrical characteristics (continued)
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
Pvs
Short to Vs det. (above this limit,
the output is considered in short circuit to Vs)
Vs -1.2
-
-
V
Pnop
Normal operation thresholds.
(Within these limits, the output is considered without faults).
1.8
-
Vs -1.8
V
Lsc
Shorted load det.
-
-
-
1.5
Ω
Lop
Open load det.
-
330
-
-
Ω
Lnop
Normal load det.
-
7
-
180
Ω
-
-
1.2
V
Vs -1.2
-
-
V
1.8
-
Vs -1.8
V
Power amplifier mode
-
-
0.5
Ω
Line driver mode
-
-
1.5
Ω
±1.5
±2
±2.5
V
500
-
-
mA
-
-
250
mA
Permanent diagnostics 2 (Power amplifier mode or line driver mode)
Pgnd
Pvs
Pnop
LSC
Short to GND det. (below this
limit, the Output is considered in
short circuit to GND)
Short to Vs det. (above this limit, Power amplifier in mute or play,
the output is considered in short one or more short circuits
circuit to Vs)
protection activated
Normal operation thresholds.
(Within these limits, the output is
considered without faults).
Shorted load det.
VO
Offset detection
INLH
Normal load current detection
IOLH
Open load current detection
INLL
Normal load current detection
IOLL
Open load current detection
Power amplifier in play,
AC input signals = 0
VO < (VS-5)pk, IB2 (D7) = 0
VO < (VS-5)pk, IB2 (D7) = 1
250
-
-
mA
-
-
125
mA
I2C bus interface
SCL
Clock frequency
-
-
-
400
kHz
VIL
Input low voltage
-
-
-
1.5
V
VIH
Input high voltage
-
2.3
-
-
V
1. When VS > 16 V the output current limit is reached (triggering embedded internal protections).
2. In legacy mode only low threshold option is available.
3. Saturated square wave output.
4. Voltage ramp on STBY pin:
from 3.3 V to 4.2 V in t ≥ 40 ms.
In case of I2C mode command IB1(D1) = 1 (Mute → Unmute rear channels) and/or IB1(D2) = 1 (Mute → Unmute front
channels) must be transmitted before to start the voltage ramp on STBY pin.
5. Voltage ramp on STBY pin:
from 4.05 V to 3.55 V in t ≥ 40 ms.
In case of I2C mode command IB1(D1) = 0 Unmute → Mute rear channels) and/or IB1(D2) = 0 (Unmute → Mute front
channels) must be NOT transmitted before to start the voltage ramp on STBY pin.
DocID023498 Rev 9
13/41
40
Electrical specifications
3.4
TDA7569BLV
Electrical characteristics curves
Figure 7. Quiescent current vs. supply voltage Figure 8. Output power vs. supply voltage (4 Ω)
0O 7
)QM!
6IN
./,/!$3
2,7
FK(Z
0O
MAX
4($
4($
6S6
!'V
Figure 9. Distortion vs. output power (4 Ω, STD)
4($
'!0'03
Figure 10. Distortion vs. output power
(4 Ω, HI-EFF)
34!.$!2$-/$%
6S6
2,7
6S6
'!0'03
4($
()
%&&-/$%
6S6
2,
FK(Z
FK(Z
FK(Z
FK(Z
0O 7
0O 7
Figure 11. Distortion vs. output power
(2 Ω, STD)
Figure 12. Distortion vs. output power
(2 Ω, HI-EFF)
4($
4($
34!.$!2$-/$%
6S6
2,7
()
%&&-/$%
6S6
2,7
FK(Z
FK(Z
FK(Z
FK(Z
14/41
'!0'03
'!0'03
0O 7
'!0'03
DocID023498 Rev 9
0O 7
'!0'03
TDA7569BLV
Electrical specifications
Figure 13. Distortion vs. frequency (2 Ω)
Figure 14. Distortion vs. output power Vs = 6 V
(4 Ω, STD)
4($
4($
34!.$!2$-/$%
6S6
2,7
0O7
34!.$!2$-/$%
6S6
2,7
FK(Z
FK(Z
F(Z
Figure 15. Distortion vs. frequency (4 Ω)
4($
'!0'03
Figure 16. Crosstalk vs. frequency
#2/334! ,+D"
34!.$!2$-/$%
6S6
2,7
0O 7
0O 7
'!0'03
34! .$!2$-/$%
2,7
0O 7
2G7
F(Z
Figure 17. Supply voltage rejection vs.
frequency
F(Z
'!0'03
Figure 18. Power dissipation vs. average output
power (audio program simulation, 2 Ω)
362D"
'!0'03
0TOT7
34$(%-/$%
2G7
6RIPPLE6RMS
6S6
2,X/HM
'!533)!../)3%
34$-/$%
#,)0
34!24
()
%&&-/$%
F(Z
'!0'03
DocID023498 Rev 9
0O7
'!0'03
15/41
40
Electrical specifications
TDA7569BLV
Figure 19. Power dissipation vs. average output
power (audio program simulation, 4 Ω)
Figure 20. Total power dissipation and
efficiency vs. output power (4 Ω, HI-EFF, Sine)
0TOT7
0TOT7
H
34$-/$%
6S6
2,X/HM
'!533)!../)3%
6S
2,7
F+(Z
()%&&
MODE
#,)0
34! 24
H
()
%&&-/$%
0TOT
0TOT7
0TOT
0O7
16/41
0O7
'!0'03
H
6S6
2,7
FK(Z
/UTPUTATTENUATIOND"
Figure 22. ITU R-ARM frequency response,
weighting filter for transient pop
H
'!0'03
Figure 21. Total power dissipation and
efficiency vs. output power (4 Ω, STD, Sine)
0O7
'!0'03
DocID023498 Rev 9
(Z
'!0'03
TDA7569BLV
Diagnostics functional description
4
Diagnostics functional description
4.1
Turn-on diagnostic
It is strongly recommended to activate this function at turn on (standby out) through I2C bus
request. Detectable output faults are:
SHORT TO GND
SHORT TO Vs
SHORT ACROSS THE SPEAKER
OPEN SPEAKER
To verify if any of the above misconnections are in place, a subsonic (inaudible) current
pulse (Figure 23) is internally generated, sent through the speaker(s) and sunk back.The
Turn On diagnostic status is internally stored until a successive diagnostic pulse is
requested (after a I2C reading).
If the "standby out" and "diag. enable" commands are both given through a single
programming step, the pulse takes place first (during the pulse the power stage stays 'off',
showing high impedance at the outputs).
Afterwards, when the Amplifier is biased, the PERMANENT diagnostic takes place. The
previous Turn On state is kept until a short appears at the outputs.
Figure 23. Turn-on diagnostic: working principle
9Va9
,VRXUFH
,P$
,VRXUFH
,VLQN
,VLQN
aPV
WPV
0HDVXUHWLPH
'!0'03
Figure 24 and 25 show SVR and OUTPUT waveforms at the turn-on (stand-by out) with and
without turn-on diagnostic.
Figure 24. SVR and output behavior (Case 1: without turn-on diagnostic)
6SVR
/UT
0ERMANENTDIAGNOSTIC
ACQUISITIONTIMEMS4YP
T
"IASPOWER AMPT URN
ON
$IAGNOSTIC %NABLE
0ERMANENT
)#"$!4!
&!5,4
EVENT
0ERMANENT$IAGNOSTICSDATAOUPUT
PERMITTEDTIME
DocID023498 Rev 9
2EAD$ATA
'!0'03
17/41
40
Diagnostics functional description
TDA7569BLV
Figure 25. SVR and output pin behavior (Case 2: with turn-on diagnostic)
6SVR
/UT
4U RN
OND IAGNOSTIC
ACQU ISI TIONTIM EMS 4YP
0ERMANENTDIAGN OST IC
ACQUI SIT IONTIMEMS 4YP
T
4URN
ON $IAGN OST ICS DATAOUT PU T
PER MITT EDTI ME
$IAGNOST IC%NABLE
4UR N
ON
"IASPOWERAMP TURN
ON
PERMITTE DT IME
$IAGN OST IC% NABLE
0ERMAN ENT
2EAD$ATA
&!5,4
EVENT
0ERMANENT$IAGNO ST ICS DAT AOUT PUT
PERMITTE DTIME
)#"$!4!
'!0'03
The information related to the outputs status is read and memorized at the end of the
current pulse plateau. The acquisition time is 100 ms (typ.). No audible noise is generated in
the process. As for SHORT TO GND / Vs the fault-detection thresholds remain unchanged
from 26 dB to 16 dB gain setting. They are as follows:
Figure 26. Short circuit detection thresholds
3#TO'.$
6
X
6
.ORMAL/PERATION
6
X
63
6
3#TO6S
63
6
63
'!0'03
Concerning SHORT ACROSS THE SPEAKER / OPEN SPEAKER, the threshold varies
from 26 dB to 16 dB gain setting, since different loads are expected (either normal speaker's
impedance or high impedance). The values in case of 26 dB gain are as follows:
Figure 27. Load detection thresholds - high gain setting
3#ACROSS,OAD
6
X
7
.ORMAL/PERATION
7
X
/PEN,OAD
7
7
)NFINITE
'!0'03
If the Line-Driver mode (Gv= 16 dB and Line Driver Mode diagnostic = 1) is selected, the
same thresholds will change as follows:
Figure 28. Load detection threshold - low gain setting
3#ACROSS,OAD
7
7
X
.ORMAL/PERATION
7
7
X
/PEN,OAD
7
INFINITE
'!0'03
18/41
DocID023498 Rev 9
TDA7569BLV
4.2
Diagnostics functional description
Permanent diagnostics
Detectable conventional faults are:
–
Short to GND
–
Short to Vs
–
Short across the speaker
The following additional feature is provided:
–
Output offset detection
The TDA7569BLV has 2 operating status:
1. RESTART mode. The diagnostic is not enabled. Each audio channel operates
independently of each other. If any of the a.m. faults occurs, only the channel(s)
interested is shut down. A check of the output status is made every 1 ms (Figure 29).
Restart takes place when the overload is removed.
2. DIAGNOSTIC mode. It is enabled via I2C bus and it self activates if an output overload
(such as to cause the intervention of the short-circuit protection) occurs to the speakers
outputs. Once activated, the diagnostics procedure develops as follows (Figure 30):
–
To avoid momentary re-circulation spikes from giving erroneous diagnostics, a
check of the output status is made after 1ms: if normal situation (no overloads) is
detected, the diagnostic is not performed and the channel returns active.
–
Instead, if an overload is detected during the check after 1 ms, then a diagnostic
cycle having a duration of about 100 ms is started.
–
After a diagnostic cycle, the audio channel interested by the fault is switched to
RESTART mode. The relevant data are stored inside the device and can be read
by the microprocessor. When one cycle has terminated, the next one is activated
by an I2C reading. This is to ensure continuous diagnostics throughout the carradio operating time.
–
To check the status of the device a sampling system is needed. The timing is
chosen at microprocessor level (over half a second is recommended).
Figure 29. Restart timing without diagnostic enable (permanent) - Each 1 mS time, a
sampling of the fault is done
/UT
M3
M3
M3
M3
M3
T
/VERCUR RENTAND SHOR T
CIRCUIT PROTECT IONI NTERVENT ION
IESHOR TCIRCUI TT O'.$
3HOR TCI RCUI TREMOVED
'!0'03
Figure 30. Restart timing with diagnostic enable (permanent)
M3
M3
M3
M3
T
/VERCURRENT ANDSHORT
CIRCUITPROTECTI ON IN TERVENTI ON
IES HORTC IRCUI TTO'.$
3HO RTCIRCUIT REMOVED
'!0'03
DocID023498 Rev 9
19/41
40
Diagnostics functional description
4.3
TDA7569BLV
Output DC offset detection
Any DC output offset exceeding ±2 V is signalled out. This inconvenient might occur as a
consequence of initially defective or aged and worn-out input capacitors feeding a DC
component to the inputs, so putting the speakers at risk of overheating.
This diagnostic has to be performed with low-level output AC signal (or Vin = 0).
The test is run with selectable time duration by microprocessor (from a "start" to a "stop"
command):
–
START = Last reading operation or setting IB1 - D5 - (OFFSET enable) to 1
–
STOP = Actual reading operation
Excess offset it is signalled out if persistent for all the assigned testing time. This feature is
disabled if any overloads leading to activation of the short-circuit protection occurs in the
process.
4.4
AC diagnostic
This function is design to detect accidental disconnection of tweeters in 2-way speaker and,
more in general, presence of capacitive (AC) coupled loads.
This diagnostic is based on the notion that the overall speaker's impedance (woofer +
parallel tweeter) will tend to increase towards high frequencies if the tweeter gets
disconnected, because the remaining speaker (woofer) would be out of its operating range
(high impedance). The diagnostic decision is made according to peak output current
thresholds, and it is enabled by setting (IB2-D2) = 1. Two different detection levels are
available:
–
High current threshold IB2 (D7) = 0
Iout > 500 mApk = normal status
Iout < 250 mApk = open tweeter
–
Low current threshold IB2 (D7) = 1
Iout > 250 mApk = normal status
Iout < 125 mApk = open tweeter
To correctly implement this feature, it is necessary to briefly provide a signal tone (with the
amplifier in "play") whose frequency and magnitude are such as to determine an output
current higher than 500 mApk with IB2(D7) = 0 (higher than 250 mApk with IB2(D7) = 1) in
normal conditions and lower than 250 mApk with IB2(D7) = 0 (lower than 125 mApk with
IB2(D7)=1) should the parallel tweeter be missing.
The test has to last for a minimum number of 3 sine cycles starting from the activation of the
AC diagnostic function IB2) up to the I2C reading of the results (measuring period). To
confirm presence of tweeter, it is necessary to find at least 3 current pulses over the above
threadless over all the measuring period, else an "open tweeter" message will be issued.
The frequency / magnitude setting of the test tone depends on the impedance
characteristics of each specific speaker being used, with or without the tweeter connected
(to be calculated case by case). High-frequency tones (> 10 kHz) or even ultrasonic signals
are recommended for their negligible acoustic impact and also to maximize the impedance
module's ratio between with tweeter-on and tweeter-off.
Figure 31 and 32 shows the load impedance as a function of the peak output voltage and
the relevant diagnostic fields.
20/41
DocID023498 Rev 9
TDA7569BLV
Diagnostics functional description
It is recommended to keep output voltage always below 8 V (high threshold) or 4 V (low
threshold) to avoid the circuit to saturate (causing wrong detection cases).
This feature is disabled if any overloads leading to activation of the short-circuit protection
occurs in the process.
Figure 31. Current detection high: load impedance |Z| vs. output peak voltage
,O AD\Z\/HM
)OUTPEAK M!
,OWCURRENTDETECTIONAREA
/PENLOAD
$OFTHE$"XBYRES
)OUTPEAK M!
)"$
(IGHCURRENTDETECTIONAREA
.ORMALLOAD
$OFTHE$"XBYTES
6OUT 0EAK
'!0'03
Figure 32. Current detection low: load impedance |Z| vs. output peak voltage
,OAD\Z\/HM
)OUTPEAK M!
,OWCURRENTDETECTIONAREA
/PENLOAD
$OFTHE$"XBYRES
)OUTPEAK M!
)"$
(IGHCURRENTDETECTIONAREA
.ORMALLOAD
$OFTHE$"XBYTES
6OUT0EAK
DocID023498 Rev 9
'!0'03
21/41
40
Multiple faults
5
TDA7569BLV
Multiple faults
When more misconnections are applied simultaneously at the audio outputs, it is
guaranteed that at least one of them is initially read out. The others are notified after
successive cycles of I2C reading and faults removal, provided that the diagnostic is enabled.
This is true for both kinds of diagnostic (Turn on and Permanent).
The table below shows all the couples of double-fault possible. It should be taken into
account that a short circuit with the 4 ohm speaker unconnected is considered as double
fault.
Table 5. Double fault table for turn-on diagnostic
S. GND
S. Vs
S. Across L.
Open L.
S. GND
S. GND
S. Vs + S. GND
S. GND
S. GND
S. Vs
/
S. Vs
S. Vs
S. Vs
S. Across L.
/
/
S. Across L.
N.A.
Open L.
/
/
/
Open L. (*)
In Permanent Diagnostic the table is the same, with only a difference concerning Open
Load (*), which is not among the recognizable faults. Should an Open Load be present
during the device's normal working, it would be detected at a subsequent Turn on
Diagnostic cycle (i.e. at the successive Car Radio Turn on).
5.1
Faults availability
All the results coming from I2C bus, by read operations, are the consequence of
measurements inside a defined period of time. If the fault is stable throughout the whole
period, it will be sent out.
To guarantee always resident functions, every kind of diagnostic cycles (Turn on,
Permanent, Offset) will be reactivate after any I2C reading operation. So, when the micro
reads the I2C, a new cycle will be able to start, but the read data will come from the previous
diag. cycle (i.e. The device is in Turn On state, with a short to Gnd, then the short is
removed and micro reads I2C. The short to Gnd is still present in bytes, because it is the
result of the previous cycle. If another I2C reading operation occurs, the bytes do not show
the short). In general to observe a change in Diagnostic bytes, two I2C reading operations
are necessary.
22/41
DocID023498 Rev 9
TDA7569BLV
6
Thermal protection
Thermal protection
Thermal protection is implemented through thermal foldback (Figure 33).
Thermal foldback begins limiting the audio input to the amplifier stage as the junction
temperatures rise above the normal operating range. This effectively limits the output power
capability of the device thus reducing the temperature to acceptable levels without totally
interrupting the operation of the device.
The output power will decrease to the point at which thermal equilibrium is reached.
Thermal equilibrium will be reached when the reduction in output power reduces the
dissipated power such that the die temperature falls below the thermal foldback threshold.
Should the device cool, the audio level will increase until a new thermal equilibrium is
reached or the amplifier reaches full power. Thermal foldback will reduce the audio output
level in a linear manner.
Three thermal warning are available through the I2C bus data. After thermal shut down
threshold is reached, the CD could toggle (as shown in Figure 33) or stay low, depending on
signal level.
Figure 33. Thermal foldback diagram
6OUT
6OUT
4(7!2.
4(7! 2.
4(7!2.
/.
/.
/.
4(3(
34!24
43$
#$OUT
3$
4(3(
%.$
WITHSAMEINPUT
SIGNAL
4J #
4J #
4J #
6.1
'!0'03
Fast muting
The muting time can be shortened to less than 1.5ms by setting (IB2) D5 = 1. This option
can be useful in transient battery situations (i.e. during car engine cranking) to quickly
turnoff the amplifier to avoid any audible effects caused by noise/transients being injected
by preamp stages. The bit must be set back to “0” shortly after the mute transition.
DocID023498 Rev 9
23/41
40
Battery transitions management
TDA7569BLV
7
Battery transitions management
7.1
Low voltage operation (“start stop”)
The most recent OEM specifications are requiring automatic stop of car engine at traffic
light, in order to reduce emissions of polluting substances. The TDA7569BLV, thanks to its
innovating design, allows a continuous operation when battery falls down to 6/7V during
such conditions, without producing pop noise. The maximum system power will be reduced
accordingly.
Worst case battery cranking curves are shown below, indicating the shape and durations of
allowed battery transitions.
Figure 34. Worst case battery cranking curve sample 1
9EDWW9
9
9
9
9
W
W
W
W W
W
W
WV
*$3*36
V1 = 12 V; V2 = 6 V; V3 = 7 V; V4 = 8 V
t1 = 2 ms; t2 = 50 ms; t3 = 5 ms; t4 = 300 ms; t5 =10 ms; t6 = 1 s; t7 = 2 ms
Figure 35. Worst case battery cranking curve sample 2
9EDWW 9
9
9
9
W
W
W
W
V1 = 12 V; V2 = 6 V; V3 = 7 V
t1 = 2 ms; t2 = 5 ms; t3 = 15 ms; t5 = 1 s; t6 = 50 ms
24/41
DocID023498 Rev 9
W
WV
*$3*36
TDA7569BLV
7.2
Battery transitions management
Advanced battery management
In addition to compatibility with low Vbatt, the TDA7569BLV is able to sustain upwards fast
battery transitions (like the one showed in Figure 36) without causing unwanted audible
effect, thanks to the innovative circuit topology.
Figure 36. Upwards fast battery transitions diagram
'!0'03
DocID023498 Rev 9
25/41
40
Application suggestion
TDA7569BLV
8
Application suggestion
8.1
Inputs impedance matching
Figure 37. Inputs impedance matching circuit
)N
6). 0LAY
6!#
'.$
'
!#'.$
0K7
K7
362CHARGE
CIRCUIT
362
'!0'03
The above is a simplified input stage where it is visible that the AC-GND impedance (60 kΩ)
is the same as the input one.
During battery variations the SVR voltage is moved and VIN and VAC-GND tracks it through
the two R-C networks.
Any differences of this two time constants can produce a differential input voltage, which can
produce a noise.
Consequently, any additional passive components at the inputs (other than the input
capacitors) such as series resistance or R dividers must be compensated for at AC-GND
level by connecting the same equivalent resistance in series to CAC-GND.
A good 1:1 matching (ZAC-GND = ZIN) is therefore recommended to minimize pop. This rule
applies to both "4-CH operation" and "2-CH operation", as any unused input has be ACgrounded (through the same CIN value).
26/41
DocID023498 Rev 9
TDA7569BLV
8.2
Application suggestion
High efficiency introduction
Thanks to its operating principle, the TDA7569BLV obtains a substantial reduction of power
dissipation from traditional class-AB amplifiers without being affected by the massive
radiation effects and complex circuitry normally associated with class-D solutions.
The high efficiency operating principle is based on the use of bridge structures which are
connected by means of a power switch. In particular, as shown in Figure 2, Ch1 is linked to
Ch2, while Ch3 to Ch4. The switch, controlled by a logic circuit which senses the input
signals, is closed at low volumes (output power steadily lower than 2.5 W) and the system
acts like a "single bridge" with double load. In this case, the total power dissipation is a
quarter of a double bridge.
Due to its structure, the highest efficiency level can be reached when symmetrical loads are
applied on channels sharing the same switch.
Figure 38. High efficiency - basic structure
&0
2-
n
)?&
)?2
2EAR
&RONT
6IN&
6IN2
20
&n
)?20
&
CHANNEL
(IGH
IMPEDANCE
2
CHANNEL
#/.42/,
,/')#
"UFFER
'!0'03
When the power demand increases to more than 2.5 W, the system behavior is switched
back to a standard double bridge in order to guarantee the maximum output power, while in
the 6 V start-stop devices the High Efficiency mode is automatically disabled at low VCC
(7.3 V ± 0.3 V). No need to re-program it when VCC goes back to normal levels.
The results show (Figure 19) that in the range 2-4 W (@ VCC = 14.4 V, RL = 4Ω), with the
High Efficiency mode, the dissipated power gets up to 50 % less than the value obtained
with the standard mode.
DocID023498 Rev 9
27/41
40
I2C bus
TDA7569BLV
9
I2C bus
9.1
I2C programming/reading sequences
A correct turn on/off sequence with respect to the diagnostic timings and producing no
audible noises could be as follows (after battery connection):
–
TURN-ON: PIN2 > 4.5V --- 10 ms --- (STAND-BY OUT + DIAG ENABLE) --- 1 s
(min) --- MUTING OUT
–
TURN-OFF: MUTING IN - wait for 50 ms - HW ST-BY IN (ST-BY pin ≤ 1.2 V)
–
Car Radio Installation: PIN2 > 4.5 V --- 10ms DIAG ENABLE (write) --- 200 ms --I2C read (repeat until All faults disappear).
–
OFFSET TEST: Device in Play (no signal) -- OFFSET ENABLE - 30 ms - I2C
reading (repeat I2C reading until high-offset message disappears).
9.2
Address selection and I2C disable
When the ADSEL/I2CDIS pin is left open the I2C bus is disabled and the device can be
controlled by the STBY/MUTE pin.
In this status (no - I2C bus) the CK pin enables the HIGH-EFFICIENCY MODE (0 = STD
MODE; 1 = HE MODE) and the DATA pin sets the gain (0 = 26 dB; 1 = 16 dB).
When the ADSEL/I2CDIS pin is connected to GND the I2C bus is active with address
.
To select the other I2C address a resistor must be connected to ADSEL/I2CDIS pin as
following:
0 < R < 1 kΩ: I2C bus active with address
11 kΩ < R < 21 kΩ: I2C bus active with address
40 kΩ < R < 70 kΩ: I2C bus active with address
R > 120 kΩ: Legacy mode
(x: read/write bit sector)
9.3
I2C bus interface
Data transmission from microprocessor to the TDA7569BLV and viceversa takes place
through the 2 wires I2C bus interface, consisting of the two lines SDA and SCL (pull-up
resistors to positive supply voltage must be connected).
9.3.1
Data validity
As shown by Figure 39, the data on the SDA line must be stable during the high period of
the clock. The HIGH and LOW state of the data line can only change when the clock signal
on the SCL line is LOW.
28/41
DocID023498 Rev 9
I2C bus
TDA7569BLV
9.3.2
Start and stop conditions
As shown by Figure 40 a start condition is a HIGH to LOW transition of the SDA line while
SCL is HIGH. The stop condition is a LOW to HIGH transition of the SDA line while SCL is
HIGH.
9.3.3
Byte format
Every byte transferred to the SDA line must contain 8 bits. Each byte must be followed by an
acknowledge bit. The MSB is transferred first.
9.3.4
Acknowledge
The transmitter* puts a resistive HIGH level on the SDA line during the acknowledge clock
pulse (see Figure 41). The receiver** has to pull-down (LOW) the SDA line during the
acknowledge clock pulse, so that the SDA line is stable LOW during this clock pulse.
* Transmitter
–
master (μP) when it writes an address to the TDA7569BLV
–
slave (TDA7569BLV) when the μP reads a data byte from TDA7569BLV
** Receiver
–
slave (TDA7569BLV) when the μP writes an address to the TDA7569BLV
–
master (μP) when it reads a data byte from TDA7569BLV
Figure 39. Data validity on the I2C bus
3$!
3#,
$!4!,).%
34!",%$!4!
6!,)$
#(!.'%
$!4!
!,,/7%$
'!0'03
Figure 40. Timing diagram on the I2C bus
3#,
)#"53
3$!
34!24
34/0
'!0'03
Figure 41. Acknowledge on the I2C bus
3#,
3$!
-3"
!#+./7,%$'-%.4
&2/-2%#%)6%2
34!24
DocID023498 Rev 9
'!0'03
29/41
40
Software specifications
10
TDA7569BLV
Software specifications
All the functions of the TDA7569BLV are activated by I2C interface.
The bit 0 of the "ADDRESS BYTE" defines if the next bytes are write instruction (from μP to
TDA7569BLV) or read instruction (from TDA7569BLV to μP).
Chip address
D7
1
D0
1
0
1
1
(*)
(*)
X = 0 Write to device
X = 1 Read from device
If R/W = 0, the P sends 2 "Instruction Bytes": IB1 and IB2.
(*) address selector bit, please refer to address selection description on Chapter 9.2.
Table 6. IB1
Bit
30/41
Instruction decoding bit
D7
Supply transition mute threshold high (D7 = 1)
Supply transition mute threshold low (D7 = 0)
D6
Diagnostic enable (D6 = 1)
Diagnostic defeat (D6 = 0)
D5
Offset Detection enable (D5 = 1)
Offset Detection defeat (D5 = 0)
D4
Front Channel (CH1, CH3)
Gain = 26 dB (D4 = 0)
Gain = 16 dB (D4 = 1)
D3
Rear Channel (CH2, CH4)
Gain = 26 dB (D3 = 0)
Gain = 16 dB (D3 = 1)
D2
Mute front channels (D2 = 0)
Unmute front channels (D2 = 1)
D1
Mute rear channels (D1 = 0)
Unmute rear channels (D1 = 1)
D0
CD 2% (D0 = 0)
CD 10% (D0 = 1)
DocID023498 Rev 9
X
D8 Hex
TDA7569BLV
Software specifications
Table 7. IB2
Bit
Instruction decoding bit
D7
Current detection threshold
High th (D7 = 0)
Low th (D7 =1)
D6
0
D5
Normal muting time (D5 = 0)
Fast muting time (D5 = 1)
D4
Stand-by on - Amplifier not working - (D4 = 0)
Stand-by off - Amplifier working - (D4 = 1)
D3
Power amplifier mode diagnostic (D3 = 0)
Line driver mode diagnostic (D3 = 1)
D2
Current Detection Diagnostic Enabled (D2 =1)
Current Detection Diagnostic Defeat (D2 =0)
D1
Right Channel Power amplifier working in standard mode (D1 = 0)
Power amplifier working in high efficiency mode (D1 = 1)
D0
Left Channel Power amplifier working in standard mode (D0 = 0)
Power amplifier working in high efficiency mode (D0 = 1)
If R/W = 1, the TDA7569BLV sends 4 "Diagnostics Bytes" to P: DB1, DB2, DB3 and DB4.
Table 8. DB1
Bit
Instruction decoding bit
D7
Thermal warning 1 active (D7 = 1), Tj =160 °C
-
D6
Diag. cycle not activated or not terminated (D6 = 0)
Diag. cycle terminated (D6 = 1)
-
D5
Channel LF (CH1)
Current detection IB2 (D7) = 0
Output peak current < 250 mA - Open load (D5 = 1)
Output peak current > 500 mA - Normal load (D5 = 0)
Channel LF (CH1)
Current detection IB2 (D7) = 1
Output peak current < 125 mA - Open load (D5 = 1)
Output peak current > 250 mA - Normal load (D5 = 0)
D4
Channel LF (CH1)
Turn-on diagnostic (D4 = 0)
Permanent diagnostic (D4 = 1)
-
D3
Channel LF (CH1)
Normal load (D3 = 0)
Short load (D3 = 1)
-
D2
Channel LF (CH1)
Turn-on diag.: No open load (D2 = 0)
Open load detection (D2 = 1)
Offset diag.: No output offset (D2 = 0)
Output offset detection (D2 = 1)
-
DocID023498 Rev 9
31/41
40
Software specifications
TDA7569BLV
Table 8. DB1 (continued)
Bit
Instruction decoding bit
D1
Channel LF (CH1)
No short to Vcc (D1 = 0)
Short to Vcc (D1 = 1)
-
D0
Channel LF (CH1)
No short to GND (D1 = 0)
Short to GND (D1 = 1)
-
Table 9. DB2
Bit
Instruction decoding bit
D7
Offset detection not activated (D7 = 0)
Offset detection activated (D7 = 1)
-
D6
X
-
D5
Channel LR (CH2)
Current detection IB2 (D7) = 0
Output peak current < 250 mA - Open load (D5 = 1)
Output peak current > 500 mA - Normal load (D5 = 0)
Channel LR (CH2)
Current detection IB2 (D7) = 1
Output peak current < 125 mA - Open load (D5 = 1)
Output peak current > 250 mA - Normal load (D5 = 0)
D4
Channel LR (CH2)
Turn-on diagnostic (D4 = 0)
Permanent diagnostic (D4 = 1)
-
D3
Channel LR (CH2)
Normal load (D3 = 0)
Short load (D3 = 1)
-
D2
Channel LR (CH2)
Turn-on diag.: No open load (D2 = 0)
Open load detection (D2 = 1)
Permanent diag.: No output offset (D2 = 0)
Output offset detection (D2 = 1)
-
D1
Channel LR (CH2)
No short to Vcc (D1 = 0)
Short to Vcc (D1 = 1)
-
D0
Channel LR (CH2)
No short to GND (D1 = 0)
Short to GND (D1 = 1)
-
32/41
DocID023498 Rev 9
TDA7569BLV
Software specifications
Table 10. DB3
Bit
Instruction decoding bit
D7
Standby status (= IB2 - D4)
-
D6
Diagnostic status (= IB1 - D6)
-
D5
Channel RF (CH3)
Current detection IB2 (D7) = 0
Output peak current < 250 mA - Open load (D5 = 1)
Output peak current > 500 mA - Normal load (D5 = 0)
Channel RF (CH3)
Current detection IB2 (D7) = 1
Output peak current < 125 mA - Open load (D5 = 1)
Output peak current > 250 mA - Normal load (D5 = 0)
D4
Channel RF (CH3)
Turn-on diagnostic (D4 = 0)
Permanent diagnostic (D4 = 1)
-
D3
Channel RF (CH3)
Normal load (D3 = 0)
Short load (D3 = 1)
-
D2
Channel RF (CH3)
Turn-on diag.: No open load (D2 = 0)
Open load detection (D2 = 1)
Permanent diag.: No output offset (D2 = 0)
Output offset detection (D2 = 1)
-
D1
Channel RF (CH3)
No short to Vcc (D1 = 0)
Short to Vcc (D1 = 1)
-
D0
Channel RF (CH3)
No short to GND (D1 = 0)
Short to GND (D1 = 1)
-
DocID023498 Rev 9
33/41
40
Software specifications
TDA7569BLV
Table 11. DB4
Bit
Instruction decoding bit
D7
Thermal warning 2 active (D7 = 1), Tj = 145 °C
-
D6
Thermal warning 3 active (D6 = 1) Tj = 125 °C
-
D5
Channel RR (CH4)
Current detection IB2 (D7) = 0
Output peak current < 250 mA - Open load (D5 = 1)
Output peak current > 500 mA - Normal load (D5 = 0)
Channel RR (CH4)
Current detection IB2 (D7) = 1
Output peak current < 125 mA - Open load (D5 = 1)
Output peak current > 250 mA - Normal load (D5 = 0)
D4
Channel RR (CH4)
Turn-on diagnostic (D4 = 0)
Permanent diagnostic (D4 = 1)
-
D3
Channel R (CH4)
R Normal load (D3 = 0)
Short load (D3 = 1)
-
D2
Channel RR (CH4)
Turn-on diag.: No open load (D2 = 0)
Open load detection (D2 = 1)
Permanent diag.: No output offset (D2 = 0)
Output offset detection (D2 = 1)
-
D1
Channel RR (CH4)
No short to Vcc (D1 = 0)
Short to Vcc (D1 = 1)
-
D0
Channel RR (CH4)
No short to GND (D1 = 0)
Short to GND (D1 = 1)
-
34/41
DocID023498 Rev 9
TDA7569BLV
11
Examples of bytes sequence
Examples of bytes sequence
1 - Turn-On diagnostic - Write operation
Start
Address byte with D0 = 0
ACK
IB1 with D6 = 1
ACK
IB2
ACK
STOP
2 - Turn-On diagnostic - Read operation
Start Address byte with D0 = 1 ACK
DB1 ACK
DB2 ACK DB3 ACK DB4 ACK STOP
The delay from 1 to 2 can be selected by software, starting from 1ms
3a - Turn-On of the power amplifier with 26dB gain, mute on, diagnostic defeat, CD = 2%
.
Start
Address byte with D0 = 0
ACK
IB1
ACK
X0000000
IB2
ACK
STOP
ACK
STOP
ACK
STOP
XXX1XX11
3b - Turn-Off of the power amplifier
Start
Address byte with D0 = 0
ACK
IB1
ACK
X0XXXXXX
IB2
XXX0XXXX
4 - Offset detection procedure enable
Start
Address byte with D0 = 0
ACK
IB1
ACK
XX1XX11X
IB2
XXX1XXXX
5 - Offset detection procedure stop and reading operation (the results are valid only for the
offset detection bits (D2 of the bytes DB1, DB2, DB3, DB4)
.
Start Address byte with D0 = 1 ACK DB1 ACK
DB2 ACK
DB3 ACK DB4 ACK STOP
The purpose of this test is to check if a D.C. offset (2 V typ.) is present on the outputs,
produced by input capacitor with anomalous leakage current or humidity between pins.
The delay from 4 to 5 can be selected by software, starting from 1ms
DocID023498 Rev 9
35/41
40
Package information
12
TDA7569BLV
Package information
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Figure 42. Flexiwatt27 (horizontal) mechanical data and package dimensions
',0
$
%
&
'
(
)
*
*
+
+
+
+
/
/
/
/
/
/
/
0
0
0
1
3
5
5
5
5
5
9
9
9
9
PP
7