TL062BCDT

TL062, TL062A, TL062B Low-power JFET dual operational amplifiers Datasheet − production data Features ■ Very low power consumption: 200 µA ■ Wide common-mode (up to VCC+) and differential voltage ranges ■ Low input bias and offset currents ■ Output short-circuit protection ■ High input impedance JFET input stage ■ Internal frequency compensation ■ Latch up free operation ■ High slew rate: 3.5 V/µs N DIP8 (plastic package) D SO-8 (plastic micropackage) Description The TL062, TL062A and TL062B devices are high-speed JFET input single operational amplifiers. Each of these JFET input operational amplifiers incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and a low offset voltage temperature coefficient. Pin connections (top view) 1 8 2 - 3 + 4 1 2 3 4 5 6 7 8 September 2012 This is information on a product in full production. Doc ID 2294 Rev 4 7 - 6 + 5 - Output 1 - Inverting input 1 - Non-inverting input 1 - VCC- Non-inverting input 2 - Inverting input 2 - Output 2 - VCC+ 1/15 www.st.com 15 Schematic diagram TL062, TL062A, TL062B 1 Schematic diagram Figure 1. Schematic diagram 2/15 Doc ID 2294 Rev 4 TL062, TL062A, TL062B 2 Absolute maximum ratings and operating conditions Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol VCC Vi Parameter Unit ±18 V ±15 V ±30 V 680 mW Supply voltage(1) Input voltage (2) Vid Differential input voltage Ptot Power dissipation Output short-circuit Tstg Value (3) duration(4) Infinite Storage temperature range °C (5) (6) Rthja Thermal resistance junction-to-ambient , SO-8 DIP8 125 85 °C/W Rthjc Thermal resistance junction-to-case(5),(6) SO-8 DIP8 40 41 °C/W HBM: human body model(7) 900 V 150 V 1.5 kV ESD MM: machine model(8) CDM: charged device model(9) 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-. 2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 5. Short-circuits can cause excessive heating and destructive dissipation. 6. Rth are typical values. 7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: a 200 pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to ground. Table 2. Symbol Operating conditions Parameter VCC Supply voltage range Toper Operating free air temperature range TL062I, AI, BI TL062C, AC, BC 6 to 36 Doc ID 2294 Rev 4 -40 to +105 Unit V 0 to +70 °C 3/15 Electrical characteristics TL062, TL062A, TL062B 3 Electrical characteristics Table 3. VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) TL062I Symbol TL062C Parameter Unit Min. Typ. Max. Input offset voltage (RS = 50 Ω) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 3 6 9 Temperature coefficient of input offset voltage (R S = 50 Ω) 10 Iio Input offset current(1) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 5 100 10 5 200 5 pA nA Iib Input bias current(1) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 30 200 20 30 400 10 pA nA Vio DVio Input common mode voltage range ±11.5 Vopp Output voltage swing (R L = 10 kΩ) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 20 20 27 Avd Large signal voltage gain RL = 10 kΩ, Vo = ±10 V, Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 4 4 6 GBP Ri Gain bandwidth product Tamb = +25 °C, RL =10 kΩ, CL = 100 pF Input resistance Typ. Max. 3 15 20 mV μV/°C 10 +15 -12 Vicm Min. +15 -12 V 20 20 27 V 3 3 6 ±11.5 V/mV 1 1 MHz 1012 1012 Ω CMR Common mode rejection ratio RS = 50 Ω 80 86 70 76 dB SVR Supply voltage rejection ratio RS = 50 Ω 80 95 70 95 dB ICC Vo1/Vo2 Supply current, no load Tamb = +25 °C, no load, no signal 200 Channel separation Av = 100, Tamb = 25 °C 120 PD Total power consumption Tamb = +25 °C, no load, no signal SR Slew rate Vi = 10 V, RL = 10 kΩ, CL= 100 pF, Av = 1 4/15 6 1.5 Doc ID 2294 Rev 4 3.5 250 200 250 120 7.5 6 1.5 3.5 μA dB 7.5 mW V/μs TL062, TL062A, TL062B Table 3. Electrical characteristics VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) (continued) TL062I Symbol TL062C Parameter Unit Min. Typ. Max. Min. Typ. Max. Rise time Vi = 20 mV, RL = 10 kΩ, CL = 100 pF, Av = 1 0.2 0.2 μs Kov Overshoot factor (see Figure 15) Vi = 20 mV, RL = 10 kΩ, CL = 100 pF, Av = 1 10 10 % en Equivalent input noise voltage RS = 100 Ω, f = 1 kHz 42 42 nV -----------Hz tr 1. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. Table 4. VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) TL062AC, AI Symbol TL062BC, BI Parameter Unit Min. Typ. Max. Input offset voltage (RS = 50 Ω) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 3 3 7.5 Temperature coefficient of input offset voltage (RS = 50 Ω) 10 Iio Input offset current(1) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 5 100 3 5 100 3 pA nA Iib Input bias current(1) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 30 200 7 30 200 7 nA Vio DVio Max. 2 3 5 10 +15 -12 ±11.5 +15 -12 Output voltage swing (RL = 10 kΩ) Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 20 20 27 20 20 27 Large signal voltage gain RL = 10 kΩ, Vo = ±10 V, Tamb = +25 °C Tmin ≤ Tamb ≤ Tmax 4 4 6 4 4 6 Input common mode voltage range Vopp Avd Ri Typ. ±11.5 Vicm GBP Min. Gain bandwidth product Tamb = +25 °C, RL =10 kΩ, CL = 100 pF Input resistance mV µV/°C V V/mV 1 1 MHz 1012 1012 Ω CMR Common mode rejection ratio RS = 50 Ω 80 86 80 86 dB SVR Supply voltage rejection ratio RS = 50 Ω 80 95 80 95 dB Doc ID 2294 Rev 4 5/15 Electrical characteristics Table 4. TL062, TL062A, TL062B VCC = ±15 V, Tamb = +25 °C (unless otherwise specified) (continued) TL062AC, AI Symbol Unit Min. ICC Vo1/Vo2 TL062BC, BI Parameter Typ. Max. Supply current, no load Tamb = +25 °C, no load, no signal 200 250 Channel separation Av = 100, Tamb = +25 °C 120 PD Total power consumption Tamb = +25 °C, no load, no signal SR Slew rate Vi = 10 V, RL = 10 kΩ, CL = 100 pF, Av = 1 6 1.5 3.5 Min. Typ. Max. 200 250 µA 7.5 mW 120 7.5 6 1.5 3.5 V/μs tr Rise time Vi = 20 mV, R L = 10 kΩ, CL = 100 pF, Av = 1 0.2 0.2 μs Kov Overshoot factor (see Figure 15) Vi = 20 mV, R L = 10 kΩ, CL = 100 pF, Av = 1 10 10 % en Equivalent input noise voltage RS = 100 Ω, f = 1 kHz 42 42 nV -----------Hz 1. The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. 6/15 Doc ID 2294 Rev 4 TL062, TL062A, TL062B Figure 3. Maximum peak-to-peak output voltage versus free air temperature Maximum peak-to-peak output voltage (V) Maximum peak-to-peak output voltage versus supply voltage Maximum peak-to-peak output voltage (V) Figure 2. Electrical characteristics RL = 10 kΩ Tamb = + 25 °C VCC = +/- 15 V RL = 10 kΩ Free air temperature (°C) Supply voltage (V) Figure 5. Maximum peak-to-peak output voltage versus frequency Maximum peak-to-peak output voltage (V) Maximum peak-to-peak output voltage versus load resistance Maximum peak-to-peak output voltage (V) Figure 4. VCC = +/- 15 V Tamb = + 25 °C VCC = +/- 12 V VCC = +/- 5 V VCC = +/- 2 V Frequency (Hz) Load resistance (kΩ) Differential voltage amplification versus free air temperature Figure 7. Large signal differential voltage amplification and phase shift versus frequency 10 6 10 7 105 Differential voltage amplification (V/V) Differential voltage amplification (V/mV) Figure 6. RL = 10 kΩ Tamb = + 25 °C VCC = +/- 15 V 4 2 VCC = +/- 15 V RL = 10 kΩ VCC = +/- 5 V to +/- 15 V RL = 2 kΩ Tamb = + 25 °C Differential voltage amplification (left scale) 4 10 3 10 102 101 -50 -25 0 25 50 75 100 125 Free air temperature (°C) 1 45 90 Phase shift (right scale) 135 1 -75 0 10 100 1k 10k 100k 1M 180 10M Frequency (Hz) Doc ID 2294 Rev 4 7/15 Electrical characteristics TL062, TL062A, TL062B 250 250 200 200 Supply current (μA) Supply current per amplifier versus Figure 9. supply voltage Supply current (μA) Figure 8. 150 100 Tamb = + 25 °C No signal no load 50 Supply current per amplifier versus free air temperature 150 100 VCC = +/- 15 V 50 No signal no load 0 0 0 2 4 6 8 10 12 14 -75 16 -50 Figure 10. Total power dissipated versus free air temperature 20 No signal no load 15 10 5 0 -75 -50 -25 0 25 50 75 50 25 100 125 75 Figure 11. Common-mode rejection ratio versus free air temperature Common mode rejection ratio (dB) Total power dissipated (mW) 30 VCC = +/- 15 V 0 Free air temperature (°C) Supply voltage (+/- V) 25 -25 100 87 86 85 84 83 VCC = +/- 15 V 82 81 -75 125 RL = 10 kΩ -50 -25 0 25 50 75 100 125 Free air temperature (°C) Free air temperature (°C) Figure 12. Normalized unity gain bandwidth slew rate and phase shift versus temperature Figure 13. Input bias current versus free air temperature Unity-gain bandwidth (left scale) 1.1 Slew rate (left scale) 1 0.9 0.8 1.03 1.02 1.01 1 0.99 VCC = +/- 15 V RL = 10 kΩ 0.98 f = B1 for phase shift 0.7 -75 -50 -25 0 25 50 0.97 75 100 125 Input bias current (nA) 1.2 Phase shift (right scale) Normalized phase shift Normalized unity-gain bandwidth and slew rate 100 1.3 VCC = +/- 15 V 10 1 0.1 0.01 -50 -25 0 25 50 75 Free air temperature (°C) Free air temperature (°C) 8/15 Doc ID 2294 Rev 4 100 125 TL062, TL062A, TL062B Electrical characteristics Figure 15. Output voltage versus elapsed time 6 28 24 Input 4 2 Output voltage (mV) Input and output voltages (V) Figure 14. Voltage follower large signal pulse response Output 0 VCC = +/- 15 V -2 RL = 10 kΩ -4 Tamb = + 25 °C CL = 100 pF Overshoot 20 90% 16 12 8 VCC = +/- 15 V 4 0 RL = 10 kΩ 10% -6 0 2 4 6 8 Tamb = + 25 °C tr -4 0 10 0.2 0.6 0.4 0.8 1 12 14 Time (μs) Time (μs) Figure 16. Equivalent input noise voltage versus frequency Equivalent input noise voltage (nV/VHz) 100 90 80 70 60 50 40 30 VCC = +/- 15 V RS = 100 Ω Tamb = + 25 °C 20 10 0 10 40 100 400 1k 4k 10k 40k 100k Frequency (Hz) Parameter measurement information Figure 17. Voltage follower Figure 18. Gain of 10 inverting amplifier 10 kΩ 1 kΩ - eI 1/2 TL062 eI eo CL = 100 pF RL = 10 kΩ Doc ID 2294 Rev 4 - 1/2 TL062 eo RL CL = 100 pF 9/15 Typical applications 4 TL062, TL062A, TL062B Typical applications Figure 19. 100 kHz quadrature oscillator 1N 4148 18 pF 18 pF 18 k Ω (1) -15 V 1 kΩ - 1/2 88.4 k Ω - TL062 88.4 k Ω 1/2 TL062 6 sin ω t 6 cos ω t 1 kΩ 18 pF 88.4 k Ω 1N 4148 18 k Ω(1) +15 V 1. These resistor values may be adjusted for a symmetrical output. 10/15 Doc ID 2294 Rev 4 TL062, TL062A, TL062B 5 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Doc ID 2294 Rev 4 11/15 Package information 5.1 TL062, TL062A, TL062B DIP8 package information Figure 20. DIP8 package outline Table 5. DIP8 package mechanical data Dimensions Symbol Millimeters Min. Typ. A Min. Typ. Max. 0.210 A1 0.38 A2 2.92 3.30 4.95 0.115 0.130 0.195 b 0.36 0.46 0.56 0.014 0.018 0.022 b2 1.14 1.52 1.78 0.045 0.060 0.070 c 0.20 0.25 0.36 0.008 0.010 0.014 D 9.02 9.27 10.16 0.355 0.365 0.400 E 7.62 7.87 8.26 0.300 0.310 0.325 E1 6.10 6.35 7.11 0.240 0.250 0.280 0.015 e 2.54 0.100 eA 7.62 0.300 L 12/15 Max. 5.33 eB Note: Inches 10.92 2.92 3.30 3.81 0.430 0.115 0.130 0.150 Dimensions "D" and "E1" do not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.25 mm in total (both sides). Datum plane "H" coincides with the bottom of the lead, where the lead exits the body. Doc ID 2294 Rev 4 TL062, TL062A, TL062B 5.2 Package information SO-8 package information Figure 21. SO-8 package outline Table 6. SO-8 package mechanical data Dimensions Symbol Millimeters Min. Typ. A Inches Max. Min. Typ. 1.75 0.069 A1 0.10 A2 1.25 b 0.28 0.48 0.011 0.019 c 0.17 0.23 0.007 0.010 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 0.25 Max. 0.004 0.010 0.049 1.27 0.050 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 L1 k ccc 1.04 0 0.040 8° 0.10 Doc ID 2294 Rev 4 1° 8° 0.004 13/15 Ordering information 6 TL062, TL062A, TL062B Ordering information Table 7. Order codes Part number Temperature range Package Packaging Marking DIP8 Tube TL062IN TL062AIN TL062BIN TL062ID/IDT TL062AID/AIDT TL062BID/BIDT SO-8 Tube or tape and reel 062I 062AI 062BI TL062CN TL062ACN TL062BCN DIP8 Tube TL062CN TL062ACN TL062BCN SO-8 Tube or tape and reel 062C 062AC 062BC TL062IN TL062AIN TL062BIN -40 °C, +105 °C 0 °C, +70 °C TL062CD/CDT TL062ACD/ACDT TL062BCD/BCDT 7 Revision history Table 8. Document revision history Date Revision 28-Mar-2001 1 Initial release. 27-Jul-2007 2 Added values for Rthja and Rthjc in Table 1: Absolute maximum ratings. Added Table 2: Operating conditions. Updated format. 15-Mar-2010 3 Updated document format. Added TL062A and TL062B in title on cover page. Updated package information in Chapter 5. 4 Removed TL062M, AM, BM /TL062I, AI, BI / TL062C, AC, BC part numbers and temperature ranges from Table 1. and TL062M, AM, BM from Table 2. Removed TL062M, updated min. “Input common mode voltage range” for TL062C device in Table 3. Removed TL062AM and TL062BM devices, updated max. ”Input offset voltage - Tamb” for TL062AC, AI devices in Table 4. Removed TL062MN, TL062AMN, TL062BMN, TL062MD/MDT, TL062AMD/AMDT, TL062BMD/BMDT part numbers from Table 7. Minor corrections throughout document. 21-Sep-2012 14/15 Changes Doc ID 2294 Rev 4 TL062, TL062A, TL062B Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 2294 Rev 4 15/15