TL064MD

TL064 TL064A - TL064B LOW POWER J-FET QUAD OPERATIONAL AMPLIFIERS s s s s s s s s VERY LOW POWER CONSUMPTION : 200µA WIDE COMMON-MODE (UP TO VCC+) AND DIFFERENTIAL VOLTAGE RANGES LOW INPUT BIAS AND OFFSET CURRENTS OUTPUT SHORT-CIRCUIT PROTECTION HIGH INPUT IMPEDANCE J-FET INPUT STAGE INTERNAL FREQUENCY COMPENSATION LATCH UP FREE OPERATION HIGH SLEW RATE : 3.5V/µs N DIP14 (Plastic Package) D SO14 (Plastic Micropackage) DESCRIPTION The TL064, TL064A and TL064B are high speed J-FET input quad operational amplifiers. Each of these J-FET input operational amplifiers incorporates well matched, high voltage J-FET and bipolar transistors in a monolithic integrated circuit. The device features high slew rate, low input bias and offsetcurrents, andlow offset voltage temperature coefficient. PIN CONNECTIONS (top view) ORDER CODES Part Number TL064M/AM/BM TL064I/AI/BI TL064C/AC/BC Example : TL064IN Temperature Range -55 C, +125 C -40 C, +105 C 0oC, +70oC o o o o Package N • • • D • • • Output 1 1 Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7 + + + + 14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3 October 1997 1/10 TL064 - TL064A - TL064B SCHEMATIC DIAGRAM V CC 220Ω Inverting Input Non-inverting Input 45k Ω 64Ω Output 1/4 TL064 270Ω 3.2k Ω 4.2k Ω 100Ω V CC MAXIMUM RATINGS Symbol VCC Vi Vid Ptot Toper Tstg Parameter Supply Voltage - (note 1) Input Voltage - (note 3) Differential Input Voltage - (note 2) Power Dissipation Output Short-Circuit Duration (Note 4) Operating Free-Air Temperature Range Storage Temperature Range TL064M,AM,BM ±18 ±15 ±30 680 Infinite -55 to +125 -65 to +150 TL064I,AI,BI ±18 ±15 ±30 680 Infinite -40 to +105 -65 to +150 TL064C,AC,BC ±18 ±15 ±30 680 Infinite 0 to +70 -65 to +150 o Unit V V V mW C C o N otes : 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC+ and VCC-. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded. 2/10 TL064 - TL064A - TL064B ELECTRICAL CHARACTERISTICS VCC = ± 15V, Tamb = 25oC (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage (Rs = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Temperature Coefficient of Input Offset Voltage (Rs = 50Ω) Input Offset Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. Input Bias Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. Input Common Mode Voltage Range Output Voltage Swing (RL = 10kΩ) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Large Signal Voltage Gain (RL = 10kΩ, Vo = ± 10V) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Gain Bandwidth Product o (Tamb = 25 C, RL = 10kΩ CL = 100pF) Input Resistance Common Mode Rejection Ratio (Rs = 50Ω) Supply Voltage Rejection Ratio (Rs = 50Ω) Supply Current (Per Amplifier) (Tamb = 25oC, no load, no signal) Channel Separation o (Av = 100, Tamb = 25 C) Total Power Consumption o (Tamb = 25 C, no load, no signal) 80 80 ± 11.5 TL064M Min. Typ. Max. 3 6 15 Min. TL064I Typ. Max. Min. 3 6 9 TL064C Typ. Max. 3 15 20 µV/ C o Unit mV DVio Iio 10 5 100 20 200 50 ±11.5 10 5 100 10 200 20 ±11 10 5 200 5 400 10 pA nA pA nA V Iib 30 30 30 Vicm +15 -12 27 +15 -12 27 +15 -12 V 27 V/mV VOPP 20 20 20 20 20 20 Avd 4 4 6 4 4 6 3 3 6 MHz GBP 1 10 12 1 10 80 80 250 12 1 10 70 70 250 12 Ri CMR SVR Icc VO1/VO2 PD Ω dB 86 95 200 120 6 7.5 86 95 200 120 6 7.5 76 dB 95 200 120 mW 6 7.5 250 µA dB * The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. ELECTRICAL CHARACTERISTICS (continued) VCC = ± 15V, Tamb = 25oC Symbol SR tr KOV en Parameter Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1) Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) (see Figure 1) Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) (see figure 1) Equivalent Input Noise Voltage (Rs = 100Ω, f = 1KHz) TL064C,I,M Min. 1.5 Typ. 3.5 0.2 10 42 nV  Hz √ Max. Unit V/µs µs % 3/10 TL064 - TL064A - TL064B ELECTRICAL CHARACTERISTICS (continued) VCC = ± 15V, Tamb = 25oC (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage (Rs = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Temperature Coefficient of Input Offset Voltage (Rs = 50Ω) Input Offset Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. Input Bias Current * Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. Input Common Mode Voltage Range Output Voltage Swing (RL = 10kΩ) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Large Signal Voltage Gain (RL = 10kΩ, Vo = ± 10V) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Gain Bandwidth Product o (Tamb = 25 C, RL = 10kΩ, CL = 100pF) Input Resistance Common Mode Rejection Ratio (R s = 50Ω) 80 SVR Icc VO1/VO2 PD SR tr KOV en Supply Voltage Rejection Ratio (Rs = 50Ω) Supply Current (Per Amplifier) (Tamb = 25oC, no load, no signal) Channel Separation (Av = 100, Tamb = 25oC) Total Power Consumption (Each Amplifier) o (Tamb = 25 C, no load, no signal) Slew Rate (Vi = 10V, RL = 10kΩ, CL = 100pF, AV = 1) Rise Time (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) Overshoot Factor (Vi = 20mV, RL = 10kΩ, CL = 100pF, AV = 1) - (see figure 1) Equivalent Input Noise Voltage (Rs = 100Ω, f = 1KHz) 1.5 80 86 95 200 120 6 3.5 0.2 10 42 7.5 1.5 250 80 80 86 dB 95 200 120 mW 6 3.5 0.2 10 42 nV  Hz √ 7.5 V/µs µs % 250 µA dB ± 11.5 TL064AC,AI,AM Min. Typ. Max. 3 6 7.5 TL064BC,BI,BM Min. Typ. Max. 2 3 5 µV/ C o Unit mV DVio Iio 10 5 100 3 200 7 ±11.5 10 5 100 3 200 7 pA nA pA nA V V Iib 30 +15 -12 27 30 +15 -12 27 Vicm VOPP 20 20 4 4 20 20 4 4 Avd V/mV 6 6 MHz 1 1012 1 1012 Ω dB GBP Ri CMR * The input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques must be used that will maintain the junction temperature as close to the ambient temperature as possible. 4/10 TL064 - TL064A - TL064B MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS SUPPLY VOLTAGE 30 25 20 15 10 5 T a m b= +25°C See fig ure 2 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREE AIR TEMP. MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) R L = 1 0 kΩ 30 25 20 15 10 5 0 -7 5 -5 0 - 25 0 25 50 75 -50 125 F R EE A I R T EM P E R AT U R E ( ° C ) VC C = R L 15V = 10k Ω See Figure 2 0 2 4 6 8 10 12 14 16 SUPPLY VOLTAGE (V) MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS LOAD RESISTANCE MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY 30 25 VOLTAGE (V) MAXIMUM PEAK-TO-PEAK OUTPUT 30 25 VOLTAGE (V) VCC = 15V VC C = 12V R L = 10kΩ Tamb = +25°C See Figure 2 20 15 10 20 15 10 5 0 100 200 700 1k 2k Tamb = +25°C See Figure 2 400 VCC = 15V VCC = VCC = 5V 2V 5 0 1k 4k 7k 10k 10K 100K 1M 10M LOAD RESISTANCE (kΩ) FREQUENCY (Hz) DIFFERENTIAL VOLTAGE AMPLIFICATION VERSUS FREE AIR TEMPERATURE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT VERSUS FREQUENCY 6 10 DIFFERENTIAL VOLTAGE DIFFERENTIAL VOLTAGE 10 AMPLIFICATION (V/V) 7 AMPLIFICATION (V/mV) 105 4 10 10 VCC = 5V to 15V RL = 2kΩ Tamb = +25°C DIFFER ENTIAL VOLTAGE AMPLIFICATION (left scale) PHASE SHIFT (right scale) 0 4 3 45 90 135 2 102 101 VCC = 15V R L = 10kΩ -75 1 -50 -25 0 25 50 75 100 FREE AIR TEMPERATURE (°C) 125 1 10 100 1k 10k 100k 1M 180 10M FREQUENCY (Hz) 5/10 TL064 - TL064A - TL064B SUPPLY CURRENT PER AMPLIFIER VERSUS SUPPLY VOLTAGE 250 SUPPLY CURRENT (µA) SUPPLY CURRENT PER AMPLIFIER VERSUS FREE AIR TEMPERATURE 250 SUPPLY CURRENT (µA) 200 150 100 200 150 100 50 0 T amb = +25°C No signal No load 50 0 VCC = 15V No signal No load 0 2 4 10 12 6 8 SUPPLY VOLTAGE ( V) 14 16 -75 -50 -25 0 25 50 75 100 125 FREE AIR TEMPERATURE ( °C) TOTAL POWER DISSIPATED VERSUS FREE AIR TEMPERATURE 30 25 COMMON MODE REJECTION RATIO (dB) TOTAL POWER DISSIPATED (mW) COMMON MODE REJECTION RATIO VERSUS FREE AIR TEMPERATURE 87 86 85 84 83 82 81 -75 20 15 10 VCC = 15V No signal No load 5 0 VC C = R L 1 5V = 1 0kΩ -75 -50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125 FREE AIR TEMPERATURE (°C) FREE AIR TEMPERATURE (°C) NORMALIZED UNITY GAIN BANDWIDTH SLEW RATE, AND PHASE SHIFT VERSUS TEMPERATURE INPUT BIAS CURRENT VERSUS FREE AIR TEMPERATURE 100 NORMALIZED UNITY-GAIN BANDWIDTH AND SLEW RATE UNITY -GAIN-BANDWIDTH (left scale) PHASE SHIFT (right scale) INPUT BIAS CURRENT (nA) 1.3 1.2 1.1 1.03 1.02 1.01 VCC = 15V 10 1 NORMALIZED PHASESHIFT 1 0.9 0.8 0.7 -75 S LEW RAT E (left scale) 1 0.99 0.98 R L = 10kΩ f = B1for phase shift -50 -25 VCC = 15V 0.1 0 25 50 0.97 75 100 125 FREE AIR TEMPERATURE (°C) 0.01 -50 -25 0 25 50 75 100 125 FREE AIR TEMPERATURE (°C) 6/10 TL064 - TL064A - TL064B VOLTAGE FOLLOWER LARGE SIGNAL RESPONSE INPUT AND OUTPUT VOLTAGES OUTPUT VOLTAGE VERSUS ELAPSED TIME 28 24 OUTPUT VOLTAGE (mV) OVERSHOOT 6 4 INPUT 2 (V) 20 16 12 8 4 10% OUTPUT 90% 0 -2 -4 VCC = 15V R L = 10kΩ CL = 100pF Tamb = +25°C V CC = 15V 0 t -4 0 0.2 r R L = 10k Ω Tamb = +25°C 0.4 0.6 0.8 1 12 14 -6 0 2 4 6 TIME (µs) 8 10 TIME ( µs) EQUIVALENT INPUT NOISE VOLTAGE VERSUS FREQUENCY 100 90 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 80 70 60 50 40 30 20 10 0 40 10 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) 15V VC C = R S = 100Ω T a m b = +25 ° C 7/10 TL064 - TL064A - TL064B PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage follower Figure 2 : Gain-of-10 inverting amplifier 10k Ω 1k Ω 1k Ω 10k Ω eI 1/4 eI 1/4 TL064 RL eo TL064 RL eo CL = 100pF CL = 100pF TYPICAL APPLICATION AUDIO DISTRIBUTION AMPLIFIER fO = 1 00 kHz 1/ 4 1M Ω TL0 64 Output A 1 µF Input 100k 1/ 4 TL064 1 /4 TL064 Output B Ω 100k Ω 100k Ω V CC+ - 1OO µF 100k Ω 1/ 4 TL0 64 Output C 8/10 TL064 - TL064A - TL064B PACKAGE MECHANICAL 14 PINS - PLASTIC DIP Dimensions a1 B b b1 D E e e3 F i L Z Min. 0.51 1.39 Millimeters Typ. Max. 1.65 Min. 0.020 0.055 Inches Typ. Max. 0.065 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100 DIP14.TBL 9/10 PM-DIP14.EPS TL064 - TL064A - TL064B PACKAGE MECHANICAL 14 PINS - PLASTIC MICROPACKAGE (SO) Dimensions A a1 a2 b b1 C c1 D E e e3 F G L M S Min. 0.1 0.35 0.19 Millimeters Typ. Max. 1.75 0.2 1.6 0.46 0.25 45 (typ.) o Min. 0.004 0.014 0.007 Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.5 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8 (max.) o 0.020 8.75 6.2 0.336 0.228 0.050 0.300 0.150 0.181 0.020 0.157 0.208 0.050 0.027 0.334 0.244 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specification mentioned in this pub lication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. ORDER CODE : © 1997 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved SGS-THOM SON Microelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. 10/10 SO14.TBL PM-SO14.EPS