®
TL071 TL071A - TL071B
LOW NOISE J-FET SINGLE OPERATIONAL AMPLIFIERS
. . . . . . . . .
WIDE COMMON-MODE (UP TO VCC+) AND DIFFERENTIAL VOLTAGE RANGE LOW INPUT BIAS AND OFFSET CURRENT LOW NOISE en = 15nV/√Hz (typ) OUTPUT SHORT-CIRCUIT PROTECTION HIGH INPUT IMPEDANCE J–FET INPUT STAGE LOW HARMONIC DISTORTION : 0.01% (typ) INTERNAL FREQUENCY COMPENSATION LATCH UP FREE OPERATION HIGH SLEW RATE : 16V/µs (typ)
N DIP8 (Plastic Package)
D SO8 (Plastic Micropackage)
DESCRIPTION The TL071, TL071A and TL071B are high speed J–FET inputsingle operationalamplifiers incorporating well matched, high voltage J–FET and bipolar transistors in a monolithic integrated circuit. The devicesfeaturehigh slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. PIN CONNECTIONS (top view)
ORDER CODES
Part Number TL071M/AM/BM TL071I/AI/BI TL071C/AC/BC Example : TL071CN Temperature Range –55 C, +125 C –40 C, +105 C 0 C, +70 C
o o o o o o
Package N • • • D • • •
1 2 3 4
8 7 6 5
1 2 3 4 5 6 7 8
- Offset Null 1 - Inverting input - Non-inverting input - VCC - Offset Null 2 - Output + - VCC - N.C.
December 1998
1/9
TL071 - TL071A - TL071B
SCHEMATIC DIAGRAM
V
CC
Non-inverting input Inver ting input
100 Ω
200 Ω Output
100 Ω 30k
8.2k
1.3k
35k
1.3k
3 5k
100 Ω
V CC
Offset Null1
Offset Null2
INPUT OFFSET VOLTAGE NULL CIRCUITS
TL071
N1
N2 100k Ω V CC
ABSOLUTE MAXIMUM RATINGS
Symbol VCC Vi Vid Ptot Toper Supply Voltage - (note 1) Input Voltage - (note 3) Differential Input Voltage - (note 2) Power Dissipation Output Short-circuit Duration - (note 4) Operating Free Air Temperature Range TL071C,AC,BC TL071I,AI,BI TL071M,AM,BM Parameter Value ±18 ±15 ±30 680 Infinite 0 to 70 –40 to 105 –55 to 125 –65 to 150
o
Unit V V V mW C
Tstg
Notes :
Storage Temperature Range
o
C
1. All voltage values, except differential voltage, are+with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC and VCC–. 2. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the dissipation rating is not exceeded.
2/9
TL071 - TL071A - TL071B
ELECTRICAL CHARACTERISTICS VCC = ±15V, Tamb = 25oC (unless otherwise specified)
Symbol Vio Parameter Input Offset Voltage (R S = 50Ω) o TL071 Tamb = 25 C TL071A TL071B TL071 Tmin. ≤ Tamb ≤ Tmax. TL071A TL071B Input Offset Voltage Drift Input Offset Current * o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Input Bias Current * o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Large Signal Voltage Gain (RL = 2kΩ, VO = ±10V) Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. Supply Voltage Rejection Ratio (R S = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Supply Current, no Load Tamb = 25oC Tmin. ≤ Tamb ≤ Tmax. Input Common Mode Voltage Range Common Mode Rejection Ratio (RS = 50Ω) o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Output Short-circuit Current o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. Output Voltage Swing o Tamb = 25 C Tmin. ≤ Tamb ≤ Tmax. SR tr KOV GBP Ri THD en ∅m RL RL RL RL = = = = 2k Ω 10kΩ 2k Ω 10kΩ ± 11 50 25 80 80 TL071I,M,AC,AI, AM,BC,BI,BM Min. Typ. 3 3 1 Max. 10 6 3 13 7 5 Min. TL071C Typ. 3 Max. mV 10 13 µV/ C 100 10 200 20 pA nA pA nA V/mV 200 25 15 70 70 2.5 2.5 ±11 200 dB 86 86 mA 1.4 +15 -12 86 1.4 +15 -12 86 mA 10 10 10 12 10 12 8 40 60 60 10 10 10 12 10 12 8 40 60 60 V 12 13.5 12 13.5 V/µs µs % 10 2.5 4 10
12 o
Unit
DV io Iio
10 5 100 4 200 20
10 5
Iib
20
20
Avd
SVR
ICC
2.5 2.5 V dB
Vicm CMR
80 80
70 70
Ios ±VOPP
Slew Rate (Vin = 10V, RL = 2kΩ, CL = 100pF, o Tamb = 25 C, unity gain) Rise Time (Vin = 20mV, RL = 2kΩ, C L = 100pF, Tamb = 25oC, unity gain) Overshoot (Vin = 20mV, RL = 2kΩ, C L = 100pF, o Tamb = 25 C, unity gain) Gain Bandwidth Product (f = 100kHz, Tamb = 25oC, Vin = 10mV, R L = 2kΩ, C L = 100pF) Input Resistance Total Harmonic Distortion (f = 1kHz, AV = 20dB, RL = 2kΩ, C L = 100pF, Tamb = 25oC, VO = 2VPP) Equivalent Input Noise Voltage (f = 1kHz, Rs = 100Ω) Phase Margin
16 0.1
16 0.1 10
MHz 2.5 4 10
12
Ω %
0.01 15 45
0.01 15 45 nV Hz √ Degrees
* The input bias currents are junction leakage currents which approximately double for every 10oC increase in the junction temperature.
3/9
TL071 - TL071A - TL071B
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY
30 MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V) V CC = 25 20 V CC = 15 10 5 0 100 10V 15V
R L = 2 kΩ T a m b = +25 ° C S ee Figure 2
MAXIMUMPEAK-TO-PEAK OUTPUT VOLTAGE (V)
30 25 20 15 10 5 0 100 1K 10K 100K
V CC =
5V
V CC = 15V V CC = 10V
R L= 10kΩ Ta mb = +25 C S e e Figure 2
V CC =
5V
1K
10K
100K
1M
10M
1M
10M
FREQUENCY (Hz)
FREQUENC Y (Hz)
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY
MAXIMUMPEAK-TO-PEAK OUTPUT VOLTAGE (V)
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREE AIR TEMP.
30
Tamb = +25 C
25 20 15
VCC =
15V
R L = 2kΩ S ee Figure 2
MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V)
30 25 20
R L = 1 0 kΩ
15 10 5 0 - 75 - 50 - 25 0 25 50 75 - 50 1 25 T E MP ER AT U R E ( ° C )
Ta mb = -55 C
10 5 0
R L = 2 kΩ
VC C =
15V
Ta mb = +125 C 10k 40k 100k 400k 1M 4M 10M
Se e F i gu re 2
FREQUENCY (Hz)
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS LOAD RESISTANCE
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS SUPPLY VOLTAGE
MAXIMUM PEAK-TO-PEAK OUTPUT
25
VOLTAGE (V)
VCC = 15V Tamb = +25°C
See Figure 2
MAXIMUM PEAK-TO-PEAKOUTPUT VOLTAGE (V)
30
30 25
RL = 10 kΩ Tamb = +25°C
20
15 10
20
15 10
5
0
0.1 0.2 0.4 0.7 1 2 4 7 10
5
0 2
4 6 8 10 12 SUPPLY VOLTAGE ( V)
14
16
LOAD RESISTANCE (k Ω )
4/9
TL071 - TL071A - TL071B
INPUT BIAS CURRENT VERSUS FREE AIR TEMPERATURE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION VERSUS FREE AIR TEMPERATURE
100 V CC = INPUT BIAS CURRENT (nA) 10 15V
DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V)
1000 400 200 100 40 20 10 4 2 1 -75 V CC = VO = R
L
1
15V 10V
0.1
= 2k Ω
0.01 -50
-25
0
25
50
75
100
125
-50
-25
0
25
50
75
100
125
TEMPERATURE (°C)
TEMPERATURE (°C)
LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT VERSUS FREQUENCY
TOTAL POWER DISSIPATION VERSUS FREE AIR TEMPERATURE
250
DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V)
100
P HASE SHIFT (right sca le)
DIFFERENTIAL VOLTAGE AMPLIFICATION (le fts ca le)
180
TOTAL POWER DISSIPATION (mW)
225 200 175 150 125 100 75 50 25 0 -75 -50 -25 0 25 50
V CC = No signal No load
15V
10
1 100
R L = 2kΩ C L = 100pF V CC = 15V T a mb = +125 C
1K 10K 100K 1M 10M FREQUENCY (Hz)
90
0
75
100
125
TEMPERATURE (°C)
SUPPLY CURRENT PER AMPLIFIER VERSUS FREE AIR TEMPERATURE
2.0
COMMON MODE REJECTION RATIO VERSUS FREE AIR TEMPERATURE
89 COMMON MODE MODE REJECTION RATIO (dB)
1.8 SUPPLY CURRENT (mA) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -75 -50 -25 0 25 50
V CC = No signal No load
15V
88 87 86 85 84 83 -75
R L = 1 0 kΩ VC C = 15V
-50
-25
0
25
50
75
100
125
75
100
125
TEMPERATURE (°C)
TEMPERATURE (°C)
5/9
TL071 - TL071A - TL071B
VOLTAGE FOLLOWER LARGE SIGNAL PULSE RESPONSE OUTPUT VOLTAGE VERSUS ELAPSED TIME
INPUT AND OUTPUT VOLTAGES (V)
6
OUTPUT VOLTAGE (mV)
28 24
4 2 0 -2 -4 -6 0
OUTPUT INPUT
OVERSHOOT
20 16 12 8 4
10%
90%
VCC = 15V R L = 2 kΩ C L= 100pF Ta mb = +25 C
V
R L = 2k Ω t
r
CC
= 15V
0 -4 0 0.1 0.2 0.3 0.4
Tamb = +25°C 0.5 0.6 0.7
0.5
1
1.5
2
2.5
3
3.5
TIME (µs)
TIME ( µs)
EQUIVALENT INPUT NOISE VOLTAGE VERSUS FREQUENCY
TOTAL HARMONIC DISTORTION VERSUS FREQUENCY
70
1 TOTAL HARMONIC DISTORTION (%)
VCC = A V = 10 R S = 100 Ω T amb = +25°C 15V
60 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 50 40 30 20 10 0 10 40 100 400 1k
0.4 0.1 0.04 0.01 0.004 0.001 100
V V = = 15V 15V CC
CC
1 A A V= = 1 V V V (rms) = = 6V 6V O
O (rms)
T amb = = +25 °C T amb +25 °C
4k
10k
40k 100k
400
1k
4k
10k
40k
100k
FREQUENCY (Hz)
FREQUENCY (Hz)
6/9
TL071 - TL071A - TL071B
PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier
10k Ω
eI
TL071
1k Ω
TL071
CL = 100pF
RL = 2kΩ
eo
eo
RL
eI
CL = 100pF
TYPICAL APPLICATIONS (0.5Hz) SQUARE WAVE OSCILLATOR
R F = 1 0 0k
Ω
3.3 k
Ω
-
+15V
T L0 71
1k Ω
C = 3.3
F
µF
-15V
3.3k
Ω
9.1k
Ω
f osc=
1 2 xR
F
CF
HIGH Q NOTCH FILTER
TL 0 7 1
R1
R2
fo=
1 2 xR
F
= 1kHz CF
C3 C3 2
R3
C1 = C2 =
= 100pF
R1 = R2 = 2R3 = 1.5M C1 C2
Ω
7/9
TL071 - TL071A - TL071B
P ACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP
Dimensions A a1 B b b1 D E e e3 e4 F i L Z
Min. 0.51 1.15 0.356 0.204 7.95
Millimeters Typ. 3.32
Max.
Min. 0.020 0.045 0.014 0.008 0.313
Inches Typ. 0.131
Max.
1.65 0.55 0.304 10.92 9.75 2.54 7.62 7.62 6.6 5.08 3.81 1.52
0.065 0.022 0.012 0.430 0.384 0.100 0.300 0.300 0260 0.200 0.150 0.060
3.18
0.125
8/9
TL071 - TL071A - TL071B
P ACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO)
Dimensions A a1 a2 a3 b b1 C c1 D E e e3 F L M S
Min. 0.1 0.65 0.35 0.19 0.25 4.8 5.8
Millimeters Typ.
Max. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45 (typ.) 5.0 6.2
o
Min. 0.004 0.026 0.014 0.007 0.010 0.189 0.228
Inches Typ.
Max. 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.197 0.244
1.27 3.81 3.8 0.4 4.0 1.27 0.6 8 o (max.) 0.150 0.016
0.050 0.150 0.157 0.050 0.024
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this pub lication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST log o is a trademark of STMicroelectronics © 1998 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. © http://www.st.com
9/9