TL084M

TL084 TL084A - TL084B GENERAL PURPOSE J-FET QUAD OPERATIONAL AMPLIFIERS s WIDE COMMON-MODE (UP TO VCC+) AND DIFFERENTIAL VOLTAGE RANGE s LOW INPUT BIAS AND OFFSET CURRENT s OUTPUT SHORT-CIRCUIT PROTECTION s HIGH INPUT IMPEDANCE J–FET INPUT STAGE N DIP14 (Plastic Package) s INTERNAL FREQUENCY COMPENSATION s LATCH UP FREE OPERATION s HIGH SLEW RATE : 16V/µs (typ) D SO14 (Plastic Micropackage) p TSSOP14 (Thin Shrink Small Outline Package) ORDER CODE DESCRIPTION Part Number Temperature Range Package N • • • D • • • P • • • The TL084, TL084A and TL084B are high speed J–FET input quad operational amplifiers incorporating well matched, high voltage J–FET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. PIN CONNECTIONS (top view) TL084M/AM/BM -55°C, +125°C TL084I/AI/BI -40°C, +105°C TL084C/AC/BC 0°C, +70°C Example : TL084CN, TL084CD N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = T hin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT) Output 1 1 Inverting Input 1 2 Non-inverting Input 1 3 VCC + 4 Non-inverting Input 2 5 Inverting Input 2 6 Output 2 7 + + + + 14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3 March 2001 1/12 TL084 - TL084A - TL084B SCHEMATIC DIAGRAM (each amplifier) VCC Non-inverting input Inverting input 1 0 0Ω 2 0 0Ω Output 1 0 0Ω 30k 8.2k 1.3k VCC 35k 1.3k 35k 1 0 0Ω ABSOLUTE MAXIMUM RATINGS Symbol VCC Vi Vid Ptot Toper Tstg 1. 2. 3. 4. Parameter Supply voltage - note 1) Input Voltage - note Power Dissipation Output Short-circuit Duration - note 4) Operating Free-air Temperature Range Storage Temperature Range 2) 3) TL084M, AM, BM TL084I, AI, BI TL084C, AC, BC Unit V V V mW ±18 ±15 ±30 680 Infinite -55 to +125 -40 to +105 -65 to +150 0 to +70 Differential Input Voltage - note °C °C All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between VCC + and VCC -. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating is not exceeded 2/12 TL084 - TL084A - TL084B ELECTRICAL CHARACTERISTICS VCC = ±15V, Tamb = +25°C (unless otherwise specified) Symbol Parameter Input Offset Voltage (Rs = 50Ω) Tamb = +25°C Vio Tmin ≤ Tamb ≤ Tmax TL084I,M,AC,AI,AM, BC,BI,BM Min. TL084 TL084A TL084B TL084 TL084A TL084B Typ. 3 3 1 Max. 10 6 3 13 7 5 Min. TL084C Unit Typ. 3 Max. mV 10 13 DVio Iio Input Offset Voltage Drift Input Offset Current - note Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Bias Current -note 1 Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Large Signal Voltage Gain (RL = 2kΩ, Vo = ±10V) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Supply Voltage Rejection Ratio (RS = 50Ω) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Supply Current, no load, per amplifier Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Input Common Mode Voltage Range Common Mode Rejection Ratio (RS = 50Ω) Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Output Short-circuit Current Tamb = +25°C Tmin ≤ Tamb ≤ Tmax Output Voltage Swing Tamb = +25°C RL = 2kΩ RL = 10kΩ RL = 2kΩ RL = 10kΩ ±11 50 25 80 80 1) 10 5 100 4 200 20 25 15 70 70 2.5 2.5 ±11 10 5 100 4 400 20 µV/°C pA nA pA nA V/mV Iib 20 20 Avd 200 200 dB SVR 86 86 mA ICC Vicm CMR 1.4 +15 -12 86 1.4 +15 -12 86 2.5 2.5 V dB 80 80 10 10 10 12 10 12 8 70 70 60 60 10 10 10 12 10 12 8 mA 40 40 60 60 V 12 13.5 12 13.5 Ios ±Vopp Tmin ≤ Tamb ≤ Tmax SR tr Kov GBP Ri Slew Rate (Tamb = +25°C) Vin = 10V, RL = 2kΩ, CL = 100pF, unity gain Rise Time (Tamb = +25°C) Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain Overshoot (Tamb = +25°C) Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain Gain Bandwidth Product (Tamb = +25°C) Vin = 10mV, RL = 2kΩ, CL = 100pF, f= 100kHz Input Resistance V/µs 16 0.1 10 2.5 4 1012 2.5 16 µs 0.1 % 10 MHz 4 1012 Ω 3/12 TL084 - TL084A - TL084B Symbol Parameter Total Harmonic Distortion (Tamb = +25°C), f= 1kHz, RL = 2kΩ,CL = 100pF, Av = 20dB, Vo = 2Vpp Equivalent Input Noise Voltage RS = 100Ω, f = 1KHz TL084I,M,AC,AI,AM, BC,BI,BM Min. Typ. Max. Min. TL084C Unit Typ. Max. % THD 0.01 0.01 nV ----------Hz degrees en ∅m 15 45 120 15 45 120 Phase Margin Channel Separation Vo1/Vo2 Av = 100 1. dB The input bias currents are junction leakage currents which approximately double for every 10°C increase in the junction temperature. 4/12 TL084 - TL084A - TL084B MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREQUENCY MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREQUENCY MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREQUENCY MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus FREE AIR TEMP. MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus LOAD RESISTANCE MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE versus SUPPLY VOLTAGE MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) 30 25 RL = 10 kΩ Tamb = +25˚C 20 15 10 5 0 2 4 6 8 10 12 SUPPLY VOLTAGE ( V) 14 16 5/12 TL084 - TL084A - TL084B INPUT BIAS CURRENT versus FREE AIR TEMPERATURE LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION versus FREE AIR TEMP. 100 V CC = INPUT BIAS CURRENT (nA) 10 1 0.1 15V DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V) 1000 400 200 100 40 20 10 4 2 1 -75 V CC = 15V V O = 10V R L = 2k Ω -50 0.01 -50 -25 0 25 50 75 100 125 -25 0 25 50 75 100 125 TEMPERATURE (˚C) TEMPERATURE (˚C) LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT versus FREQUENCY TOTAL POWER DISSIPATION versus FREE AIR TEMPERATURE PHASE SHIFT (right scale) DIFFERENTIAL VOLTAGE AMPLIFICATION (left scale) 180 10 1 100 R = 2kW L C L = 100pF V CC = 15V T amb = +125°C 1K 10K 100K 1M 10M FREQUENCY (Hz) 90 0 TOTAL POWER DISSIPATION (mW) 100 250 225 200 175 150 125 100 75 50 25 0 -75 -50 -25 0 25 50 TEMPERATURE (˚C) DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V) V CC = 15V No signal No load 75 100 125 SUPPLY CURRENT PER AMPLIFIER versus FREE AIR TEMPERATURE SUPPLY CURRENT PER AMPLIFIER versus SUPPLY VOLTAGE 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 -75 -50 -25 0 25 50 TEMPERATURE (˚C) SUPPLY CURRENT (mA) V CC = 15V No signal No load 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 SUPPLY CURRENT (mA) Tamb = +25˚C No signal No load 75 100 125 2 4 6 10 12 8 SUPPLY VOLTAGE ( V) 14 16 6/12 TL084 - TL084A - TL084B COMMON MODE REJECTION RATIO versus FREE AIR TEMPERATURE VOLTAGE FOLLOWER LARGE SIGNAL PULSE RESPONSE INPUT AND OUTPUT VOLTAGES (V) 89 COMMON MODE MODE REJECTION RATIO (dB) 88 87 86 85 84 83 -75 -50 -25 0 25 50 75 100 125 R L = 10 kΩ VC C = 15V 6 4 2 0 -2 -4 -6 0 VCC= 15V R L = 2 kW OUTPUT INPUT C L= 100pF Tamb = +25°C 0.5 1 1.5 2 2.5 3 3.5 TEMPERATURE (˚C) TIME (m s) OUTPUT VOLTAGE versus ELAPSED TIME EQUIVALENT INPUT NOISE VOLTAGE versus FREQUENCY 28 24 OUTPUT VOLTAGE (mV) OVERSHOOT 90% 70 60 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 50 40 30 20 10 0 10 40 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) VCC = 15V A V = 10 R S = 100 Ω T amb = +25˚C 20 16 12 8 4 10% V 0 -4 0 tr 0.1 0.2 0.3 0.4 TIME ( µs) R L = 2k Ω Tamb = +25˚C 0.5 0.6 0.7 CC = 15V TOTAL HARMONIC DISTORTION versus FREQUENCY 1 TOTAL HARMONIC DISTORTION (%) 0.4 0.1 0.04 0.01 0.004 0.001 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) V V = = 15V 15V CC CC 1 A A V= = 1 V V V O (rms) = 6V O (rms) = 6V T amb = = +25˚C T amb +25˚C 7/12 TL084 - TL084A - TL084B PARAMETER MEASUREMENT INFORMATION Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier 10k Ω 1k Ω eI - 1/4 TL084 eo RL CL = 100pF TYPICAL APPLICATIONS AUDIO DISTRIBUTION AMPLIFIER fO = 100kHz 1M Ω 1/4 TL084 Output A 1 µF Input 100k Ω 100k Ω 100k Ω 100k Ω 1/4 TL084 - 1/4 TL084 Output B 1OO µF V CC+ 1/4 TL084 Output C 8/12 TL084 - TL084A - TL084B TYPICAL APPLICATIONS (continued) POSITIVE FEEDBACK BANDPASS FILTER 16k Ω 22 0p F 43k Ω Input 43k Ω 22 0p F 1/4 TL 08 4 43k Ω 1/4 TL 08 4 30k Ω 43k Ω 22 0p F 1/4 TL 08 4 220 pF 43k Ω 16k Ω 30k Ω 43k Ω 1/4 TL 08 4 1.5 k Ω 1.5 k Ω Output B Ground Output A OUTPUT A OUTPUT B SECOND ORDER BANDPASS FILTER fo = 100kHz; Q = 30; Gain = 4 CASCADED BANDPASS FILTER fo = 100kHz; Q = 69; Gain = 16 9/12 TL084 - TL084A - TL084B PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Millimeters Dim. Min. a1 B b b1 D E e e3 F i L Z 0.51 1.39 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 Typ. Max. 1.65 Min. 0.020 0.055 Inches Typ. Max. 0.065 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100 10/12 TL084 - TL084A - TL084B PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO) L C G c1 a2 b e3 D M e A s E 14 1 8 7 F Millimeters Dim. Min. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S 0.1 0.35 0.19 0.5 45° (typ.) 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8° (max.) 0.150 0.181 0.020 8.75 6.2 0.336 0.228 Typ. Max. 1.75 0.2 1.6 0.46 0.25 Min. 0.004 0.014 0.007 a1 Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.020 0.344 0.244 0.050 0.300 0.157 0.208 0.050 0.027 Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK. b1 11/12 TL084 - TL084A - TL084B PACKAGE MECHANICAL DATA 14 PINS - THIN SHRINK SMALL OUTLINE PACKAGE c k 0,25 mm .010 inch GAGE PLANE L E1 SEATING PLANE C A A2 A1 b e E 8 7 D aaa C 14 1 PIN 1 IDENTIFICATION Millimeters Dim. Min. A A1 A2 b c D E E1 e k l 0.05 0.80 0.19 0.09 4.90 4.30 0° 0.50 Typ. Max. 1.20 0.15 1.05 0.30 0.20 5.10 4.50 8° 0.75 Min. 0.01 0.031 0.007 0.003 0.192 0.169 0° 0.09 L1 Inches Typ. Max. 0.05 0.006 0.041 0.15 0.012 0.20 0.177 8° 0.030 1.00 0.039 5.00 6.40 4.40 0.65 0.60 0.196 0.252 0.173 0.025 0.0236 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 12/12