TMMBAT42FILM

TMMBAT42 - TMMBAT43 Small signal Schottky diodes Datasheet - production data Description General purpose metal to silicon diode featuring very low turn-on voltage and fast switching. These devices have integrated protection against excessive voltage such as electrostatic discharges. 0,1,0(/) Features • Very small conduction losses • Negligible switching losses • Low forward voltage drop July 2015 This is information on a product in full production. DocID3497 Rev 3 1/7 www.st.com Characteristics 1 TMMBAT42 - TMMBAT43 Characteristics Table 1. Absolute maximum ratings at 25 °C unless otherwise specified Symbol VRRM IF Parameter Repetitive peak reverse voltage Value Unit 30 V Forward continuous current Tl = 25 °C 200 mA IFRM Repetitive peak forward current tp ≤ 1 s δ ≤ 0.5 500 mA IFSM Surge non repetitive forward current tp = 10 ms 4 A Ptot Power dissipation Tl = 65 °C 200 mW Tstg Storage temperature range -65 to + 150 °C Tj Operating junction temperature range -65 to + 125 °C TL Maximum temperature for soldering during 15 s 260 °C Value Unit 300 °C/W Table 2. Thermal resistance Symbol Rth(j-l) Parameter Junction to leads Table 3. Static electrical characteristics Symbol VBR Test conditions Tj = 25 °C; IR = 100 µA Tj = 25 °C; IF = 200 mA 30 - Max. Unit V - 1 - 0.4 - 0.65 - 0.33 Tj = 25 °C; IF =15 mA - 0.45 Tj = 25 °C, VR = 25 V - 0.5 Tj = 100 °C, VR = 25 V - 100 Typ. Max. TMMBAT42FILM Tj = 25 °C; IF = 50 mA Tj = 25 °C; IF = 2 mA IR(1) Typ. All types Tj = 25 °C; IF =10 mA VF(1) Min. 0.26 V TMMBAT43FILM µA 1. Pulse test: tp = 380 µs δ < 2% Table 4. Dynamic characteristics Symbol 2/7 Test conditions C Tj = 25 °C; VR = 1 V; f = 1 MHz trr Tj = 25 °C; IF =10 mA; IR = 10 mA; IRR = 1 mA RL = 100 Ω DocID3497 Rev 3 Min. 7 Unit pF 5 ns TMMBAT42 - TMMBAT43 Characteristics Figure 1. Forward voltage drop versus forward Figure 2. Forward voltage drop versus forward current (typical values, high level) current (typical values) ( ,)$  7  ƒ& M ,)$  7  ƒ& M  (   7  ƒ& M (   7  ƒ& M  (  7  ƒ& M 9)9  (               Figure 3. Leakage current versus reverse voltage applied (typical values)   9)9           Figure 4. Junction capacitance versus reverse voltage applied (typical values) ,5—$ &S)  ( ) 0+] 926& P9506 7M ƒ& 7M ƒ& (  7M ƒ& ( 7M ƒ& ( 7M ƒ& 7M ƒ& ( 959 959 (          DocID3497 Rev 3   3/7 7 Package information 2 TMMBAT42 - TMMBAT43 Package information • Ring at cathode end. In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 MINIMELF package information Figure 5. MINIMELF package outline $ ‘' ‘% & & Table 5. MINIMELF mechanical data Dimensions Ref. Inches Min. Typ. Max. Min. Typ. Max. A 3.30 3.50 3.70 0.130 0.138 0.146 ØB 1.59 1.65 1.70 0.063 0.065 0.069 C 0.40 0.50 0.60 0.016 0.020 0.024 ØD 4/7 Millimeters 1.50 DocID3497 Rev 3 0.059 TMMBAT42 - TMMBAT43 Package information Figure 6. Foot print dimensions (in millimeters)    DocID3497 Rev 3 5/7 7 Ordering information 3 TMMBAT42 - TMMBAT43 Ordering information Table 6. Ordering information Order code Package Weight Base qty Delivery mode MINIMELF 40 mg 2500 Tape and reel TMMBAT42FILM TMMBAT43FILM 4 Revision history Table 7. Document revision history 6/7 Date Revision Changes Aug-1999 1A 31-Jul-2014 2 Reformatted to current standards. Added ordering information. 27-Jul-2015 3 Updated MINIMELF package information and reformatted to current standard. Updated Figure 1, Figure 2, Figure 3, and Figure 4. Last issue. DocID3497 Rev 3 TMMBAT42 - TMMBAT43 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved DocID3497 Rev 3 7/7 7