TN2540-12G

TN2540-12G Datasheet Standard SCR, D²PAK, 25 A, 1200 V Features A G • Max. blocking voltage = VDRM, VRRM = 1200 V • IGT maximum = 40 mA • High static and dynamic commutation at Tj = 125 °C – – K • A A D²PAK dl/dt = 50 A/µs dV/dt = 1500 V/µs ECOPACK®2 compliant (RoHS and HF compliance) Applications G K • • • • • • • • • • • Solar Wind renewable energy inverters Solid State Relay (SSR) Uninterruptible Power Supply (UPS) AC DC Inrush Current Limiter (ICL) Battery charger AC DC voltage controlled rectifier Industrial welding systems Off board automotive battery charger Soft starter General purpose motor control Product status link Description TN2540-12G Product summary IT(RMS) 25 A VDRM, VRRM 1200 V IGT 40 mA Tj 125 °C Available in SMD D²PAK with anode in backside. The TN2540-12G SCR is suitable in industrial applications where high immunity is required with a lower gate current. DS12791 - Rev 1 - October 2018 For further information contact your local STMicroelectronics sales office. www.st.com TN2540-12G Characteristics 1 Characteristics Table 1. Absolute maximum ratings (limiting values), Tj = 25 °C unless otherwise specified Symbol VDRM/VRRM IT(RMS) Parameter Repetitive peak off-state voltage (50-60 Hz) On-state RMS current (180° conduction angle) IT(AV) Average on-state current (180° conduction angle) ITSM Non repetitive surge peak on-state current I2t dl/dt IGM PG(AV) Tstg Tj Tj = 125 °C Tc = 102 °C Value Unit 1200 V 25 16 A tp = 8.3 ms 314 tp = 10 ms 300 tp = 10 ms 450 A2s f = 60 Hz 50 A/µs Tj = 125 °C 4 A Tj = 125 °C 1 W Storage junction temperature range -40 to +150 °C Operating junction temperature range -40 to +125 °C I2t value for fusing IG = 2 x IGT, tr ≤ 100 ns Critical rate of rise of on-state current tp = 20 µs Peak gate current Average gate power dissipation A Table 2. Electrical characteristics (Tj = 25 °C unless otherwise specified) Symbol IGT Test conditions VD = 12 V, RL = 33 Ω VGT Unit Min. 4 Max. 40 Max. 1.3 V Min. 0.2 V mA VGD VD = VDRM, RL = 3.3 kΩ IH IT = 500 mA, gate open Max. 80 mA IL IG = 1.2 x IGT Max. 90 mA Min. 1500 V/µs Value Unit dV/dt Tj = 125 °C Value VD = 67 % VDRM, gate open Tj = 125 °C Table 3. Static electrical characteristics Symbol VTM ITM = 50 A, tp = 380 µs Tj = 25 °C Max. 1.60 VTO Threshold voltage Tj = 125 °C Max. 0.85 RD Dynamic resistance Tj = 125 °C Max. 14 mΩ 10 µA 6 mA IDRM, IRRM DS12791 - Rev 1 Test conditions VOUT = 1200 V Tj = 25 °C Tj = 125 °C Max. V page 2/10 TN2540-12G Characteristics (curves) Table 4. Thermal resistance parameter Symbol Parameter Rth(j-c) 1.1 Thermal resistance Junction to case (DC) Max. Value Unit 1.0 °C/W Characteristics (curves) Figure 1. Maximum average power dissipation versus average on-state current 24 P(W) 28 26 24 22 20 18 16 14 12 10 8 6 4 2 0 22 20 18 16 14 12 10 8 6 4 2 IT(AV) (A) 0 0 2 4 6 8 10 12 14 16 Figure 3. Average and D.C. on state current versus ambient temperature 3.5 Figure 2. Average and DC on-state current versus case temperature IT(AV)(A) IT(AV)(A) D.C α = 180 ° TCASE(°C) 0 25 50 100 125 Figure 4. Relative variation of thermal impedance junction to case 1.0E+00 K=[Z th(j-c) /Rth(j-c) ] D.C Zth(j-c) 3.0 2.5 75 α = 180 ° 2.0 1.0E-01 1.5 1.0 0.5 Tamb (°C) t P(s) 0.0 0 DS12791 - Rev 1 25 50 75 100 125 1.0E-02 1.0E-03 1.0E-02 1.0E-01 1.0E+00 1.0E+01 1.0E+02 1.0E+03 page 3/10 TN2540-12G Characteristics (curves) Figure 5. Relative variation of gate trigger and holding current versus junction temperature 2.5 Figure 6. Surge peak on-state current versus number of cycles ITSM(A) IGT, IH , IL[T j]/I GT, IH , IL[T j = 25 °C] 350 300 2.0 250 I GT 1.5 IH & I L 1.0 Non repetitive Tj initial = 25 °C 200 150 100 0.5 50 Repetitive TC = 102 °C Tj(°C) 0.0 Number of cycles 0 -40 -20 0 20 40 60 80 100 120 140 Figure 7. Non repetitive surge peak on-state current for a sinusoidal pulse with width tp < 10 ms 10000 1 dI/dt limitation: 50 A/µs 100 1000 Figure 8. On-state characteristics (maximum values) 1000 ITSM(A) 10 ITM (A) Tj initial = 25 °C 100 ITSM 1000 10 100 0.01 DS12791 - Rev 1 t P(ms) 0.10 Tj max : Vto = 0.85V Rd = 14mΩ VTM (V) 1 1.00 10.00 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 page 4/10 TN2540-12G Package information 2 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 2.1 D²PAK package information • • • ECOPACK®2 compliant Lead-free package leads finishing Molding compound resin is halogen-free and meets UL standard level V0 Figure 9. D²PAK package outline A E E1 E2 H D D1 L2 c2 2 3 D2 L3 1 b2 b e Max resin gate protrusion: 0.5 mm (1) G A1 A2 A3 L R Gauge Plane V2 c (1) Resin gate is accepted in each of position shown on the drawing, or their symmetrical. DS12791 - Rev 1 page 5/10 TN2540-12G D²PAK package information Table 5. D²PAK package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. A 4.30 4.60 0.1693 0.1811 A1 2.49 2.69 0.0980 0.1059 A2 0.03 0.23 0.0012 A3 0.25 0.0091 0.0098 b 0.70 0.93 0.0276 0.0366 b2 1.25 1.7 0.0492 0.0669 c 0.45 0.60 0.0177 0.0236 c2 1.21 1.36 0.0476 0.0535 D 8.95 9.35 0.3524 0.3681 D1 7.50 8.00 0.2953 0.3150 D2 1.30 1.70 0.0512 0.0669 e 2.54 E 10.00 10.28 0.3937 0.4047 E1 8.30 8.70 0.3268 0.3425 E2 6.85 7.25 0.2697 0.2854 G 4.88 5.28 0.1921 0.2079 H 15 15.85 0.5906 0.6240 L 1.78 2.28 0.0701 0.0898 L2 1.27 1.40 0.0500 0.0551 L3 1.40 1.75 0.0551 0.0689 R V2(2) 0.10000 0.40 0° 0.0157 8° 0° 8° 1. Dimensions in inches are given for reference only 2. Degrees DS12791 - Rev 1 page 6/10 TN2540-12G D²PAK package information Figure 10. D²PAK recommended footprint (dimensions are in mm) 16.90 10.30 5.08 1.30 8.90 3.70 Figure 11. D²PAK stencil definitions(dimensions are in mm) DS12791 - Rev 1 page 7/10 TN2540-12G Ordering information 3 Ordering information Figure 12. Ordering information scheme TN 25 40 - 12 - G -TR Standard SCR series RMS current 25 = 25 A Gate current 40 = 40 mA Voltage 12 = 1200 V Package G = D²PAK Packing mode -TR = Tape and reel Blank = Tube Table 6. Ordering information Order code TN2540-12G-TR TN2540-12G DS12791 - Rev 1 Marking Package Weight TN2540-12G D²PAK 1.6 g Base qty. Delivery mode 1000 Tape and Reel 50 Tube page 8/10 TN2540-12G Revision history Table 7. Document revision history DS12791 - Rev 1 Date Version 18-Oct-2018 1 Changes Initial release. page 9/10 TN2540-12G IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2018 STMicroelectronics – All rights reserved DS12791 - Rev 1 page 10/10