TS1220-600T

TS1220 Sensitive 12 A SCRs Datasheet - production data A Applications K   G A A K A   Capacitive ignition circuit for motorcycle engine DC brush motor drive for power tool or kitchen appliance Gas ignitor circuit Regulator driver for battery charger Description DPAK G IPAK K A G A Thanks to highly sensitive triggering levels, the 12 A SCR series is suitable to fit all modes of control, found in applications such as overvoltage crowbar protection, motor control circuits in power tools and kitchen aids, inrush current limiting circuits, capacitive discharge ignition and voltage regulation circuits. Available in through-hole or surface-mount packages, they provide an optimized performance in a limited space. K TO-220AB A Table 1: Device summary Order code G VDRM/VRRM TS1220-600B Features     TS1220-600B-TR On-state RMS current, IT(RMS) 12 A Repetitive peak off-state voltage, VDRM/VRRM 600 V Triggering gate current, IGT 200 µA ECOPACK®2 compliant component August 2016 TS1220-600H TS1220-600T DocID027645 Rev 2 This is information on a product in full production. 600 V IGT Package 0.2 mA DPAK 0.2 mA DPAK 0.2 mA IPAK 0.2 mA TO-220AB 1/14 www.st.com Characteristics 1 TS1220 Characteristics Table 2: Absolute ratings (limiting values) Symbol IT(RMS) Parameter Value Unit On-state RMS current (180° conduction angle) Tc = 105 °C 12 A IT(AV) Average on-state current (180° conduction angle) Tc = 105 °C 8 A ITSM Non repetitive surge peak on-state current tp = 8.3 ms I2t value for fusing tp = 10 ms Tj = 25 °C 60 A2s Critical rate of rise of on-state current IG = 2 x IGT, tr ≤ 100 ns F = 60 Hz Tj = 125 °C 50 A/µs Peak gate current tp = 20 µs Tj = 125 °C 4 A Tj = 125 °C 1 W I2 t dI/dt IGM PG(AV) Tstg Tj tp = 10 ms Average gate power dissipation 115 Tj = 25 °C 110 Storage junction temperature range - 40 to + 150 Operating junction temperature range - 40 to + 125 A °C Table 3: Sensitive electrical characteristics (Tj = 25 °C, unless otherwise specified) Symbol IGT VGT Test conditions Unit VD = 12 V, RL = 140 Ω MAX. 200 µA MAX. 0.8 V MIN. 0.1 V VGD VD = VDRM, RL = 3.3 kΩ, RGK = 220 Ω VRG IRG = 10 µA MIN. 8 V IH IT = 50 mA, RGK = 1 kΩ MAX. 5 mA IL IG = 1 mA, RGK = 1 kΩ MAX. 6 mA Tj = 125 °C VD = 67% VDRM, RGK = 220 Ω Tj =125 °C MIN. 5 V/µs VTM ITM = 24 A tp = 380 µs Tj = 25 °C MAX. 1.6 V Vt0 Threshold voltage Tj = 125 °C MAX. 0.85 V Rd Dynamic resistance Tj = 125 °C MAX. 30 mΩ 5 µA 2 mA Value Unit DPAK, IPAK, TO-220AB 1.3 °C/W DPAK 70 IPAK 100 TO-220AB 60 dV/dt IDRM IRRM Tj = 25 °C VDRM = VRRM, RGK = 1 kΩ Tj = 125 °C MAX. Table 4: Thermal resistance Symbol Rth(j-c) Parameter Junction to case (DC) S = 0.5 Rth(j-a) cm2(1) Junction to ambient (DC) Notes: (1)S = Copper surface under tab 2/14 DocID027645 Rev 2 °C/W TS1220 1.1 Characteristics Characteristics (curves) Figure 1: Maximum average power dissipation versus average on-state current Figure 2: Average and DC on-state current versus case temperature Figure 3: Average and DC on-state current versus ambient temperature (DPAK) Figure 4: Relative variation of thermal impedance junction to case versus pulse duration Figure 5: Relative variation of thermal impedance junction to ambient versus pulse duration Figure 6: Relative variation of gate trigger and holding current versus junction temperature DocID027645 Rev 2 3/14 Characteristics TS1220 Figure 7: Relative variation of holding current versus gate-cathode resistance (typical values) Figure 8: Relative variation of dV/dt immunity versus gate-cathode resistance (typical values) Figure 9: Relative variation of dV/dt immunity current versus gate-cathode capacitance (typical values) Figure 10: Surge peak on-state current versus number of cycles Figure 11: Non-repetitive surge peak on-state current and corresponding values versus sinusoidal pulse width Figure 12: On-state characteristics (maximum values) 4/14 DocID027645 Rev 2 TS1220 Characteristics Figure 13: Thermal resistance junction to ambient versus copper surface under tab (DPAK) DocID027645 Rev 2 5/14 Package information 2 TS1220 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK ® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Lead free lead plating; halogen free molding compound. 2.1 DPAK package mechanical data A Figure 14: DPAK package outline E b4 H D D1 L2 c2 L4 A1 e b c e1 A2 V2 L 6/14 DocID027645 Rev 2 E1 TS1220 Package information Table 5: DPAK mechanical data Inches(1) mm Dim. Min. Typ. Max. Min. Typ. Max. A 2.18 2.40 0.0858 0.0945 A1 0.90 1.10 0.0354 0.0433 A2 0.03 0.23 0.0012 0.0091 b 0.64 0.90 0.0252 0.0354 b4 4.95 5.46 0.1949 0.2150 c 0.46 0.61 0.0181 0.0240 c2 0.46 0.60 0.0181 0.0240 D 5.97 6.22 0.2350 0.2449 D1 4.95 5.60 0.1949 0.2205 E 6.35 6.73 0.2500 0.2650 E1 4.32 5.50 0.1701 0.2165 e 2.286 0.0900 e1 4.40 4.70 0.1732 0.1850 H 9.35 10.40 0.3681 0.4094 L 1.00 1.78 0.0394 0.0701 L2 1.27 0.0500 L4 0.60 1.02 0.0236 0.0402 V2 -8° 8° -8° 8° Notes: (1)Inch dimensions are for reference only. Figure 15: DPAK recommended footprint (dimensions are in mm) DocID027645 Rev 2 7/14 Package information 2.2 TS1220 IPAK package information Figure 16: IPAK (TO-251) package outline This package drawing may slightly differ from the physical package. However, all the specified dimensions are guaranteed. 8/14 DocID027645 Rev 2 TS1220 Package information Table 6: IPAK (TO-251) package mechanical data Dimensions Ref. Inches(1) Millimiters Min. Typ. Max. Min. Typ. Max. A 2.20 2.40 0.0866 0.0945 A1 0.90 1.10 0.0354 0.0433 b 0.64 0.90 0.0252 0.0354 b2 0.95 b4 5.20 B5 5.43 0.0374 0.2047 0.30 0.2138 0.0125 c 0.45 0.60 0.0177 0.0236 c2 0.46 0.60 0.0181 0.0236 D 6.00 6.20 0.2362 0.2441 E 6.40 6.65 0.2520 0.2618 e 2.28 e1 4.40 H 0.0898 4.60 0.1732 16.10 0.1811 0.6339 L 9.00 9.60 0.3545 0.3780 L1 0.80 1.20 0.0315 0.0472 L2 0.80 V1 10° 1.25 0.0315 0.0492 10° Notes: (1)Inch dimensions are for reference only. DocID027645 Rev 2 9/14 Package information 2.3 TS1220 TO-220AB package information Figure 17: TO-220AB package outline 10/14 DocID027645 Rev 2 TS1220 Package information Table 7: TO-220AB package mechanical data Dimensions Ref. Inches(1) Millimeters Min. Max. Min. Max. A 4.40 4.60 0.1732 0.1811 b 0.61 0.88 0.0240 0.0346 b1 1.14 1.70 0.0449 0.0669 c 0.48 0.70 0.0189 0.0276 D 15.25 15.75 0.6004 0.6201 D1 1.27 typ. 0.0500 typ. E 10.00 10.40 0.3937 0.4094 e 2.40 2.70 0.0945 0.1063 e1 4.95 5.15 0.1949 0.2028 F 1.23 1.32 0.0484 0.0520 H1 6.20 6.60 0.2441 0.2598 J1 2.40 2.72 0.0945 0.1071 L 13.00 14.00 0.5118 0.5512 L1 3.50 3.93 0.1378 0.1547 L20 16.40 typ. 0.6457 typ. L30 28.90 typ. 1.1378 typ. ØP 3.75 3.85 0.1476 0.1516 Q 2.65 2.95 0.1043 0.1161 Notes: (1)Inch dimensions are for reference only. DocID027645 Rev 2 11/14 Ordering information 3 TS1220 Ordering information Figure 18: TS1220 series TS 12 20 - 600 B - TR Sensitive SCR series Current 12 = 12 A Sensitivity 20 = 200 µA Voltage 600 = 600 V Package B = DPAK H = IPAK T = TO-220AB Packing mode Blank = Tube -TR = Tape and reel Table 8: Ordering information Order code 12/14 Marking Package Weight Base qty Delivery mode TS1220-600B TS12 20600 DPAK 0.3 g 75 Tube TS1220-600B-TR TS12 20600 DPAK 0.3 g 2500 Tape and reel TS1220-600H TS12 20600 IPAK 0.3 g 75 Tube TS1220-600T TS1220600T TO-220AB 2.3 g 50 Tube DocID027645 Rev 2 TS1220 4 Revision history Revision history Table 9: Document revision history Date Revision 08-Apr-2015 1 First issue. 2 Added section Applications and updated Features and in Table 1: "Device summary" in cover page. Updated Section 3: "Package information". Minor text changes. 03-Aug-2016 Changes DocID027645 Rev 2 13/14 TS1220 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved 14/14 DocID027645 Rev 2