TS27L2CPT

TS27L2C,I,M PRECISION VERY LOW POWER CMOS DUAL OPERATIONAL AMPLIFIERS ■ VERY LOW POWER CONSUMPTION : 10µA/op ■ OUTPUT VOLTAGE CAN SWING TO GROUND ■ EXCELLENT PHASE MARGIN ON CAPACITIVE LOADS N DIP8 (Plastic Package) ■ STABLE AND LOW OFFSET VOLTAGE ■ THREE INPUT OFFSET VOLTAGE SELECTIONS DESCRIPTION D SO8 (Plastic Micropackage) These devices are low cost, low power dual operational amplifiers designed to operate with single or dual supplies. These operational amplifiers use the ST silicon gate CMOS process allowing an excellent consumption-speed ratio. These series are ideally suited for low consumption applications. Three power consumptions are available allowing to have always the best consumption-speed ratio: ❑ ICC = 10µA/amp.: TS27L2 (very low power) ❑ ICC = 150µA/amp.: TS27M2 (low power) P TSSOP8 (Thin Shrink Small Outline Package) PIN CONNECTIONS (top view) ❑ ICC = 1mA/amp.: TS272 (standard) These CMOS amplifiers offer very high input impedance and extremely low input currents. The major advantage versus JFET devices is the very low input currents drift with temperature (see figure 2). ORDER CODE 1 8 2 - 3 + 4 7 - 6 + 5 Package Part Number Temperature Range TS27L2C/AC/BC 0°C, +70°C TS27L2I/AI/BI -40°C, +125°C TS27L2M/AM/BM -55°C, +125°C Example : TS27L2ACN N D P • • • • • • • • • N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT) P = Thin Shrink Small Outline Package (TSSOP) - only available in Tape & Reel (PT) November 2001 1 - Output 1 2 - Inverting Input 1 3 - Non-inverting Input 1 4 - V CC 5 - Non-inverting Input 2 6 - Inverting Input 2 7 - Output 2 8 - V CC + 1/9 TS27L2C,I,M BLOCK DIAGRAM VCC Current source xI Input differential Output stage Second stage Output VCC E E ABSOLUTE MAXIMUM RATINGS Symbol VCC + Vid Parameter Supply Voltage TS27L2C/AC/BC 1) 2) TS27L2I/AI/BI TS27L2M/AM/BM Unit 18 V ±18 V -0.3 to 18 V Output Current for VCC+ ≥ 15V ±30 mA Input Current ±5 mA Differential Input Voltage Vi Input Voltage Io Iin 3) Toper Operating Free-Air Temperature Range Tstg Storage Temperature Range 0 to +70 -40 to +125 -55 to +125 -65 to +150 °C °C 1. All values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input and the output voltages must never exceed the magnitude of the positive supply voltage. OPERATING CONDITIONS Symbol Parameter VCC+ Supply Voltage Vicm Common Mode Input Voltage Range 2/9 Value Unit 3 to 16 V 0 to VCC+ - 1.5 V T20 T19 T17 T24 T21 T 18 R2 T 25 VCC T 22 T 23 T 26 T29 T 28 T27 Input T3 T1 T5 VCC T4 T2 C1 Input R1 T7 T6 T9 T8 T 13 T11 T 10 T 14 T 12 T16 Output T 15 TS27L2C,I,M SCHEMATIC DIAGRAM (for 1/2 TS27L2) 3/9 TS27L2C,I,M ELECTRICAL CHARACTERISTICS VCC+ = +10V, VCC-= 0V, Tamb = +25°C (unless otherwise specified) TS27L2C/AC/BC Symbol Parameter Min. Input Offset Voltage VO = 1.4V, Vic = 0V Vio DVio Iio Iib Tmin ≤ Tamb ≤ Tmax TS27L2C/I/M TS27L2AC/AI/AM TS27L2B/C/I/M TS27L2C/I/M TS27L2AC/AI/AM TS27L2B/C/I/M Typ. Max. 1.1 0.9 0.25 10 5 2 12 6.5 3 Input Offset Voltage Drift 2 Input Offset Current note 1) Vic = 5V, VO = 5V Tmin ≤ Tamb ≤ Tmax 1 Input Bias Current - see note 1 Vic = 5V, VO = 5V Tmin ≤ Tamb ≤ Tmax 1 VOH High Level Output Voltage Vid = 100mV, RL = 1MΩ Tmin ≤ Tamb ≤ Tmax VOL Low Level Output Voltage Vid = -100mV Avd Large Signal Voltage Gain ViC = 5V, RL = 1MΩ, Vo = 1V to 6V Tmin ≤ Tamb ≤ Tmax TS27L2I/AI/BI TS27L2M/AM/BM Min. Typ. 1.1 0.9 0.25 8.8 8.6 100 60 40 100 CMR Common Mode Rejection Ratio ViC = 1V to 7.4V, Vo = 1.4V 65 80 65 80 SVR Supply Voltage Rejection Ratio VCC+ = 5V to 10V, Vo = 1.4V 60 80 60 80 MHz 10 dB dB 15 18 µA Output Short Circuit Current Vo = 0V, Vid = 100mV 60 60 Isink Output Sink Current Vo = VCC, Vid = -100mV 45 45 SR Slew Rate at Unity Gain RL = 1MΩ, CL = 100pF, Vi = 3 to 7V 0.04 0.04 φm Phase Margin at Unity Gain Av = 40dB, RL = 1MΩ, CL = 100pF 45 45 KOV Overshoot Factor 30 30 % Equivalent Input Noise Voltage f = 1kHz, Rs = 100Ω 68 68 nV -----------Hz Channel Separation 120 120 dB Vo1/Vo2 4/9 V/mV 0.1 15 17 mV Io en 1. V 50 0.1 10 pA 9 Gain Bandwidth Product Av = 40dB, RL = 1MΩ, CL = 100pF, fin = 100kHz Supply Current (per amplifier) Av = 1, no load, Vo = 5V Tmin ≤ Tamb ≤ Tmax pA 300 GBP ICC µV/°C 1 9 mV 200 50 60 45 10 5 2 12 6.5 3.5 1 150 8.8 8.7 Max. 2 100 Unit Maximum values including unavoidable inaccuracies of the industrial test. mA mA V/µs Degrees TS27L2C,I,M TYPICAL CHARACTERISTICS Figure 1 : Supply Current (each amplifier) versus Supply Voltage Figure 3b : High Level Output Voltage versus High Level Output Current 20 15 Tamb = 25 °C AV = 1 VO = VCC / 2 OUTPUT VOLTAGE, V OH (V) SUPPLY CURRENT, I CC (µA) 20 10 5 0 4 8 12 Tamb = 25° C V id = 100mV 16 VCC = 16V 12 8 VCC = 10V 4 0 -50 16 SUPPLY VOLTAGE, VCC (V) Figure 2 : Input Bias Current versus Free Air Temperature 1 .0 VCC = 10V V i = 5V O U T P U T V O L T A G E , V O L (V ) INPUT BIAS CURRENT, IIB (pA) 0 Figure 4a : Low Level Output Voltage versus Low Level Output Current 100 10 1 25 50 75 100 TEMPERATURE, Tamb (°C) 0 .8 V CC = 3V 0 .6 V CC = 5V 0 .4 T amb = 2 5 °C V ic = 0 .5 V V id = -1 0 0 m V 0 .2 0 125 1 2 3 O U T P U T C U R R E N T , I O L (m A ) Figure 3a : High Level Output Voltage versus High Level Output Current Figure 4b : Low Level Output Voltage versus Low Level Output Current 3 O U T P U T V O L T A G E , V OL (V ) 5 OUTPUT VOLTAGE, VOH (V) -40 -30 -20 -10 OUTPUT CURRENT, I OH (mA) Tamb = 25° C V id = 100mV 4 3 VCC= 5V 2 VCC = 3V 1 0 -10 -8 -6 -4 -2 OUTPUT CURRENT, I OH (mA) 0 V C C = 10V VC C = 1 6 V 2 1 T amb = 2 5 °C V i = 0 .5 V Vid = -1 0 0 m V 0 4 8 12 16 20 O U T P U T C U R R E N T , I OL (m A ) 5/9 TS27L2C,I,M 40 0 G A IN G A IN (d B ) 30 45 PHASE 20 Phase Margin T amb = 2 5 °C V CC+ = 1 0 V R L = 1 MΩ C L = 100pF A VCL = 1 0 0 10 0 135 2 10 3 180 Gain Bandwidth Product -1 0 10 90 10 4 10 5 10 6 10 P H A S E (D e g re e s ) 50 7 Figure 8 : Phase Margin versus Capacitive Load P H A S E M A R G IN , φ m (D e g re e s ) Figure 5 : Open Loop Frequency Response and Phase Shift 80 T amb = 2 5 °C R L = 1MΩ AV = 1 V CC= 1 0 V 70 60 50 40 0 F R E Q U E N C Y , f (H z ) 20 40 60 80 C A P A C IT A N C E , C L (p F ) Figure 9 : Slew Rate versus Supply Voltage 120 0 .0 5 T amb = 2 5 °C R L = 1M Ω C = 100pF L AV = 1 100 80 S L E W R A T E S , S R (V /µ s ) G A IN B A N D W . P R O D ., G B P (M H z ) Figure 6 : Gain Bandwidth Product versus Supply Voltage 100 60 40 T amb = 2 5 °C R L = 1M Ω C = 100pF L SR 0 .0 4 SR 0 .0 3 0 .0 2 0 4 8 12 4 16 6 8 10 12 14 S U P P L Y V O L T A G E , VCC (V ) 16 S U P P L Y V O L T A G E , V CC (V ) 60 T amb = 2 5 °C R L = 1 MΩ C = 100pF L AV = 1 50 40 30 300 VCC = 1 0 V Tamb= 2 5 °C R S= 1 0 0 Ω 200 100 0 0 4 8 12 S U P P L Y V O L T A G E , V CC (V ) 6/9 Figure 10 : Input Voltage Noise versus Frequency E Q U IV A L E N T IN P U T N O IS E V O L T A G E (n V /V H z ) P H A S E M A R G IN , φ m (D e g re e s ) Figure 7 : Phase Margin versus Supply Voltage 16 1 10 100 F R E Q U E N C Y (H z ) 1000 TS27L2C,I,M PACKAGE MECHANICAL DATA 8 PINS - PLASTIC DIP Millimeters Inches Dim. Min. A a1 B b b1 D E e e3 e4 F i L Z Typ. Max. Min. 3.32 0.51 1.15 0.356 0.204 1.65 0.55 0.304 10.92 9.75 7.95 0.020 0.045 0.014 0.008 Max. 0.065 0.022 0.012 0.430 0.384 0.313 2.54 7.62 7.62 3.18 Typ. 0.131 0.100 0.300 0.300 6.6 5.08 3.81 1.52 0.125 0260 0.200 0.150 0.060 7/9 TS27L2C,I,M PACKAGE MECHANICAL DATA 8 PINS - PLASTIC MICROPACKAGE (SO) s b1 b a1 A a2 C c1 a3 L E e3 D M 5 1 4 F 8 Millimeters Inches Dim. Min. A a1 a2 a3 b b1 C c1 D E e e3 F L M S 8/9 Typ. Max. 0.65 0.35 0.19 0.25 1.75 0.25 1.65 0.85 0.48 0.25 0.5 4.8 5.8 5.0 6.2 0.1 Min. Typ. Max. 0.026 0.014 0.007 0.010 0.069 0.010 0.065 0.033 0.019 0.010 0.020 0.189 0.228 0.197 0.244 0.004 45° (typ.) 1.27 3.81 3.8 0.4 0.050 0.150 4.0 1.27 0.6 0.150 0.016 8° (max.) 0.157 0.050 0.024 TS27L2C,I,M PACKAGE MECHANICAL DATA 8 PINS - THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP) k c 0.25mm .010 inch GAGE PLANE L1 L L L1 C SEATING PLANE E1 A E A2 A1 5 4 4 5 D b e 8 1 8 1 PIN 1 IDENTIFICATION Millimeters Inches Dim. Min. A A1 A2 b c D E E1 e k l L L1 0.05 0.80 0.19 0.09 2.90 4.30 0° 0.50 0.45 Typ. 1.00 3.00 6.40 4.40 0.65 0.60 0.600 1.000 Max. Min. 1.20 0.15 1.05 0.30 0.20 3.10 0.01 0.031 0.007 0.003 0.114 4.50 0.169 8° 0.75 0.75 0° 0.09 0.018 Typ. 0.039 0.118 0.252 0.173 0.025 0.0236 0.024 0.039 Max. 0.05 0.006 0.041 0.15 0.012 0.122 0.177 8° 0.030 0.030 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States © http://www.st.com 9/9